1 /* 2 * Copyright (c) 2012-2019 The Linux Foundation. All rights reserved. 3 * 4 * Permission to use, copy, modify, and/or distribute this software for 5 * any purpose with or without fee is hereby granted, provided that the 6 * above copyright notice and this permission notice appear in all 7 * copies. 8 * 9 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL 10 * WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED 11 * WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE 12 * AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL 13 * DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR 14 * PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER 15 * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR 16 * PERFORMANCE OF THIS SOFTWARE. 17 */ 18 19 /** 20 * DOC: declares vendor commands interfacing with linux kernel 21 */ 22 23 24 #ifndef _WLAN_QCA_VENDOR_H_ 25 #define _WLAN_QCA_VENDOR_H_ 26 27 /* Vendor id to be used in vendor specific command and events 28 * to user space. 29 * NOTE: The authoritative place for definition of QCA_NL80211_VENDOR_ID, 30 * vendor subcmd definitions prefixed with QCA_NL80211_VENDOR_SUBCMD, and 31 * qca_wlan_vendor_attr is open source file src/common/qca-vendor.h in 32 * git://w1.fi/srv/git/hostap.git; the values here are just a copy of that 33 */ 34 35 #define QCA_NL80211_VENDOR_ID 0x001374 36 37 /** 38 * enum qca_nl80211_vendor_subcmds: NL 80211 vendor sub command 39 * 40 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Unspecified 41 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test 42 * Sub commands 2 to 8 are not used 43 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Roaming 44 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Avoid frequency. 45 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: DFS capability 46 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass 47 * NAN Request/Response and NAN Indication messages. These messages are 48 * interpreted between the framework and the firmware component. While 49 * sending the command from userspace to the driver, payload is not 50 * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN 51 * is used when receiving vendor events in userspace from the driver. 52 * @QCA_NL80211_VENDOR_SUBCMD_STATS_EXT: Ext stats 53 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET: Link layer stats set 54 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET: Link layer stats get 55 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR: Link layer stats clear 56 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS: Link layer stats radio 57 * results 58 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS: Link layer stats interface 59 * results 60 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS: Link layer stats peer 61 * results 62 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START: Ext scan start 63 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP: Ext scan stop 64 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS: Ext scan get valid 65 * channels 66 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES: Ext scan get capability 67 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS: Ext scan get cached 68 * results 69 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE: Ext scan results 70 * available. Used when report_threshold is reached in scan cache. 71 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT: Ext scan full scan 72 * result. Used to report scan results when each probe rsp. is received, 73 * if report_events enabled in wifi_scan_cmd_params. 74 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT: Ext scan event from target. 75 * Indicates progress of scanning state-machine. 76 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND: Ext scan hotlist 77 * ap found 78 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST: Ext scan set hotlist 79 * bssid 80 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST: Ext scan reset 81 * hotlist bssid 82 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE: Ext scan significant 83 * change 84 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE: Ext scan set 85 * significant change 86 * ap found 87 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE: Ext scan reset 88 * significant change 89 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE: Ext tdls enable 90 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE: Ext tdls disable 91 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS: Ext tdls get status 92 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE: Ext tdls state 93 * @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES: Get supported features 94 * @QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI: Set scanning_mac_oui 95 * @QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG: No DFS flag 96 * @QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX: Get Concurrency Matrix 97 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Get the key mgmt offload keys 98 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: After roaming, send the 99 * roaming and auth information. 100 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_SCHED: Set OCB schedule 101 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS offload flag 102 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Get the supported features by the 103 * driver. 104 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Indicate that driver 105 * started CAC on DFS channel 106 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Indicate that driver 107 * completed the CAC check on DFS channel 108 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Indicate that the CAC 109 * check was aborted by the driver 110 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Indicate that the 111 * driver completed NOP 112 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Indicate that the 113 * driver detected radar signal on the current operating channel 114 * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO: get wlan driver information 115 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START: start wifi logger 116 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP: memory dump request 117 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: get logger feature set 118 * @QCA_NL80211_VENDOR_SUBCMD_ROAM: roam 119 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST: extscan set ssid hotlist 120 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST: 121 * extscan reset ssid hotlist 122 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND: hotlist ssid found 123 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST: hotlist ssid lost 124 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_LIST: set pno list 125 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_PASSPOINT_LIST: set passpoint list 126 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_RESET_PASSPOINT_LIST: 127 * reset passpoint list 128 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND: pno network found 129 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND: 130 * passpoint network found 131 * @QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION: set wifi config 132 * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION: get wifi config 133 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: get logging features 134 * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: get link properties 135 * @QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG: set gateway parameters 136 * @QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST: get preferred channel 137 list 138 * @QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL: channel hint 139 * @QCA_NL80211_VENDOR_SUBCMD_SETBAND: vendor setband command 140 * @QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN: venodr scan command 141 * @QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE: vendor scan complete 142 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: vendor abort scan 143 * @QCA_NL80211_VENDOR_SUBCMD_OTA_TEST: enable OTA test 144 * @QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE: set tx power by percentage 145 * @QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE_DECR_DB: reduce tx power by DB 146 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG: SAP configuration 147 * @QCA_NL80211_VENDOR_SUBCMD_TSF: TSF operations command 148 * @QCA_NL80211_VENDOR_SUBCMD_WISA: WISA mode configuration 149 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to 150 * start the P2P Listen Offload function in device and pass the listen 151 * channel, period, interval, count, number of device types, device 152 * types and vendor information elements to device driver and firmware. 153 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to 154 * indicate stop request/response of the P2P Listen Offload function in 155 * device. As an event, it indicates either the feature stopped after it 156 * was already running or feature has actually failed to start. 157 * @QCA_NL80211_VENDOR_SUBCMD_GET_STATION: send BSS Information 158 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After SAP starts 159 * beaconing, this sub command provides the driver, the frequencies on the 160 * 5 GHz to check for any radar activity. Driver selects one channel from 161 * this priority list provided through 162 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts 163 * to check for radar activity on it. If no radar activity is detected 164 * during the channel availability check period, driver internally switches 165 * to the selected frequency of operation. If the frequency is zero, driver 166 * internally selects a channel. The status of this conditional switch is 167 * indicated through an event using the same sub command through 168 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are 169 * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch 170 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Command/event used to config 171 * indication period and threshold for MAC layer counters. 172 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior 173 * in the host driver. The different TDLS configurations are defined 174 * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. 175 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Get HE related capabilities 176 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS:Set the Specific Absorption Rate 177 * (SAR) power limits. A critical regulation for FCC compliance, OEMs 178 * require methods to set SAR limits on TX power of WLAN/WWAN. 179 * enum qca_vendor_attr_sar_limits attributes are used with this command. 180 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: Vendor command used to get/set 181 * configuration of vendor ACS. 182 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the 183 * requisite information leading to a power save failure. The information 184 * carried as part of this event is represented by the 185 * enum qca_attr_chip_power_save_failure attributes. 186 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics 187 * collection. Uses attributes defined in enum qca_attr_nud_stats_set. 188 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These 189 * statistics are represented by the enum qca_attr_nud_stats_get 190 * attributes. 191 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch 192 * the BSS transition status, whether accept or reject, for a list of 193 * candidate BSSIDs provided by the userspace. This uses the vendor 194 * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and 195 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify 196 * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an 197 * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in 198 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response 199 * the driver shall specify array of 200 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and 201 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in 202 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. 203 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a 204 * specific QCA module. The trace levels are represented by 205 * enum qca_attr_trace_level attributes. 206 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement 207 * Protocol antenna limit in different modes. See enum 208 * qca_wlan_vendor_attr_brp_ant_limit_mode. 209 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan 210 * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. 211 * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) 212 * identifying the operation in success case. 213 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses 214 * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from 215 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to 216 * be stopped. 217 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the 218 * specific interface. This can be used to modify some of the low level 219 * scan parameters (off channel dwell time, home channel time) in the 220 * driver/firmware. These parameters are maintained within the host 221 * driver. 222 * This command is valid only when the interface is in the connected 223 * state. 224 * These scan parameters shall be reset by the driver/firmware once 225 * disconnected. The attributes used with this command are defined in 226 * enum qca_wlan_vendor_attr_active_tos. 227 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the 228 * driver has detected an internal failure. This event carries the 229 * information indicating the reason that triggered this detection. The 230 * attributes for this command are defined in 231 * enum qca_wlan_vendor_attr_hang. 232 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values 233 * of spectral parameters used. The spectral scan parameters are specified 234 * by enum qca_wlan_vendor_attr_spectral_scan. 235 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats 236 * for spectral scan functionality. The debug stats are specified by 237 * enum qca_wlan_vendor_attr_spectral_diag_stats. 238 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral 239 * scan system capabilities. The capabilities are specified 240 * by enum qca_wlan_vendor_attr_spectral_cap. 241 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current 242 * status of spectral scan. The status values are specified 243 * by enum qca_wlan_vendor_attr_spectral_scan_status. 244 * @QCA_NL80211_VENDOR_SUBCMD_HTT_STATS: Request the firmware 245 * DP stats for a particualr stats type for response evnet 246 * it carries the stats data sent from the FW 247 * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative 248 * RF Operating Parameter (RROP) information. The attributes for this 249 * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is 250 * intended for use by external Auto Channel Selection applications. 251 * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate 252 * (SAR) power limits. This is a companion to the command 253 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the 254 * settings currently in use. The attributes returned by this command are 255 * defined by enum qca_vendor_attr_sar_limits. 256 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behaviour of 257 * the WLAN hardware MAC's associated with each WLAN netdev interface. 258 * This works both as a query (user space asks the current mode) or event 259 * interface (driver advertizing the current mode to the user space). 260 * Driver does not trigger this event for temporary hardware mode changes. 261 * Mode changes w.r.t Wi-Fi connection updation ( VIZ creation / deletion, 262 * channel change etc ) are updated with this event. Attributes for this 263 * interface are defined in enum qca_wlan_vendor_attr_mac. 264 * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold 265 * per peer per TID. Attributes for this command are define in 266 * enum qca_wlan_set_qdepth_thresh_attr 267 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi 268 * test configuration. Attributes for this command are defined in 269 * enum qca_wlan_vendor_attr_wifi_test_config. 270 * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor 271 * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, 272 * carried a payload which was a binary blob of data. The command was not 273 * extendable to send more information. The newer version carries the 274 * legacy blob encapsulated within an attribute and can be extended with 275 * additional vendor attributes that can enhance the NAN command 276 * interface. 277 * @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: Sub command to get firmware state. 278 * The returned firmware state is specified in the attribute 279 * QCA_WLAN_VENDOR_ATTR_FW_STATE. 280 * 281 */ 282 283 enum qca_nl80211_vendor_subcmds { 284 QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, 285 QCA_NL80211_VENDOR_SUBCMD_TEST = 1, 286 QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, 287 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, 288 QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, 289 QCA_NL80211_VENDOR_SUBCMD_NAN = 12, 290 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, 291 292 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, 293 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, 294 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, 295 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, 296 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, 297 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, 298 299 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START = 20, 300 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP = 21, 301 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS = 22, 302 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES = 23, 303 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS = 24, 304 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE = 25, 305 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT = 26, 306 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT = 27, 307 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND = 28, 308 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST = 29, 309 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST = 30, 310 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE = 31, 311 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE = 32, 312 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE = 33, 313 314 QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, 315 QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, 316 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, 317 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, 318 319 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, 320 321 QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, 322 QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, 323 324 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST = 41, 325 326 /* Get Concurrency Matrix */ 327 QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, 328 329 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, 330 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, 331 QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, 332 333 /* Deprecated */ 334 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_SCHED = 53, 335 336 QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, 337 338 QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, 339 340 /* Off loaded DFS events */ 341 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, 342 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, 343 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, 344 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, 345 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, 346 347 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, 348 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, 349 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, 350 QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, 351 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST = 65, 352 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST = 66, 353 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND = 67, 354 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST = 68, 355 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_LIST = 69, 356 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_PASSPOINT_LIST = 70, 357 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_RESET_PASSPOINT_LIST = 71, 358 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND = 72, 359 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND = 73, 360 361 /* Wi-Fi Configuration subcommands */ 362 QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, 363 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, 364 QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, 365 QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, 366 367 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, 368 QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, 369 QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, 370 QCA_NL80211_VENDOR_SUBCMD_NDP = 81, 371 372 /* NS Offload enable/disable cmd */ 373 QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, 374 375 QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, 376 QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, 377 378 QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, 379 380 QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, 381 /* OCB commands */ 382 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, 383 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, 384 QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, 385 QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, 386 QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, 387 QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, 388 QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, 389 QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, 390 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, 391 392 /* subcommand to get link properties */ 393 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, 394 /* LFR Subnet Detection */ 395 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, 396 397 /* DBS subcommands */ 398 QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, 399 QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, 400 401 /* Vendor setband command */ 402 QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, 403 404 /* Vendor scan commands */ 405 QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, 406 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, 407 408 /* OTA test subcommand */ 409 QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, 410 /* Tx power scaling subcommands */ 411 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, 412 /* Tx power scaling in db subcommands */ 413 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE_DECR_DB = 115, 414 QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY = 116, 415 QCA_NL80211_VENDOR_SUBCMD_STA_CONNECT_ROAM_POLICY = 117, 416 QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, 417 QCA_NL80211_VENDOR_SUBCMD_TSF = 119, 418 QCA_NL80211_VENDOR_SUBCMD_WISA = 120, 419 QCA_NL80211_VENDOR_SUBCMD_GET_STATION = 121, 420 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, 421 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, 422 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, 423 QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, 424 425 QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, 426 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, 427 /* FTM/indoor location subcommands */ 428 QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, 429 QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, 430 QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, 431 QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, 432 QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, 433 QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, 434 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, 435 QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, 436 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, 437 438 /* Encrypt/Decrypt command */ 439 QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, 440 441 QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, 442 /* DMG low level RF sector operations */ 443 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, 444 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, 445 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, 446 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, 447 448 /* Configure the TDLS mode from user space */ 449 QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, 450 451 QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, 452 453 /* Vendor abort scan command */ 454 QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, 455 456 /* Set Specific Absorption Rate(SAR) Power Limits */ 457 QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, 458 459 /* External Auto channel configuration setting */ 460 QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, 461 462 QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, 463 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, 464 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, 465 QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, 466 467 /* Set the trace level for QDF */ 468 QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, 469 470 QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, 471 472 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, 473 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, 474 QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, 475 QCA_NL80211_VENDOR_SUBCMD_HANG = 157, 476 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, 477 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, 478 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, 479 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, 480 QCA_NL80211_VENDOR_SUBCMD_HTT_STATS = 162, 481 QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, 482 QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, 483 QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, 484 QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, 485 /* Wi-Fi test configuration subcommand */ 486 QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, 487 QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, 488 QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, 489 QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177, 490 }; 491 492 enum qca_wlan_vendor_tos { 493 QCA_WLAN_VENDOR_TOS_BK = 0, 494 QCA_WLAN_VENDOR_TOS_BE = 1, 495 QCA_WLAN_VENDOR_TOS_VI = 2, 496 QCA_WLAN_VENDOR_TOS_VO = 3, 497 }; 498 499 /** 500 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command 501 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. 502 */ 503 enum qca_wlan_vendor_attr_active_tos { 504 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, 505 /* Type Of Service - Represented by qca_wlan_vendor_tos */ 506 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, 507 /* Flag attribute representing the start (attribute included) or stop 508 * (attribute not included) of the respective TOS. 509 */ 510 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, 511 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_MAX = 3, 512 }; 513 514 enum qca_wlan_vendor_hang_reason { 515 /* Unspecified reason */ 516 QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, 517 /* No Map for the MAC entry for the received frame */ 518 QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, 519 /* peer deletion timeout happened */ 520 QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, 521 /* peer unmap timeout */ 522 QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, 523 /* Scan request timed out */ 524 QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, 525 /* Consecutive Scan attempt failures */ 526 QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, 527 /* Unable to get the message buffer */ 528 QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, 529 /* Current command processing is timedout */ 530 QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, 531 /* Timeout for an ACK from FW for suspend request */ 532 QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, 533 /* Timeout for an ACK from FW for resume request */ 534 QCA_WLAN_HANG_RESUME_TIMEOUT = 9, 535 /* Transmission timeout for consecutive data frames */ 536 QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, 537 /* Timeout for the TX completion status of data frame */ 538 QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, 539 /* DXE failure for tx/Rx, DXE resource unavailability */ 540 QCA_WLAN_HANG_DXE_FAILURE = 12, 541 /* WMI pending commands exceed the maximum count */ 542 QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, 543 }; 544 545 /** 546 * enum qca_wlan_vendor_attr_hang - Used by the vendor command 547 * QCA_NL80211_VENDOR_SUBCMD_HANG. 548 */ 549 enum qca_wlan_vendor_attr_hang { 550 QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, 551 /* 552 * Reason for the Hang - Represented by enum 553 * qca_wlan_vendor_hang_reason. 554 */ 555 QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, 556 557 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, 558 QCA_WLAN_VENDOR_ATTR_HANG_MAX = 559 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, 560 }; 561 562 /** 563 * enum qca_vendor_attr_set_trace_level - Config params for QDF set trace level 564 * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_INVALID: Invalid trace level 565 * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM : Trace level parameters 566 * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MODULE_ID : Module of which trace 567 level needs to be updated. 568 * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_TRACE_MASK : verbose mask, which need 569 * to be set. 570 * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST : after last. 571 * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MAX : Max attribute. 572 */ 573 enum qca_vendor_attr_set_trace_level { 574 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_INVALID = 0, 575 /* 576 * Array of QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM 577 * attributes. 578 */ 579 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM = 1, 580 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MODULE_ID = 2, 581 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_TRACE_MASK = 3, 582 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST, 583 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MAX = 584 QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST - 1, 585 }; 586 587 /** 588 * enum qca_wlan_vendor_attr_get_station - Sub commands used by 589 * QCA_NL80211_VENDOR_SUBCMD_GET_STATION to get the corresponding 590 * station information. The information obtained through these 591 * commands signify the current info in connected state and 592 * latest cached information during the connected state , if queried 593 * when in disconnected state. 594 * 595 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INVALID: Invalid attribute 596 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO: bss info 597 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_ASSOC_FAIL_REASON: assoc fail reason 598 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_REMOTE: remote station info 599 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST: After last 600 */ 601 enum qca_wlan_vendor_attr_get_station { 602 QCA_WLAN_VENDOR_ATTR_GET_STATION_INVALID = 0, 603 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO, 604 QCA_WLAN_VENDOR_ATTR_GET_STATION_ASSOC_FAIL_REASON, 605 QCA_WLAN_VENDOR_ATTR_GET_STATION_REMOTE, 606 607 /* keep last */ 608 QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST, 609 QCA_WLAN_VENDOR_ATTR_GET_STATION_MAX = 610 QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST - 1, 611 }; 612 613 /** 614 * enum qca_wlan_802_11_mode - dot11 mode 615 * @QCA_WLAN_802_11_MODE_11B: mode B 616 * @QCA_WLAN_802_11_MODE_11G: mode G 617 * @QCA_WLAN_802_11_MODE_11N: mode N 618 * @QCA_WLAN_802_11_MODE_11A: mode A 619 * @QCA_WLAN_802_11_MODE_11AC: mode AC 620 * @QCA_WLAN_802_11_MODE_INVALID: Invalid dot11 mode 621 */ 622 enum qca_wlan_802_11_mode { 623 QCA_WLAN_802_11_MODE_11B, 624 QCA_WLAN_802_11_MODE_11G, 625 QCA_WLAN_802_11_MODE_11N, 626 QCA_WLAN_802_11_MODE_11A, 627 QCA_WLAN_802_11_MODE_11AC, 628 QCA_WLAN_802_11_MODE_INVALID, 629 }; 630 631 /** 632 * enum qca_wlan_auth_type - Authentication key management type 633 * @QCA_WLAN_AUTH_TYPE_INVALID: Invalid key management type 634 * @QCA_WLAN_AUTH_TYPE_OPEN: Open key 635 * @QCA_WLAN_AUTH_TYPE_SHARED: shared key 636 * @QCA_WLAN_AUTH_TYPE_WPA: wpa key 637 * @QCA_WLAN_AUTH_TYPE_WPA_PSK: wpa psk key 638 * @QCA_WLAN_AUTH_TYPE_WPA_NONE: wpa none key 639 * @QCA_WLAN_AUTH_TYPE_RSN: rsn key 640 * @QCA_WLAN_AUTH_TYPE_RSN_PSK: rsn psk key 641 * @QCA_WLAN_AUTH_TYPE_FT: ft key 642 * @QCA_WLAN_AUTH_TYPE_FT_PSK: ft psk key 643 * @QCA_WLAN_AUTH_TYPE_SHA256: shared 256 key 644 * @QCA_WLAN_AUTH_TYPE_SHA256_PSK: shared 256 psk 645 * @QCA_WLAN_AUTH_TYPE_WAI: wai key 646 * @QCA_WLAN_AUTH_TYPE_WAI_PSK wai psk key 647 * @QCA_WLAN_AUTH_TYPE_CCKM_WPA: cckm wpa key 648 * @QCA_WLAN_AUTH_TYPE_CCKM_RSN: cckm rsn key 649 * @QCA_WLAN_AUTH_TYPE_FT_SAE: FT sae akm 650 * @QCA_WLAN_AUTH_TYPE_FT_SUITEB_EAP_SHA384: FT suite B SHA384 651 */ 652 enum qca_wlan_auth_type { 653 QCA_WLAN_AUTH_TYPE_INVALID, 654 QCA_WLAN_AUTH_TYPE_OPEN, 655 QCA_WLAN_AUTH_TYPE_SHARED, 656 QCA_WLAN_AUTH_TYPE_WPA, 657 QCA_WLAN_AUTH_TYPE_WPA_PSK, 658 QCA_WLAN_AUTH_TYPE_WPA_NONE, 659 QCA_WLAN_AUTH_TYPE_RSN, 660 QCA_WLAN_AUTH_TYPE_RSN_PSK, 661 QCA_WLAN_AUTH_TYPE_FT, 662 QCA_WLAN_AUTH_TYPE_FT_PSK, 663 QCA_WLAN_AUTH_TYPE_SHA256, 664 QCA_WLAN_AUTH_TYPE_SHA256_PSK, 665 QCA_WLAN_AUTH_TYPE_WAI, 666 QCA_WLAN_AUTH_TYPE_WAI_PSK, 667 QCA_WLAN_AUTH_TYPE_CCKM_WPA, 668 QCA_WLAN_AUTH_TYPE_CCKM_RSN, 669 QCA_WLAN_AUTH_TYPE_AUTOSWITCH, 670 QCA_WLAN_AUTH_TYPE_FT_SAE, 671 QCA_WLAN_AUTH_TYPE_FT_SUITEB_EAP_SHA384, 672 }; 673 674 /** 675 * enum qca_wlan_vendor_attr_get_station_info - Station Info queried 676 * through QCA_NL80211_VENDOR_SUBCMD_GET_STATION. 677 * 678 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_INVALID: Invalid Attribute 679 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_LINK_STANDARD_NL80211_ATTR: 680 * Get the standard NL attributes Nested with this attribute. 681 * Ex : Query BW , BITRATE32 , NSS , Signal , Noise of the Link - 682 * NL80211_ATTR_SSID / NL80211_ATTR_SURVEY_INFO (Connected Channel) / 683 * NL80211_ATTR_STA_INFO 684 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_STANDARD_NL80211_ATTR: 685 * Get the standard NL attributes Nested with this attribute. 686 * Ex : Query HT/VHT Capability advertized by the AP. 687 * NL80211_ATTR_VHT_CAPABILITY / NL80211_ATTR_HT_CAPABILITY 688 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ROAM_COUNT: 689 * Number of successful Roam attempts before a 690 * disconnect, Unsigned 32 bit value 691 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AKM: 692 * Authentication Key Management Type used for the connected session. 693 * Signified by enum qca_wlan_auth_type 694 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_802_11_MODE: 802.11 Mode of the 695 * connected Session, signified by enum qca_wlan_802_11_mode 696 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_HS20_INDICATION: 697 * HS20 Indication Element 698 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_FAIL_REASON: 699 * Status Code Corresponding to the Association Failure. 700 * Unsigned 32 bit value. 