1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Low-level ALSA driver for the ENSONIQ SoundScape
4 * Copyright (c) by Chris Rankin
5 *
6 * This driver was written in part using information obtained from
7 * the OSS/Free SoundScape driver, written by Hannu Savolainen.
8 */
9
10 #include <linux/init.h>
11 #include <linux/err.h>
12 #include <linux/io.h>
13 #include <linux/isa.h>
14 #include <linux/delay.h>
15 #include <linux/firmware.h>
16 #include <linux/pnp.h>
17 #include <linux/spinlock.h>
18 #include <linux/module.h>
19 #include <asm/dma.h>
20 #include <sound/core.h>
21 #include <sound/wss.h>
22 #include <sound/mpu401.h>
23 #include <sound/initval.h>
24
25
26 MODULE_AUTHOR("Chris Rankin");
27 MODULE_DESCRIPTION("ENSONIQ SoundScape driver");
28 MODULE_LICENSE("GPL");
29 MODULE_FIRMWARE("sndscape.co0");
30 MODULE_FIRMWARE("sndscape.co1");
31 MODULE_FIRMWARE("sndscape.co2");
32 MODULE_FIRMWARE("sndscape.co3");
33 MODULE_FIRMWARE("sndscape.co4");
34 MODULE_FIRMWARE("scope.cod");
35
36 static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX;
37 static char* id[SNDRV_CARDS] = SNDRV_DEFAULT_STR;
38 static long port[SNDRV_CARDS] = SNDRV_DEFAULT_PORT;
39 static long wss_port[SNDRV_CARDS] = SNDRV_DEFAULT_PORT;
40 static int irq[SNDRV_CARDS] = SNDRV_DEFAULT_IRQ;
41 static int mpu_irq[SNDRV_CARDS] = SNDRV_DEFAULT_IRQ;
42 static int dma[SNDRV_CARDS] = SNDRV_DEFAULT_DMA;
43 static int dma2[SNDRV_CARDS] = SNDRV_DEFAULT_DMA;
44 static bool joystick[SNDRV_CARDS];
45
46 module_param_array(index, int, NULL, 0444);
47 MODULE_PARM_DESC(index, "Index number for SoundScape soundcard");
48
49 module_param_array(id, charp, NULL, 0444);
50 MODULE_PARM_DESC(id, "Description for SoundScape card");
51
52 module_param_hw_array(port, long, ioport, NULL, 0444);
53 MODULE_PARM_DESC(port, "Port # for SoundScape driver.");
54
55 module_param_hw_array(wss_port, long, ioport, NULL, 0444);
56 MODULE_PARM_DESC(wss_port, "WSS Port # for SoundScape driver.");
57
58 module_param_hw_array(irq, int, irq, NULL, 0444);
59 MODULE_PARM_DESC(irq, "IRQ # for SoundScape driver.");
60
61 module_param_hw_array(mpu_irq, int, irq, NULL, 0444);
62 MODULE_PARM_DESC(mpu_irq, "MPU401 IRQ # for SoundScape driver.");
63
64 module_param_hw_array(dma, int, dma, NULL, 0444);
65 MODULE_PARM_DESC(dma, "DMA # for SoundScape driver.");
66
67 module_param_hw_array(dma2, int, dma, NULL, 0444);
68 MODULE_PARM_DESC(dma2, "DMA2 # for SoundScape driver.");
69
70 module_param_array(joystick, bool, NULL, 0444);
71 MODULE_PARM_DESC(joystick, "Enable gameport.");
72
73 #ifdef CONFIG_PNP
74 static int isa_registered;
75 static int pnp_registered;
76
77 static const struct pnp_card_device_id sscape_pnpids[] = {
78 { .id = "ENS3081", .devs = { { "ENS0000" } } }, /* Soundscape PnP */
79 { .id = "ENS4081", .devs = { { "ENS1011" } } }, /* VIVO90 */
80 { .id = "" } /* end */
81 };
82
83 MODULE_DEVICE_TABLE(pnp_card, sscape_pnpids);
84 #endif
85
86
87 #define HOST_CTRL_IO(i) ((i) + 2)
88 #define HOST_DATA_IO(i) ((i) + 3)
89 #define ODIE_ADDR_IO(i) ((i) + 4)
90 #define ODIE_DATA_IO(i) ((i) + 5)
91 #define CODEC_IO(i) ((i) + 8)
92
93 #define IC_ODIE 1
94 #define IC_OPUS 2
95
96 #define RX_READY 0x01
97 #define TX_READY 0x02
98
99 #define CMD_ACK 0x80
100 #define CMD_SET_MIDI_VOL 0x84
101 #define CMD_GET_MIDI_VOL 0x85
102 #define CMD_XXX_MIDI_VOL 0x86
103 #define CMD_SET_EXTMIDI 0x8a
104 #define CMD_GET_EXTMIDI 0x8b
105 #define CMD_SET_MT32 0x8c
106 #define CMD_GET_MT32 0x8d
107
108 enum GA_REG {
109 GA_INTSTAT_REG = 0,
110 GA_INTENA_REG,
111 GA_DMAA_REG,
112 GA_DMAB_REG,
113 GA_INTCFG_REG,
114 GA_DMACFG_REG,
115 GA_CDCFG_REG,
116 GA_SMCFGA_REG,
117 GA_SMCFGB_REG,
118 GA_HMCTL_REG
119 };
120
121 #define DMA_8BIT 0x80
122
123
124 enum card_type {
125 MEDIA_FX, /* Sequoia S-1000 */
126 SSCAPE, /* Sequoia S-2000 */
127 SSCAPE_PNP,
128 SSCAPE_VIVO,
129 };
130
131 struct soundscape {
132 spinlock_t lock;
133 unsigned io_base;
134 int ic_type;
135 enum card_type type;
136 struct resource *io_res;
137 struct resource *wss_res;
138 struct snd_wss *chip;
139
140 unsigned char midi_vol;
141 struct device *dev;
142 };
143
144 #define INVALID_IRQ ((unsigned)-1)
145
146
get_card_soundscape(struct snd_card * c)147 static inline struct soundscape *get_card_soundscape(struct snd_card *c)
148 {
149 return (struct soundscape *) (c->private_data);
150 }
151
152 /*
153 * Allocates some kernel memory that we can use for DMA.
