1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2021 STMicroelectronics
4 * Author: Alain Volmat <avolmat@me.com>
5 */
6/dts-v1/;
7#include "stih418.dtsi"
8#include <dt-bindings/gpio/gpio.h>
9/ {
10	model = "STiH418 B2264";
11	compatible = "st,stih418-b2264", "st,stih418";
12
13	chosen {
14		stdout-path = &sbc_serial0;
15	};
16
17	memory@40000000 {
18		device_type = "memory";
19		reg = <0x40000000 0xc0000000>;
20	};
21
22	cpus {
23		cpu@0 {
24			operating-points-v2 = <&cpu_opp_table>;
25			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
26			cpu-release-addr = <0x94100b8>;
27		};
28		cpu@1 {
29			operating-points-v2 = <&cpu_opp_table>;
30			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
31			cpu-release-addr = <0x94100b8>;
32		};
33		cpu@2 {
34			operating-points-v2 = <&cpu_opp_table>;
35			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
36			cpu-release-addr = <0x94100b8>;
37		};
38		cpu@3 {
39			operating-points-v2 = <&cpu_opp_table>;
40			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
41			cpu-release-addr = <0x94100b8>;
42		};
43	};
44
45	cpu_opp_table: opp-table {
46		compatible = "operating-points-v2";
47		opp-shared;
48
49		opp00 {
50			opp-hz = /bits/ 64 <300000000>;
51			opp-microvolt = <784000>;
52		};
53		opp01 {
54			opp-hz = /bits/ 64 <500000000>;
55			opp-microvolt = <784000>;
56		};
57		opp02 {
58			opp-hz = /bits/ 64 <800000000>;
59			opp-microvolt = <784000>;
60		};
61		opp03 {
62			opp-hz = /bits/ 64 <1200000000>;
63			opp-microvolt = <784000>;
64		};
65		opp04 {
66			opp-hz = /bits/ 64 <1500000000>;
67			opp-microvolt = <784000>;
68		};
69	};
70
71	aliases {
72		serial0 = &sbc_serial0;
73		ethernet0 = &ethernet0;
74	};
75
76	leds {
77		compatible = "gpio-leds";
78		led-green {
79			gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
80			default-state = "off";
81		};
82	};
83
84	soc {
85		pin-controller-sbc@961f080 {
86			gmac1 {
87				rgmii1-0 {
88					st,pins {
89						rxd0 = <&pio1 4 ALT1 IN DE_IO 300 CLK_A>;
90						rxd1 = <&pio1 5 ALT1 IN DE_IO 300 CLK_A>;
91						rxd2 = <&pio1 6 ALT1 IN DE_IO 300 CLK_A>;
92						rxd3 = <&pio1 7 ALT1 IN DE_IO 300 CLK_A>;
93						rxdv = <&pio2 0 ALT1 IN DE_IO 300 CLK_A>;
94					};
95				};
96			};
97		};
98
99	};
100};
101
102&ehci0 {
103	status = "okay";
104};
105
106&ethernet0 {
107	phy-mode = "rgmii";
108	pinctrl-0 = <&pinctrl_rgmii1 &pinctrl_rgmii1_mdio_1>;
109	st,tx-retime-src = "clkgen";
110
111	snps,reset-gpio = <&pio0 7 0>;
112	snps,reset-active-low;
113	snps,reset-delays-us = <0 10000 1000000>;
114
115	status = "okay";
116};
117
118&miphy28lp_phy {
119	phy_port0: port@9b22000 {
120		st,sata-gen = <2>; /* SATA GEN3 */
121		st,osc-rdy;
122	};
123};
124
125&mmc0 {
126	status = "okay";
127};
128
129&ohci1 {
130	status = "okay";
131};
132
133&pwm1 {
134	status = "okay";
135};
136
137&sata0 {
138	status = "okay";
139};
140
141&sbc_serial0 {
142	status = "okay";
143};
144
145&spifsm {
146	status = "okay";
147};
148
149&st_dwc3 {
150	status = "okay";
151};
152