701 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_MAX_PHY_RATE: 702 * Max phy rate of remote station 703 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_PACKETS: 704 * TX packets to remote station 705 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_BYTES: 706 * TX bytes to remote station 707 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_PACKETS: 708 * RX packets from remote station 709 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BYTES: 710 * RX bytes from remote station 711 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_TX_RATE: 712 * Last TX rate with remote station 713 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_RX_RATE: 714 * Last RX rate with remote station 715 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_WMM: 716 * Remote station enable/disable WMM 717 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SUPPORTED_MODE: 718 * Remote station connection mode 719 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AMPDU: 720 * Remote station AMPDU enable/disable 721 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_STBC: 722 * Remote station TX Space-time block coding enable/disable 723 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_STBC: 724 * Remote station RX Space-time block coding enable/disable 725 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH: 726 * Remote station channel width 727 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SGI_ENABLE: 728 * Remote station short GI enable/disable 729 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_PAD: Attribute type for padding 730 * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST: After last 731 */ 732 enum qca_wlan_vendor_attr_get_station_info { 733 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_INVALID = 0, 734 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_LINK_STANDARD_NL80211_ATTR, 735 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_STANDARD_NL80211_ATTR, 736 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ROAM_COUNT, 737 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AKM, 738 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_802_11_MODE, 739 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_HS20_INDICATION, 740 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_HT_OPERATION, 741 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_VHT_OPERATION, 742 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_FAIL_REASON, 743 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_MAX_PHY_RATE, 744 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_PACKETS, 745 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_BYTES, 746 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_PACKETS, 747 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BYTES, 748 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_TX_RATE, 749 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_RX_RATE, 750 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_WMM, 751 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SUPPORTED_MODE, 752 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AMPDU, 753 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_STBC, 754 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_STBC, 755 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH, 756 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SGI_ENABLE, 757 #if (LINUX_VERSION_CODE >= KERNEL_VERSION(4, 7, 0)) 758 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_PAD, 759 #endif 760 /* keep last */ 761 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST, 762 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_MAX = 763 QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST - 1, 764 }; 765 766 /** 767 * enum qca_nl80211_vendor_subcmds_index - vendor sub commands index 768 * 769 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_INDEX: Avoid frequency 770 * @QCA_NL80211_VENDOR_SUBCMD_NAN_INDEX: Nan 771 * @QCA_NL80211_VENDOR_SUBCMD_STATS_EXT_INDEX: Ext stats 772 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START_INDEX: Ext scan start 773 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP_INDEX: Ext scan stop 774 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES_INDEX: Ext scan get 775 * capability 776 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS_INDEX: Ext scan get 777 * cached results 778 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE_INDEX: Ext scan 779 * results available 780 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT_INDEX: Ext scan full 781 * scan result 782 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT_INDEX: Ext scan event 783 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND_INDEX: Ext scan hot list 784 * AP found 785 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST_INDEX: Ext scan set 786 * bssid hotlist 787 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST_INDEX: Ext scan reset 788 * bssid hotlist 789 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE_INDEX: Ext scan 790 * significant change 791 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE_INDEX: Ext scan 792 * set significant change 793 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE_INDEX: Ext scan 794 * reset significant change 795 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET_INDEX: Set stats 796 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET_INDEX: Get stats 797 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR_INDEX: Clear stats 798 * @QCA_NL80211_VENDOR_SUBCMD_LL_RADIO_STATS_INDEX: Radio stats 799 * @QCA_NL80211_VENDOR_SUBCMD_LL_IFACE_STATS_INDEX: Iface stats 800 * @QCA_NL80211_VENDOR_SUBCMD_LL_PEER_INFO_STATS_INDEX: Peer info stats 801 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT_INDEX: MAC layer counters 802 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE_CHANGE_INDEX: Ext tdls state change 803 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS_INDEX: ACS command 804 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH_INDEX: Pass Roam and Auth info 805 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST_INDEX: hotlist ap lost 806 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND_INDEX: 807 * pno network found index 808 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND_INDEX: 809 * passpoint match found index 810 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST_INDEX: 811 * set ssid hotlist index 812 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST_INDEX: 813 * reset ssid hotlist index 814 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND_INDEX: 815 * hotlist ssid found index 816 * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST_INDEX: 817 * hotlist ssid lost index 818 * @QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT_INDEX 819 * dcc stats event index 820 * @QCA_NL80211_VENDOR_SUBCMD_SCAN_INDEX: vendor scan index 821 * @QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE_INDEX: 822 * vendor scan complete event index 823 * @QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG_INDEX: 824 * update gateway parameters index 825 * @QCA_NL80211_VENDOR_SUBCMD_TSF_INDEX: TSF response events index 826 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LO_EVENT_INDEX: 827 * P2P listen offload index 828 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH_INDEX: SAP 829 * conditional channel switch index 830 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET_INDEX: NUD DEBUG Stats index 831 * @QCA_NL80211_VENDOR_SUBCMD_HANG_REASON_INDEX: hang event reason index 832 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO_INDEX: MAC mode info index 833 * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT_INDEX: NAN Extended index 834 */ 835 836 enum qca_nl80211_vendor_subcmds_index { 837 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_INDEX = 0, 838 839 QCA_NL80211_VENDOR_SUBCMD_NAN_INDEX, 840 841 #ifdef WLAN_FEATURE_STATS_EXT 842 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT_INDEX, 843 #endif /* WLAN_FEATURE_STATS_EXT */ 844 845 #ifdef FEATURE_WLAN_EXTSCAN 846 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START_INDEX, 847 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP_INDEX, 848 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES_INDEX, 849 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS_INDEX, 850 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE_INDEX, 851 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT_INDEX, 852 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT_INDEX, 853 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND_INDEX, 854 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST_INDEX, 855 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST_INDEX, 856 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE_INDEX, 857 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE_INDEX, 858 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE_INDEX, 859 #endif /* FEATURE_WLAN_EXTSCAN */ 860 861 #ifdef WLAN_FEATURE_LINK_LAYER_STATS 862 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET_INDEX, 863 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET_INDEX, 864 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR_INDEX, 865 QCA_NL80211_VENDOR_SUBCMD_LL_RADIO_STATS_INDEX, 866 QCA_NL80211_VENDOR_SUBCMD_LL_IFACE_STATS_INDEX, 867 QCA_NL80211_VENDOR_SUBCMD_LL_PEER_INFO_STATS_INDEX, 868 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT_INDEX, 869 #endif /* WLAN_FEATURE_LINK_LAYER_STATS */ 870 871 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE_CHANGE_INDEX, 872 QCA_NL80211_VENDOR_SUBCMD_DO_ACS_INDEX, 873 #ifdef WLAN_FEATURE_ROAM_OFFLOAD 874 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH_INDEX, 875 #endif 876 /* DFS */ 877 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED_INDEX, 878 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED_INDEX, 879 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED_INDEX, 880 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED_INDEX, 881 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED_INDEX, 882 #ifdef FEATURE_WLAN_EXTSCAN 883 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST_INDEX, 884 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND_INDEX, 885 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND_INDEX, 886 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST_INDEX, 887 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST_INDEX, 888 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND_INDEX, 889 QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST_INDEX, 890 #endif /* FEATURE_WLAN_EXTSCAN */ 891 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION_INDEX, 892 QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI_INDEX, 893 #ifdef WLAN_FEATURE_MEMDUMP 894 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP_INDEX, 895 #endif /* WLAN_FEATURE_MEMDUMP */ 896 /* OCB events */ 897 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT_INDEX, 898 QCA_NL80211_VENDOR_SUBCMD_SCAN_INDEX, 899 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE_INDEX, 900 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG_INDEX, 901 #ifdef WLAN_FEATURE_TSF 902 QCA_NL80211_VENDOR_SUBCMD_TSF_INDEX, 903 #endif 904 QCA_NL80211_VENDOR_SUBCMD_NDP_INDEX, 905 QCA_NL80211_VENDOR_SUBCMD_P2P_LO_EVENT_INDEX, 906 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH_INDEX, 907 QCA_NL80211_VENDOR_SUBCMD_UPDATE_EXTERNAL_ACS_CONFIG, 908 QCA_NL80211_VENDOR_SUBCMD_PWR_SAVE_FAIL_DETECTED_INDEX, 909 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET_INDEX, 910 QCA_NL80211_VENDOR_SUBCMD_HANG_REASON_INDEX, 911 QCA_NL80211_VENDOR_SUBCMD_HTT_STATS_INDEX, 912 QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO_INDEX, 913 QCA_NL80211_VENDOR_SUBCMD_NAN_EXT_INDEX, 914 QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT_INDEX, 915 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES_INDEX, 916 }; 917 918 /** 919 * enum qca_wlan_vendor_attr_tdls_enable - TDLS enable attribute 920 * 921 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_INVALID: Invalid initial value 922 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR: An array of 6 x Unsigned 8-bit 923 * value 924 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_CHANNEL: Signed 32-bit value, but lets 925 * keep as unsigned for now 926 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_GLOBAL_OPERATING_CLASS: operating class 927 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX_LATENCY_MS: Enable max latency in ms 928 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MIN_BANDWIDTH_KBPS: Enable min bandwidth 929 * in KBPS 930 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST: After last 931 * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX: Max value 932 */ 933 enum qca_wlan_vendor_attr_tdls_enable { 934 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_INVALID = 0, 935 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR, 936 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_CHANNEL, 937 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_GLOBAL_OPERATING_CLASS, 938 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX_LATENCY_MS, 939 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MIN_BANDWIDTH_KBPS, 940 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST, 941 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX = 942 QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST - 1, 943 }; 944 945 /** 946 * enum qca_wlan_vendor_attr_tdls_disable: tdls disable attribute 947 * 948 * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_INVALID: Invalid initial value 949 * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR: An array of 6 x Unsigned 950 * 8-bit value 951 * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST: After last 952 * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAX: Max value 953 */ 954 enum qca_wlan_vendor_attr_tdls_disable { 955 QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_INVALID = 0, 956 QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR, 957 QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST, 958 QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAX = 959 QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST - 1, 960 }; 961 962 /** 963 * qca_chip_power_save_failure_reason: Power save failure reason 964 * @QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL: Indicates power save failure 965 * due to protocol/module. 966 * @QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE: power save failure 967 * due to hardware 968 */ 969 enum qca_chip_power_save_failure_reason { 970 QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, 971 QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, 972 }; 973 974 /** 975 * qca_attr_chip_power_save_failure: attributes to vendor subcmd 976 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carry the requisite 977 * information leading to the power save failure. 978 * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID : invalid 979 * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON : power save failure reason 980 * represented by enum qca_chip_power_save_failure_reason 981 * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST : Last 982 * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX : Max value 983 */ 984 enum qca_attr_chip_power_save_failure { 985 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, 986 987 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, 988 989 /* keep last */ 990 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, 991 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = 992 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, 993 }; 994 995 996 /** 997 * enum qca_wlan_vendor_attr_tdls_get_status - tdls get status attribute 998 * 999 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_INVALID: Invalid initial value 1000 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR: An array of 6 x Unsigned 1001 * 8-bit value 1002 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE: get status state, 1003 * unsigned 32-bit value 1004 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_REASON: get status reason 1005 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_CHANNEL: get status channel, 1006 * unsigned 32-bit value 1007 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_GLOBAL_OPERATING_CLASS: get operating 1008 * class, unsigned 32-bit value 1009 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST: After last 1010 * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAX: Max value 1011 */ 1012 enum qca_wlan_vendor_attr_tdls_get_status { 1013 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_INVALID = 0, 1014 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR, 1015 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE, 1016 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_REASON, 1017 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_CHANNEL, 1018 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_GLOBAL_OPERATING_CLASS, 1019 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST, 1020 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAX = 1021 QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST - 1, 1022 }; 1023 1024 /** 1025 * enum qca_wlan_vendor_attr_tdls_state - tdls state attribute 1026 * 1027 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_INVALID: Initial invalid value 1028 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAC_ADDR: An array of 6 x Unsigned 1029 * 8-bit value 1030 * @QCA_WLAN_VENDOR_ATTR_TDLS_NEW_STATE: TDLS new state, 1031 * unsigned 32-bit value 1032 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_REASON: TDLS state reason 1033 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CHANNEL: TDLS state channel, 1034 * unsigned 32-bit value 1035 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_GLOBAL_OPERATING_CLASS: TDLS state 1036 * operating class, unsigned 32-bit value 1037 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST: After last 1038 * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAX: Max value 1039 */ 1040 enum qca_wlan_vendor_attr_tdls_state { 1041 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_INVALID = 0, 1042 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAC_ADDR, 1043 QCA_WLAN_VENDOR_ATTR_TDLS_NEW_STATE, 1044 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_REASON, 1045 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CHANNEL, 1046 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_GLOBAL_OPERATING_CLASS, 1047 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST, 1048 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAX = 1049 QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST - 1, 1050 }; 1051 1052 /* enum's to provide TDLS capabilities */ 1053 enum qca_wlan_vendor_attr_get_tdls_capabilities { 1054 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, 1055 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS = 1, 1056 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED = 2, 1057 1058 /* keep last */ 1059 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, 1060 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = 1061 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, 1062 }; 1063 1064 enum qca_wlan_vendor_attr { 1065 QCA_WLAN_VENDOR_ATTR_INVALID = 0, 1066 /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ 1067 QCA_WLAN_VENDOR_ATTR_DFS = 1, 1068 /* used by QCA_NL80211_VENDOR_SUBCMD_NAN */ 1069 QCA_WLAN_VENDOR_ATTR_NAN = 2, 1070 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 1071 QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, 1072 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 1073 QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, 1074 /* 1075 * used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined 1076 * by enum qca_roaming_policy. 1077 */ 1078 QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, 1079 QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, 1080 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 1081 QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, 1082 QCA_WLAN_VENDOR_ATTR_TEST = 8, 1083 /* 1084 * used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES 1085 * Unsigned 32-bit value. 1086 */ 1087 QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, 1088 /* Unsigned 32-bit value */ 1089 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, 1090 /* Unsigned 32-bit value */ 1091 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, 1092 /* Unsigned 32-bit value from enum qca_set_band. */ 1093 QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, 1094 /* Dummy (NOP) attribute for 64 bit padding */ 1095 QCA_WLAN_VENDOR_ATTR_PAD = 13, 1096 /* 1097 * Unique FTM session cookie (Unsigned 64 bit). Specified in 1098 * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in 1099 * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and 1100 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. 1101 */ 1102 QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, 1103 /* 1104 * Indoor location capabilities, returned by 1105 * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. 1106 * see enum qca_wlan_vendor_attr_loc_capa. 1107 */ 1108 QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, 1109 /* 1110 * Array of nested attributes containing information about each peer 1111 * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info 1112 * for supported attributes for each peer. 1113 */ 1114 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, 1115 /* 1116 * Array of nested attributes containing measurement results for 1117 * one or more peers, reported by the 1118 * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. 1119 * See enum qca_wlan_vendor_attr_peer_result for list of supported 1120 * attributes. 1121 */ 1122 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, 1123 /* Flag attribute for enabling or disabling responder functionality. */ 1124 QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, 1125 /* 1126 * Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 1127 * command to specify the LCI report that will be sent by 1128 * the responder during a measurement exchange. The format is 1129 * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. 1130 */ 1131 QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, 1132 /* 1133 * Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 1134 * command to specify the location civic report that will 1135 * be sent by the responder during a measurement exchange. 1136 * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. 1137 */ 1138 QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, 1139 /* 1140 * Session/measurement completion status code, 1141 * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and 1142 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT 1143 * see enum qca_vendor_attr_loc_session_status. 1144 */ 1145 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, 1146 /* 1147 * Initial dialog token used by responder (0 if not specified), 1148 * unsigned 8 bit value. 1149 */ 1150 QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, 1151 /* 1152 * AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS 1153 * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if 1154 * AOA measurements are needed as part of an FTM session. 1155 * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See 1156 * enum qca_wlan_vendor_attr_aoa_type. 1157 */ 1158 QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, 1159 /* 1160 * A bit mask (unsigned 32 bit value) of antenna arrays used 1161 * by indoor location measurements. Refers to the antenna 1162 * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. 1163 */ 1164 QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, 1165 /* 1166 * AOA measurement data. Its contents depends on the AOA measurement 1167 * type and antenna array mask: 1168 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, 1169 * phase of the strongest CIR path for each antenna in the measured 1170 * array(s). 1171 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 1172 * values, phase and amplitude of the strongest CIR path for each 1173 * antenna in the measured array(s). 1174 */ 1175 QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, 1176 /* 1177 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1178 * to specify the chain number (unsigned 32 bit value) to inquire 1179 * the corresponding antenna RSSI value */ 1180 QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, 1181 /* 1182 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1183 * to report the specific antenna RSSI value (unsigned 32 bit value) */ 1184 QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, 1185 /* Frequency in MHz, various uses. Unsigned 32 bit value */ 1186 QCA_WLAN_VENDOR_ATTR_FREQ = 28, 1187 /* 1188 * TSF timer value, unsigned 64 bit value. 1189 * May be returned by various commands. 1190 */ 1191 QCA_WLAN_VENDOR_ATTR_TSF = 29, 1192 /* 1193 * DMG RF sector index, unsigned 16 bit number. Valid values are 1194 * 0..127 for sector indices or 65535 as special value used to 1195 * unlock sector selection in 1196 * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. 1197 */ 1198 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, 1199 /* 1200 * DMG RF sector type, unsigned 8 bit value. One of the values 1201 * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. 1202 */ 1203 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, 1204 /* 1205 * Bitmask of DMG RF modules for which information is requested. Each 1206 * bit corresponds to an RF module with the same index as the bit 1207 * number. Unsigned 32 bit number but only low 8 bits can be set since 1208 * all DMG chips currently have up to 8 RF modules. 1209 */ 1210 QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, 1211 /* 1212 * Array of nested attributes where each entry is DMG RF sector 1213 * configuration for a single RF module. 1214 * Attributes for each entry are taken from enum 1215 * qca_wlan_vendor_attr_dmg_rf_sector_cfg. 1216 * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG 1217 * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. 1218 */ 1219 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, 1220 /* 1221 * Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command 1222 * to report frame aggregation statistics to userspace. 1223 */ 1224 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, 1225 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, 1226 /* 1227 * Unsigned 8-bit value representing MBO transition reason code as 1228 * provided by the AP used by subcommand 1229 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is 1230 * specified by the userspace in the request to the driver. 1231 */ 1232 QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, 1233 /* 1234 * Array of nested attributes, BSSID and status code, used by subcommand 1235 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each 1236 * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. 1237 * The userspace space specifies the list/array of candidate BSSIDs in 1238 * the order of preference in the request. The driver specifies the 1239 * status code, for each BSSID in the list, in the response. The 1240 * acceptable candidates are listed in the order preferred by the 1241 * driver. 1242 */ 1243 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, 1244 /* 1245 * Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 1246 * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. 1247 */ 1248 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, 1249 /* 1250 * Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 1251 * to define the number of antennas to use for BRP. 1252 * different purpose in each ANT_LIMIT_MODE: 1253 * DISABLE - ignored 1254 * EFFECTIVE - upper limit to number of antennas to be used 1255 * FORCE - exact number of antennas to be used 1256 * unsigned 8 bit value 1257 */ 1258 QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, 1259 /* 1260 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1261 * to report the corresponding antenna index to the chain RSSI value 1262 */ 1263 QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, 1264 /* 1265 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1266 * to report the specific antenna EVM value (unsigned 32 bit value). 1267 * With a determinate group of antennas, the driver specifies the 1268 * EVM value for each antenna ID, and application extract them 1269 * in user space. 1270 */ 1271 QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41, 1272 /* 1273 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report 1274 * wlan firmware current state. FW state is an unsigned 8 bit value, 1275 * one of the values in enum qca_wlan_vendor_attr_fw_state. 1276 */ 1277 QCA_WLAN_VENDOR_ATTR_FW_STATE = 42, 1278 1279 /* keep last */ 1280 QCA_WLAN_VENDOR_ATTR_AFTER_LAST, 1281 QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1 1282 }; 1283 1284 #ifdef FEATURE_WLAN_EXTSCAN 1285 enum qca_wlan_vendor_attr_extscan_config_params { 1286 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, 1287 1288 /* Unsigned 32-bit value */ 1289 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, 1290 1291 /* 1292 * Attributes for data used by 1293 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS sub command. 1294 */ 1295 1296 /* Unsigned 32-bit value */ 1297 QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND 1298 = 2, 1299 /* Unsigned 32-bit value */ 1300 QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS 1301 = 3, 1302 1303 /* 1304 * Attributes for input params used by 1305 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START sub command. 1306 */ 1307 1308 /* Unsigned 32-bit value; channel frequency */ 1309 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_CHANNEL = 4, 1310 /* Unsigned 32-bit value; dwell time in ms. */ 1311 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_DWELL_TIME = 5, 1312 /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ 1313 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_PASSIVE = 6, 1314 /* Unsigned 8-bit value; channel class */ 1315 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_CLASS = 7, 1316 1317 /* Unsigned 8-bit value; bucket index, 0 based */ 1318 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_INDEX = 8, 1319 /* Unsigned 8-bit value; band. */ 1320 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_BAND = 9, 1321 /* Unsigned 32-bit value; desired period, in ms. */ 1322 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_PERIOD = 10, 1323 /* Unsigned 8-bit value; report events semantics. */ 1324 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, 1325 /* 1326 * Unsigned 32-bit value. Followed by a nested array of 1327 * EXTSCAN_CHANNEL_SPEC_* attributes. 1328 */ 1329 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, 1330 1331 /* 1332 * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_* attributes. 1333 * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 1334 */ 1335 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC = 13, 1336 1337 /* Unsigned 32-bit value; base timer period in ms. */ 1338 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, 1339 /* 1340 * Unsigned 32-bit value; number of APs to store in each scan in the 1341 * BSSID/RSSI history buffer (keep the highest RSSI APs). 1342 */ 1343 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, 1344 /* 1345 * Unsigned 8-bit value; in %, when scan buffer is this much full, wake 1346 * up AP. 1347 */ 1348 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT 1349 = 16, 1350 1351 /* 1352 * Unsigned 8-bit value; number of scan bucket specs; followed by a 1353 * nested array of_EXTSCAN_BUCKET_SPEC_* attributes and values. The size 1354 * of the array is determined by NUM_BUCKETS. 1355 */ 1356 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, 1357 1358 /* 1359 * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_* attributes. 1360 * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS 1361 */ 1362 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC = 18, 1363 1364 /* Unsigned 8-bit value */ 1365 QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH 1366 = 19, 1367 /* Unsigned 32-bit value; maximum number of results to be returned. */ 1368 QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX 1369 = 20, 1370 1371 /* An array of 6 x unsigned 8-bit value */ 1372 QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_BSSID = 21, 1373 /* Signed 32-bit value */ 1374 QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, 1375 /* Signed 32-bit value */ 1376 QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, 1377 /* Unsigned 32-bit value */ 1378 QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, 1379 1380 /* 1381 * Number of hotlist APs as unsigned 32-bit value, followed by a nested 1382 * array of AP_THRESHOLD_PARAM attributes and values. The size of the 1383 * array is determined by NUM_AP. 1384 */ 1385 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, 1386 1387 /* 1388 * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_* attributes. 1389 * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 1390 */ 1391 QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM = 26, 1392 1393 /* Unsigned 32-bit value; number of samples for averaging RSSI. */ 1394 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE 1395 = 27, 1396 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 1397 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE 1398 = 28, 1399 /* Unsigned 32-bit value; number of APs breaching threshold. */ 1400 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, 1401 /* 1402 * Unsigned 32-bit value; number of APs. Followed by an array of 1403 * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. 1404 */ 1405 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, 1406 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 1407 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE 1408 = 31, 1409 /* 1410 * Unsigned 32-bit value. If max_period is non zero or different than 1411 * period, then this bucket is an exponential backoff bucket. 1412 */ 1413 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_MAX_PERIOD = 32, 1414 /* Unsigned 32-bit value. */ 1415 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_BASE = 33, 1416 /* 1417 * Unsigned 32-bit value. For exponential back off bucket, number of 1418 * scans to perform for a given period. 1419 */ 1420 QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_STEP_COUNT = 34, 1421 /* 1422 * Unsigned 8-bit value; in number of scans, wake up AP after these 1423 * many scans. 1424 */ 1425 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS 1426 = 35, 1427 1428 /* 1429 * Attributes for data used by 1430 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST sub command. 1431 */ 1432 1433 /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ 1434 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE 1435 = 36, 1436 /* 1437 * Number of hotlist SSIDs as unsigned 32-bit value, followed by a 1438 * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The 1439 * size of the array is determined by NUM_SSID. 1440 */ 1441 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, 1442 /* 1443 * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_* 1444 * attributes. 1445 * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_NUM_SSID 1446 */ 1447 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM = 38, 1448 1449 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 1450 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_SSID = 39, 1451 /* Unsigned 8-bit value */ 1452 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_BAND = 40, 1453 /* Signed 32-bit value */ 1454 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, 1455 /* Signed 32-bit value */ 1456 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, 1457 /* Unsigned 32-bit value; a bitmask with additional extscan config flag. 1458 */ 1459 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CONFIGURATION_FLAGS = 43, 1460 1461 /* keep last */ 1462 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, 1463 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_MAX = 1464 QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, 1465 }; 1466 1467 enum qca_wlan_vendor_attr_extscan_results { 1468 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_INVALID = 0, 1469 1470 /* 1471 * Unsigned 32-bit value; must match the request Id supplied by 1472 * Wi-Fi HAL in the corresponding subcmd NL msg. 1473 */ 1474 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_REQUEST_ID = 1, 1475 1476 /* 1477 * Unsigned 32-bit value; used to indicate the status response from 1478 * firmware/driver for the vendor sub-command. 1479 */ 1480 QCA_WLAN_VENDOR_ATTR_EXTSCAN_STATUS = 2, 1481 1482 /* 1483 * EXTSCAN Valid Channels attributes */ 1484 /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ 1485 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_CHANNELS = 3, 1486 /* 1487 * An array of NUM_CHANNELS x unsigned 32-bit value integers 1488 * representing channel numbers. 