154 * I think this means that the memory has to map to
155 * contiguous pages of physical memory.
156 */
get_dmabuf(struct soundscape * s,struct snd_dma_buffer * buf,unsigned long size)157 static struct snd_dma_buffer *get_dmabuf(struct soundscape *s,
158 struct snd_dma_buffer *buf,
159 unsigned long size)
160 {
161 if (buf) {
162 if (snd_dma_alloc_pages_fallback(SNDRV_DMA_TYPE_DEV,
163 s->chip->card->dev,
164 size, buf) < 0) {
165 dev_err(s->dev,
166 "sscape: Failed to allocate %lu bytes for DMA\n",
167 size);
168 return NULL;
169 }
170 }
171
172 return buf;
173 }
174
175 /*
176 * Release the DMA-able kernel memory ...
177 */
free_dmabuf(struct snd_dma_buffer * buf)178 static void free_dmabuf(struct snd_dma_buffer *buf)
179 {
180 if (buf && buf->area)
181 snd_dma_free_pages(buf);
182 }
183
184 /*
185 * This function writes to the SoundScape's control registers,
186 * but doesn't do any locking. It's up to the caller to do that.
187 * This is why this function is "unsafe" ...
188 */
sscape_write_unsafe(unsigned io_base,enum GA_REG reg,unsigned char val)189 static inline void sscape_write_unsafe(unsigned io_base, enum GA_REG reg,
190 unsigned char val)
191 {
192 outb(reg, ODIE_ADDR_IO(io_base));
193 outb(val, ODIE_DATA_IO(io_base));
194 }
195
196 /*
197 * Write to the SoundScape's control registers, and do the
198 * necessary locking ...
199 */
sscape_write(struct soundscape * s,enum GA_REG reg,unsigned char val)200 static void sscape_write(struct soundscape *s, enum GA_REG reg,
201 unsigned char val)
202 {
203 unsigned long flags;
204
205 spin_lock_irqsave(&s->lock, flags);
206 sscape_write_unsafe(s->io_base, reg, val);
207 spin_unlock_irqrestore(&s->lock, flags);
208 }
209
210 /*
211 * Read from the SoundScape's control registers, but leave any
212 * locking to the caller. This is why the function is "unsafe" ...
213 */
sscape_read_unsafe(unsigned io_base,enum GA_REG reg)214 static inline unsigned char sscape_read_unsafe(unsigned io_base,
215 enum GA_REG reg)
216 {
217 outb(reg, ODIE_ADDR_IO(io_base));
218 return inb(ODIE_DATA_IO(io_base));
219 }
220
221 /*
222 * Puts the SoundScape into "host" mode, as compared to "MIDI" mode
223 */
set_host_mode_unsafe(unsigned io_base)224 static inline void set_host_mode_unsafe(unsigned io_base)
225 {
226 outb(0x0, HOST_CTRL_IO(io_base));
227 }
228
229 /*
230 * Puts the SoundScape into "MIDI" mode, as compared to "host" mode
231 */
set_midi_mode_unsafe(unsigned io_base)232 static inline void set_midi_mode_unsafe(unsigned io_base)
233 {
234 outb(0x3, HOST_CTRL_IO(io_base));
235 }
236
237 /*
238 * Read the SoundScape's host-mode control register, but leave
239 * any locking issues to the caller ...
240 */
host_read_unsafe(unsigned io_base)241 static inline int host_read_unsafe(unsigned io_base)
242 {
243 int data = -1;
244 if ((inb(HOST_CTRL_IO(io_base)) & RX_READY) != 0)
245 data = inb(HOST_DATA_IO(io_base));
246
247 return data;
248 }
249
250 /*
251 * Read the SoundScape's host-mode control register, performing
252 * a limited amount of busy-waiting if the register isn't ready.
253 * Also leaves all locking-issues to the caller ...
254 */
host_read_ctrl_unsafe(unsigned io_base,unsigned timeout)255 static int host_read_ctrl_unsafe(unsigned io_base, unsigned timeout)
256 {
257 int data;
258
259 while (((data = host_read_unsafe(io_base)) < 0) && (timeout != 0)) {
260 udelay(100);
261 --timeout;
262 } /* while */
263
264 return data;
265 }
266
267 /*
268 * Write to the SoundScape's host-mode control registers, but
269 * leave any locking issues to the caller ...
270 */
host_write_unsafe(unsigned io_base,unsigned char data)271 static inline int host_write_unsafe(unsigned io_base, unsigned char data)
272 {
273 if ((inb(HOST_CTRL_IO(io_base)) & TX_READY) != 0) {
274 outb(data, HOST_DATA_IO(io_base));
275 return 1;
276 }
277
278 return 0;
279 }
280
281 /*
282 * Write to the SoundScape's host-mode control registers, performing
283 * a limited amount of busy-waiting if the register isn't ready.
284 * Also leaves all locking-issues to the caller ...
285 */
host_write_ctrl_unsafe(unsigned io_base,unsigned char data,unsigned timeout)286 static int host_write_ctrl_unsafe(unsigned io_base, unsigned char data,
287 unsigned timeout)
288 {
289 int err;
290
291 while (!(err = host_write_unsafe(io_base, data)) && (timeout != 0)) {
292 udelay(100);
293 --timeout;
294 } /* while */
295
296 return err;
297 }
298
299
300 /*
301 * Check that the MIDI subsystem is operational. If it isn't,
302 * then we will hang the computer if we try to use it ...
303 *
304 * NOTE: This check is based upon observation, not documentation.
305 */
verify_mpu401(const struct snd_mpu401 * mpu)306 static inline int verify_mpu401(const struct snd_mpu401 *mpu)
307 {
308 return ((inb(MPU401C(mpu)) & 0xc0) == 0x80);
309 }
310
311 /*
312 * This is apparently the standard way to initialise an MPU-401
313 */
initialise_mpu401(const struct snd_mpu401 * mpu)314 static inline void initialise_mpu401(const struct snd_mpu401 *mpu)
315 {
316 outb(0, MPU401D(mpu));
317 }
318
319 /*
320 * Tell the SoundScape to activate the AD1845 chip (I think).
