1// SPDX-License-Identifier: BSD-3-Clause
2#include <dt-bindings/iio/qcom,spmi-vadc.h>
3#include <dt-bindings/input/linux-event-codes.h>
4#include <dt-bindings/interrupt-controller/irq.h>
5#include <dt-bindings/spmi/spmi.h>
6
7/ {
8	thermal-zones {
9		pm8226-thermal {
10			polling-delay-passive = <100>;
11			polling-delay = <0>;
12			thermal-sensors = <&pm8226_temp>;
13
14			trips {
15				trip0 {
16					temperature = <105000>;
17					hysteresis = <2000>;
18					type = "passive";
19				};
20
21				trip1 {
22					temperature = <125000>;
23					hysteresis = <2000>;
24					type = "hot";
25				};
26
27				crit {
28					temperature = <145000>;
29					hysteresis = <2000>;
30					type = "critical";
31				};
32			};
33		};
34	};
35};
36
37&spmi_bus {
38	pm8226_0: pm8226@0 {
39		compatible = "qcom,pm8226", "qcom,spmi-pmic";
40		reg = <0x0 SPMI_USID>;
41		#address-cells = <1>;
42		#size-cells = <0>;
43
44		pon@800 {
45			compatible = "qcom,pm8916-pon";
46			reg = <0x800>;
47
48			pwrkey {
49				compatible = "qcom,pm8941-pwrkey";
50				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
51				debounce = <15625>;
52				bias-pull-up;
53				linux,code = <KEY_POWER>;
54			};
55
56			pm8226_resin: resin {
57				compatible = "qcom,pm8941-resin";
58				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
59				debounce = <15625>;
60				bias-pull-up;
61				status = "disabled";
62			};
63		};
64
65		smbb: charger@1000 {
66			compatible = "qcom,pm8226-charger";
67			reg = <0x1000>;
68			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
69				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
70				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
71				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
72				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
73				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
74				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
75				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
76			interrupt-names = "chg-done",
77					  "chg-fast",
78					  "chg-trkl",
79					  "bat-temp-ok",
80					  "bat-present",
81					  "chg-gone",
82					  "usb-valid",
83					  "dc-valid";
84
85			status = "disabled";
86
87			chg_otg: otg-vbus { };
88		};
89
90		pm8226_temp: temp-alarm@2400 {
91			compatible = "qcom,spmi-temp-alarm";
92			reg = <0x2400>;
93			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
94			io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
95			io-channel-names = "thermal";
96			#thermal-sensor-cells = <0>;
97		};
98
99		pm8226_vadc: adc@3100 {
100			compatible = "qcom,spmi-vadc";
101			reg = <0x3100>;
102			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
103			#address-cells = <1>;
104			#size-cells = <0>;
105			#io-channel-cells = <1>;
106
107			channel@7 {
108				reg = <VADC_VSYS>;
109				qcom,pre-scaling = <1 3>;
110				label = "vph_pwr";
111			};
112			channel@8 {
113				reg = <VADC_DIE_TEMP>;
114				label = "die_temp";
115			};
116			channel@9 {
117				reg = <VADC_REF_625MV>;
118				label = "ref_625mv";
119			};
120			channel@a {
121				reg = <VADC_REF_1250MV>;
122				label = "ref_1250mv";
123			};
124			channel@e {
125				reg = <VADC_GND_REF>;
126			};
127			channel@f {
128				reg = <VADC_VDD_VADC>;
129			};
130		};
131
132		pm8226_iadc: adc@3600 {
133			compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
134			reg = <0x3600>;
135			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
136		};
137
138		rtc@6000 {
139			compatible = "qcom,pm8941-rtc";
140			reg = <0x6000>, <0x6100>;
141			reg-names = "rtc", "alarm";
142			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
143		};
144
145		pm8226_mpps: mpps@a000 {
146			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
147			reg = <0xa000>;
148			gpio-controller;
149			#gpio-cells = <2>;
150			gpio-ranges = <&pm8226_mpps 0 0 8>;
151			interrupt-controller;
152			#interrupt-cells = <2>;
153		};
154
155		pm8226_gpios: gpio@c000 {
156			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
157			reg = <0xc000>;
158			gpio-controller;
159			#gpio-cells = <2>;
160			gpio-ranges = <&pm8226_gpios 0 0 8>;
161			interrupt-controller;
162			#interrupt-cells = <2>;
163		};
164	};
165
166	pm8226_1: pm8226@1 {
167		compatible = "qcom,pm8226", "qcom,spmi-pmic";
168		reg = <0x1 SPMI_USID>;
169		#address-cells = <1>;
170		#size-cells = <0>;
171
172		pm8226_spmi_regulators: regulators {
173			compatible = "qcom,pm8226-regulators";
174		};
175
176		pm8226_vib: vibrator@c000 {
177			compatible = "qcom,pm8916-vib";
178			reg = <0xc000>;
179			status = "disabled";
180		};
181	};
182};
183