1489 */ 1490 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CHANNELS = 4, 1491 1492 /* EXTSCAN Capabilities attributes */ 1493 1494 /* Unsigned 32-bit value */ 1495 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, 1496 /* Unsigned 32-bit value */ 1497 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, 1498 /* Unsigned 32-bit value */ 1499 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN 1500 = 7, 1501 /* Unsigned 32-bit value */ 1502 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE 1503 = 8, 1504 /* Signed 32-bit value */ 1505 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD 1506 = 9, 1507 /* Unsigned 32-bit value */ 1508 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, 1509 /* Unsigned 32-bit value */ 1510 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS 1511 = 11, 1512 /* Unsigned 32-bit value */ 1513 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES 1514 = 12, 1515 1516 /* 1517 * EXTSCAN Attributes used with 1518 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE sub-command. 1519 */ 1520 1521 /* Unsigned 32-bit value */ 1522 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, 1523 1524 /* 1525 * EXTSCAN attributes used with 1526 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT sub-command. 1527 */ 1528 1529 /* 1530 * An array of NUM_RESULTS_AVAILABLE x 1531 * QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_* 1532 */ 1533 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST = 14, 1534 1535 /* Unsigned 64-bit value; age of sample at the time of retrieval */ 1536 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, 1537 /* 33 x unsigned 8-bit value; NULL terminated SSID */ 1538 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_SSID = 16, 1539 /* An array of 6 x unsigned 8-bit value */ 1540 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_BSSID = 17, 1541 /* Unsigned 32-bit value; channel frequency in MHz */ 1542 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, 1543 /* Signed 32-bit value */ 1544 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RSSI = 19, 1545 /* Unsigned 32-bit value */ 1546 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RTT = 20, 1547 /* Unsigned 32-bit value */ 1548 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, 1549 /* Unsigned 16-bit value */ 1550 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, 1551 /* Unsigned 16-bit value */ 1552 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, 1553 /* Unsigned 32-bit value; size of the IE DATA blob */ 1554 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, 1555 /* 1556 * An array of IE_LENGTH x unsigned 8-bit value; blob of all the 1557 * information elements found in the beacon; this data should be a 1558 * packed list of wifi_information_element objects, one after the 1559 * other. 1560 */ 1561 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, 1562 1563 /* 1564 * Unsigned 8-bit value; set by driver to indicate more scan results are 1565 * available. 1566 */ 1567 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, 1568 1569 /* 1570 * EXTSCAN attributes for 1571 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT sub-command. 1572 */ 1573 /* Unsigned 8-bit value */ 1574 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_EVENT_TYPE = 27, 1575 /* Unsigned 32-bit value */ 1576 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_EVENT_STATUS = 28, 1577 1578 /* 1579 * EXTSCAN attributes for 1580 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND sub-command. 1581 */ 1582 /* 1583 * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE 1584 * to indicate number of results. 1585 * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the 1586 * list of results. 1587 */ 1588 1589 /* 1590 * EXTSCAN attributes for 1591 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE sub-command. 1592 */ 1593 /* An array of 6 x unsigned 8-bit value */ 1594 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, 1595 /* Unsigned 32-bit value */ 1596 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL 1597 = 30, 1598 /* Unsigned 32-bit value. */ 1599 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI 1600 = 31, 1601 /* 1602 * A nested array of signed 32-bit RSSI values. Size of the array is 1603 * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. 1604 */ 1605 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST 1606 = 32, 1607 1608 /* 1609 * EXTSCAN attributes used with 1610 * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS sub-command. 1611 */ 1612 /* 1613 * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE 1614 * to indicate number of extscan cached results returned. 1615 * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_LIST to indicate 1616 * the list of extscan cached results. 1617 */ 1618 1619 /* 1620 * An array of NUM_RESULTS_AVAILABLE x 1621 * QCA_NL80211_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_* 1622 */ 1623 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_LIST = 33, 1624 /* Unsigned 32-bit value; a unique identifier for the scan unit. */ 1625 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_SCAN_ID = 34, 1626 /* 1627 * Unsigned 32-bit value; a bitmask w/additional information about scan. 1628 */ 1629 QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_FLAGS = 35, 1630 /* 1631 * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE 1632 * to indicate number of wifi scan results/bssids retrieved by the scan. 1633 * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the 1634 * list of wifi scan results returned for each cached result block. 1635 */ 1636 1637 /* 1638 * EXTSCAN attributes for 1639 * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. 1640 */ 1641 /* 1642 * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE for 1643 * number of results. 1644 * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the nested 1645 * list of wifi scan results returned for each 1646 * wifi_passpoint_match_result block. 1647 * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE. 1648 */ 1649 1650 /* 1651 * EXTSCAN attributes for 1652 * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. 1653 */ 1654 /* Unsigned 32-bit value */ 1655 QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES 1656 = 36, 1657 /* 1658 * A nested array of 1659 * QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_* 1660 * attributes. Array size = 1661 * *_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. 1662 */ 1663 QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, 1664 1665 /* Unsigned 32-bit value; network block id for the matched network */ 1666 QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, 1667 /* 1668 * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the nested 1669 * list of wifi scan results returned for each 1670 * wifi_passpoint_match_result block. 1671 */ 1672 /* Unsigned 32-bit value */ 1673 QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, 1674 /* 1675 * An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; 1676 * ANQP data in the information_element format. 1677 */ 1678 QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, 1679 1680 /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ 1681 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, 1682 /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ 1683 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, 1684 /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ 1685 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID 1686 = 43, 1687 /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ 1688 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID 1689 = 44, 1690 1691 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_BUCKETS_SCANNED = 45, 1692 QCA_WLAN_VENDOR_ATTR_EXTSCAN_MAX_NUM_BLACKLISTED_BSSID = 46, 1693 1694 /* keep last */ 1695 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_AFTER_LAST, 1696 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_MAX = 1697 QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_AFTER_LAST - 1, 1698 }; 1699 #endif 1700 1701 #ifdef WLAN_FEATURE_LINK_LAYER_STATS 1702 1703 /** 1704 * enum qca_wlan_vendor_attr_ll_stats_set - vendor attribute set stats 1705 * 1706 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID: Invalid initial value 1707 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD: Size threshold 1708 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING: 1709 * Aggresive stats gathering 1710 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST: After last 1711 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX: Max value 1712 */ 1713 enum qca_wlan_vendor_attr_ll_stats_set { 1714 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, 1715 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, 1716 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING, 1717 /* keep last */ 1718 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, 1719 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = 1720 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1 1721 }; 1722 1723 /** 1724 * enum qca_wlan_vendor_attr_ll_stats_get - vendor attribute get stats 1725 * 1726 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID: Invalid initial value 1727 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID: Unsigned 32bit value 1728 * provided by the caller issuing the GET stats command. When reporting 1729 * the stats results, the driver uses the same value to indicate which 1730 * GET request the results correspond to. 1731 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK: Get config request mask 1732 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK: Config response mask 1733 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP: Config stop response 1734 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST: After last 1735 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX: Max value 1736 */ 1737 enum qca_wlan_vendor_attr_ll_stats_get { 1738 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, 1739 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID, 1740 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK, 1741 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, 1742 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = 1743 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1 1744 }; 1745 1746 /** 1747 * enum qca_wlan_vendor_attr_ll_stats_clr - vendor attribute clear stats 1748 * 1749 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID: Invalid initial value 1750 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK: Config request mask 1751 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ: Config stop mask 1752 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK: Config response mask 1753 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP: Config stop response 1754 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST: After last 1755 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX: Max value 1756 */ 1757 enum qca_wlan_vendor_attr_ll_stats_clr { 1758 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, 1759 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK, 1760 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ, 1761 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK, 1762 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP, 1763 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, 1764 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = 1765 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1 1766 }; 1767 1768 /** 1769 * enum qca_wlan_vendor_attr_ll_stats_results_type - ll stats result type 1770 * 1771 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_INVALID: Initial invalid value 1772 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO: Link layer stats type radio 1773 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_IFACE: Link layer stats type interface 1774 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_PEER: Link layer stats type peer 1775 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_AFTER_LAST: Last value 1776 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_MAX: Max value 1777 */ 1778 enum qca_wlan_vendor_attr_ll_stats_results_type { 1779 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_INVALID = 0, 1780 1781 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO = 1, 1782 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_IFACE, 1783 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_PEER, 1784 1785 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_AFTER_LAST, 1786 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_MAX = 1787 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_AFTER_LAST - 1 1788 }; 1789 1790 /** 1791 * enum qca_wlan_vendor_attr_ll_stats_results - vendor attribute stats results 1792 * 1793 * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are nested 1794 * within the interface stats. 1795 * 1796 * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could be nested 1797 * within the interface stats. 1798 * 1799 * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are nested 1800 * within the interface stats. 1801 * 1802 * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* could be nested 1803 * within the peer info stats. 1804 * 1805 * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could be 1806 * nested within the channel stats. 1807 * 1808 * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ could be nested 1809 * within the radio stats. 1810 * 1811 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID: Invalid initial value 1812 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID: Unsigned 32bit value 1813 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX: Unsigned 32bit value 1814 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX: Unsigned 32bit value 1815 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX: Unsigned 32bit value 1816 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX: Unsigned 32bit value 1817 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT: Unsigned 32bit value 1818 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA: Unsigned 32bit value 1819 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK: Unsigned 32bit value 1820 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE: Interface mode, e.g., STA, 1821 * SOFTAP, IBSS, etc. Type = enum wifi_interface_mode 1822 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR: Interface MAC address. 1823 * An array of 6 Unsigned int8_t 1824 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE: 1825 * Type = enum wifi_connection_state, e.g., DISCONNECTED, AUTHENTICATING, 1826 * etc. Valid for STA, CLI only 1827 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING: 1828 * Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE 1829 * (is that valid for STA only?) 1830 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES: Unsigned 32bit value. 1831 * WIFI_CAPABILITY_XXX 1832 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID: NULL terminated SSID. An 1833 * array of 33 Unsigned 8bit values 1834 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID: BSSID. An array of 6 1835 * Unsigned 8bit values 1836 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR: Country string 1837 * advertised by AP. An array of 3 Unsigned 8bit values 1838 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR: Country string for 1839 * this association. An array of 3 Unsigned 8bit values 1840 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC: Type = enum wifi_traffic_ac e.g. 1841 * V0, VI, BE and BK 1842 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU: Unsigned int 32 value 1843 * corresponding to respective AC 1844 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU: Unsigned int 32 value 1845 * corresponding to respective AC 1846 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST: Unsigned int 32 value 1847 * corresponding to respective AC 1848 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST: Unsigned int 32 value 1849 * corresponding to respective AC 1850 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU: Unsigned int 32 value 1851 * corresponding to respective AC 1852 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU: Unsigned int 32 value 1853 * corresponding to respective AC 1854 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST: Unsigned int 32 value 1855 * corresponding to respective AC 1856 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES: Unsigned int 32 value 1857 * corresponding to respective AC 1858 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT: Unsigned int 32 value 1859 * corresponding to respective AC 1860 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN: Unsigned int 32 1861 * value corresponding to respective AC 1862 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX: Unsigned int 32 1863 * value corresponding to respective AC 1864 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG: Unsigned int 32 1865 * value corresponding to respective AC 1866 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES: Unsigned int 32 1867 * value corresponding to respective AC 1868 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS: Unsigned int 32 1869 * value corresponding to respective AC 1870 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE: Type = enum wifi_peer_type 1871 * Peer type, e.g., STA, AP, P2P GO etc 1872 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS: MAC addr corresponding 1873 * to respective peer. An array of 6 Unsigned 8bit values 1874 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES: Unsigned int 32bit 1875 * value representing capabilities corresponding to respective peer. 1876 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES: Unsigned 32bit value. 1877 * Number of rates 1878 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE: Unsigned int 8bit value: 1879 * 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved 1880 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS: Unsigned int 8bit value: 1881 * 0:1x1, 1:2x2, 3:3x3, 4:4x4 1882 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW: Unsigned int 8bit value: 1883 * 0:20MHz, 1:40Mhz, 2:80Mhz, 3:160Mhz 1884 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX: Unsigned int 8bit value: 1885 * OFDM/CCK rate code would be as per IEEE Std in the units of 0.5mbps 1886 * HT/VHT it would be mcs index 1887 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE: Unsigned 32bit value. 1888 * Bit rate in units of 100Kbps 1889 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU: Unsigned int 32bit value. 1890 * Number of successfully transmitted data pkts i.e., with ACK received 1891 * corresponding to the respective rate 1892 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU: Unsigned int 32bit value. 1893 * Number of received data pkts corresponding to the respective rate 1894 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST: Unsigned int 32bit value. 1895 * Number of data pkts losses, i.e., no ACK received corresponding to 1896 * the respective rate 1897 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES: Unsigned int 32bit value. 1898 * Total number of data pkt retries for the respective rate 1899 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT: Unsigned int 32bit value. 1900 * Total number of short data pkt retries for the respective rate 1901 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG: Unsigned int 32bit value. 1902 * Total number of long data pkt retries for the respective rate 1903 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID: Radio id 1904 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME: Unsigned 32bit value. 1905 * Total number of msecs the radio is awake accruing over time 1906 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME: Unsigned 32bit value. 1907 * Total number of msecs the radio is transmitting accruing over time 1908 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME: Unsigned 32bit value. 1909 * Total number of msecs the radio is in active receive accruing over time 1910 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN: Unsigned 32bit value. 1911 * Total number of msecs the radio is awake due to all scan accruing 1912 * over time 1913 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD: Unsigned 32bit value. 1914 * Total number of msecs the radio is awake due to NAN accruing over time. 1915 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN: Unsigned 32bit value. 1916 * Total number of msecs the radio is awake due to GSCAN accruing over time 1917 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN: Unsigned 32bit value. 1918 * Total number of msecs the radio is awake due to roam scan accruing over 1919 * time. 1920 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN: Unsigned 32bit value. 1921 * Total number of msecs the radio is awake due to PNO scan accruing over 1922 * time. 1923 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20: Unsigned 32bit value. 1924 * Total number of msecs the radio is awake due to HS2.0 scans and GAS 1925 * exchange accruing over time. 1926 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS: Unsigned 32bit value. 1927 * Number of channels 1928 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH: 1929 * Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80, etc. 1930 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ: 1931 * Unsigned 32bit value. Primary 20MHz channel. 1932 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0: 1933 * Unsigned 32bit value. Center frequency (MHz) first segment. 1934 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1: 1935 * Unsigned 32bit value. Center frequency (MHz) second segment. 1936 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME: Unsigned int 32bit value 1937 * representing total number of msecs the radio is awake on that channel 1938 * accruing over time, corresponding to the respective channel. 1939 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME: Unsigned int 32bit 1940 * value representing total number of msecs the CCA register is busy 1941 * accruing over time corresponding to the respective channel. 1942 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS: Number of radios 1943 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO: Channel info 1944 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO: Peer info 1945 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO: Peer rate info 1946 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO: WMM info 1947 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA: Unsigned 8bit value. 1948 * Used by the driver; if set to 1, it indicates that more stats, e.g., 1949 * peers or radio, are to follow in the next 1950 * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. Otherwise, it 1951 * is set to 0. 1952 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET: tsf offset 1953 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED: leaky ap detected 1954 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED: 1955 * average number of frames leaked 1956 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME: guard time 1957 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE: Link Layer stats type 1958 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS: LL Radio Number of 1959 * Tx Levels 1960 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL:Number of msecs the 1961 * radio spent in transmitting for each power level 1962 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT: RTS successful count 1963 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT: RTS fail count 1964 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT: PPDU successful count 1965 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT: PPDU fail count 1966 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST: After last 1967 * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX: Max value 1968 */ 1969 1970 enum qca_wlan_vendor_attr_ll_stats_results { 1971 QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, 1972 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, 1973 1974 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, 1975 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, 1976 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, 1977 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, 1978 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, 1979 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, 1980 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, 1981 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, 1982 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, 1983 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, 1984 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, 1985 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, 1986 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, 1987 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, 1988 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, 1989 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, 1990 1991 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, 1992 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, 1993 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, 1994 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, 1995 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, 1996 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, 1997 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, 1998 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, 1999 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, 2000 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, 2001 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, 2002 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, 2003 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, 2004 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, 2005 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, 2006 2007 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, 2008 2009 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, 2010 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, 2011 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, 2012 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, 2013 2014 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, 2015 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, 2016 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, 2017 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, 2018 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, 2019 2020 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, 2021 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, 2022 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, 2023 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, 2024 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, 2025 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, 2026 2027 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, 2028 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, 2029 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, 2030 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, 2031 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, 2032 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, 2033 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, 2034 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, 2035 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, 2036 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, 2037 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, 2038 2039 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, 2040 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, 2041 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, 2042 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, 2043 2044 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, 2045 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, 2046 2047 QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, 2048 QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, 2049 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, 2050 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, 2051 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, 2052 2053 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, 2054 2055 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, 2056 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, 2057 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, 2058 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, 2059 2060 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, 2061 2062 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, 2063 2064 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, 2065 2066 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, 2067 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, 2068 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, 2069 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, 2070 2071 /* keep last */ 2072 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, 2073 QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = 2074 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1 2075 }; 2076 2077 enum qca_wlan_vendor_attr_ll_stats_type { 2078 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, 2079 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, 2080 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, 2081 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, 2082 2083 /* keep last */ 2084 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, 2085 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = 2086 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, 2087 }; 2088 2089 #endif /* WLAN_FEATURE_LINK_LAYER_STATS */ 2090 2091 /** 2092 * enum qca_wlan_vendor_attr_get_supported_features - get supported feature 2093 * 2094 * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_INVALID: Invalid initial value 2095 * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET: Unsigned 32bit value 2096 * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST: After last 2097 * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX: Max value 2098 */ 2099 enum qca_wlan_vendor_attr_get_supported_features { 2100 QCA_WLAN_VENDOR_ATTR_FEATURE_SET_INVALID = 0, 2101 QCA_WLAN_VENDOR_ATTR_FEATURE_SET = 1, 2102 QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST, 2103 QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX = 2104 QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST - 1, 2105 }; 2106 2107 /** 2108 * enum qca_wlan_vendor_attr_set_scanning_mac_oui - set scanning mac oui 2109 * 2110 * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_INVALID: Invalid initial value 2111 * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI: An array of 3 x Unsigned 8-bit 2112 * value 2113 * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST: After last 2114 * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_MAX: Max value 2115 */ 2116 enum qca_wlan_vendor_attr_set_scanning_mac_oui { 2117 QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_INVALID = 0, 2118 QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI = 1, 2119 QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST, 2120 QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_MAX = 2121 QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST - 1, 2122 }; 2123 2124 /** 2125 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes 2126 * 2127 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan 2128 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes 2129 * with frequencies to be scanned (in MHz) 2130 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned 2131 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported 2132 * rates to be included 2133 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests 2134 * at non CCK rate in 2GHz band 2135 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags 2136 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the 2137 * driver for the specific scan request 2138 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan 2139 * request decoded as in enum scan_status 2140 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation 2141 * scan flag is set 2142 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with 2143 * randomisation 2144 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: BSSID provided to do scan for specific BSS 2145 */ 2146 enum qca_wlan_vendor_attr_scan { 2147 QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, 2148 QCA_WLAN_VENDOR_ATTR_SCAN_IE, 2149 QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES, 2150 QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS, 2151 QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES, 2152 QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE, 2153 QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS, 2154 QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE, 2155 QCA_WLAN_VENDOR_ATTR_SCAN_STATUS, 2156 QCA_WLAN_VENDOR_ATTR_SCAN_MAC, 2157 QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK, 2158 QCA_WLAN_VENDOR_ATTR_SCAN_BSSID, 2159 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, 2160 QCA_WLAN_VENDOR_ATTR_SCAN_MAX = 2161 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 2162 }; 2163 2164 /** 2165 * enum scan_status - Specifies the valid values the vendor scan attribute 2166 * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take 2167 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with 2168 * new scan results 2169 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between 2170 */ 2171 enum scan_status { 2172 VENDOR_SCAN_STATUS_NEW_RESULTS, 2173 VENDOR_SCAN_STATUS_ABORTED, 2174 VENDOR_SCAN_STATUS_MAX, 2175 }; 2176 2177 /** 2178 * enum qca_wlan_vendor_attr_get_concurrency_matrix - get concurrency matrix 2179 * 2180 * NL attributes for data used by 2181 * QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX sub command. 2182 * 2183 * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_INVALID: Invalid initial value 2184 * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_CONFIG_PARAM_SET_SIZE_MAX: 2185 * Unsigned 32-bit value 2186 * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET_SIZE: 2187 * Unsigned 32-bit value 2188 * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET: Set results. An 2189 * array of SET_SIZE x Unsigned 32bit values representing concurrency 2190 * combinations 2191 * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST: After last 2192 * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_MAX: Max value 2193 */ 2194 enum qca_wlan_vendor_attr_get_concurrency_matrix { 2195 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_INVALID = 0, 2196 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_CONFIG_PARAM_SET_SIZE_MAX 2197 = 1, 2198 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET_SIZE = 2, 2199 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET = 3, 2200 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST, 2201 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_MAX = 2202 QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST - 1, 2203 }; 2204 2205 /** 2206 * enum qca_wlan_vendor_attr_set_no_dfs_flag - vendor attribute set no dfs flag 2207 * 2208 * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_INVALID: Invalid initial value 2209 * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG: Unsigned 32-bit value 2210 * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST: After last 2211 * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_MAX: Max value 2212 */ 2213 enum qca_wlan_vendor_attr_set_no_dfs_flag { 2214 QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_INVALID = 0, 2215 QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG = 1, 2216 QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST, 2217 QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_MAX = 2218 QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST - 1, 2219 }; 2220 2221 /** 2222 * enum qca_vendor_attr_wisa_cmd 2223 * @QCA_WLAN_VENDOR_ATTR_WISA_INVALID: Invalid attr 2224 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value attr (u32) 2225 * @QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST: After last 2226 * @QCA_WLAN_VENDOR_ATTR_WISA_MAX: Max Value 2227 * WISA setup vendor commands 2228 */ 2229 enum qca_vendor_attr_wisa_cmd { 2230 QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, 2231 QCA_WLAN_VENDOR_ATTR_WISA_MODE, 2232 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, 2233 QCA_WLAN_VENDOR_ATTR_WISA_MAX = 2234 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 2235 }; 2236 2237 enum qca_roaming_policy { 2238 QCA_ROAMING_NOT_ALLOWED, 2239 QCA_ROAMING_ALLOWED_WITHIN_ESS, 2240 }; 2241 2242 /** 2243 * enum qca_wlan_vendor_attr_roam_auth - vendor event for roaming 2244 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID: BSSID of the roamed AP 2245 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE: Request IE 2246 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE: Response IE 2247 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED: Authorization Status 2248 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR: Replay Counter 2249 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK: KCK of the PTK 2250 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK: KEK of the PTK 2251 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS: subnet change status 2252 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS: 2253 * Indicates the status of re-association requested by user space for 2254 * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. 