321 * The AD1845 detection fails if we *don't* do this, so I
322 * think that this is a good idea ...
323 */
activate_ad1845_unsafe(unsigned io_base)324 static void activate_ad1845_unsafe(unsigned io_base)
325 {
326 unsigned char val = sscape_read_unsafe(io_base, GA_HMCTL_REG);
327 sscape_write_unsafe(io_base, GA_HMCTL_REG, (val & 0xcf) | 0x10);
328 sscape_write_unsafe(io_base, GA_CDCFG_REG, 0x80);
329 }
330
331 /*
332 * Tell the SoundScape to begin a DMA transfer using the given channel.
333 * All locking issues are left to the caller.
334 */
sscape_start_dma_unsafe(unsigned io_base,enum GA_REG reg)335 static void sscape_start_dma_unsafe(unsigned io_base, enum GA_REG reg)
336 {
337 sscape_write_unsafe(io_base, reg,
338 sscape_read_unsafe(io_base, reg) | 0x01);
339 sscape_write_unsafe(io_base, reg,
340 sscape_read_unsafe(io_base, reg) & 0xfe);
341 }
342
343 /*
344 * Wait for a DMA transfer to complete. This is a "limited busy-wait",
345 * and all locking issues are left to the caller.
346 */
sscape_wait_dma_unsafe(unsigned io_base,enum GA_REG reg,unsigned timeout)347 static int sscape_wait_dma_unsafe(unsigned io_base, enum GA_REG reg,
348 unsigned timeout)
349 {
350 while (!(sscape_read_unsafe(io_base, reg) & 0x01) && (timeout != 0)) {
351 udelay(100);
352 --timeout;
353 } /* while */
354
355 return sscape_read_unsafe(io_base, reg) & 0x01;
356 }
357
358 /*
359 * Wait for the On-Board Processor to return its start-up
360 * acknowledgement sequence. This wait is too long for
361 * us to perform "busy-waiting", and so we must sleep.
362 * This in turn means that we must not be holding any
363 * spinlocks when we call this function.
364 */
obp_startup_ack(struct soundscape * s,unsigned timeout)365 static int obp_startup_ack(struct soundscape *s, unsigned timeout)
366 {
367 unsigned long end_time = jiffies + msecs_to_jiffies(timeout);
368
369 do {
370 unsigned long flags;
371 int x;
372
373 spin_lock_irqsave(&s->lock, flags);
374 x = host_read_unsafe(s->io_base);
375 spin_unlock_irqrestore(&s->lock, flags);
376 if (x == 0xfe || x == 0xff)
377 return 1;
378
379 msleep(10);
380 } while (time_before(jiffies, end_time));
381
382 return 0;
383 }
384
385 /*
386 * Wait for the host to return its start-up acknowledgement
387 * sequence. This wait is too long for us to perform
388 * "busy-waiting", and so we must sleep. This in turn means
389 * that we must not be holding any spinlocks when we call
390 * this function.
391 */
host_startup_ack(struct soundscape * s,unsigned timeout)392 static int host_startup_ack(struct soundscape *s, unsigned timeout)
393 {
394 unsigned long end_time = jiffies + msecs_to_jiffies(timeout);
395
396 do {
397 unsigned long flags;
398 int x;
399
400 spin_lock_irqsave(&s->lock, flags);
401 x = host_read_unsafe(s->io_base);
402 spin_unlock_irqrestore(&s->lock, flags);
403 if (x == 0xfe)
404 return 1;
405
406 msleep(10);
407 } while (time_before(jiffies, end_time));
408
409 return 0;
410 }
411
412 /*
413 * Upload a byte-stream into the SoundScape using DMA channel A.
414 */
upload_dma_data(struct soundscape * s,const unsigned char * data,size_t size)415 static int upload_dma_data(struct soundscape *s, const unsigned char *data,
416 size_t size)
417 {
418 unsigned long flags;
419 struct snd_dma_buffer dma;
420 int ret;
421 unsigned char val;
422
423 if (!get_dmabuf(s, &dma, PAGE_ALIGN(32 * 1024)))
424 return -ENOMEM;
425
426 spin_lock_irqsave(&s->lock, flags);
427
428 /*
429 * Reset the board ...
430 */
431 val = sscape_read_unsafe(s->io_base, GA_HMCTL_REG);
432 sscape_write_unsafe(s->io_base, GA_HMCTL_REG, val & 0x3f);
433
434 /*
435 * Enable the DMA channels and configure them ...
436 */
437 val = (s->chip->dma1 << 4) | DMA_8BIT;
438 sscape_write_unsafe(s->io_base, GA_DMAA_REG, val);
439 sscape_write_unsafe(s->io_base, GA_DMAB_REG, 0x20);
440
441 /*
442 * Take the board out of reset ...
443 */
444 val = sscape_read_unsafe(s->io_base, GA_HMCTL_REG);
445 sscape_write_unsafe(s->io_base, GA_HMCTL_REG, val | 0x80);
446
447 /*
448 * Upload the firmware to the SoundScape
449 * board through the DMA channel ...
450 */
451 while (size != 0) {
452 unsigned long len;
453
454 len = min(size, dma.bytes);
455 memcpy(dma.area, data, len);
456 data += len;
457 size -= len;
458
459 snd_dma_program(s->chip->dma1, dma.addr, len, DMA_MODE_WRITE);
460 sscape_start_dma_unsafe(s->io_base, GA_DMAA_REG);
461 if (!sscape_wait_dma_unsafe(s->io_base, GA_DMAA_REG, 5000)) {
462 /*
463 * Don't forget to release this spinlock we're holding
464 */
465 spin_unlock_irqrestore(&s->lock, flags);
466
467 dev_err(s->dev, "sscape: DMA upload has timed out\n");
468 ret = -EAGAIN;
469 goto _release_dma;
470 }
471 } /* while */
472
473 set_host_mode_unsafe(s->io_base);
474 outb(0x0, s->io_base);
475
476 /*
477 * Boot the board ... (I think)
478 */
479 val = sscape_read_unsafe(s->io_base, GA_HMCTL_REG);
480 sscape_write_unsafe(s->io_base, GA_HMCTL_REG, val | 0x40);
481 spin_unlock_irqrestore(&s->lock, flags);
482
483 /*
484 * If all has gone well, then the board should acknowledge
485 * the new upload and tell us that it has rebooted OK. We
486 * give it 5 seconds (max) ...
