1 # SPDX-License-Identifier: GPL-2.0-only 2 # 3 # Freescale device configuration 4 # 5 6 config NET_VENDOR_FREESCALE 7 bool "Freescale devices" 8 default y 9 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ 10 M523x || M527x || M5272 || M528x || M520x || M532x || \ 11 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \ 12 ARCH_LAYERSCAPE || ARCH_S32 || COMPILE_TEST 13 help 14 If you have a network (Ethernet) card belonging to this class, say Y. 15 16 Note that the answer to this question doesn't directly affect the 17 kernel: saying N will just cause the configurator to skip all 18 the questions about Freescale devices. If you say Y, you will be 19 asked for your specific card in the following questions. 20 21 if NET_VENDOR_FREESCALE 22 23 config FEC 24 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 25 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ 26 ARCH_MXC || ARCH_S32 || SOC_IMX28 || COMPILE_TEST) 27 default ARCH_MXC || SOC_IMX28 if ARM 28 depends on PTP_1588_CLOCK_OPTIONAL 29 select CRC32 30 select PHYLIB 31 select PAGE_POOL 32 imply PAGE_POOL_STATS 33 imply NET_SELFTESTS 34 help 35 Say Y here if you want to use the built-in 10/100 Fast ethernet 36 controller on some Motorola ColdFire and Freescale i.MX/S32 processors. 37 38 config FEC_MPC52xx 39 tristate "FEC MPC52xx driver" 40 depends on PPC_MPC52xx && PPC_BESTCOMM 41 select CRC32 42 select PHYLIB 43 select PPC_BESTCOMM_FEC 44 help 45 This option enables support for the MPC5200's on-chip 46 Fast Ethernet Controller 47 If compiled as module, it will be called fec_mpc52xx. 48 49 config FEC_MPC52xx_MDIO 50 bool "FEC MPC52xx MDIO bus driver" 51 depends on FEC_MPC52xx 52 default y 53 help 54 The MPC5200's FEC can connect to the Ethernet either with 55 an external MII PHY chip or 10 Mbps 7-wire interface 56 (Motorola? industry standard). 57 If your board uses an external PHY connected to FEC, enable this. 58 If not sure, enable. 59 If compiled as module, it will be called fec_mpc52xx_phy. 60 61 source "drivers/net/ethernet/freescale/fs_enet/Kconfig" 62 source "drivers/net/ethernet/freescale/fman/Kconfig" 63 64 config FSL_PQ_MDIO 65 tristate "Freescale PQ MDIO" 66 select PHYLIB 67 help 68 This driver supports the MDIO bus used by the gianfar and UCC drivers. 69 70 config FSL_XGMAC_MDIO 71 tristate "Freescale XGMAC MDIO" 72 select PHYLIB 73 depends on OF 74 select MDIO_DEVRES 75 select OF_MDIO 76 help 77 This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and 78 on the FMan mEMAC (which supports both Clauses 22 and 45) 79 80 config UCC_GETH 81 tristate "Freescale QE Gigabit Ethernet" 82 depends on QUICC_ENGINE && PPC32 83 select FSL_PQ_MDIO 84 select PHYLIB 85 select FIXED_PHY 86 help 87 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 88 which is available on some Freescale SOCs. 89 90 config UGETH_TX_ON_DEMAND 91 bool "Transmit on Demand support" 92 depends on UCC_GETH 93 94 config GIANFAR 95 tristate "Gianfar Ethernet" 96 depends on HAS_DMA 97 select FSL_PQ_MDIO 98 select PHYLIB 99 select FIXED_PHY 100 select CRC32 101 help 102 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 103 and MPC86xx family of chips, the eTSEC on LS1021A and the FEC 104 on the 8540. 105 106 source "drivers/net/ethernet/freescale/dpaa/Kconfig" 107 source "drivers/net/ethernet/freescale/dpaa2/Kconfig" 108 source "drivers/net/ethernet/freescale/enetc/Kconfig" 109 110 endif # NET_VENDOR_FREESCALE 111