2255 * Type u16. 2256 * Represents the status code from AP. Use 2257 * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the 2258 * real status code for failures. 2259 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION: 2260 * This attribute indicates that the old association was maintained when 2261 * a re-association is requested by user space and that re-association 2262 * attempt fails (i.e., cannot connect to the requested BSS, but can 2263 * remain associated with the BSS with which the association was in 2264 * place when being requested to roam). Used along with 2265 * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current 2266 * re-association status. Type flag. 2267 * This attribute is applicable only for re-association failure cases. 2268 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK: AUTH PMK 2269 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID: AUTH PMKID 2270 * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM: FILS erp next 2271 * seq number 2272 */ 2273 enum qca_wlan_vendor_attr_roam_auth { 2274 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, 2275 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, 2276 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, 2277 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, 2278 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, 2279 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, 2280 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, 2281 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, 2282 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, 2283 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, 2284 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, 2285 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK, 2286 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID, 2287 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM, 2288 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, 2289 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = 2290 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 2291 }; 2292 2293 /** 2294 * enum qca_wlan_vendor_attr_wifi_config - wifi config 2295 * 2296 * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_INVALID: Invalid initial value 2297 * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_DYNAMIC_DTIM: dynamic DTIM 2298 * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_STATS_AVG_FACTOR: avg factor 2299 * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_GUARD_TIME: guard time 2300 * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST: after last 2301 * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_MAX: max value 2302 */ 2303 enum qca_wlan_vendor_attr_wifi_config { 2304 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_INVALID = 0, 2305 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_DYNAMIC_DTIM = 1, 2306 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_STATS_AVG_FACTOR = 2, 2307 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_GUARD_TIME = 3, 2308 2309 /* keep last */ 2310 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST, 2311 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_MAX = 2312 QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST - 1, 2313 }; 2314 2315 /** 2316 * enum qca_wlan_epno_type - the type of request to the EPNO command 2317 * @QCA_WLAN_EPNO: epno type request 2318 * @QCA_WLAN_PNO: pno type request 2319 */ 2320 enum qca_wlan_epno_type { 2321 QCA_WLAN_EPNO, 2322 QCA_WLAN_PNO 2323 }; 2324 2325 /** 2326 * enum qca_wlan_vendor_attr_pno_config_params - pno config params 2327 * 2328 * @QCA_WLAN_VENDOR_ATTR_PNO_INVALID - Invalid initial value 2329 * 2330 * NL attributes for data used by 2331 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. 2332 * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM: 2333 * Unsigned 32-bit value; pno passpoint number of networks 2334 * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY: 2335 * Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* 2336 * attributes. Array size = 2337 * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. 2338 * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID: 2339 * Unsigned 32-bit value; network id 2340 * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM: 2341 * An array of 256 x Unsigned 8-bit value; NULL terminated UTF8 encoded 2342 * realm, 0 if unspecified. 2343 * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID: 2344 * An array of 16 x Unsigned 32-bit value; roaming consortium ids 2345 * to match, 0 if unspecified. 2346 * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN: 2347 * An array of 6 x Unsigned 8-bit value; mcc/mnc combination, 0s if 2348 * unspecified. 2349 * 2350 * NL attributes for data used by 2351 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. 2352 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS: 2353 * Unsigned 32-bit value; set pno number of networks 2354 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST: 2355 * Array of nested 2356 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* 2357 * attributes. Array size = 2358 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS 2359 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID: 2360 * An array of 33 x Unsigned 8-bit value; NULL terminated SSID 2361 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD: 2362 * Signed 8-bit value; threshold for considering this SSID as found, 2363 * required granularity for this threshold is 4dBm to 8dBm 2364 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS: 2365 * Unsigned 8-bit value; WIFI_PNO_FLAG_XXX 2366 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT: 2367 * Unsigned 8-bit value; auth bit field for matching WPA IE 2368 * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE 2369 * Unsigned 8-bit to indicate ePNO type; values from qca_wlan_epno_type 2370 *@QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST 2371 * Nested attribute to send the channel list 2372 *@QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL 2373 * Unsigned 32-bit value; indicates the Interval between PNO scan 2374 * cycles in msec 2375 *@QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI 2376 * Signed 32-bit value; minimum 5GHz RSSI for a BSSID to be considered 2377 *@QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI 2378 * Signed 32-bit value; minimum 2.4GHz RSSI for a BSSID to be considered 2379 * This attribute is obsolete now. 2380 *@QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX 2381 * Signed 32-bit value; the maximum score that a network 2382 * can have before bonuses 2383 *@QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS 2384 * Signed 32-bit value; only report when there is a network's 2385 * score this much higher han the current connection 2386 *@QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS 2387 * Signed 32-bit value; score bonus for all networks with 2388 * the same network flag 2389 *@QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS 2390 * Signed 32-bit value; score bonus for networks that are not open 2391 *@QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS 2392 * Signed 32-bit value; 5GHz RSSI score bonus applied to all 2393 * 5GHz networks 2394 *@QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID 2395 * Unsigned 32-bit value, representing the PNO Request ID 2396 * @QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST: After last 2397 * @QCA_WLAN_VENDOR_ATTR_PNO_MAX: max 2398 */ 2399 enum qca_wlan_vendor_attr_pno_config_params { 2400 QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, 2401 2402 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, 2403 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, 2404 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, 2405 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, 2406 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, 2407 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, 2408 2409 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, 2410 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, 2411 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, 2412 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD = 10, 2413 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, 2414 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, 2415 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, 2416 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, 2417 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, 2418 QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, 2419 QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, 2420 QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, 2421 QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, 2422 QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, 2423 QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, 2424 QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, 2425 2426 QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, 2427 /* keep last */ 2428 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, 2429 QCA_WLAN_VENDOR_ATTR_PNO_MAX = 2430 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, 2431 }; 2432 2433 /** 2434 * enum qca_wlan_vendor_attr_roaming_config_params - roaming config params 2435 * 2436 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID: Invalid initial value 2437 * @QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD: roaming sub command 2438 * @QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID: Request id 2439 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS: 2440 * number of whitelist networks 2441 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST: 2442 * Whitelist ssid list 2443 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID: 2444 * white list ssid 2445 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD: 2446 * 'a' band boost threshold 2447 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD: 2448 * 'a' band penalty threshold 2449 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR: 2450 * 'a' band boost factor 2451 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR: 2452 * 'a' band penalty factor 2453 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST: 2454 * 'a' band max boost 2455 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS: 2456 * lazy roam histeresys 2457 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER: 2458 * alert roam rssi trigger 2459 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE: 2460 * set lazy roam enable 2461 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS: 2462 * set bssid preference 2463 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID: 2464 * set lazy roam number of bssid 2465 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID: 2466 * set lazy roam bssid 2467 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER: 2468 * set lazy roam rssi modifier 2469 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: 2470 * set bssid params 2471 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: 2472 * set bssid params num bssid 2473 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: 2474 * set bssid params bssid 2475 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST: After last 2476 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX: Max 2477 */ 2478 enum qca_wlan_vendor_attr_roaming_config_params { 2479 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, 2480 2481 QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, 2482 QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, 2483 2484 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, 2485 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, 2486 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, 2487 2488 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, 2489 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, 2490 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, 2491 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, 2492 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, 2493 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, 2494 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, 2495 2496 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, 2497 2498 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, 2499 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, 2500 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, 2501 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, 2502 2503 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, 2504 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, 2505 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, 2506 2507 /* keep last */ 2508 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, 2509 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = 2510 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, 2511 }; 2512 2513 /** 2514 * enum qca_wlan_vendor_attr_roam_subcmd - roam sub commands 2515 * 2516 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID: Invalid initial value 2517 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST: ssid white list 2518 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_EXTSCAN_ROAM_PARAMS: roam params 2519 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM: set lazy roam 2520 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS: set bssid prefs 2521 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS: set bssid params 2522 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID: set blacklist bssid 2523 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST: after last 2524 * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX: subcmd max 2525 */ 2526 enum qca_wlan_vendor_attr_roam_subcmd { 2527 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0, 2528 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1, 2529 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_EXTSCAN_ROAM_PARAMS = 2, 2530 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3, 2531 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4, 2532 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5, 2533 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6, 2534 2535 /* KEEP LAST */ 2536 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST, 2537 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX = 2538 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1, 2539 }; 2540 2541 /** 2542 * enum qca_wlan_vendor_attr_get_wifi_info - wifi driver information 2543 * 2544 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID: Invalid initial value 2545 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION: get host driver version 2546 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION: ger firmware version 2547 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX - get radio index 2548 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST: after last 2549 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX: subcmd max 2550 */ 2551 enum qca_wlan_vendor_attr_get_wifi_info { 2552 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, 2553 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, 2554 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, 2555 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX = 3, 2556 2557 /* KEEP LAST */ 2558 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, 2559 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = 2560 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, 2561 }; 2562 2563 enum qca_wlan_vendor_attr_logger_results { 2564 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, 2565 2566 /* 2567 * Unsigned 32-bit value; must match the request Id supplied by 2568 * Wi-Fi HAL in the corresponding subcmd NL msg. 2569 */ 2570 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, 2571 2572 /* 2573 * Unsigned 32-bit value; used to indicate the size of memory 2574 * dump to be allocated. 2575 */ 2576 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, 2577 2578 /* keep last */ 2579 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, 2580 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = 2581 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, 2582 }; 2583 2584 /** 2585 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. 2586 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. 2587 */ 2588 enum qca_wlan_vendor_channel_prop_flags { 2589 /* Bits 0, 1, 2, and 3 are reserved */ 2590 2591 /* Turbo channel */ 2592 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, 2593 /* CCK channel */ 2594 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, 2595 /* OFDM channel */ 2596 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, 2597 /* 2.4 GHz spectrum channel. */ 2598 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, 2599 /* 5 GHz spectrum channel */ 2600 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, 2601 /* Only passive scan allowed */ 2602 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, 2603 /* Dynamic CCK-OFDM channel */ 2604 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, 2605 /* GFSK channel (FHSS PHY) */ 2606 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, 2607 /* Radar found on channel */ 2608 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, 2609 /* 11a static turbo channel only */ 2610 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, 2611 /* Half rate channel */ 2612 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, 2613 /* Quarter rate channel */ 2614 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, 2615 /* HT 20 channel */ 2616 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, 2617 /* HT 40 with extension channel above */ 2618 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, 2619 /* HT 40 with extension channel below */ 2620 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, 2621 /* HT 40 intolerant */ 2622 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, 2623 /* VHT 20 channel */ 2624 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, 2625 /* VHT 40 with extension channel above */ 2626 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, 2627 /* VHT 40 with extension channel below */ 2628 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, 2629 /* VHT 80 channel */ 2630 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, 2631 /* HT 40 intolerant mark bit for ACS use */ 2632 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, 2633 /* Channel temporarily blocked due to noise */ 2634 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, 2635 /* VHT 160 channel */ 2636 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, 2637 /* VHT 80+80 channel */ 2638 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, 2639 /* HE 20 channel */ 2640 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, 2641 /* HE 40 with extension channel above */ 2642 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, 2643 /* HE 40 with extension channel below */ 2644 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, 2645 /* HE 40 intolerant */ 2646 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31, 2647 }; 2648 2649 /** 2650 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a 2651 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is 2652 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. 2653 */ 2654 enum qca_wlan_vendor_channel_prop_flags_2 { 2655 /* HE 40 intolerant mark bit for ACS use */ 2656 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, 2657 /* HE 80 channel */ 2658 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, 2659 /* HE 160 channel */ 2660 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, 2661 /* HE 80+80 channel */ 2662 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, 2663 }; 2664 2665 /** 2666 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for 2667 * each channel. This is used by 2668 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. 2669 */ 2670 enum qca_wlan_vendor_channel_prop_flags_ext { 2671 /* Radar found on channel */ 2672 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, 2673 /* DFS required on channel */ 2674 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, 2675 /* DFS required on channel for 2nd band of 80+80 */ 2676 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, 2677 /* If channel has been checked for DFS */ 2678 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, 2679 /* Excluded in 802.11d */ 2680 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, 2681 /* Channel Switch Announcement received on this channel */ 2682 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, 2683 /* Ad-hoc is not allowed */ 2684 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, 2685 /* Station only channel */ 2686 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, 2687 /* DFS radar history for slave device (STA mode) */ 2688 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, 2689 /* DFS CAC valid for slave device (STA mode) */ 2690 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, 2691 }; 2692 2693 /** 2694 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd 2695 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite 2696 * information to start/stop the NUD statistics collection. 2697 */ 2698 enum qca_attr_nud_stats_set { 2699 QCA_ATTR_NUD_STATS_SET_INVALID = 0, 2700 2701 /* 2702 * Flag to start/stop the NUD statistics collection. 2703 * Start - If included, Stop - If not included 2704 */ 2705 QCA_ATTR_NUD_STATS_SET_START = 1, 2706 /* IPv4 address of the default gateway (in network byte order) */ 2707 QCA_ATTR_NUD_STATS_GW_IPV4 = 2, 2708 /* 2709 * Represents the data packet type to be monitored. 2710 * Host driver tracks the stats corresponding to each data frame 2711 * represented by these flags. 2712 * These data packets are represented by 2713 * enum qca_wlan_vendor_nud_stats_set_data_pkt_info. 2714 */ 2715 QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, 2716 /* keep last */ 2717 QCA_ATTR_NUD_STATS_SET_LAST, 2718 QCA_ATTR_NUD_STATS_SET_MAX = 2719 QCA_ATTR_NUD_STATS_SET_LAST - 1, 2720 }; 2721 2722 /** 2723 * enum qca_attr_connectivity_check_stats_set - attribute to vendor subcmd 2724 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite 2725 * information to start / stop the NUD stats collection. 2726 * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_STATS_PKT_INFO_TYPE: set pkt info stats 2727 * Bitmap to Flag to Start / Stop the NUD stats collection 2728 * Start - If included , Stop - If not included 2729 * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DNS_DOMAIN_NAME: set gatway ipv4 address 2730 * IPv4 address of Default Gateway (in network byte order) 2731 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite 2732 * information to start / stop the NUD stats collection. 2733 * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_SRC_PORT: set nud debug stats 2734 * Flag to Start / Stop the NUD stats collection 2735 * Start - If included , Stop - If not included 2736 * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_PORT: set gatway ipv4 address 2737 * IPv4 address of Default Gateway (in network byte order) 2738 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite 2739 * information to start / stop the NUD stats collection. 2740 * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV4: set nud debug stats 2741 * Flag to Start / Stop the NUD stats collection 2742 * Start - If included , Stop - If not included 2743 * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV6: set gatway ipv4 address 2744 * IPv4 address of Default Gateway (in network byte order) 2745 */ 2746 enum qca_attr_connectivity_check_stats_set { 2747 QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_INVALID = 0, 2748 QCA_ATTR_CONNECTIVITY_CHECK_STATS_STATS_PKT_INFO_TYPE = 1, 2749 QCA_ATTR_CONNECTIVITY_CHECK_STATS_DNS_DOMAIN_NAME = 2, 2750 QCA_ATTR_CONNECTIVITY_CHECK_STATS_SRC_PORT = 3, 2751 QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_PORT = 4, 2752 QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV4 = 5, 2753 QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV6 = 6, 2754 /* keep last */ 2755 QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_LAST, 2756 QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_MAX = 2757 QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_LAST - 1, 2758 }; 2759 2760 /** 2761 * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various 2762 * data types for which the stats have to get collected. 2763 */ 2764 enum qca_wlan_vendor_connectivity_check_pkt_flags { 2765 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ARP = 1 << 0, 2766 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_DNS = 1 << 1, 2767 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_HANDSHAKE = 1 << 2, 2768 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ICMPV4 = 1 << 3, 2769 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ICMPV6 = 1 << 4, 2770 /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get 2771 * to represent the stats of respective data type. 2772 */ 2773 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_SYN = 1 << 5, 2774 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_SYN_ACK = 1 << 6, 2775 QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_ACK = 1 << 7, 2776 }; 2777 2778 enum qca_attr_connectivity_check_stats { 2779 QCA_ATTR_CONNECTIVITY_CHECK_STATS_INVALID = 0, 2780 /* Data packet type for which the stats are collected. 2781 * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags 2782 */ 2783 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_TYPE = 1, 2784 /* ID corresponding to the DNS frame for which the respective DNS stats 2785 * are monitored (u32). 2786 */ 2787 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DNS_DOMAIN_NAME = 2, 2788 /* source / destination port on which the respective proto stats are 2789 * collected (u32). 2790 */ 2791 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_SRC_PORT = 3, 2792 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_PORT = 4, 2793 /* IPv4/IPv6 address for which the destined data packets are 2794 * monitored. (in network byte order) 2795 */ 2796 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_IPV4 = 5, 2797 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_IPV6 = 6, 2798 /* Data packet Request count received from netdev */ 2799 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, 2800 /* Data packet Request count sent to lower MAC from upper MAC */ 2801 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, 2802 /* Data packet Request count received by lower MAC from upper MAC */ 2803 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, 2804 /* Data packet Request count successfully transmitted by the device */ 2805 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, 2806 /* Data packet Response count received by lower MAC */ 2807 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, 2808 /* Data packet Response count received by upper MAC */ 2809 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, 2810 /* Data packet Response count delivered to netdev */ 2811 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, 2812 /* Data Packet Response count that are dropped out of order */ 2813 QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, 2814 2815 /* keep last */ 2816 QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_LAST, 2817 QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_MAX = 2818 QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_LAST - 1, 2819 }; 2820 2821 /** 2822 * qca_attr_nud_stats_get: Attributes to vendor subcmd 2823 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite 2824 * NUD statistics collected when queried. 2825 */ 2826 enum qca_attr_nud_stats_get { 2827 QCA_ATTR_NUD_STATS_GET_INVALID = 0, 2828 /* ARP Request count from netdev */ 2829 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, 2830 /* ARP Request count sent to lower MAC from upper MAC */ 2831 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, 2832 /* ARP Request count received by lower MAC from upper MAC */ 2833 QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, 2834 /* ARP Request count successfully transmitted by the device */ 2835 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, 2836 /* ARP Response count received by lower MAC */ 2837 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, 2838 /* ARP Response count received by upper MAC */ 2839 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, 2840 /* ARP Response count delivered to netdev */ 2841 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, 2842 /* ARP Response count delivered to netdev */ 2843 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, 2844 /* 2845 * Flag indicating if the station's link to the AP is active. 2846 * Active Link - If included, Inactive link - If not included 2847 */ 2848 QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, 2849 /* 2850 * Flag indicating if there is any duplicate address detected (DAD). 2851 * Yes - If detected, No - If not detected. 2852 */ 2853 QCA_ATTR_NUD_STATS_IS_DAD = 10, 2854 /* 2855 * List of Data types for which the stats are requested. 2856 * This list does not carry ARP stats as they are done by the 2857 * above attributes. Represented by enum qca_attr_nud_data_stats. 2858 */ 2859 QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, 2860 /* keep last */ 2861 QCA_ATTR_NUD_STATS_GET_LAST, 2862 QCA_ATTR_NUD_STATS_GET_MAX = 2863 QCA_ATTR_NUD_STATS_GET_LAST - 1, 2864 }; 2865 2866 enum qca_wlan_btm_candidate_status { 2867 QCA_STATUS_ACCEPT = 0, 2868 QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, 2869 QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, 2870 QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, 2871 QCA_STATUS_REJECT_LOW_RSSI = 4, 2872 QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, 2873 QCA_STATUS_REJECT_UNKNOWN = 6, 2874 }; 2875 2876 enum qca_wlan_vendor_attr_btm_candidate_info { 2877 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, 2878 2879 /* 6-byte MAC address representing the BSSID of transition candidate */ 2880 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, 2881 /* 2882 * Unsigned 32-bit value from enum qca_wlan_btm_candidate_status 2883 * returned by the driver. It says whether the BSSID provided in 2884 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by 2885 * the driver, if not it specifies the reason for rejection. 2886 * Note that the user-space can overwrite the transition reject reason 2887 * codes provided by driver based on more information. 2888 */ 2889 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, 2890 2891 /* keep last */ 2892 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, 2893 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = 2894 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, 2895 }; 2896 2897 enum qca_attr_trace_level { 2898 QCA_ATTR_TRACE_LEVEL_INVALID = 0, 2899 /* 2900 * Nested array of the following attributes: 2901 * QCA_ATTR_TRACE_LEVEL_MODULE, 2902 * QCA_ATTR_TRACE_LEVEL_MASK. 2903 */ 2904 QCA_ATTR_TRACE_LEVEL_PARAM = 1, 2905 /* 2906 * Specific QCA host driver module. Please refer to the QCA host 2907 * driver implementation to get the specific module ID. 2908 */ 2909 QCA_ATTR_TRACE_LEVEL_MODULE = 2, 2910 /* Different trace level masks represented in the QCA host driver. */ 2911 QCA_ATTR_TRACE_LEVEL_MASK = 3, 2912 2913 /* keep last */ 2914 QCA_ATTR_TRACE_LEVEL_AFTER_LAST, 2915 QCA_ATTR_TRACE_LEVEL_MAX = 2916 QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, 2917 }; 2918 2919 /** 2920 * enum qca_wlan_vendor_attr_get_logger_features - value for logger 2921 * supported features 2922 * @QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID - Invalid 2923 * @QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED - Indicate the supported features 2924 * @QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - To keep track of the last enum 2925 * @QCA_WLAN_VENDOR_ATTR_LOGGER_MAX - max value possible for this type 2926 * 2927 * enum values are used for NL attributes for data used by 2928 * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET sub command. 2929 */ 2930 enum qca_wlan_vendor_attr_get_logger_features { 2931 QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, 2932 QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, 2933 2934 /* keep last */ 2935 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, 2936 QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = 2937 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, 2938 }; 2939 2940 /** 2941 * enum qca_wlan_vendor_attr_link_properties - link properties 2942 * 2943 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID: Invalid initial value 2944 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_NSS: Unsigned 8-bit value to 2945 * specify the number of spatial streams negotiated 2946 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_RATE_FLAGS: Unsigned 8-bit value 2947 * to specify negotiated rate flags i.e. ht, vht and channel width 2948 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_FREQ: Unsigned 32bit value to 2949 * specify the operating frequency 2950 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC Address of the peer 2951 * (STA / AP ) for the connected link. 2952 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a 2953 * &struct nl80211_sta_flag_update for the respective connected link. MAC 2954 * address of the peer represented by 2955 * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. 2956 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST: after last 2957 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAX: max value 2958 */ 2959 enum qca_wlan_vendor_attr_link_properties { 2960 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, 2961 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_NSS = 1, 2962 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_RATE_FLAGS = 2, 2963 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_FREQ = 3, 2964 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, 2965 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, 2966 2967 /* KEEP LAST */ 2968 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, 2969 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAX = 2970 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, 2971 }; 2972 2973 /** 2974 * enum qca_wlan_vendor_attr_nd_offload - vendor NS offload support 2975 * 2976 * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID - Invalid 2977 * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG - Flag to set NS offload 2978 * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - To keep track of the last enum 2979 * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX - max value possible for this type 2980 * 2981 * enum values are used for NL attributes for data used by 2982 * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD sub command. 2983 */ 2984 enum qca_wlan_vendor_attr_nd_offload { 2985 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, 2986 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, 2987 2988 /* Keep last */ 2989 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, 2990 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = 2991 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, 2992 }; 2993 2994 /** 2995 * enum qca_wlan_vendor_features - vendor device/driver features 2996 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key 2997 * management offload, a mechanism where the station's firmware 2998 * does the exchange with the AP to establish the temporal keys 2999 * after roaming, rather than having the supplicant do it. 3000 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports 3001 * simultaneous off-channel operations. 