487 */
488 ret = 0;
489 if (!obp_startup_ack(s, 5000)) {
490 dev_err(s->dev,
491 "sscape: No response from on-board processor after upload\n");
492 ret = -EAGAIN;
493 } else if (!host_startup_ack(s, 5000)) {
494 dev_err(s->dev, "sscape: SoundScape failed to initialise\n");
495 ret = -EAGAIN;
496 }
497
498 _release_dma:
499 /*
500 * NOTE!!! We are NOT holding any spinlocks at this point !!!
501 */
502 sscape_write(s, GA_DMAA_REG, (s->ic_type == IC_OPUS ? 0x40 : 0x70));
503 free_dmabuf(&dma);
504
505 return ret;
506 }
507
508 /*
509 * Upload the bootblock(?) into the SoundScape. The only
510 * purpose of this block of code seems to be to tell
511 * us which version of the microcode we should be using.
512 */
sscape_upload_bootblock(struct snd_card * card)513 static int sscape_upload_bootblock(struct snd_card *card)
514 {
515 struct soundscape *sscape = get_card_soundscape(card);
516 unsigned long flags;
517 const struct firmware *init_fw = NULL;
518 int data = 0;
519 int ret;
520
521 ret = request_firmware(&init_fw, "scope.cod", card->dev);
522 if (ret < 0) {
523 dev_err(card->dev, "sscape: Error loading scope.cod");
524 return ret;
525 }
526 ret = upload_dma_data(sscape, init_fw->data, init_fw->size);
527
528 release_firmware(init_fw);
529
530 spin_lock_irqsave(&sscape->lock, flags);
531 if (ret == 0)
532 data = host_read_ctrl_unsafe(sscape->io_base, 100);
533
534 if (data & 0x10)
535 sscape_write_unsafe(sscape->io_base, GA_SMCFGA_REG, 0x2f);
536
537 spin_unlock_irqrestore(&sscape->lock, flags);
538
539 data &= 0xf;
540 if (ret == 0 && data > 7) {
541 dev_err(card->dev,
542 "sscape: timeout reading firmware version\n");
543 ret = -EAGAIN;
544 }
545
546 return (ret == 0) ? data : ret;
547 }
548
549 /*
550 * Upload the microcode into the SoundScape.
551 */
sscape_upload_microcode(struct snd_card * card,int version)552 static int sscape_upload_microcode(struct snd_card *card, int version)
553 {
554 struct soundscape *sscape = get_card_soundscape(card);
555 const struct firmware *init_fw = NULL;
556 char name[14];
557 int err;
558
559 scnprintf(name, sizeof(name), "sndscape.co%d", version);
560
561 err = request_firmware(&init_fw, name, card->dev);
562 if (err < 0) {
563 dev_err(card->dev, "sscape: Error loading sndscape.co%d",
564 version);
565 return err;
566 }
567 err = upload_dma_data(sscape, init_fw->data, init_fw->size);
568 if (err == 0)
569 dev_info(card->dev, "sscape: MIDI firmware loaded %zu KBs\n",
570 init_fw->size >> 10);
571
572 release_firmware(init_fw);
573
574 return err;
575 }
576
577 /*
578 * Mixer control for the SoundScape's MIDI device.
579 */
sscape_midi_info(struct snd_kcontrol * ctl,struct snd_ctl_elem_info * uinfo)580 static int sscape_midi_info(struct snd_kcontrol *ctl,
581 struct snd_ctl_elem_info *uinfo)
582 {
583 uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
584 uinfo->count = 1;
585 uinfo->value.integer.min = 0;
586 uinfo->value.integer.max = 127;
587 return 0;
588 }
589
sscape_midi_get(struct snd_kcontrol * kctl,struct snd_ctl_elem_value * uctl)590 static int sscape_midi_get(struct snd_kcontrol *kctl,
591 struct snd_ctl_elem_value *uctl)
592 {
593 struct snd_wss *chip = snd_kcontrol_chip(kctl);
594 struct snd_card *card = chip->card;
595 register struct soundscape *s = get_card_soundscape(card);
596 unsigned long flags;
597
598 spin_lock_irqsave(&s->lock, flags);
599 uctl->value.integer.value[0] = s->midi_vol;
600 spin_unlock_irqrestore(&s->lock, flags);
601 return 0;
602 }
603
sscape_midi_put(struct snd_kcontrol * kctl,struct snd_ctl_elem_value * uctl)604 static int sscape_midi_put(struct snd_kcontrol *kctl,
605 struct snd_ctl_elem_value *uctl)
606 {
607 struct snd_wss *chip = snd_kcontrol_chip(kctl);
608 struct snd_card *card = chip->card;
609 struct soundscape *s = get_card_soundscape(card);
610 unsigned long flags;
611 int change;
612 unsigned char new_val;
613
614 spin_lock_irqsave(&s->lock, flags);
615
616 new_val = uctl->value.integer.value[0] & 127;
617 /*
618 * We need to put the board into HOST mode before we
619 * can send any volume-changing HOST commands ...
620 */
621 set_host_mode_unsafe(s->io_base);
622
623 /*
624 * To successfully change the MIDI volume setting, you seem to
625 * have to write a volume command, write the new volume value,
626 * and then perform another volume-related command. Perhaps the
627 * first command is an "open" and the second command is a "close"?