3002 * @QQCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P 3003 * Listen offload; a mechanism where the station's firmware 3004 * takes care of responding to incoming Probe Request frames received 3005 * from other P2P devices whilst in Listen state, rather than having the 3006 * user space wpa_supplicant do it. Information from received P2P 3007 * Requests are forwarded from firmware to host whenever the APPS 3008 * processor exits power collapse state. 3009 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA 3010 * specific features 3011 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific 3012 * features. 3013 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON 3014 * specific features only. If a Device sets this bit but not the 3015 * QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that 3016 * this Device may not support all OCE AP functionalities but can support 3017 * only OCE STA-CFON functionalities. 3018 * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self 3019 * managed regulatory. 3020 */ 3021 enum qca_wlan_vendor_features { 3022 QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, 3023 QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, 3024 QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, 3025 QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, 3026 QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, 3027 QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, 3028 QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, 3029 QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, 3030 /* Additional features need to be added above this */ 3031 NUM_QCA_WLAN_VENDOR_FEATURES 3032 }; 3033 3034 /** 3035 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for SAP 3036 * conditional channel switch 3037 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID: Invalid initial 3038 * value 3039 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST: Priority based 3040 * frequency list (an array of u32 values in host byte order) 3041 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS: Status of the 3042 * conditional switch (u32)- 0: Success, Non-zero: Failure 3043 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST: After last 3044 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX: Subcommand max 3045 */ 3046 enum qca_wlan_vendor_attr_sap_conditional_chan_switch { 3047 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, 3048 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, 3049 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, 3050 3051 /* Keep Last */ 3052 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, 3053 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = 3054 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, 3055 }; 3056 3057 /** 3058 * enum wifi_logger_supported_features - values for supported logger features 3059 * @WIFI_LOGGER_MEMORY_DUMP_SUPPORTED: Memory dump of FW 3060 * @WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_SUPPORTED: Per packet statistics 3061 * @WIFI_LOGGER_CONNECT_EVENT_SUPPORTED: Logging of Connectivity events 3062 * @WIFI_LOGGER_POWER_EVENT_SUPPORTED: Power of driver 3063 * @WIFI_LOGGER_WAKE_LOCK_SUPPORTE: Wakelock of driver 3064 * @WIFI_LOGGER_WATCHDOG_TIMER_SUPPORTED: monitor FW health 3065 * @WIFI_LOGGER_DRIVER_DUMP_SUPPORTED: support driver dump 3066 * @WIFI_LOGGER_PACKET_FATE_SUPPORTED: tracks connection packets fate 3067 */ 3068 enum wifi_logger_supported_features { 3069 WIFI_LOGGER_MEMORY_DUMP_SUPPORTED = (1 << (0)), 3070 WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_SUPPORTED = (1 << (1)), 3071 WIFI_LOGGER_CONNECT_EVENT_SUPPORTED = (1 << (2)), 3072 WIFI_LOGGER_POWER_EVENT_SUPPORTED = (1 << (3)), 3073 WIFI_LOGGER_WAKE_LOCK_SUPPORTED = (1 << (4)), 3074 WIFI_LOGGER_VERBOSE_SUPPORTED = (1 << (5)), 3075 WIFI_LOGGER_WATCHDOG_TIMER_SUPPORTED = (1 << (6)), 3076 WIFI_LOGGER_DRIVER_DUMP_SUPPORTED = (1 << (7)), 3077 WIFI_LOGGER_PACKET_FATE_SUPPORTED = (1 << (8)) 3078 }; 3079 /** 3080 * enum qca_wlan_vendor_attr_acs_offload 3081 * 3082 * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL: ACS selected primary channel 3083 * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL: ACS selected secondary channel 3084 * @QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE: hw_mode for ACS 3085 * @QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED: indicate if HT capability is enabled 3086 * @QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED: indicate HT capability 3087 */ 3088 enum qca_wlan_vendor_attr_acs_offload { 3089 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, 3090 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL, 3091 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL, 3092 QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE, 3093 QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED, 3094 QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED, 3095 QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED, 3096 QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH, 3097 QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST, 3098 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL, 3099 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL, 3100 QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST, 3101 /* keep last */ 3102 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, 3103 QCA_WLAN_VENDOR_ATTR_ACS_MAX = 3104 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 3105 }; 3106 3107 /** 3108 * enum qca_wlan_vendor_acs_hw_mode 3109 * 3110 * @QCA_ACS_MODE_IEEE80211B: 11b mode 3111 * @QCA_ACS_MODE_IEEE80211G: 11g mode 3112 * @QCA_ACS_MODE_IEEE80211A: 11a mode 3113 * @QCA_ACS_MODE_IEEE80211AD: 11ad mode 3114 */ 3115 enum qca_wlan_vendor_acs_hw_mode { 3116 QCA_ACS_MODE_IEEE80211B, 3117 QCA_ACS_MODE_IEEE80211G, 3118 QCA_ACS_MODE_IEEE80211A, 3119 QCA_ACS_MODE_IEEE80211AD, 3120 QCA_ACS_MODE_IEEE80211ANY, 3121 }; 3122 3123 /** 3124 * enum qca_access_policy - access control policy 3125 * 3126 * Access control policy is applied on the configured IE 3127 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). 3128 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. 3129 * 3130 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi Connections which match 3131 *» with the specific configuration (IE) set, i.e. allow all the 3132 *» connections which do not match the configuration. 3133 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi Connections which match 3134 *» with the specific configuration (IE) set, i.e. deny all the 3135 *» connections which do not match the configuration. 3136 */ 3137 enum qca_access_policy { 3138 QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, 3139 QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, 3140 }; 3141 3142 /** 3143 * enum qca_ignore_assoc_disallowed - Ignore assoc disallowed values 3144 * 3145 * The valid values for the ignore assoc disallowed 3146 * 3147 * @QCA_IGNORE_ASSOC_DISALLOWED_DISABLE: Disable ignore assoc disallowed 3148 * @QCA_IGNORE_ASSOC_DISALLOWED_ENABLE: Enable ignore assoc disallowed 3149 * 3150 */ 3151 enum qca_ignore_assoc_disallowed { 3152 QCA_IGNORE_ASSOC_DISALLOWED_DISABLE, 3153 QCA_IGNORE_ASSOC_DISALLOWED_ENABLE 3154 }; 3155 3156 /* Attributes for data used by 3157 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and 3158 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. 3159 */ 3160 enum qca_wlan_vendor_attr_config { 3161 QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, 3162 /* 3163 * Unsigned 32-bit value to set the DTIM period. 3164 * Whether the wifi chipset wakes at every dtim beacon or a multiple of 3165 * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 3166 * DTIM beacons. 3167 */ 3168 QCA_WLAN_VENDOR_ATTR_CONFIG_MODULATED_DTIM = 1, 3169 /* 3170 * Unsigned 32-bit value to set the wifi_iface stats averaging factor 3171 * used to calculate statistics like average the TSF offset or average 3172 * number of frame leaked. 3173 * For instance, upon Beacon frame reception: 3174 * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 3175 * For instance, when evaluating leaky APs: 3176 * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 3177 */ 3178 QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, 3179 /* 3180 * Unsigned 32-bit value to configure guard time, i.e., when 3181 * implementing IEEE power management based on frame control PM bit, how 3182 * long the driver waits before shutting down the radio and after 3183 * receiving an ACK frame for a Data frame with PM bit set. 3184 */ 3185 QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, 3186 /* Unsigned 32-bit value to change the FTM capability dynamically */ 3187 QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, 3188 /* Unsigned 16-bit value to configure maximum TX rate dynamically */ 3189 QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, 3190 /* 3191 * Unsigned 32-bit value to configure the number of continuous 3192 * Beacon Miss which shall be used by the firmware to penalize 3193 * the RSSI. 3194 */ 3195 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, 3196 /* 3197 * Unsigned 8-bit value to configure the channel avoidance indication 3198 * behavior. Firmware to send only one indication and ignore duplicate 3199 * indications when set to avoid multiple Apps wakeups. 3200 */ 3201 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, 3202 /* 3203 * 8-bit unsigned value to configure the maximum TX MPDU for 3204 * aggregation. 3205 */ 3206 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, 3207 /* 3208 * 8-bit unsigned value to configure the maximum RX MPDU for 3209 * aggregation. 3210 */ 3211 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, 3212 /* 3213 * 8-bit unsigned value to configure the Non aggregrate/11g sw 3214 * retry threshold (0 disable, 31 max). 3215 */ 3216 QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, 3217 /* 3218 * 8-bit unsigned value to configure the aggregrate sw 3219 * retry threshold (0 disable, 31 max). 3220 */ 3221 QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, 3222 /* 3223 * 8-bit unsigned value to configure the MGMT frame 3224 * retry threshold (0 disable, 31 max). 3225 */ 3226 QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, 3227 /* 3228 * 8-bit unsigned value to configure the CTRL frame 3229 * retry threshold (0 disable, 31 max). 3230 */ 3231 QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, 3232 /* 3233 * 8-bit unsigned value to configure the propagation delay for 3234 * 2G/5G band (0~63, units in us) 3235 */ 3236 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, 3237 /* 3238 * Unsigned 32-bit value to configure the number of unicast TX fail 3239 * packet count. The peer is disconnected once this threshold is 3240 * reached. 3241 */ 3242 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, 3243 /* 3244 * Attribute used to set scan default IEs to the driver. 3245 * 3246 * These IEs can be used by scan operations that will be initiated by 3247 * the driver/firmware. 3248 * 3249 * For further scan requests coming to the driver, these IEs should be 3250 * merged with the IEs received along with scan request coming to the 3251 * driver. If a particular IE is present in the scan default IEs but not 3252 * present in the scan request, then that IE should be added to the IEs 3253 * sent in the Probe Request frames for that scan request. 3254 */ 3255 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, 3256 /* Unsigned 32-bit attribute for generic commands */ 3257 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, 3258 /* Unsigned 32-bit value attribute for generic commands */ 3259 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, 3260 /* Unsigned 32-bit data attribute for generic command response */ 3261 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, 3262 /* 3263 * Unsigned 32-bit length attribute for 3264 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA 3265 */ 3266 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, 3267 /* 3268 * Unsigned 32-bit flags attribute for 3269 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA 3270 */ 3271 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, 3272 /* 3273 * Unsigned 32-bit, defining the access policy. 3274 * See enum qca_access_policy. Used with 3275 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. 3276 */ 3277 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, 3278 /* 3279 * Sets the list of full set of IEs for which a specific access policy 3280 * has to be applied. Used along with 3281 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. 3282 * Zero length payload can be used to clear this access constraint. 3283 */ 3284 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, 3285 /* 3286 * Unsigned 32-bit, specifies the interface index (netdev) for which the 3287 * corresponding configurations are applied. If the interface index is 3288 * not specified, the configurations are attributed to the respective 3289 * wiphy. 3290 */ 3291 QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, 3292 /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ 3293 QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, 3294 /* 3295 * 8-bit unsigned value to configure the driver and below layers to 3296 * ignore the assoc disallowed set by APs while connecting 3297 * 1-Ignore, 0-Don't ignore 3298 */ 3299 QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, 3300 /* 3301 * 32-bit unsigned value to trigger antenna diversity features: 3302 * 1-Enable, 0-Disable 3303 */ 3304 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, 3305 /* 32-bit unsigned value to configure specific chain antenna */ 3306 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, 3307 /* 3308 * 32-bit unsigned value to trigger cycle selftest 3309 * 1-Enable, 0-Disable 3310 */ 3311 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, 3312 /* 3313 * 32-bit unsigned to configure the cycle time of selftest 3314 * the unit is micro-second 3315 */ 3316 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, 3317 /* 32-bit unsigned value to set reorder timeout for AC_VO */ 3318 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, 3319 /* 32-bit unsigned value to set reorder timeout for AC_VI */ 3320 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, 3321 /* 32-bit unsigned value to set reorder timeout for AC_BE */ 3322 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, 3323 /* 32-bit unsigned value to set reorder timeout for AC_BK */ 3324 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, 3325 /* 6-byte MAC address to point out the specific peer */ 3326 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, 3327 /* 32-bit unsigned value to set window size for specific peer */ 3328 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, 3329 /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ 3330 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, 3331 /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ 3332 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, 3333 /* 3334 * 32-bit unsigned value to configure 5 or 10 MHz channel width for 3335 * station device while in disconnect state. The attribute use the 3336 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, 3337 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or 3338 * 10 MHz channel width, the station will not connect to a BSS using 20 3339 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to 3340 * clear this constraint. 3341 */ 3342 QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, 3343 /* 3344 * 32-bit unsigned value to configure the propagation absolute delay 3345 * for 2G/5G band (units in us) 3346 */ 3347 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, 3348 /* 32-bit unsigned value to set probe period */ 3349 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, 3350 /* 32-bit unsigned value to set stay period */ 3351 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, 3352 /* 32-bit unsigned value to set snr diff */ 3353 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, 3354 /* 32-bit unsigned value to set probe dwell time */ 3355 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, 3356 /* 32-bit unsigned value to set mgmt snr weight */ 3357 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, 3358 /* 32-bit unsigned value to set data snr weight */ 3359 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, 3360 /* 32-bit unsigned value to set ack snr weight */ 3361 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, 3362 /* 3363 * 32-bit unsigned value to configure the listen interval. 3364 * This is in units of beacon intervals. This configuration alters 3365 * the negotiated listen interval with the AP during the connection. 3366 * It is highly recommended to configure a value less than or equal to 3367 * the one negotiated during the association. Configuring any greater 3368 * value can have adverse effects (frame loss, AP disassociating STA, 3369 * etc.). 3370 */ 3371 QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, 3372 /* 3373 * 8 bit unsigned value that is set on an AP/GO virtual interface to 3374 * disable operations that would cause the AP/GO to leave its operating 3375 * channel. 3376 * 3377 * This will restrict the scans to the AP/GO operating channel and the 3378 * channels of the other band, if DBS is supported.A STA/CLI interface 3379 * brought up after this setting is enabled, will be restricted to 3380 * connecting to devices only on the AP/GO interface's operating channel 3381 * or on the other band in DBS case. P2P supported channel list is 3382 * modified, to only include AP interface's operating-channel and the 3383 * channels of the other band if DBS is supported. 3384 * 3385 * These restrictions are only applicable as long as the AP/GO interface 3386 * is alive. If the AP/GO interface is brought down then this 3387 * setting/restriction is forgotten. 3388 * 3389 * If this variable is set on an AP/GO interface while a multi-channel 3390 * concurrent session is active, it has no effect on the operation of 3391 * the current interfaces, other than restricting the scan to the AP/GO 3392 * operating channel and the other band channels if DBS is supported. 3393 * However, if the STA is brought down and restarted then the new STA 3394 * connection will either be formed on the AP/GO channel or on the 3395 * other band in a DBS case. This is because of the scan being 3396 * restricted on these channels as mentioned above. 3397 * 3398 * 1-Disable offchannel operations, 0-Enable offchannel operations. 3399 */ 3400 QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, 3401 3402 /* 3403 * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) 3404 * on an interface. 3405 * 1 - Enable , 0 - Disable. 3406 */ 3407 QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, 3408 3409 /* 3410 * 8 bit unsigned value to globally enable/disable scan 3411 * 1 - Enable, 0 - Disable. 3412 */ 3413 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, 3414 3415 /* 8-bit unsigned value to set the total beacon miss count */ 3416 QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, 3417 3418 /* 3419 * Unsigned 32-bit value to configure the number of continuous 3420 * Beacon Miss which shall be used by the firmware to penalize 3421 * the RSSI for BTC. 3422 */ 3423 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, 3424 3425 /* 3426 * 8-bit unsigned value to configure the driver and below layers to 3427 * enable/disable all fils features. 3428 * 0-enable, 1-disable 3429 */ 3430 QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, 3431 3432 /* 16-bit unsigned value to configure the level of WLAN latency 3433 * module. See enum qca_wlan_vendor_attr_config_latency_level. 3434 */ 3435 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, 3436 3437 /* 3438 * 8-bit unsigned value indicating the driver to use the RSNE as-is from 3439 * the connect interface. Exclusively used for the scenarios where the 3440 * device is used as a test bed device with special functionality and 3441 * not recommended for production. This helps driver to not validate the 3442 * RSNE passed from user space and thus allow arbitrary IE data to be 3443 * used for testing purposes. 3444 * 1-enable, 0-disable. 3445 * Applications set/reset this configuration. If not reset, this 3446 * parameter remains in use until the driver is unloaded. 3447 */ 3448 QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, 3449 3450 /* 3451 * 8-bit unsigned value to trigger green Tx power saving. 3452 * 1-Enable, 0-Disable 3453 */ 3454 QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, 3455 3456 /* keep last */ 3457 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, 3458 QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = 3459 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, 3460 }; 3461 3462 /** 3463 * enum qca_wlan_vendor_attr_wifi_logger_start - Enum for wifi logger starting 3464 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID: Invalid attribute 3465 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID: Ring ID 3466 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL: Verbose level 3467 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS: Flag 3468 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST: Last value 3469 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_MAX: Max value 3470 */ 3471 enum qca_wlan_vendor_attr_wifi_logger_start { 3472 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, 3473 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, 3474 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, 3475 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, 3476 /* keep last */ 3477 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, 3478 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_MAX = 3479 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, 3480 }; 3481 3482 /* 3483 * enum qca_wlan_vendor_attr_wifi_logger_get_ring_data - Get ring data 3484 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_INVALID: Invalid attribute 3485 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_ID: Ring ID 3486 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST: Last value 3487 * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_MAX: Max value 3488 */ 3489 enum qca_wlan_vendor_attr_wifi_logger_get_ring_data { 3490 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_INVALID = 0, 3491 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_ID = 1, 3492 /* keep last */ 3493 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST, 3494 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_MAX = 3495 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST - 1, 3496 }; 3497 3498 #ifdef WLAN_FEATURE_OFFLOAD_PACKETS 3499 /** 3500 * enum wlan_offloaded_packets_control - control commands 3501 * @WLAN_START_OFFLOADED_PACKETS: start offloaded packets 3502 * @WLAN_STOP_OFFLOADED_PACKETS: stop offloaded packets 3503 * 3504 */ 3505 enum wlan_offloaded_packets_control { 3506 WLAN_START_OFFLOADED_PACKETS = 1, 3507 WLAN_STOP_OFFLOADED_PACKETS = 2 3508 }; 3509 3510 /** 3511 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication 3512 * 3513 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to 3514 * the offloaded data. 3515 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded 3516 * data. 3517 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload 3518 * indication. 3519 */ 3520 enum qca_wlan_vendor_attr_data_offload_ind { 3521 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, 3522 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, 3523 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, 3524 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, 3525 3526 /* keep last */ 3527 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, 3528 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = 3529 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 3530 }; 3531 3532 /** 3533 * enum qca_wlan_vendor_attr_offloaded_packets - offloaded packets 3534 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID: invalid 3535 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL: control 3536 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID: request id 3537 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA: ip packet data 3538 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR: src mac address 3539 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR: destination mac address 3540 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD: period in milli seconds 3541 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST: after last 3542 * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX: max 3543 */ 3544 enum qca_wlan_vendor_attr_offloaded_packets { 3545 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, 3546 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, 3547 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, 3548 3549 /* Packet in hex format */ 3550 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, 3551 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, 3552 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, 3553 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, 3554 3555 /* keep last */ 3556 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, 3557 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = 3558 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, 3559 }; 3560 #endif 3561 3562 /** 3563 * enum qca_wlan_rssi_monitoring_control - rssi control commands 3564 * @QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID: invalid 3565 * @QCA_WLAN_RSSI_MONITORING_START: rssi monitoring start 3566 * @QCA_WLAN_RSSI_MONITORING_STOP: rssi monitoring stop 3567 */ 3568 enum qca_wlan_rssi_monitoring_control { 3569 QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, 3570 QCA_WLAN_RSSI_MONITORING_START, 3571 QCA_WLAN_RSSI_MONITORING_STOP, 3572 }; 3573 3574 /** 3575 * enum qca_wlan_vendor_attr_rssi_monitoring - rssi monitoring 3576 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID: Invalid 3577 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL: control 3578 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI: max rssi 3579 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI: min rssi 3580 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID: current bssid 3581 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI: current rssi 3582 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST: after last 3583 * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX: max 3584 */ 3585 enum qca_wlan_vendor_attr_rssi_monitoring { 3586 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, 3587 3588 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, 3589 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, 3590 3591 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, 3592 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, 3593 3594 /* attributes to be used/received in callback */ 3595 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, 3596 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, 3597 3598 /* keep last */ 3599 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, 3600 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = 3601 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, 3602 }; 3603 3604 /** 3605 * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command 3606 * QCA_NL80211_VENDOR_SUBCMD_NDP. 3607 * @QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID 3608 * @QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD: sub commands values in qca_wlan_ndp_sub_cmd 3609 * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID: 3610 * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID: indicats a service info 3611 * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL: channel frequency in MHz 3612 * @QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR: Interface Discovery MAC 3613 * address 3614 * @QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR: Interface name on which NDP is being 3615 * created 3616 * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY: CONFIG_SECURITY is deprecated, use 3617 * NCS_SK_TYPE/PMK/SCID instead 3618 * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS: value for QoS 3619 * @QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO: app info 3620 * @QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID: NDP instance Id 3621 * @QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY: Array of instance Ids 3622 * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE: initiator/responder NDP response 3623 * code: accept/reject 3624 * @QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR: NDI MAC address 3625 * @QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE: errors types returned by 3626 * driver 3627 * @QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE: value error values returned by 3628 * driver 3629 * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG: Channel setup configuration 3630 * @QCA_WLAN_VENDOR_ATTR_NDP_CSID: Cipher Suite Shared Key Type 3631 * @QCA_WLAN_VENDOR_ATTR_NDP_PMK: PMK_INFO 3632 * @QCA_WLAN_VENDOR_ATTR_NDP_SCID: Security Context Identifier that contains the 3633 * PMKID 3634 * @QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE: passphrase 3635 * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME: service name 3636 * @QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON: bitmap indicating schedule 3637 * update: 3638 * BIT_0: NSS Update 3639 * BIT_1: Channel list update 3640 * @QCA_WLAN_VENDOR_ATTR_NDP_NSS: nss 3641 * @QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS: NUMBER NDP CHANNEL 3642 * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH: CHANNEL BANDWIDTH: 3643 * 0:20 MHz, 3644 * 1:40 MHz, 3645 * 2:80 MHz, 3646 * 3:160 MHz 3647 * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO: Array of channel/band width 3648 * @QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST: id after last valid attribute 3649 * @QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX: max value of this enum type 3650 * @QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR: IPv6 address used by NDP, 16 bytes array 3651 * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT: Unsigned 16-bit value indicating 3652 * transport port used by NDP. 3653 * QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL: Unsigned 8-bit value indicating 3654 * protocol used by NDP and assigned by the Internet Assigned Numbers Authority 3655 * as per: www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml 3656 */ 3657 enum qca_wlan_vendor_attr_ndp_params { 3658 QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, 3659 QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD = 1, 3660 QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID = 2, 3661 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID = 3, 3662 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL = 4, 3663 QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR = 5, 3664 QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR = 6, 3665 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY = 7, 3666 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS = 8, 3667 QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO = 9, 3668 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID = 10, 3669 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY = 11, 3670 QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE = 12, 3671 QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR = 13, 3672 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE = 14, 3673 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE = 15, 3674 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG = 16, 3675 QCA_WLAN_VENDOR_ATTR_NDP_CSID = 17, 3676 QCA_WLAN_VENDOR_ATTR_NDP_PMK = 18, 3677 QCA_WLAN_VENDOR_ATTR_NDP_SCID = 19, 3678 QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE = 20, 3679 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME = 21, 3680 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON = 22, 3681 QCA_WLAN_VENDOR_ATTR_NDP_NSS = 23, 3682 QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS = 24, 3683 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH = 25, 3684 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO = 26, 3685 QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, 3686 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, 3687 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, 3688 3689 /* keep last */ 3690 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, 3691 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = 3692 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, 3693 }; 3694 3695 /** 3696 * enum qca_wlan_ndp_sub_cmd - NDP sub comands types for 3697 * QCA_NL80211_VENDOR_SUBCMD_NDP. 3698 * @QCA_WLAN_VENDOR_ATTR_NDP_INVALID: invalid value 3699 * @QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE: create a ndi 3700 * @QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE: delete a ndi 3701 * @QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST: initiate a ndp session 3702 * @QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE: response for above 3703 * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST: respond to ndp session 3704 * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE: response for above 3705 * @QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST: initiate a ndp end 3706 * @QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE: response for above 3707 * @QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND: notify the peer about the end request 3708 * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND: confirm the ndp session is complete 3709 * @QCA_WLAN_VENDOR_ATTR_NDP_END_IND: indicate the peer about the end request 3710 * being received 3711 * @QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND: indicate the peer of schedule 3712 * update 3713 */ 3714 enum qca_wlan_ndp_sub_cmd { 3715 QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, 3716 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, 3717 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, 3718 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, 3719 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, 3720 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, 3721 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, 3722 QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, 3723 QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, 3724 QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, 3725 QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, 3726 QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, 3727 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 3728 }; 3729 3730 /** 3731 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel 3732 * information. These attributes are sent as part of 3733 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following 3734 * attributes correspond to a single channel. 3735 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS: A bitmask (u16) 3736 * with flags specified in qca_wlan_vendor_channel_prop_flags_ext. 3737 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT: A bitmask (u16) 3738 * with flags specified in qca_wlan_vendor_channel_prop_flags_ext. 3739 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ: frequency 3740 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER: maximum 3741 * regulatory transmission power 3742 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER: maximum 3743 * transmission power 3744 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER: minimum 3745 * transmission power 3746 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID: regulatory 3747 * class id 3748 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN: maximum 3749 * antenna gain in dbm 3750 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0: vht segment 0 3751 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1: vht segment 1 3752 * 3753 */ 3754 enum qca_wlan_vendor_external_acs_event_chan_info_attr { 3755 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, 3756 3757 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, 3758 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, 3759 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, 3760 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, 3761 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, 3762 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, 3763 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, 3764 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, 3765 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, 3766 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, 3767 /* 3768 * A bitmask (u32) with flags specified in 3769 * enum qca_wlan_vendor_channel_prop_flags_2. 3770 */ 3771 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, 3772 3773 /* keep last */ 3774 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, 3775 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = 3776 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, 3777 }; 3778 3779 /** 3780 * enum qca_wlan_vendor_attr_start_acs_config: attribute to vendor sub-command 3781 * QCA_NL80211_VENDOR_SUBCMD_START_ACS. This will be triggered by host 3782 * driver. 3783 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON: This reason refers to 3784 * qca_wlan_vendor_acs_select_reason. This helps acs module to understand why 3785 * ACS need to be started 3786 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED: Does 3787 * driver supports spectral scanning or not 3788 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED: Is 11ac is 3789 * offloaded to firmware. 3790 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT: Does driver 3791 * provides additional channel capability as part of scan operation. 3792 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP:Flag attribute to indicate 3793 * interface status is UP 3794 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE: Operating mode of 3795 * interface. It takes one of nl80211_iftype values. 3796 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH: This is the upper bound 3797 * of chan width. ACS logic should try to get a channel with specified width 3798 * if not found then look for lower values. 3799 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND: nl80211_bands 3800 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE: PHY/HW mode such as 3801 * a/b/g/n/ac. 3802 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST: Supported frequency list 3803 * among which ACS should choose best frequency. 3804 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL:Preferred Chan List by the 3805 * driver which will have <channel(u8), weight(u8)> format as array of 3806 * nested values. 3807 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO: Array of nested attribute 3808 * for each channel. It takes attr as defined in 3809 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY:External ACS policy such as 3810 * PCL mandatory, PCL preferred, etc.It uses values defined in enum 3811 * qca_wlan_vendor_attr_external_acs_policy. 3812 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO: Reference RF 3813 * Operating Parameter (RROP) availability information (u16). It uses values 3814 * defined in enum qca_wlan_vendor_attr_rropavail_info. 3815 */ 3816 enum qca_wlan_vendor_attr_external_acs_event { 3817 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, 3818 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, 3819 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, 3820 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, 3821 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, 3822 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, 3823 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, 3824 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, 3825 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, 3826 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, 3827 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, 3828 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, 3829 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, 3830 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, 3831 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, 3832 3833 /* keep last */ 3834 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, 3835 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = 3836 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, 3837 }; 3838 3839 enum qca_iface_type { 3840 QCA_IFACE_TYPE_STA, 3841 QCA_IFACE_TYPE_AP, 3842 QCA_IFACE_TYPE_P2P_CLIENT, 3843 QCA_IFACE_TYPE_P2P_GO, 3844 QCA_IFACE_TYPE_IBSS, 3845 QCA_IFACE_TYPE_TDLS, 3846 }; 3847 3848 /** 3849 * enum qca_wlan_vendor_attr_pcl_config: attribute to vendor sub-command 3850 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL. 3851 * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_INVALID: invalid value 3852 * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_CHANNEL: pcl channel number 3853 * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_WEIGHT: pcl channel weight 3854 */ 3855 enum qca_wlan_vendor_attr_pcl_config { 3856 QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, 3857 QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, 3858 QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, 3859 }; 3860 3861 enum qca_set_band { 3862 QCA_SETBAND_AUTO, 3863 QCA_SETBAND_5G, 3864 QCA_SETBAND_2G, 3865 }; 3866 3867 /** 3868 * enum set_reset_packet_filter - set packet filter control commands 3869 * @QCA_WLAN_SET_PACKET_FILTER: Set Packet Filter 3870 * @QCA_WLAN_GET_PACKET_FILTER: Get Packet filter 3871 * @QCA_WLAN_WRITE_PACKET_FILTER: Write packet filter program/data 3872 * @QCA_WLAN_READ_PACKET_FILTER: Read packet filter program/data 3873 * @QCA_WLAN_ENABLE_PACKET_FILTER: Enable APF interpreter 3874 * @QCA_WLAN_DISABLE_PACKET_FILTER: Disable APF interpreter 3875 */ 3876 enum set_reset_packet_filter { 3877 QCA_WLAN_SET_PACKET_FILTER = 1, 3878 QCA_WLAN_GET_PACKET_FILTER = 2, 3879 QCA_WLAN_WRITE_PACKET_FILTER = 3, 3880 QCA_WLAN_READ_PACKET_FILTER = 4, 3881 QCA_WLAN_ENABLE_PACKET_FILTER = 5, 3882 QCA_WLAN_DISABLE_PACKET_FILTER = 6, 3883 }; 3884 3885 /** 3886 * enum qca_wlan_vendor_attr_packet_filter - APF control commands 3887 * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID: Invalid 3888 * @QCA_WLAN_VENDOR_ATTR_SET_RESET_PACKET_FILTER: Filter ID 3889 * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION: Filter Version 3890 * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE: Total Length 3891 * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET: Current offset 3892 * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM: length of APF instructions 3893 * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH: length of the program 3894 * section in packet filter buffer 3895 */ 3896 enum qca_wlan_vendor_attr_packet_filter { 3897 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, 3898 QCA_WLAN_VENDOR_ATTR_SET_RESET_PACKET_FILTER, 3899 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, 3900 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, 3901 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, 3902 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, 3903 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, 3904 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH, 3905 3906 /* keep last */ 3907 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, 3908 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = 3909 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, 3910 }; 3911 3912 /** 3913 * enum qca_wlan_vendor_attr_wake_stats - wake lock stats 3914 * @QCA_WLAN_VENDOR_ATTR_GET_WAKE_STATS_INVALID: invalid 3915 * @QCA_WLAN_VENDOR_ATTR_TOTAL_CMD_EVENT_WAKE: 3916 * @QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_PTR: 3917 * @QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_SZ: 3918 * @QCA_WLAN_VENDOR_ATTR_TOTAL_DRIVER_FW_LOCAL_WAKE: 3919 * @QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_PTR: 3920 * @QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_SZ: 3921 * @QCA_WLAN_VENDOR_ATTR_TOTAL_RX_DATA_WAKE: 3922 * total rx wakeup count 3923 * @QCA_WLAN_VENDOR_ATTR_RX_UNICAST_CNT: 3924 * Total rx unicast packet which woke up host 3925 * @QCA_WLAN_VENDOR_ATTR_RX_MULTICAST_CNT: 3926 * Total rx multicast packet which woke up host 3927 * @QCA_WLAN_VENDOR_ATTR_RX_BROADCAST_CNT: 3928 * Total rx broadcast packet which woke up host 3929 * @QCA_WLAN_VENDOR_ATTR_ICMP_PKT: 3930 * wake icmp packet count 3931 * @QCA_WLAN_VENDOR_ATTR_ICMP6_PKT: 3932 * wake icmp6 packet count 3933 * @QCA_WLAN_VENDOR_ATTR_ICMP6_RA: 3934 * wake icmp6 RA packet count 3935 * @QCA_WLAN_VENDOR_ATTR_ICMP6_NA: 3936 * wake icmp6 NA packet count 3937 * @QCA_WLAN_VENDOR_ATTR_ICMP6_NS: 3938 * wake icmp6 NS packet count 3939 * @QCA_WLAN_VENDOR_ATTR_ICMP4_RX_MULTICAST_CNT: 3940 * Rx wake packet count due to ipv4 multicast 3941 * @QCA_WLAN_VENDOR_ATTR_ICMP6_RX_MULTICAST_CNT: 3942 * Rx wake packet count due to ipv6 multicast 3943 * @QCA_WLAN_VENDOR_ATTR_OTHER_RX_MULTICAST_CNT: 3944 * Rx wake packet count due to non-ipv4 and non-ipv6 packets 3945 * @QCA_WLAN_VENDOR_ATTR_RSSI_BREACH_CNT: 3946 * wake rssi breach packet count 3947 * @QCA_WLAN_VENDOR_ATTR_LOW_RSSI_CNT: 3948 * wake low rssi packet count 3949 * @QCA_WLAN_VENDOR_ATTR_GSCAN_CNT: 3950 * wake gscan packet count 3951 * @QCA_WLAN_VENDOR_ATTR_PNO_COMPLETE_CNT: 3952 * wake pno complete packet count 3953 * @QCA_WLAN_VENDOR_ATTR_PNO_MATCH_CNT: 3954 * wake pno match packet count 3955 */ 3956 enum qca_wlan_vendor_attr_wake_stats { 3957 QCA_WLAN_VENDOR_ATTR_GET_WAKE_STATS_INVALID = 0, 3958 QCA_WLAN_VENDOR_ATTR_TOTAL_CMD_EVENT_WAKE, 3959 QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_PTR, 3960 QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_SZ, 3961 QCA_WLAN_VENDOR_ATTR_TOTAL_DRIVER_FW_LOCAL_WAKE, 3962 QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_PTR, 3963 QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_SZ, 3964 QCA_WLAN_VENDOR_ATTR_TOTAL_RX_DATA_WAKE, 3965 QCA_WLAN_VENDOR_ATTR_RX_UNICAST_CNT, 3966 QCA_WLAN_VENDOR_ATTR_RX_MULTICAST_CNT, 3967 QCA_WLAN_VENDOR_ATTR_RX_BROADCAST_CNT, 3968 QCA_WLAN_VENDOR_ATTR_ICMP_PKT, 3969 QCA_WLAN_VENDOR_ATTR_ICMP6_PKT, 3970 QCA_WLAN_VENDOR_ATTR_ICMP6_RA, 3971 QCA_WLAN_VENDOR_ATTR_ICMP6_NA, 3972 QCA_WLAN_VENDOR_ATTR_ICMP6_NS, 3973 QCA_WLAN_VENDOR_ATTR_ICMP4_RX_MULTICAST_CNT, 3974 QCA_WLAN_VENDOR_ATTR_ICMP6_RX_MULTICAST_CNT, 3975 QCA_WLAN_VENDOR_ATTR_OTHER_RX_MULTICAST_CNT, 3976 QCA_WLAN_VENDOR_ATTR_RSSI_BREACH_CNT, 3977 QCA_WLAN_VENDOR_ATTR_LOW_RSSI_CNT, 3978 QCA_WLAN_VENDOR_ATTR_GSCAN_CNT, 3979 QCA_WLAN_VENDOR_ATTR_PNO_COMPLETE_CNT, 3980 QCA_WLAN_VENDOR_ATTR_PNO_MATCH_CNT, 3981 /* keep last */ 3982 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, 3983 QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = 3984 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, 3985 }; 3986 3987 /** 3988 * enum qca_vendor_element_id - QCA Vendor Specific element types 3989 * 3990 * These values are used to identify QCA Vendor Specific elements. The 3991 * payload of the element starts with the three octet OUI (OUI_QCA) and 3992 * is followed by a single octet type which is defined by this enum. 3993 * 3994 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. 3995 * This element can be used to specify preference order for supported 3996 * channels. The channels in this list are in preference order (the first 3997 * one has the highest preference) and are described as a pair of 3998 * (global) Operating Class and Channel Number (each one octet) fields. 3999 * 4000 * This extends the standard P2P functionality by providing option to have 4001 * more than one preferred operating channel. When this element is present, 4002 * it replaces the preference indicated in the Operating Channel attribute. 4003 * For supporting other implementations, the Operating Channel attribute is 4004 * expected to be used with the highest preference channel. Similarly, all 4005 * the channels included in this Preferred channel list element are 4006 * expected to be included in the Channel List attribute. 4007 * 4008 * This vendor element may be included in GO Negotiation Request, P2P 4009 * Invitation Request, and Provision Discovery Request frames. 4010 * 4011 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. 4012 * This element can be used for pre-standard publication testing of HE 4013 * before P802.11ax draft assigns the element ID. The payload of this 4014 * vendor specific element is defined by the latest P802.11ax draft. 4015 * Please note that the draft is still work in progress and this element 4016 * payload is subject to change. 4017 * 4018 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. 4019 * This element can be used for pre-standard publication testing of HE 4020 * before P802.11ax draft assigns the element ID. The payload of this 4021 * vendor specific element is defined by the latest P802.11ax draft. 4022 * Please note that the draft is still work in progress and this element 4023 * payload is subject to change. 4024 * 4025 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set 4026 * element). 4027 * This element can be used for pre-standard publication testing of HE 4028 * before P802.11ax draft assigns the element ID extension. The payload of 4029 * this vendor specific element is defined by the latest P802.11ax draft 4030 * (not including the Element ID Extension field). Please note that the 4031 * draft is still work in progress and this element payload is subject to 4032 * change. 4033 * 4034 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. 4035 * This element can be used for pre-standard publication testing of HE 4036 * before P802.11ax draft assigns the element ID extension. The payload of 4037 * this vendor specific element is defined by the latest P802.11ax draft 4038 * (not including the Element ID Extension field). Please note that the 4039 * draft is still work in progress and this element payload is subject to 4040 * change. 4041 * 4042 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. 4043 * This element can be used for pre-standard publication testing of HE 4044 * before P802.11ax draft assigns the element ID extension. The payload of 4045 * this vendor specific element is defined by the latest P802.11ax draft 4046 * (not including the Element ID Extension field). Please note that the 4047 * draft is still work in progress and this element payload is subject to 4048 * change. 4049 */ 4050 enum qca_vendor_element_id { 4051 QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, 4052 QCA_VENDOR_ELEM_HE_CAPAB = 1, 4053 QCA_VENDOR_ELEM_HE_OPER = 2, 4054 QCA_VENDOR_ELEM_RAPS = 3, 4055 QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, 4056 QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, 4057 }; 4058 4059 /** 4060 * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture 4061 * @QCA_WLAN_VENDOR_ATTR_TSF_INVALID: Invalid attribute value 4062 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32) 4063 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value 4064 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized 4065 * SOC timer value at TSF capture 4066 * @QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST: after last 4067 * @QCA_WLAN_VENDOR_ATTR_TSF_MAX: Max value 4068 */ 4069 enum qca_vendor_attr_tsf_cmd { 4070 QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, 4071 QCA_WLAN_VENDOR_ATTR_TSF_CMD, 4072 QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, 4073 QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, 4074 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, 4075 QCA_WLAN_VENDOR_ATTR_TSF_MAX = 4076 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 4077 }; 4078 4079 /** 4080 * enum qca_tsf_operation: TSF driver commands 4081 * @QCA_TSF_CAPTURE: Initiate TSF Capture 4082 * @QCA_TSF_GET: Get TSF capture value 4083 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value 4084 */ 4085 enum qca_tsf_cmd { 4086 QCA_TSF_CAPTURE, 4087 QCA_TSF_GET, 4088 QCA_TSF_SYNC_GET, 4089 }; 4090 4091 /** 4092 * enum qca_vendor_attr_get_preferred_freq_list - get preferred channel list 4093 * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID: invalid value 4094 * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE: interface type 4095 * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST: preferred frequency list 4096 * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST: after last 4097 * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX: max 4098 */ 4099 enum qca_vendor_attr_get_preferred_freq_list { 4100 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, 4101 /* A 32-unsigned value; the interface type/mode for which the preferred 4102 * frequency list is requested (see enum qca_iface_type for possible 4103 * values); used in both south- and north-bound. 4104 */ 4105 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, 4106 /* An array of 32-unsigned values; values are frequency (MHz); used 4107 * in north-bound only. 4108 */ 4109 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, 4110 /* keep last */ 4111 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, 4112 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = 4113 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 4114 }; 4115 4116 /** 4117 * enum qca_vendor_attr_probable_oper_channel - channel hint 4118 * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID: invalid value 4119 * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE: interface type 4120 * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ: frequency hint value 4121 * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST: last 4122 * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX: max 4123 */ 4124 enum qca_vendor_attr_probable_oper_channel { 4125 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, 4126 /* 32-bit unsigned value; indicates the connection/iface type likely to 4127 * come on this channel (see enum qca_iface_type). 4128 */ 4129 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, 4130 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ 4131 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, 4132 /* keep last */ 4133 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, 4134 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = 4135 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 4136 }; 4137 4138 /** 4139 * enum qca_wlan_vendor_attr_gw_param_config - gateway param config 4140 * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_INVALID: Invalid 4141 * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_GW_MAC_ADDR: gateway mac addr 4142 * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV4_ADDR: ipv4 addr 4143 * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV6_ADDR: ipv6 addr 4144 */ 4145 enum qca_wlan_vendor_attr_gw_param_config { 4146 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_INVALID = 0, 4147 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_GW_MAC_ADDR, 4148 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV4_ADDR, 4149 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV6_ADDR, 4150 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_AFTER_LAST, 4151 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_MAX = 4152 QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_AFTER_LAST - 1, 4153 }; 4154 4155 /** 4156 * enum drv_dbs_capability - DBS capability 4157 * @DRV_DBS_CAPABILITY_DISABLED: DBS disabled 4158 * @DRV_DBS_CAPABILITY_1X1: 1x1 4159 * @DRV_DBS_CAPABILITY_2X2: 2x2 4160 */ 4161 enum drv_dbs_capability { 4162 DRV_DBS_CAPABILITY_DISABLED, /* not supported or disabled */ 4163 DRV_DBS_CAPABILITY_1X1, 4164 DRV_DBS_CAPABILITY_2X2, 4165 }; 4166 4167 /** 4168 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease 4169 * 4170 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. 4171 */ 4172 enum qca_vendor_attr_txpower_decr_db { 4173 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, 4174 /* 4175 * 8-bit unsigned value to indicate the reduction of TX power in dB for 4176 * a virtual interface. 4177 */ 4178 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, 4179 /* keep last */ 4180 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, 4181 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = 4182 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 4183 }; 4184 4185 /** 4186 * enum qca_vendor_attr_ota_test - Enable OTA test 4187 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID: invalid value 4188 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable OTA test 4189 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST: after last 4190 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX: max 4191 */ 4192 enum qca_vendor_attr_ota_test { 4193 QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, 4194 /* 8-bit unsigned value to indicate if OTA test is enabled */ 4195 QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, 4196 /* keep last */ 4197 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, 4198 QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = 4199 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 4200 }; 4201 4202 /** enum qca_vendor_attr_txpower_scale - vendor sub commands index 4203 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID: invalid value 4204 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value 4205 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST: last value 4206 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX: max value 4207 */ 4208 enum qca_vendor_attr_txpower_scale { 4209 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, 4210 /* 8-bit unsigned value to indicate the scaling of tx power */ 4211 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, 4212 /* keep last */ 4213 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, 4214 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = 4215 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 4216 }; 4217 4218 /** 4219 * enum qca_vendor_attr_txpower_scale_decr_db - vendor sub commands index 4220 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_INVALID: invalid value 4221 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB: scaling value 4222 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST: last value 4223 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_MAX: max value 4224 */ 4225 enum qca_vendor_attr_txpower_scale_decr_db { 4226 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_INVALID, 4227 /* 8-bit unsigned value to indicate the scaling of tx power */ 4228 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB, 4229 /* keep last */ 4230 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST, 4231 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_MAX = 4232 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST - 1 4233 }; 4234 4235 /** 4236 * enum dfs_mode - state of DFS mode 4237 * @DFS_MODE_NONE: DFS mode attribute is none 4238 * @DFS_MODE_ENABLE: DFS mode is enabled 4239 * @DFS_MODE_DISABLE: DFS mode is disabled 4240 * @DFS_MODE_DEPRIORITIZE: Deprioritize DFS channels in scanning 4241 */ 4242 enum dfs_mode { 4243 DFS_MODE_NONE, 4244 DFS_MODE_ENABLE, 4245 DFS_MODE_DISABLE, 4246 DFS_MODE_DEPRIORITIZE 4247 }; 4248 4249 /** 4250 * enum qca_wlan_vendor_attr_acs_config - Config params for ACS 4251 * @QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID: Invalid 4252 * @QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE: Dfs mode for ACS 4253 * QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT: channel_hint for ACS 4254 * QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST: after_last 4255 * QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX: max attribute 4256 */ 4257 enum qca_wlan_vendor_attr_acs_config { 4258 QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID = 0, 4259 QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE, 4260 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT, 4261 4262 QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST, 4263 QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX = 4264 QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST - 1, 4265 4266 }; 4267 4268 /** 4269 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability 4270 */ 4271 enum qca_wlan_vendor_attr_get_hw_capability { 4272 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, 4273 /* 4274 * Antenna isolation 4275 * An attribute used in the response. 4276 * The content of this attribute is encoded in a byte array. Each byte 4277 * value is an antenna isolation value. The array length is the number 4278 * of antennas. 4279 */ 4280 QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, 4281 /* 4282 * Request HW capability 4283 * An attribute used in the request. 4284 * The content of this attribute is a u32 array for one or more of 4285 * hardware capabilities (attribute IDs) that are being requested. Each 4286 * u32 value has a value from this 4287 * enum qca_wlan_vendor_attr_get_hw_capability 4288 * identifying which capabilities are requested. 4289 */ 4290 QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, 4291 4292 /* keep last */ 4293 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, 4294 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = 4295 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, 4296 }; 4297 4298 /** 4299 * enum qca_wlan_vendor_attr_sta_connect_roam_policy_config - 4300 * config params for sta roam policy 4301 * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_INVALID: Invalid 4302 * @QCA_WLAN_VENDOR_ATTR_STA_DFS_MODE: If sta should skip Dfs channels 4303 * @QCA_WLAN_VENDOR_ATTR_STA_SKIP_UNSAFE_CHANNEL: 4304 * If sta should skip unsafe channels or not in scanning 4305 * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_LAST: 4306 * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_MAX: max attribute 4307 */ 4308 enum qca_wlan_vendor_attr_sta_connect_roam_policy_config { 4309 QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_INVALID = 0, 4310 QCA_WLAN_VENDOR_ATTR_STA_DFS_MODE, 4311 QCA_WLAN_VENDOR_ATTR_STA_SKIP_UNSAFE_CHANNEL, 4312 4313 QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_AFTER_LAST, 4314 QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_MAX = 4315 QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_AFTER_LAST - 1, 4316 }; 4317 4318 /* Attributes for FTM commands and events */ 4319 4320 /** 4321 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities 4322 * 4323 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See 4324 * enum qca_wlan_vendor_attr_loc_capa_flags. 4325 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number 4326 * of measurement sessions that can run concurrently. 4327 * Default is one session (no session concurrency). 4328 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique 4329 * peers that are supported in running sessions. For example, 4330 * if the value is 8 and maximum number of sessions is 2, you can 4331 * have one session with 8 unique peers, or 2 sessions with 4 unique 4332 * peers each, and so on. 4333 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number 4334 * of bursts per peer, as an exponent (2^value). Default is 0, 4335 * meaning no multi-burst support. 4336 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number 4337 * of measurement exchanges allowed in a single burst. 4338 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement 4339 * types. A bit mask (unsigned 32 bit value), each bit corresponds 4340 * to an AOA type as defined by enum qca_vendor_attr_aoa_type. 4341 */ 4342 enum qca_wlan_vendor_attr_loc_capa { 4343 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, 4344 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, 4345 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, 4346 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, 4347 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, 4348 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, 4349 QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, 4350 /* keep last */ 4351 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, 4352 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = 4353 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, 4354 }; 4355 4356 /** 4357 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags 4358 * 4359 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver 4360 * can be configured as an FTM responder (for example, an AP that 4361 * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 4362 * will be supported if set. 4363 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver 4364 * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION 4365 * will be supported if set. 4366 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder 4367 * supports immediate (ASAP) response. 4368 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone 4369 * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. 4370 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports 4371 * requesting AOA measurements as part of an FTM session. 4372 */ 4373 enum qca_wlan_vendor_attr_loc_capa_flags { 4374 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, 4375 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, 4376 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, 4377 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, 4378 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, 4379 }; 4380 4381 /** 4382 * enum qca_wlan_vendor_attr_sap_config - config params for sap configuration 4383 * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID: invalid 4384 * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL: Channel on which SAP should start 4385 * @QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST: List of frequencies on 4386 * which AP is expected to operate. This is irrespective of ACS configuration. 4387 * This list is a priority based one and is looked for before the AP is created 4388 * to ensure the best concurrency sessions (avoid MCC and use DBS/SCC) co-exist 4389 * in the system. 4390 * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST: after last 4391 * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX: max attribute 4392 */ 4393 enum qca_wlan_vendor_attr_sap_config { 4394 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, 4395 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL, 4396 QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, 4397 /* keep last */ 4398 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, 4399 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = 4400 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, 4401 }; 4402 4403 /** 4404 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about 4405 * a single peer in a measurement session. 4406 * 4407 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. 4408 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related 4409 * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. 4410 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of 4411 * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 4412 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for 4413 * list of supported attributes. 4414 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for 4415 * secure measurement. 4416 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA 4417 * measurement every <value> bursts. If 0 or not specified, 4418 * AOA measurements will be disabled for this peer. 4419 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where 4420 * the measurement frames are exchanged. Optional; if not 4421 * specified, try to locate the peer in the kernel scan 4422 * results cache and use frequency from there. 4423 */ 4424 enum qca_wlan_vendor_attr_ftm_peer_info { 4425 QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, 4426 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, 4427 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, 4428 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, 4429 QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, 4430 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, 4431 QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, 4432 /* keep last */ 4433 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, 4434 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = 4435 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, 4436 }; 4437 4438 /** 4439 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, 4440 * per-peer 4441 * 4442 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request 4443 * immediate (ASAP) response from peer. 4444 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request 4445 * LCI report from peer. The LCI report includes the absolute 4446 * location of the peer in "official" coordinates (similar to GPS). 4447 * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. 4448 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request 4449 * Location civic report from peer. The LCR includes the location 4450 * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, 4451 * 11.24.6.7 for more information. 4452 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, 4453 * request a secure measurement. 4454 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. 4455 */ 4456 enum qca_wlan_vendor_attr_ftm_peer_meas_flags { 4457 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, 4458 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, 4459 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, 4460 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, 4461 }; 4462 4463 /** 4464 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters 4465 * 4466 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements 4467 * to perform in a single burst. 4468 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to 4469 * perform, specified as an exponent (2^value). 4470 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst 4471 * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. 4472 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, 4473 * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must 4474 * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. 4475 */ 4476 enum qca_wlan_vendor_attr_ftm_meas_param { 4477 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, 4478 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, 4479 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, 4480 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, 4481 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, 4482 /* keep last */ 4483 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, 4484 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = 4485 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, 4486 }; 4487 4488 /** 4489 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results 4490 * 4491 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported 4492 * peer. 4493 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement 4494 * request for this peer. 4495 * See enum qca_wlan_vendor_attr_ftm_peer_result_status. 4496 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related 4497 * to measurement results for this peer. 4498 * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. 4499 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when 4500 * request failed and peer requested not to send an additional request 4501 * for this number of seconds. 4502 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received 4503 * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 4504 * 9.4.2.22.10. 4505 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when 4506 * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 4507 * 9.4.2.22.13. 4508 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer 4509 * overridden some measurement request parameters. See 4510 * enum qca_wlan_vendor_attr_ftm_meas_param. 4511 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement 4512 * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 4513 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement 4514 * results. Each entry is a nested attribute defined 4515 * by enum qca_wlan_vendor_attr_ftm_meas. 4516 */ 4517 enum qca_wlan_vendor_attr_ftm_peer_result { 4518 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, 4519 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, 4520 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, 4521 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, 4522 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, 4523 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, 4524 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, 4525 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, 4526 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, 4527 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, 4528 /* keep last */ 4529 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, 4530 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = 4531 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, 4532 }; 4533 4534 /** 4535 * enum qca_wlan_vendor_attr_ftm_peer_result_status 4536 * 4537 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results 4538 * will be provided. Peer may have overridden some measurement parameters, 4539 * in which case overridden parameters will be report by 4540 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. 