628 */
629 if (s->midi_vol == new_val) {
630 change = 0;
631 goto __skip_change;
632 }
633 change = host_write_ctrl_unsafe(s->io_base, CMD_SET_MIDI_VOL, 100)
634 && host_write_ctrl_unsafe(s->io_base, new_val, 100)
635 && host_write_ctrl_unsafe(s->io_base, CMD_XXX_MIDI_VOL, 100)
636 && host_write_ctrl_unsafe(s->io_base, new_val, 100);
637 s->midi_vol = new_val;
638 __skip_change:
639
640 /*
641 * Take the board out of HOST mode and back into MIDI mode ...
642 */
643 set_midi_mode_unsafe(s->io_base);
644
645 spin_unlock_irqrestore(&s->lock, flags);
646 return change;
647 }
648
649 static const struct snd_kcontrol_new midi_mixer_ctl = {
650 .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
651 .name = "MIDI",
652 .info = sscape_midi_info,
653 .get = sscape_midi_get,
654 .put = sscape_midi_put
655 };
656
657 /*
658 * The SoundScape can use two IRQs from a possible set of four.
659 * These IRQs are encoded as bit patterns so that they can be
660 * written to the control registers.
661 */
get_irq_config(int sscape_type,int irq)662 static unsigned get_irq_config(int sscape_type, int irq)
663 {
664 static const int valid_irq[] = { 9, 5, 7, 10 };
665 static const int old_irq[] = { 9, 7, 5, 15 };
666 unsigned cfg;
667
668 if (sscape_type == MEDIA_FX) {
669 for (cfg = 0; cfg < ARRAY_SIZE(old_irq); ++cfg)
670 if (irq == old_irq[cfg])
671 return cfg;
672 } else {
673 for (cfg = 0; cfg < ARRAY_SIZE(valid_irq); ++cfg)
674 if (irq == valid_irq[cfg])
675 return cfg;
676 }
677
678 return INVALID_IRQ;
679 }
680
681 /*
682 * Perform certain arcane port-checks to see whether there
683 * is a SoundScape board lurking behind the given ports.
684 */
detect_sscape(struct soundscape * s,long wss_io)685 static int detect_sscape(struct soundscape *s, long wss_io)
686 {
687 unsigned long flags;
688 unsigned d;
689 int retval = 0;
690
691 spin_lock_irqsave(&s->lock, flags);
692
693 /*
694 * The following code is lifted from the original OSS driver,
695 * and as I don't have a datasheet I cannot really comment
696 * on what it is doing...
697 */
698 if ((inb(HOST_CTRL_IO(s->io_base)) & 0x78) != 0)
699 goto _done;
700
701 d = inb(ODIE_ADDR_IO(s->io_base)) & 0xf0;
702 if ((d & 0x80) != 0)
703 goto _done;
704
705 if (d == 0)
706 s->ic_type = IC_ODIE;
707 else if ((d & 0x60) != 0)
708 s->ic_type = IC_OPUS;
709 else
710 goto _done;
711
712 outb(0xfa, ODIE_ADDR_IO(s->io_base));
713 if ((inb(ODIE_ADDR_IO(s->io_base)) & 0x9f) != 0x0a)
714 goto _done;
715
716 outb(0xfe, ODIE_ADDR_IO(s->io_base));
717 if ((inb(ODIE_ADDR_IO(s->io_base)) & 0x9f) != 0x0e)
718 goto _done;
719
720 outb(0xfe, ODIE_ADDR_IO(s->io_base));
721 d = inb(ODIE_DATA_IO(s->io_base));
722 if (s->type != SSCAPE_VIVO && (d & 0x9f) != 0x0e)
723 goto _done;
724
725 if (s->ic_type == IC_OPUS)
726 activate_ad1845_unsafe(s->io_base);
727
728 if (s->type == SSCAPE_VIVO)
729 wss_io += 4;
730
731 d = sscape_read_unsafe(s->io_base, GA_HMCTL_REG);
732 sscape_write_unsafe(s->io_base, GA_HMCTL_REG, d | 0xc0);
733
734 /* wait for WSS codec */
735 for (d = 0; d < 500; d++) {
736 if ((inb(wss_io) & 0x80) == 0)
737 break;
738 spin_unlock_irqrestore(&s->lock, flags);
739 msleep(1);
740 spin_lock_irqsave(&s->lock, flags);
741 }
742
743 if ((inb(wss_io) & 0x80) != 0)
744 goto _done;
745
746 if (inb(wss_io + 2) == 0xff)
747 goto _done;
748
749 d = sscape_read_unsafe(s->io_base, GA_HMCTL_REG) & 0x3f;
750 sscape_write_unsafe(s->io_base, GA_HMCTL_REG, d);
751
752 if ((inb(wss_io) & 0x80) != 0)
753 s->type = MEDIA_FX;
754
755 d = sscape_read_unsafe(s->io_base, GA_HMCTL_REG);
756 sscape_write_unsafe(s->io_base, GA_HMCTL_REG, d | 0xc0);
757 /* wait for WSS codec */
758 for (d = 0; d < 500; d++) {
759 if ((inb(wss_io) & 0x80) == 0)
760 break;
761 spin_unlock_irqrestore(&s->lock, flags);
762 msleep(1);
763 spin_lock_irqsave(&s->lock, flags);
764 }
765
766 /*
767 * SoundScape successfully detected!
768 */
769 retval = 1;
770
771 _done:
772 spin_unlock_irqrestore(&s->lock, flags);
773 return retval;
774 }
775
776 /*
777 * ALSA callback function, called when attempting to open the MIDI device.
778 * Check that the MIDI firmware has been loaded, because we don't want
779 * to crash the machine. Also check that someone isn't using the hardware
780 * IOCTL device.
781 */
mpu401_open(struct snd_mpu401 * mpu)782 static int mpu401_open(struct snd_mpu401 *mpu)
783 {
784 if (!verify_mpu401(mpu)) {
785 dev_err(mpu->rmidi->card->dev,
786 "sscape: MIDI disabled, please load firmware\n");
787 return -ENODEV;
788 }
789
790 return 0;
791 }
792
793 /*
794 * Initialise an MPU-401 subdevice for MIDI support on the SoundScape.