4541 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable 4542 * of performing the measurement request. No more results will be sent 4543 * for this peer in this session. 4544 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request 4545 * failed, and requested not to send an additional request for number 4546 * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS 4547 * attribute. 4548 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation 4549 * failed. Request was not sent over the air. 4550 */ 4551 enum qca_wlan_vendor_attr_ftm_peer_result_status { 4552 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, 4553 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, 4554 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, 4555 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, 4556 }; 4557 4558 /** 4559 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags 4560 * for measurement result, per-peer 4561 * 4562 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, 4563 * measurement completed for this peer. No more results will be reported 4564 * for this peer in this session. 4565 */ 4566 enum qca_wlan_vendor_attr_ftm_peer_result_flags { 4567 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, 4568 }; 4569 4570 /** 4571 * enum qca_vendor_attr_loc_session_status: Session completion status code 4572 * 4573 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed 4574 * successfully. 4575 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted 4576 * by request. 4577 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request 4578 * was invalid and was not started. 4579 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error 4580 * and did not complete normally (for example out of resources). 4581 */ 4582 enum qca_vendor_attr_loc_session_status { 4583 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, 4584 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, 4585 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, 4586 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, 4587 }; 4588 4589 /** 4590 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data 4591 * 4592 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as 4593 * recorded by responder, in picoseconds. 4594 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 4595 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at 4596 * initiator, in picoseconds. 4597 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 4598 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by 4599 * initiator, in picoseconds. 4600 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 4601 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at 4602 * responder, in picoseconds. 4603 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 4604 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded 4605 * during this measurement exchange. Optional and will be provided if 4606 * the hardware can measure it. 4607 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by 4608 * responder. Not always provided. 4609 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 4610 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by 4611 * responder. Not always provided. 4612 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 4613 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by 4614 * initiator. Not always provided. 4615 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 4616 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by 4617 * initiator. Not always provided. 4618 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 4619 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. 4620 */ 4621 enum qca_wlan_vendor_attr_ftm_meas { 4622 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, 4623 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, 4624 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, 4625 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, 4626 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, 4627 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, 4628 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, 4629 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, 4630 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, 4631 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, 4632 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, 4633 /* keep last */ 4634 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, 4635 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = 4636 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, 4637 }; 4638 4639 /** 4640 * enum qca_wlan_vendor_attr_p2p_listen_offload - vendor sub commands index 4641 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID: invalid value 4642 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL: 4643 * A 32-bit unsigned value; the P2P listen frequency (MHz); must be one 4644 * of the social channels. 4645 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD: listen offload period 4646 * A 32-bit unsigned value; the P2P listen offload period (ms). 4647 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL: 4648 * A 32-bit unsigned value; the P2P listen interval duration (ms). 4649 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT: 4650 * A 32-bit unsigned value; number of interval times the Firmware needs 4651 * to run the offloaded P2P listen operation before it stops. 4652 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES: device types 4653 * An array of unsigned 8-bit characters; vendor information elements. 4654 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE: vendor IEs 4655 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG: control flag for FW 4656 * A 32-bit unsigned value; a control flag to indicate whether listen 4657 * results need to be flushed to wpa_supplicant. 4658 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON: offload stop reason 4659 * A 8-bit unsigned value; reason code for P2P listen offload stop 4660 * event. 4661 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST: last value 4662 * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX: max value 4663 */ 4664 enum qca_wlan_vendor_attr_p2p_listen_offload { 4665 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, 4666 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, 4667 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, 4668 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, 4669 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, 4670 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, 4671 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, 4672 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, 4673 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, 4674 /* keep last */ 4675 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, 4676 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = 4677 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 4678 }; 4679 4680 /** 4681 * enum qca_wlan_vendor_drv_info - WLAN driver info 4682 * @QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID: Invalid 4683 * @QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE: Maximum Message size info 4684 * between Firmware & Host. 4685 */ 4686 enum qca_wlan_vendor_drv_info { 4687 QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, 4688 QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, 4689 4690 /* keep last */ 4691 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, 4692 QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = 4693 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, 4694 }; 4695 4696 /** 4697 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type 4698 * 4699 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest 4700 * CIR (channel impulse response) path for each antenna. 4701 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude 4702 * of the strongest CIR path for each antenna. 4703 */ 4704 enum qca_wlan_vendor_attr_aoa_type { 4705 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, 4706 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, 4707 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX 4708 }; 4709 4710 /** 4711 * enum qca_wlan_vendor_attr_encryption_test - Attributes to 4712 * validate encryption engine 4713 * 4714 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. 4715 * This will be included if the request is for decryption; if not included, 4716 * the request is treated as a request for encryption by default. 4717 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value 4718 * indicating the key cipher suite. Takes same values as 4719 * NL80211_ATTR_KEY_CIPHER. 4720 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value 4721 * Key Id to be used for encryption 4722 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. 4723 * Key (TK) to be used for encryption/decryption 4724 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. 4725 * Packet number to be specified for encryption/decryption 4726 * 6 bytes for TKIP/CCMP/GCMP. 4727 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values 4728 * representing the 802.11 packet (header + payload + FCS) that 4729 * needs to be encrypted/decrypted. 4730 * Encrypted/decrypted response from the driver will also be sent 4731 * to userspace with the same attribute. 4732 */ 4733 enum qca_wlan_vendor_attr_encryption_test { 4734 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, 4735 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, 4736 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, 4737 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, 4738 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, 4739 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, 4740 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, 4741 4742 /* keep last */ 4743 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, 4744 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = 4745 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 4746 }; 4747 4748 /** 4749 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of 4750 * sector for DMG RF sector operations. 4751 * 4752 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector 4753 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector 4754 */ 4755 enum qca_wlan_vendor_attr_dmg_rf_sector_type { 4756 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, 4757 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, 4758 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX 4759 }; 4760 4761 /** 4762 * enum qca_wlan_vendor_attr_fw_state - State of firmware 4763 * 4764 * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state 4765 * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active 4766 */ 4767 enum qca_wlan_vendor_attr_fw_state { 4768 QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR, 4769 QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE, 4770 QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX 4771 }; 4772 4773 /** 4774 * BRP antenna limit mode 4775 * 4776 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force 4777 * antenna limit, BRP will be performed as usual. 4778 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal 4779 * antennas limit. the hardware may use less antennas than the 4780 * maximum limit. 4781 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will 4782 * use exactly the specified number of antennas for BRP. 4783 */ 4784 enum qca_wlan_vendor_attr_brp_ant_limit_mode { 4785 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, 4786 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, 4787 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, 4788 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX 4789 }; 4790 4791 /** 4792 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for 4793 * DMG RF sector configuration for a single RF module. 4794 * The values are defined in a compact way which closely matches 4795 * the way it is stored in HW registers. 4796 * The configuration provides values for 32 antennas and 8 distribution 4797 * amplifiers, and together describes the characteristics of the RF 4798 * sector - such as a beam in some direction with some gain. 4799 * 4800 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index 4801 * of RF module for this configuration. 4802 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge 4803 * amplifier gain index. Unsigned 32 bit number containing 4804 * bits for all 32 antennas. 4805 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge 4806 * amplifier gain index. Unsigned 32 bit number containing 4807 * bits for all 32 antennas. 4808 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge 4809 * amplifier gain index. Unsigned 32 bit number containing 4810 * bits for all 32 antennas. 4811 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values 4812 * for first 16 antennas, 2 bits per antenna. 4813 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values 4814 * for last 16 antennas, 2 bits per antenna. 4815 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains 4816 * DTYPE values (3 bits) for each distribution amplifier, followed 4817 * by X16 switch bits for each distribution amplifier. There are 4818 * total of 8 distribution amplifiers. 4819 */ 4820 enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { 4821 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, 4822 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, 4823 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, 4824 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, 4825 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, 4826 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, 4827 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, 4828 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, 4829 4830 /* keep last */ 4831 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, 4832 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = 4833 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 4834 }; 4835 4836 /** 4837 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for 4838 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS configuration to the host driver. 4839 * 4840 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger 4841 * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode 4842 * represents the different TDLS trigger modes. 4843 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within 4844 * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number 4845 * of packets shall meet the criteria for implicit TDLS setup. 4846 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx 4847 * packets within a duration. 4848 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD to initiate 4849 * a TDLS setup. 4850 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to inititate 4851 * a TDLS Discovery to the Peer. 4852 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of 4853 * discovery attempts to know the TDLS capability of the peer. A peer is 4854 * marked as TDLS not capable if there is no response for all the attempts. 4855 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) 4856 * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD 4857 * number of TX / RX frames meet the criteria for TDLS teardown. 4858 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number 4859 * (u32) of Tx/Rx packets within a duration 4860 * CA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link 4861 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold 4862 * corresponding to the RSSI of the peer below which a TDLS 4863 * setup is triggered. 4864 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold 4865 * corresponding to the RSSI of the peer above which 4866 * a TDLS teardown is triggered. 4867 */ 4868 enum qca_wlan_vendor_attr_tdls_configuration { 4869 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, 4870 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, 4871 4872 /* Attributes configuring the TDLS Implicit Trigger */ 4873 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, 4874 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, 4875 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, 4876 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, 4877 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, 4878 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, 4879 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, 4880 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, 4881 4882 /* keep last */ 4883 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, 4884 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = 4885 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 4886 }; 4887 4888 /** 4889 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in 4890 * the driver. 4891 * 4892 * The following are the different values for 4893 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. 4894 * 4895 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to 4896 * initiate/teardown the TDLS connection to a respective peer comes 4897 * from the user space. wpa_supplicant provides the commands 4898 * TDLS_SETUP, TDLS_TEARDOWN, TDLS_DISCOVER to do this. 4899 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS 4900 * setup/teardown to the eligible peer once the configured criteria 4901 * (such as TX/RX threshold, RSSI) is met. The attributes 4902 * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to 4903 * the different configuration criteria for the TDLS trigger from the 4904 * host driver. 4905 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger 4906 * the TDLS setup / teardown through the implicit mode, only to the 4907 * configured MAC addresses(wpa_supplicant, with tdls_external_control = 1, 4908 * configures the MAC address through TDLS_SETUP/TDLS_TEARDOWN commands). 4909 * External mode works on top of the implicit mode, thus the host Driver 4910 * is expected to be configured in TDLS Implicit mode too to operate in 4911 * External mode. Configuring External mode alone without Implicit 4912 * mode is invalid. 4913 * 4914 * All the above implementations work as expected only when the host driver 4915 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - 4916 * representing that the TDLS message exchange is not internal to the host 4917 * driver, but depends on wpa_supplicant to do the message exchange. 4918 */ 4919 enum qca_wlan_vendor_tdls_trigger_mode { 4920 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, 4921 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, 4922 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, 4923 }; 4924 4925 /** 4926 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits 4927 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 4928 * that is hard-coded in the Board Data File (BDF). 4929 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 4930 * that is hard-coded in the Board Data File (BDF). 4931 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 4932 * that is hard-coded in the Board Data File (BDF). 4933 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 4934 * that is hard-coded in the Board Data File (BDF). 4935 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 4936 * that is hard-coded in the Board Data File (BDF). 4937 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any 4938 * source of SAR power limits, thereby disabling the SAR power 4939 * limit feature. 4940 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power 4941 * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 4942 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power 4943 * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 4944 * 4945 * This enumerates the valid set of values that may be supplied for 4946 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of 4947 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in 4948 * the response to an instance of the 4949 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. 4950 */ 4951 enum qca_vendor_attr_sar_limits_selections { 4952 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, 4953 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, 4954 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, 4955 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, 4956 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, 4957 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, 4958 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, 4959 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, 4960 }; 4961 4962 /** 4963 * enum qca_vendor_attr_sar_limits_spec_modulations - 4964 * SAR limits specification modulation 4965 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - 4966 * CCK modulation 4967 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - 4968 * OFDM modulation 4969 * 4970 * This enumerates the valid set of values that may be supplied for 4971 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an 4972 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an 4973 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor 4974 * command or in the response to an instance of the 4975 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. 4976 */ 4977 enum qca_vendor_attr_sar_limits_spec_modulations { 4978 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, 4979 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, 4980 }; 4981 4982 /** 4983 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits 4984 * 4985 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to 4986 * select which SAR power limit table should be used. Valid 4987 * values are enumerated in enum 4988 * %qca_vendor_attr_sar_limits_selections. The existing SAR 4989 * power limit selection is unchanged if this attribute is not 4990 * present. 4991 * 4992 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value 4993 * which specifies the number of SAR power limit specifications 4994 * which will follow. 4995 * 4996 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power 4997 * limit specifications. The number of specifications is 4998 * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each 4999 * specification contains a set of 5000 * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A 5001 * specification is uniquely identified by the attributes 5002 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, 5003 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and 5004 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always 5005 * contains as a payload the attribute 5006 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT. 5007 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. 5008 * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or 5009 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is 5010 * needed based upon the value of 5011 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. 5012 * 5013 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to 5014 * indicate for which band this specification applies. Valid 5015 * values are enumerated in enum %nl80211_band (although not all 5016 * bands may be supported by a given device). If the attribute is 5017 * not supplied then the specification will be applied to all 5018 * supported bands. 5019 * 5020 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value 5021 * to indicate for which antenna chain this specification 5022 * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the 5023 * attribute is not supplied then the specification will be 5024 * applied to all chains. 5025 * 5026 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) 5027 * value to indicate for which modulation scheme this 5028 * specification applies. Valid values are enumerated in enum 5029 * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute 5030 * is not supplied then the specification will be applied to all 5031 * modulation schemes. 5032 * 5033 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) 5034 * value to specify the actual power limit value in units of 0.5 5035 * dBm (i.e., a value of 11 represents 5.5 dBm). 5036 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is 5037 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. 5038 * 5039 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) 5040 * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. 5041 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is 5042 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. 5043 * 5044 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS 5045 * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. 5046 */ 5047 enum qca_vendor_attr_sar_limits { 5048 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, 5049 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, 5050 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, 5051 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, 5052 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, 5053 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, 5054 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, 5055 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, 5056 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, 5057 5058 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, 5059 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = 5060 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 5061 }; 5062 5063 /** 5064 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring 5065 * offload which is an extension for LL_STATS. 5066 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. 5067 * If MAC counters do not exceed the threshold, FW will report monitored 5068 * link layer counters periodically as this setting. The first report is 5069 * always triggered by this timer. 5070 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). 5071 * For each MAC layer counter, FW holds two copies. One is the current value. 5072 * The other is the last report. Once a current counter's increment is larger 5073 * than the threshold, FW will indicate that counter to host even if the 5074 * monitoring timer does not expire. 5075 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change 5076 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU 5077 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same 5078 * failure code. 5079 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code 5080 * 1: TX packet discarded 5081 * 2: No ACK 5082 * 3: Postpone 5083 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address 5084 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state 5085 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. 5086 * Threshold for all monitored parameters. If per counter dedicated threshold 5087 * is not enabled, this threshold will take effect. 5088 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this 5089 * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. 5090 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID 5091 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID 5092 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters 5093 * Bit0: TX counter unit in MSDU 5094 * Bit1: TX counter unit in MPDU 5095 * Bit2: TX counter unit in PPDU 5096 * Bit3: TX counter unit in byte 5097 * Bit4: Dropped MSDUs 5098 * Bit5: Dropped Bytes 5099 * Bit6: MPDU retry counter 5100 * Bit7: MPDU failure counter 5101 * Bit8: PPDU failure counter 5102 * Bit9: MPDU aggregation counter 5103 * Bit10: MCS counter for ACKed MPDUs 5104 * Bit11: MCS counter for Failed MPDUs 5105 * Bit12: TX Delay counter 5106 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters 5107 * Bit0: MAC RX counter unit in MPDU 5108 * Bit1: MAC RX counter unit in byte 5109 * Bit2: PHY RX counter unit in PPDU 5110 * Bit3: PHY RX counter unit in byte 5111 * Bit4: Disorder counter 5112 * Bit5: Retry counter 5113 * Bit6: Duplication counter 5114 * Bit7: Discard counter 5115 * Bit8: MPDU aggregation size counter 5116 * Bit9: MCS counter 5117 * Bit10: Peer STA power state change (wake to sleep) counter 5118 * Bit11: Peer STA power save counter, total time in PS mode 5119 * Bit12: Probe request counter 5120 * Bit13: Other management frames counter 5121 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA 5122 * Bit0: Idle time 5123 * Bit1: TX time 5124 * Bit2: time RX in current bss 5125 * Bit3: Out of current bss time 5126 * Bit4: Wireless medium busy time 5127 * Bit5: RX in bad condition time 5128 * Bit6: TX in bad condition time 5129 * Bit7: time wlan card not available 5130 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal 5131 * Bit0: Per channel SNR counter 5132 * Bit1: Per channel noise floor counter 5133 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers 5134 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels 5135 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats 5136 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats 5137 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats 5138 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs 5139 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs 5140 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs 5141 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data 5142 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets 5143 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped 5144 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK 5145 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed 5146 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed 5147 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: 5148 * aggregation stats buffer length 5149 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats 5150 * buffer for ACKed MPDUs. 5151 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats 5152 * buffer for failed MPDUs. 5153 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: 5154 * length of delay stats array. 5155 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats 5156 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs 5157 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs 5158 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats 5159 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received 5160 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received 5161 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received 5162 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received 5163 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost 5164 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets 5165 * flagged as retransmissions 5166 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets 5167 * flagged as duplicated 5168 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX 5169 * packets discarded 5170 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation 5171 * stats buffer. 5172 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs 5173 * stats buffer. 5174 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer 5175 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer 5176 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep 5177 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time 5178 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe 5179 * requests received 5180 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt 5181 * frames received 5182 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time 5183 * there is no TX, nor RX, nor interference. 5184 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time 5185 * transmitting packets. 5186 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time 5187 * for receiving. 5188 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time 5189 * interference detected. 5190 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time 5191 * receiving packets with errors. 5192 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time 5193 * TX no-ACK. 5194 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time 5195 * the chip is unable to work in normal conditions. 5196 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time 5197 * receiving packets in current BSS. 5198 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time 5199 * receiving packets not in current BSS. 5200 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas 5201 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: 5202 * This is a container for per antenna signal stats. 5203 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value 5204 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value 5205 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon 5206 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon 5207 */ 5208 enum qca_wlan_vendor_attr_ll_stats_ext { 5209 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, 5210 5211 /* Attributes for configurations */ 5212 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, 5213 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, 5214 5215 /* Peer STA power state change */ 5216 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, 5217 5218 /* TX failure event */ 5219 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, 5220 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, 5221 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, 5222 5223 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, 5224 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, 5225 5226 /* MAC counters */ 5227 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, 5228 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, 5229 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, 5230 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, 5231 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, 5232 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, 5233 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, 5234 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, 5235 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, 5236 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, 5237 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, 5238 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, 5239 5240 /* Sub-attributes for PEER_AC_TX */ 5241 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, 5242 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, 5243 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, 5244 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, 5245 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, 5246 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, 5247 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, 5248 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, 5249 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, 5250 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, 5251 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, 5252 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, 5253 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, 5254 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, 5255 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, 5256 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, 5257 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, 5258 5259 /* Sub-attributes for PEER_AC_RX */ 5260 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, 5261 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, 5262 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, 5263 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, 5264 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, 5265 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, 5266 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, 5267 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, 5268 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, 5269 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, 5270 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, 5271 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, 5272 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, 5273 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, 5274 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, 5275 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, 5276 5277 /* Sub-attributes for CCA_BSS */ 5278 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, 5279 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, 5280 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, 5281 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, 5282 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, 5283 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, 5284 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, 5285 5286 /* sub-attribute for BSS_RX_TIME */ 5287 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, 5288 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, 5289 5290 /* Sub-attributes for PEER_SIGNAL */ 5291 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, 5292 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, 5293 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, 5294 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, 5295 5296 /* Sub-attributes for IFACE_BSS */ 5297 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, 5298 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, 5299 5300 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, 5301 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = 5302 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 5303 }; 5304 5305 /** 5306 * qca_wlan_vendor_attr_external_acs_channels: attribute to vendor subcmd 5307 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carry a list of channels 5308 * in priority order as decided after acs operation in userspace. 