795 */
create_mpu401(struct snd_card * card,int devnum,unsigned long port,int irq)796 static int create_mpu401(struct snd_card *card, int devnum,
797 unsigned long port, int irq)
798 {
799 struct soundscape *sscape = get_card_soundscape(card);
800 struct snd_rawmidi *rawmidi;
801 int err;
802
803 err = snd_mpu401_uart_new(card, devnum, MPU401_HW_MPU401, port,
804 MPU401_INFO_INTEGRATED, irq, &rawmidi);
805 if (err == 0) {
806 struct snd_mpu401 *mpu = rawmidi->private_data;
807 mpu->open_input = mpu401_open;
808 mpu->open_output = mpu401_open;
809 mpu->private_data = sscape;
810
811 initialise_mpu401(mpu);
812 }
813
814 return err;
815 }
816
817
818 /*
819 * Create an AD1845 PCM subdevice on the SoundScape. The AD1845
820 * is very much like a CS4231, with a few extra bits. We will
821 * try to support at least some of the extra bits by overriding
822 * some of the CS4231 callback.
823 */
create_ad1845(struct snd_card * card,unsigned port,int irq,int dma1,int dma2)824 static int create_ad1845(struct snd_card *card, unsigned port,
825 int irq, int dma1, int dma2)
826 {
827 register struct soundscape *sscape = get_card_soundscape(card);
828 struct snd_wss *chip;
829 int err;
830 int codec_type = WSS_HW_DETECT;
831
832 switch (sscape->type) {
833 case MEDIA_FX:
834 case SSCAPE:
835 /*
836 * There are some freak examples of early Soundscape cards
837 * with CS4231 instead of AD1848/CS4248. Unfortunately, the
838 * CS4231 works only in CS4248 compatibility mode on
839 * these cards so force it.
840 */
841 if (sscape->ic_type != IC_OPUS)
842 codec_type = WSS_HW_AD1848;
843 break;
844
845 case SSCAPE_VIVO:
846 port += 4;
847 break;
848 default:
849 break;
850 }
851
852 err = snd_wss_create(card, port, -1, irq, dma1, dma2,
853 codec_type, WSS_HWSHARE_DMA1, &chip);
854 if (!err) {
855 unsigned long flags;
856
857 if (sscape->type != SSCAPE_VIVO) {
858 /*
859 * The input clock frequency on the SoundScape must
860 * be 14.31818 MHz, because we must set this register
861 * to get the playback to sound correct ...
862 */
863 snd_wss_mce_up(chip);
864 spin_lock_irqsave(&chip->reg_lock, flags);
865 snd_wss_out(chip, AD1845_CLOCK, 0x20);
866 spin_unlock_irqrestore(&chip->reg_lock, flags);
867 snd_wss_mce_down(chip);
868
869 }
870
871 err = snd_wss_pcm(chip, 0);
872 if (err < 0) {
873 dev_err(card->dev,
874 "sscape: No PCM device for AD1845 chip\n");
875 goto _error;
876 }
877
878 err = snd_wss_mixer(chip);
879 if (err < 0) {
880 dev_err(card->dev,
881 "sscape: No mixer device for AD1845 chip\n");
882 goto _error;
883 }
884 if (chip->hardware != WSS_HW_AD1848) {
885 err = snd_wss_timer(chip, 0);
886 if (err < 0) {
887 dev_err(card->dev,
888 "sscape: No timer device for AD1845 chip\n");
889 goto _error;
890 }
891 }
892
893 if (sscape->type != SSCAPE_VIVO) {
894 err = snd_ctl_add(card,
895 snd_ctl_new1(&midi_mixer_ctl, chip));
896 if (err < 0) {
897 dev_err(card->dev,
898 "sscape: Could not create MIDI mixer control\n");
899 goto _error;
900 }
901 }
902
903 sscape->chip = chip;
904 }
905
906 _error:
907 return err;
908 }
909
910
911 /*
912 * Create an ALSA soundcard entry for the SoundScape, using
913 * the given list of port, IRQ and DMA resources.
914 */
create_sscape(int dev,struct snd_card * card)915 static int create_sscape(int dev, struct snd_card *card)
916 {
917 struct soundscape *sscape = get_card_soundscape(card);
918 unsigned dma_cfg;
919 unsigned irq_cfg;
920 unsigned mpu_irq_cfg;
921 struct resource *io_res;
922 struct resource *wss_res;
923 unsigned long flags;
924 int err;
925 int val;
926 const char *name;
927
928 /*
929 * Grab IO ports that we will need to probe so that we
930 * can detect and control this hardware ...
931 */
932 io_res = devm_request_region(card->dev, port[dev], 8, "SoundScape");
933 if (!io_res) {
934 dev_err(card->dev,
935 "sscape: can't grab port 0x%lx\n", port[dev]);
936 return -EBUSY;
937 }
938 wss_res = NULL;
939 if (sscape->type == SSCAPE_VIVO) {
940 wss_res = devm_request_region(card->dev, wss_port[dev], 4,
941 "SoundScape");
942 if (!wss_res) {
943 dev_err(card->dev, "sscape: can't grab port 0x%lx\n",
944 wss_port[dev]);
945 return -EBUSY;
946 }
947 }
948
949 /*
950 * Grab one DMA channel ...
951 */
952 err = snd_devm_request_dma(card->dev, dma[dev], "SoundScape");
953 if (err < 0) {
954 dev_err(card->dev, "sscape: can't grab DMA %d\n", dma[dev]);
955 return err;
956 }
957
958 spin_lock_init(&sscape->lock);
959 sscape->io_res = io_res;
960 sscape->wss_res = wss_res;
961 sscape->io_base = port[dev];
962
963 if (!detect_sscape(sscape, wss_port[dev])) {
964 dev_err(card->dev, "sscape: hardware not detected at 0x%x\n",
965 sscape->io_base);
966 return -ENODEV;
967 }
968
969 switch (sscape->type) {
970 case MEDIA_FX:
971 name = "MediaFX/SoundFX";
972 break;
973 case SSCAPE:
974 name = "Soundscape";
975 break;
976 case SSCAPE_PNP:
977 name = "Soundscape PnP";
978 break;
979 case SSCAPE_VIVO:
980 name = "Soundscape VIVO";
981 break;
982 default:
983 name = "unknown Soundscape";
984 break;
985 }
986
987 dev_info(card->dev, "sscape: %s card detected at 0x%x, using IRQ %d, DMA %d\n",
988 name, sscape->io_base, irq[dev], dma[dev]);
989
990 /*
991 * Check that the user didn't pass us garbage data ...
992 */
993 irq_cfg = get_irq_config(sscape->type, irq[dev]);
994 if (irq_cfg == INVALID_IRQ) {
995 dev_err(card->dev, "sscape: Invalid IRQ %d\n", irq[dev]);
996 return -ENXIO;
997 }
998
999 mpu_irq_cfg = get_irq_config(sscape->type, mpu_irq[dev]);
1000 if (mpu_irq_cfg == INVALID_IRQ) {
1001 dev_err(card->dev, "sscape: Invalid IRQ %d\n", mpu_irq[dev]);
1002 return -ENXIO;
1003 }
1004
1005 /*
1006 * Tell the on-board devices where their resources are (I think -
1007 * I can't be sure without a datasheet ... So many magic values!)
1008 */
1009 spin_lock_irqsave(&sscape->lock, flags);
1010
1011 sscape_write_unsafe(sscape->io_base, GA_SMCFGA_REG, 0x2e);
1012 sscape_write_unsafe(sscape->io_base, GA_SMCFGB_REG, 0x00);
1013
1014 /*
1015 * Enable and configure the DMA channels ...
1016 */
1017 sscape_write_unsafe(sscape->io_base, GA_DMACFG_REG, 0x50);
1018 dma_cfg = (sscape->ic_type == IC_OPUS ? 0x40 : 0x70);
1019 sscape_write_unsafe(sscape->io_base, GA_DMAA_REG, dma_cfg);
1020 sscape_write_unsafe(sscape->io_base, GA_DMAB_REG, 0x20);
1021
1022 mpu_irq_cfg |= mpu_irq_cfg << 2;
1023 val = sscape_read_unsafe(sscape->io_base, GA_HMCTL_REG) & 0xF7;
1024 if (joystick[dev])
1025 val |= 8;
1026 sscape_write_unsafe(sscape->io_base, GA_HMCTL_REG, val | 0x10);
1027 sscape_write_unsafe(sscape->io_base, GA_INTCFG_REG, 0xf0 | mpu_irq_cfg);
1028 sscape_write_unsafe(sscape->io_base,
1029 GA_CDCFG_REG, 0x09 | DMA_8BIT
1030 | (dma[dev] << 4) | (irq_cfg << 1));
1031 /*
1032 * Enable the master IRQ ...
1033 */
1034 sscape_write_unsafe(sscape->io_base, GA_INTENA_REG, 0x80);
1035
1036 spin_unlock_irqrestore(&sscape->lock, flags);
1037
1038 /*
1039 * We have now enabled the codec chip, and so we should
1040 * detect the AD1845 device ...
1041 */
1042 err = create_ad1845(card, wss_port[dev], irq[dev],
1043 dma[dev], dma2[dev]);
1044 if (err < 0) {
1045 dev_err(card->dev,
1046 "sscape: No AD1845 device at 0x%lx, IRQ %d\n",
1047 wss_port[dev], irq[dev]);
1048 return err;
1049 }
1050 strcpy(card->driver, "SoundScape");
1051 strcpy(card->shortname, name);
1052 snprintf(card->longname, sizeof(card->longname),
1053 "%s at 0x%lx, IRQ %d, DMA1 %d, DMA2 %d\n",
1054 name, sscape->chip->port, sscape->chip->irq,
1055 sscape->chip->dma1, sscape->chip->dma2);
1056
1057 #define MIDI_DEVNUM 0
1058 if (sscape->type != SSCAPE_VIVO) {
1059 err = sscape_upload_bootblock(card);
1060 if (err >= 0)
1061 err = sscape_upload_microcode(card, err);
1062
1063 if (err == 0) {
1064 err = create_mpu401(card, MIDI_DEVNUM, port[dev],
1065 mpu_irq[dev]);
1066 if (err < 0) {
1067 dev_err(card->dev,
1068 "sscape: Failed to create MPU-401 device at 0x%lx\n",
1069 port[dev]);
1070 return err;
1071 }
1072
1073 /*
1074 * Initialize mixer
1075 */
1076 spin_lock_irqsave(&sscape->lock, flags);
1077 sscape->midi_vol = 0;
1078 host_write_ctrl_unsafe(sscape->io_base,
1079 CMD_SET_MIDI_VOL, 100);
1080 host_write_ctrl_unsafe(sscape->io_base,
1081 sscape->midi_vol, 100);
1082 host_write_ctrl_unsafe(sscape->io_base,
1083 CMD_XXX_MIDI_VOL, 100);
1084 host_write_ctrl_unsafe(sscape->io_base,
1085 sscape->midi_vol, 100);
1086 host_write_ctrl_unsafe(sscape->io_base,
1087 CMD_SET_EXTMIDI, 100);
1088 host_write_ctrl_unsafe(sscape->io_base,
1089 0, 100);
1090 host_write_ctrl_unsafe(sscape->io_base, CMD_ACK, 100);
1091
1092 set_midi_mode_unsafe(sscape->io_base);
1093 spin_unlock_irqrestore(&sscape->lock, flags);
1094 }
1095 }
1096
1097 return 0;
1098 }
1099
1100
snd_sscape_match(struct device * pdev,unsigned int i)1101 static int snd_sscape_match(struct device *pdev, unsigned int i)
1102 {
1103 /*
1104 * Make sure we were given ALL of the other parameters.
1105 */
1106 if (port[i] == SNDRV_AUTO_PORT)
1107 return 0;
1108
1109 if (irq[i] == SNDRV_AUTO_IRQ ||
1110 mpu_irq[i] == SNDRV_AUTO_IRQ ||
1111 dma[i] == SNDRV_AUTO_DMA) {
1112 dev_info(pdev,
1113 "sscape: insufficient parameters, need IO, IRQ, MPU-IRQ and DMA\n");
1114 return 0;
1115 }
1116
1117 return 1;
1118 }
1119
snd_sscape_probe(struct device * pdev,unsigned int dev)1120 static int snd_sscape_probe(struct device *pdev, unsigned int dev)
1121 {
1122 struct snd_card *card;
1123 struct soundscape *sscape;
1124 int ret;
1125
1126 ret = snd_devm_card_new(pdev, index[dev], id[dev], THIS_MODULE,
1127 sizeof(struct soundscape), &card);
1128 if (ret < 0)
1129 return ret;
1130
1131 sscape = get_card_soundscape(card);
1132 sscape->dev = pdev;
1133 sscape->type = SSCAPE;
1134
1135 dma[dev] &= 0x03;
1136
1137 ret = create_sscape(dev, card);
1138 if (ret < 0)
1139 return ret;
1140
1141 ret = snd_card_register(card);
1142 if (ret < 0) {
1143 dev_err(pdev, "sscape: Failed to register sound card\n");
1144 return ret;
1145 }
1146 dev_set_drvdata(pdev, card);
1147 return 0;
1148 }
1149
1150 #define DEV_NAME "sscape"
1151
1152 static struct isa_driver snd_sscape_driver = {
1153 .match = snd_sscape_match,
1154 .probe = snd_sscape_probe,
1155 /* FIXME: suspend/resume */
1156 .driver = {
1157 .name = DEV_NAME
1158 },
1159 };
1160
1161 #ifdef CONFIG_PNP
get_next_autoindex(int i)1162 static inline int get_next_autoindex(int i)
1163 {
1164 while (i < SNDRV_CARDS && port[i] != SNDRV_AUTO_PORT)
1165 ++i;
1166 return i;
1167 }
1168
1169
sscape_pnp_detect(struct pnp_card_link * pcard,const struct pnp_card_device_id * pid)1170 static int sscape_pnp_detect(struct pnp_card_link *pcard,
1171 const struct pnp_card_device_id *pid)
1172 {
1173 static int idx = 0;
1174 struct pnp_dev *dev;
1175 struct snd_card *card;
1176 struct soundscape *sscape;
1177 int ret;
1178
1179 /*
1180 * Allow this function to fail *quietly* if all the ISA PnP
1181 * devices were configured using module parameters instead.
1182 */
1183 idx = get_next_autoindex(idx);
1184 if (idx >= SNDRV_CARDS)
1185 return -ENOSPC;
1186
1187 /*
1188 * Check that we still have room for another sound card ...
1189 */
1190 dev = pnp_request_card_device(pcard, pid->devs[0].id, NULL);
1191 if (!dev)
1192 return -ENODEV;
1193
1194 if (!pnp_is_active(dev)) {
1195 if (pnp_activate_dev(dev) < 0) {
1196 dev_info(&dev->dev, "sscape: device is inactive\n");
1197 return -EBUSY;
1198 }
1199 }
1200
1201 /*
1202 * Create a new ALSA sound card entry, in anticipation
1203 * of detecting our hardware ...
1204 */
1205 ret = snd_devm_card_new(&pcard->card->dev,
1206 index[idx], id[idx], THIS_MODULE,
1207 sizeof(struct soundscape), &card);
1208 if (ret < 0)
1209 return ret;
1210
1211 sscape = get_card_soundscape(card);
1212 sscape->dev = card->dev;
1213
1214 /*
1215 * Identify card model ...
1216 */
1217 if (!strncmp("ENS4081", pid->id, 7))
1218 sscape->type = SSCAPE_VIVO;
1219 else
1220 sscape->type = SSCAPE_PNP;
1221
1222 /*
1223 * Read the correct parameters off the ISA PnP bus ...
1224 */
1225 port[idx] = pnp_port_start(dev, 0);
1226 irq[idx] = pnp_irq(dev, 0);
1227 mpu_irq[idx] = pnp_irq(dev, 1);
1228 dma[idx] = pnp_dma(dev, 0) & 0x03;
1229 if (sscape->type == SSCAPE_PNP) {
1230 dma2[idx] = dma[idx];
1231 wss_port[idx] = CODEC_IO(port[idx]);
1232 } else {
1233 wss_port[idx] = pnp_port_start(dev, 1);
1234 dma2[idx] = pnp_dma(dev, 1);
1235 }
1236
1237 ret = create_sscape(idx, card);
1238 if (ret < 0)
1239 return ret;
1240
1241 ret = snd_card_register(card);
1242 if (ret < 0) {
1243 dev_err(card->dev, "sscape: Failed to register sound card\n");
1244 return ret;
1245 }
1246
1247 pnp_set_card_drvdata(pcard, card);
1248 ++idx;
1249 return 0;
1250 }
1251
1252 static struct pnp_card_driver sscape_pnpc_driver = {
1253 .flags = PNP_DRIVER_RES_DO_NOT_CHANGE,
1254 .name = "sscape",
1255 .id_table = sscape_pnpids,
1256 .probe = sscape_pnp_detect,
1257 };
1258
1259 #endif /* CONFIG_PNP */
1260
sscape_init(void)1261 static int __init sscape_init(void)
1262 {
1263 int err;
1264
1265 err = isa_register_driver(&snd_sscape_driver, SNDRV_CARDS);
1266 #ifdef CONFIG_PNP
1267 if (!err)
1268 isa_registered = 1;
1269
1270 err = pnp_register_card_driver(&sscape_pnpc_driver);
1271 if (!err)
1272 pnp_registered = 1;
1273
1274 if (isa_registered)
1275 err = 0;
1276 #endif
1277 return err;
1278 }
1279
sscape_exit(void)1280 static void __exit sscape_exit(void)
1281 {
1282 #ifdef CONFIG_PNP
1283 if (pnp_registered)
1284 pnp_unregister_card_driver(&sscape_pnpc_driver);
1285 if (isa_registered)
1286 #endif
1287 isa_unregister_driver(&snd_sscape_driver);
1288 }
1289
1290 module_init(sscape_init);
1291 module_exit(sscape_exit);
1292