5309 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON: One of reason code from 5310 * qca_wlan_vendor_acs_select_reason. 5311 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_COUNT: Number of channels in 5312 * this list 5313 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST: Array of nested values 5314 * for each channel with following attributes: 5315 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, 5316 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, 5317 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, 5318 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, 5319 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH 5320 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY: Primary channel (u8) 5321 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY: Secondary channel (u8) 5322 * required only for 160 / 80 + 80 5323 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0: VHT seg0 channel (u8) 5324 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1: VHT seg1 channel (u8) 5325 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH:channel width (u8) 5326 */ 5327 enum qca_wlan_vendor_attr_external_acs_channels { 5328 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, 5329 5330 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, 5331 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, 5332 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, 5333 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, 5334 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, 5335 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, 5336 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, 5337 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, 5338 5339 /* keep last */ 5340 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, 5341 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = 5342 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 5343 }; 5344 5345 /** 5346 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why 5347 * the ACS has to be triggered. These parameters are used by 5348 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and 5349 * QCA_NL80211_VENDOR_SUBCMD_ACS_SET_CHANNELS 5350 * @QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT: Represents the reason that the 5351 * ACS triggered during the AP start 5352 * @QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS: Represents the reason that 5353 * DFS found with current channel 5354 * @QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX: Represents the reason that 5355 * LTE CO-Exist in current band 5356 */ 5357 enum qca_wlan_vendor_acs_select_reason { 5358 QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, 5359 QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, 5360 QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, 5361 }; 5362 5363 /** 5364 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration 5365 */ 5366 enum qca_wlan_gpio_attr { 5367 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, 5368 /* Unsigned 32-bit attribute for GPIO command */ 5369 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND, 5370 /* Unsigned 32-bit attribute for GPIO PIN number to configure */ 5371 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM, 5372 /* Unsigned 32-bit attribute for GPIO value to configure */ 5373 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE, 5374 /* Unsigned 32-bit attribute for GPIO pull type */ 5375 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE, 5376 /* Unsigned 32-bit attribute for GPIO interrupt mode */ 5377 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE, 5378 5379 /* keep last */ 5380 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, 5381 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = 5382 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1, 5383 }; 5384 5385 /** 5386 * qca_wlan_set_qdepth_thresh_attr - Parameters for setting 5387 * MSDUQ depth threshold per peer per tid in the target 5388 * 5389 * Associated Vendor Command: 5390 * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH 5391 */ 5392 enum qca_wlan_set_qdepth_thresh_attr { 5393 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, 5394 /* 6-byte MAC address */ 5395 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, 5396 /* Unsigned 32-bit attribute for holding the TID */ 5397 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, 5398 /* Unsigned 32-bit attribute for holding the update mask 5399 * bit 0 - Update high priority msdu qdepth threshold 5400 * bit 1 - Update low priority msdu qdepth threshold 5401 * bit 2 - Update UDP msdu qdepth threshold 5402 * bit 3 - Update Non UDP msdu qdepth threshold 5403 * rest of bits are reserved 5404 */ 5405 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, 5406 /* Unsigned 32-bit attribute for holding the threshold value */ 5407 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, 5408 5409 /* keep last */ 5410 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, 5411 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = 5412 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, 5413 }; 5414 5415 /** 5416 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for 5417 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd 5418 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the 5419 * external ACS policies to select the channels w.r.t. the PCL weights. 5420 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and 5421 * their PCL weights.) 5422 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to 5423 * select a channel with non-zero PCL weight. 5424 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a 5425 * channel with non-zero PCL weight. 5426 * 5427 */ 5428 enum qca_wlan_vendor_attr_external_acs_policy { 5429 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, 5430 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, 5431 }; 5432 5433 /** 5434 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters 5435 */ 5436 enum qca_wlan_vendor_attr_spectral_scan { 5437 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, 5438 /* 5439 * Number of times the chip enters spectral scan mode before 5440 * deactivating spectral scans. When set to 0, chip will enter spectral 5441 * scan mode continuously. u32 attribute. 5442 */ 5443 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, 5444 /* 5445 * Spectral scan period. Period increment resolution is 256*Tclk, 5446 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. 5447 */ 5448 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, 5449 /* Spectral scan priority. u32 attribute. */ 5450 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, 5451 /* Number of FFT data points to compute. u32 attribute. */ 5452 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, 5453 /* 5454 * Enable targeted gain change before starting the spectral scan FFT. 5455 * u32 attribute. 5456 */ 5457 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, 5458 /* Restart a queued spectral scan. u32 attribute. */ 5459 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, 5460 /* 5461 * Noise floor reference number for the calculation of bin power. 5462 * u32 attribute. 5463 */ 5464 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, 5465 /* 5466 * Disallow spectral scan triggers after TX/RX packets by setting 5467 * this delay value to roughly SIFS time period or greater. 5468 * u32 attribute. 5469 */ 5470 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, 5471 /* 5472 * Number of strong bins (inclusive) per sub-channel, below 5473 * which a signal is declared a narrow band tone. u32 attribute. 5474 */ 5475 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, 5476 /* 5477 * Specify the threshold over which a bin is declared strong (for 5478 * scan bandwidth analysis). u32 attribute. 5479 */ 5480 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, 5481 /* Spectral scan report mode. u32 attribute. */ 5482 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, 5483 /* 5484 * RSSI report mode, if the ADC RSSI is below 5485 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, 5486 * then FFTs will not trigger, but timestamps and summaries get 5487 * reported. u32 attribute. 5488 */ 5489 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, 5490 /* 5491 * ADC RSSI must be greater than or equal to this threshold (signed dB) 5492 * to ensure spectral scan reporting with normal error code. 5493 * u32 attribute. 5494 */ 5495 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, 5496 /* 5497 * Format of frequency bin magnitude for spectral scan triggered FFTs: 5498 * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). 5499 * u32 attribute. 5500 */ 5501 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, 5502 /* 5503 * Format of FFT report to software for spectral scan triggered FFTs. 5504 * 0: No FFT report (only spectral scan summary report) 5505 * 1: 2-dword summary of metrics for each completed FFT + spectral scan 5506 * report 5507 * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled 5508 * bins (in-band) per FFT + spectral scan summary report 5509 * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled 5510 * bins (all) per FFT + spectral scan summary report 5511 * u32 attribute. 5512 */ 5513 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, 5514 /* 5515 * Number of LSBs to shift out in order to scale the FFT bins. 5516 * u32 attribute. 5517 */ 5518 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, 5519 /* 5520 * Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes 5521 * in dBm power. u32 attribute. 5522 */ 5523 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, 5524 /* 5525 * Per chain enable mask to select input ADC for search FFT. 5526 * u32 attribute. 5527 */ 5528 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, 5529 /* 5530 * An unsigned 64-bit integer provided by host driver to identify the 5531 * spectral scan request. This attribute is included in the scan 5532 * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START 5533 * and used as an attribute in 5534 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the 5535 * specific scan to be stopped. 5536 */ 5537 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, 5538 /* Skip interval for FFT reports. u32 attribute */ 5539 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, 5540 /* Set to report only one set of FFT results. 5541 * u32 attribute. 5542 */ 5543 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, 5544 /* Debug level for spectral module in driver. 5545 * 0 : Verbosity level 0 5546 * 1 : Verbosity level 1 5547 * 2 : Verbosity level 2 5548 * 3 : Matched filterID display 5549 * 4 : One time dump of FFT report 5550 * u32 attribute. 5551 */ 5552 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, 5553 /* Type of spectral scan request. u32 attribute. 5554 * It uses values defined in enum 5555 * qca_wlan_vendor_attr_spectral_scan_request_type. 5556 */ 5557 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, 5558 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, 5559 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = 5560 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, 5561 }; 5562 5563 /** 5564 * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command 5565 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. 5566 */ 5567 enum qca_wlan_vendor_attr_spectral_diag_stats { 5568 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, 5569 /* Number of spectral TLV signature mismatches. 5570 * u64 attribute. 5571 */ 5572 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, 5573 /* Number of spectral phyerror events with insufficient length when 5574 * parsing for secondary 80 search FFT report. u64 attribute. 5575 */ 5576 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, 5577 /* Number of spectral phyerror events without secondary 80 5578 * search FFT report. u64 attribute. 5579 */ 5580 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, 5581 /* Number of spectral phyerror events with vht operation segment 1 id 5582 * mismatches in search fft report. u64 attribute. 5583 */ 5584 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, 5585 /* Number of spectral phyerror events with vht operation segment 2 id 5586 * mismatches in search fft report. u64 attribute. 5587 */ 5588 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, 5589 5590 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, 5591 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = 5592 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, 5593 }; 5594 5595 /** 5596 * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command 5597 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. 5598 */ 5599 enum qca_wlan_vendor_attr_spectral_cap { 5600 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, 5601 /* Flag attribute to indicate phydiag capability */ 5602 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, 5603 /* Flag attribute to indicate radar detection capability */ 5604 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, 5605 /* Flag attribute to indicate spectral capability */ 5606 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, 5607 /* Flag attribute to indicate advanced spectral capability */ 5608 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, 5609 /* Spectral hardware generation. u32 attribute. 5610 * It uses values defined in enum 5611 * qca_wlan_vendor_spectral_scan_cap_hw_gen. 5612 */ 5613 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, 5614 /* Spectral bin scaling formula ID. u16 attribute. 5615 * It uses values defined in enum 5616 * qca_wlan_vendor_spectral_scan_cap_formula_id. 5617 */ 5618 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6, 5619 /* Spectral bin scaling param - low level offset. 5620 * s16 attribute. 5621 */ 5622 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7, 5623 /* Spectral bin scaling param - high level offset. 5624 * s16 attribute. 5625 */ 5626 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8, 5627 /* Spectral bin scaling param - RSSI threshold. 5628 * s16 attribute. 5629 */ 5630 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9, 5631 /* Spectral bin scaling param - default AGC max gain. 5632 * u8 attribute. 5633 */ 5634 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10, 5635 5636 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, 5637 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = 5638 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, 5639 }; 5640 5641 /** 5642 * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command 5643 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. 5644 */ 5645 enum qca_wlan_vendor_attr_spectral_scan_status { 5646 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, 5647 /* Flag attribute to indicate whether spectral scan is enabled */ 5648 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, 5649 /* Flag attribute to indicate whether spectral scan is in progress*/ 5650 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, 5651 5652 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, 5653 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = 5654 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, 5655 }; 5656 5657 /** 5658 * enum qca_wlan_vendor_attr_config_latency_level - Level for 5659 * wlan latency module. 5660 * 5661 * There will be various of Wi-Fi functionality like scan/roaming/adaptive 5662 * power saving which would causing data exchange out of service, this 5663 * would be a big impact on latency. For latency sensitive applications over 5664 * Wi-Fi are intolerant to such operations and thus would configure them 5665 * to meet their respective needs. It is well understood by such applications 5666 * that altering the default behavior would degrade the Wi-Fi functionality 5667 * w.r.t the above pointed WLAN operations. 5668 * 5669 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: 5670 * Default WLAN operation level which throughput orientated. 5671 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE: 5672 * Use moderate level to improve latency by limit scan duration. 5673 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: 5674 * Use low latency level to benifit application like concurrent 5675 * downloading or video streaming via constraint scan/adaptive PS. 5676 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: 5677 * Use ultra low latency level to benefit for gaming/voice 5678 * application via constraint scan/roaming/adaptive PS. 5679 */ 5680 enum qca_wlan_vendor_attr_config_latency_level { 5681 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, 5682 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, 5683 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2, 5684 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, 5685 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, 5686 5687 /* keep last */ 5688 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, 5689 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = 5690 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, 5691 }; 5692 5693 /** 5694 * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for 5695 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd 5696 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the 5697 * spectral scan request types. 5698 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to 5699 * set the spectral parameters and start scan. 5700 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to 5701 * only set the spectral parameters. 5702 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to 5703 * only start the spectral scan. 5704 */ 5705 enum qca_wlan_vendor_attr_spectral_scan_request_type { 5706 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, 5707 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, 5708 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, 5709 }; 5710 5711 /** 5712 * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for 5713 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd 5714 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the 5715 * spectral hardware generation. 5716 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 5717 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 5718 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 5719 */ 5720 enum qca_wlan_vendor_spectral_scan_cap_hw_gen { 5721 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, 5722 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, 5723 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, 5724 }; 5725 5726 /** 5727 * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for 5728 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd 5729 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the 5730 * Spectral bin scaling formula ID. 5731 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling 5732 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain 5733 * and RSSI threshold based formula. 5734 */ 5735 enum qca_wlan_vendor_spectral_scan_cap_formula_id { 5736 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0, 5737 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1, 5738 }; 5739 5740 /** 5741 * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative 5742 * RF Operating Parameter (RROP) information is available, and if so, at which 5743 * point in the application-driver interaction sequence it can be retrieved by 5744 * the application from the driver. This point may vary by architecture and 5745 * other factors. This is a u16 value. 5746 */ 5747 enum qca_wlan_vendor_attr_rropavail_info { 5748 /* RROP information is unavailable. */ 5749 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, 5750 /* RROP information is available and the application can retrieve the 5751 * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS 5752 * event from the driver. 5753 */ 5754 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, 5755 /* RROP information is available only after a vendor specific scan 5756 * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has 5757 * successfully completed. The application can retrieve the information 5758 * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from 5759 * the driver. 5760 */ 5761 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, 5762 }; 5763 5764 /** 5765 * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific 5766 * Representative RF Operating Parameter (RROP) information. It is sent for the 5767 * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is 5768 * intended for use by external Auto Channel Selection applications. It provides 5769 * guidance values for some RF parameters that are used by the system during 5770 * operation. These values could vary by channel, band, radio, and so on. 5771 */ 5772 enum qca_wlan_vendor_attr_rrop_info { 5773 QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, 5774 5775 /* Representative Tx Power List (RTPL) which has an array of nested 5776 * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. 5777 */ 5778 QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, 5779 5780 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, 5781 QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = 5782 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 5783 }; 5784 5785 /** 5786 * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list 5787 * entry instances in the Representative Tx Power List (RTPL). It provides 5788 * simplified power values intended for helping external Auto channel Selection 5789 * applications compare potential Tx power performance between channels, other 5790 * operating conditions remaining identical. These values are not necessarily 5791 * the actual Tx power values that will be used by the system. They are also not 5792 * necessarily the max or average values that will be used. Instead, they are 5793 * relative, summarized keys for algorithmic use computed by the driver or 5794 * underlying firmware considering a number of vendor specific factors. 5795 */ 5796 enum qca_wlan_vendor_attr_rtplinst { 5797 QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, 5798 5799 /* Primary channel number (u8) */ 5800 QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, 5801 /* Representative Tx power in dBm (s32) with emphasis on throughput. */ 5802 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, 5803 /* Representative Tx power in dBm (s32) with emphasis on range. */ 5804 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, 5805 5806 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, 5807 QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = 5808 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, 5809 }; 5810 5811 /** 5812 * enum qca_wlan_vendor_attr_mac - Used by the vendor command 5813 * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. 5814 * 5815 * @QCA_WLAN_VENDOR_ATTR_MAC_INFO: MAC mode info list which has an 5816 * array of nested values as per attributes in 5817 * enum qca_wlan_vendor_attr_mac_mode_info. 5818 */ 5819 enum qca_wlan_vendor_attr_mac { 5820 QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, 5821 QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, 5822 5823 /* keep last */ 5824 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, 5825 QCA_WLAN_VENDOR_ATTR_MAC_MAX = 5826 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, 5827 }; 5828 5829 /** 5830 * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected 5831 * WiFi netdev interface on a respective MAC. Used by the attribute 5832 * QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. 5833 * 5834 * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_ID: Wi-Fi Netdev's interface id(u32). 5835 * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ: Associated frequency in MHz of 5836 * the connected Wi-Fi interface(u32). 5837 */ 5838 enum qca_wlan_vendor_attr_mac_iface_info { 5839 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, 5840 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, 5841 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, 5842 5843 /* keep last */ 5844 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, 5845 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = 5846 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, 5847 }; 5848 5849 /** 5850 * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. 5851 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the 5852 * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. 5853 * 5854 * @QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID: Hardware MAC ID associated for the 5855 * MAC (u32) 5856 * @QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND: Band supported by the respective MAC 5857 * at a given point. This is a u32 bitmask of BIT(NL80211_BAND_*) as described 5858 * in enum nl80211_band. 5859 * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO: Refers to list of WLAN net dev 5860 * interfaces associated with this MAC. Represented by enum 5861 * qca_wlan_vendor_attr_mac_iface_info. 5862 */ 5863 enum qca_wlan_vendor_attr_mac_info { 5864 QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, 5865 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, 5866 QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, 5867 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, 5868 5869 /* keep last */ 5870 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, 5871 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = 5872 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, 5873 5874 }; 5875 5876 #if !(defined (SUPPORT_WDEV_CFG80211_VENDOR_EVENT_ALLOC)) && \ 5877 (LINUX_VERSION_CODE < KERNEL_VERSION(4, 1, 0)) && \ 5878 !(defined(WITH_BACKPORTS)) 5879 5880 static inline struct sk_buff * 5881 backported_cfg80211_vendor_event_alloc(struct wiphy *wiphy, 5882 struct wireless_dev *wdev, 5883 int approxlen, 5884 int event_idx, gfp_t gfp) 5885 { 5886 struct sk_buff *skb; 5887 5888 skb = cfg80211_vendor_event_alloc(wiphy, approxlen, event_idx, gfp); 5889 5890 if (skb && wdev) { 5891 struct nlattr *attr; 5892 u32 ifindex = wdev->netdev->ifindex; 5893 5894 nla_nest_cancel(skb, ((void **)skb->cb)[2]); 5895 if (nla_put_u32(skb, NL80211_ATTR_IFINDEX, ifindex)) 5896 goto nla_fail; 5897 5898 attr = nla_nest_start(skb, NL80211_ATTR_VENDOR_DATA); 5899 ((void **)skb->cb)[2] = attr; 5900 } 5901 5902 return skb; 5903 5904 nla_fail: 5905 kfree_skb(skb); 5906 5907 return NULL; 5908 } 5909 #define cfg80211_vendor_event_alloc backported_cfg80211_vendor_event_alloc 5910 #endif 5911 5912 /** 5913 * enum he_fragmentation_val - HE fragmentation support values 5914 * Indicates level of dynamic fragmentation that is supported by 5915 * a STA as a recipient. 5916 * HE fragmentation values are defined as per 11ax spec and are used in 5917 * HE capability IE to advertise the support. These values are validated 5918 * in the driver to check the device capability and advertised in the HE 5919 * capability element. 5920 * 5921 * @HE_FRAG_DISABLE: no support for dynamic fragmentation 5922 * @HE_FRAG_LEVEL1: support for dynamic fragments that are 5923 * contained within an MPDU or S-MPDU, no support for dynamic fragments 5924 * within an A-MPDU that is not an S-MPDU. 5925 * @HE_FRAG_LEVEL2: support for dynamic fragments that are 5926 * contained within an MPDU or S-MPDU and support for up to one dynamic 5927 * fragment for each MSDU, each A-MSDU if supported by the recipient, and 5928 * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an 5929 * MPDU or S-MPDU. 5930 * @HE_FRAG_LEVEL3: support for dynamic fragments that are 5931 * contained within an MPDU or S-MPDU and support for multiple dynamic 5932 * fragments for each MSDU and for each A-MSDU if supported by the 5933 * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic 5934 * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. 5935 */ 5936 enum he_fragmentation_val { 5937 HE_FRAG_DISABLE, 5938 HE_FRAG_LEVEL1, 5939 HE_FRAG_LEVEL2, 5940 HE_FRAG_LEVEL3, 5941 }; 5942 5943 /** 5944 * enum he_mcs_config - HE MCS support configuration 5945 * 5946 * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. 5947 * These values are used in driver to configure the HE MCS map to advertise 5948 * Tx/Rx MCS map in HE capability and these values are applied for all the 5949 * streams supported by the device. To configure MCS for different bandwidths, 5950 * vendor command needs to be sent using this attribute with appropriate value. 5951 * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS 5952 * attribute with QCA_WLAN_VENDOR_ATTR_HE_80_MCS0_7. And to configure HE MCS 5953 * for HE_160_MCS0_11 send this command using HE MCS config attribute with 5954 * value QCA_WLAN_VENDOR_ATTR_HE_160_MCS0_11; 5955 * 5956 * @HE_80_MCS0_7: support for HE 80/40/20MHz MCS 0 to 7 5957 * @HE_80_MCS0_9: support for HE 80/40/20MHz MCS 0 to 9 5958 * @HE_80_MCS0_11: support for HE 80/40/20MHz MCS 0 to 11 5959 * @HE_160_MCS0_7: support for HE 160MHz MCS 0 to 7 5960 * @HE_160_MCS0_9: support for HE 160MHz MCS 0 to 9 5961 * @HE_160_MCS0_11: support for HE 160MHz MCS 0 to 11 5962 * @HE_80p80_MCS0_7: support for HE 80p80MHz MCS 0 to 7 5963 * @HE_80p80_MCS0_9: support for HE 80p80MHz MCS 0 to 9 5964 * @HE_80p80_MCS0_11: support for HE 80p80MHz MCS 0 to 11 5965 */ 5966 enum he_mcs_config { 5967 HE_80_MCS0_7 = 0, 5968 HE_80_MCS0_9 = 1, 5969 HE_80_MCS0_11 = 2, 5970 HE_160_MCS0_7 = 4, 5971 HE_160_MCS0_9 = 5, 5972 HE_160_MCS0_11 = 6, 5973 HE_80p80_MCS0_7 = 8, 5974 HE_80p80_MCS0_9 = 9, 5975 HE_80p80_MCS0_11 = 10, 5976 }; 5977 5978 /** 5979 * enum qca_wlan_ba_session_config - BA session configuration 5980 * 5981 * Indicates the configuration values for BA session configuration attribute. 5982 * 5983 * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. 5984 * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. 5985 */ 5986 enum qca_wlan_ba_session_config { 5987 QCA_WLAN_ADD_BA = 1, 5988 QCA_WLAN_DELETE_BA = 2, 5989 }; 5990 5991 /** 5992 * enum qca_wlan_ac_type - access category type 5993 * 5994 * Indicates the access category type value. 5995 * 5996 * @QCA_WLAN_AC_BE: BE access category 5997 * @QCA_WLAN_AC_BK: BK access category 5998 * @QCA_WLAN_AC_VI: VI access category 5999 * @QCA_WLAN_AC_VO: VO access category 6000 * @QCA_WLAN_AC_ALL: All ACs 6001 */ 6002 enum qca_wlan_ac_type { 6003 QCA_WLAN_AC_BE = 0, 6004 QCA_WLAN_AC_BK = 1, 6005 QCA_WLAN_AC_VI = 2, 6006 QCA_WLAN_AC_VO = 3, 6007 QCA_WLAN_AC_ALL = 4, 6008 }; 6009 6010 /** 6011 * enum qca_wlan_he_ltf_cfg - HE LTF configuration 6012 * 6013 * Indicates the HE LTF configuration value. 6014 * 6015 * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to 6016 * the mandatory HE-LTF based on the GI setting 6017 * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF 6018 * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF 6019 * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF 6020 */ 6021 enum qca_wlan_he_ltf_cfg { 6022 QCA_WLAN_HE_LTF_AUTO = 0, 6023 QCA_WLAN_HE_LTF_1X = 1, 6024 QCA_WLAN_HE_LTF_2X = 2, 6025 QCA_WLAN_HE_LTF_4X = 3, 6026 }; 6027 6028 /** 6029 * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration 6030 * 6031 * Indicates the HE trigger frame MAC padding duration value. 6032 * 6033 * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to 6034 * process the trigger frame. 6035 * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for 6036 * trigger frame. 6037 * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for 6038 * trigger frame. 6039 */ 6040 enum qca_wlan_he_mac_padding_dur { 6041 QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, 6042 QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, 6043 QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, 6044 }; 6045 6046 /** 6047 * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration 6048 * 6049 * Indicates the HE Operating mode control channel width setting value. 6050 * 6051 * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz 6052 * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz 6053 * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz 6054 * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz 6055 */ 6056 enum qca_wlan_he_om_ctrl_ch_bw { 6057 QCA_WLAN_HE_OM_CTRL_BW_20M = 0, 6058 QCA_WLAN_HE_OM_CTRL_BW_40M = 1, 6059 QCA_WLAN_HE_OM_CTRL_BW_80M = 2, 6060 QCA_WLAN_HE_OM_CTRL_BW_160M = 3, 6061 }; 6062 6063 /** 6064 * enum qca_wlan_vendor_attr_he_omi_tx: Represents attributes for 6065 * HE operating mode control transmit request. These attributes are 6066 * sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX and 6067 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 6068 * 6069 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value 6070 * indicates the maximum number of spatial streams, NSS, that the STA 6071 * supports in reception for PPDU bandwidths less than or equal to 80 MHz 6072 * and is set to NSS - 1. 6073 * 6074 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value 6075 * indicates the operating channel width supported by the STA for both 6076 * reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values. 6077 * 6078 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value 6079 * indicates the all trigger based UL MU operations by the STA. 6080 * 0 - UL MU operations are enabled by the STA. 6081 * 1 - All triggered UL MU transmissions are suspended by the STA. 6082 * 6083 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value 6084 * indicates the maximum number of space-time streams, NSTS, that 6085 * the STA supports in transmission and is set to NSTS - 1. 6086 */ 6087 enum qca_wlan_vendor_attr_he_omi_tx { 6088 QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0, 6089 QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1, 6090 QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2, 6091 QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3, 6092 QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4, 6093 6094 /* keep last */ 6095 QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST, 6096 QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX = 6097 QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST - 1, 6098 }; 6099 6100 /* Attributes for data used by 6101 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION 6102 */ 6103 enum qca_wlan_vendor_attr_wifi_test_config { 6104 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, 6105 /* 8-bit unsigned value to configure the driver to enable/disable 6106 * WMM feature. This attribute is used to configure testbed device. 6107 * 1-enable, 0-disable 6108 */ 6109 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, 6110 6111 /* 8-bit unsigned value to configure the driver to accept/reject 6112 * the addba request from peer. This attribute is used to configure 6113 * the testbed device. 6114 * 1-accept addba, 0-reject addba 6115 */ 6116 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, 6117 6118 /* 8-bit unsigned value to configure the driver to send or not to 6119 * send the addba request to peer. 6120 * This attribute is used to configure the testbed device. 6121 * 1-send addba, 0-do not send addba 6122 */ 6123 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, 6124 6125 /* 8-bit unsigned value to indicate the HE fragmentation support. 6126 * Uses enum he_fragmentation_val values. 6127 * This attribute is used to configure the testbed device to 6128 * allow the advertised hardware capabilities to be downgraded 6129 * for testing purposes. 6130 */ 6131 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, 6132 6133 /* 8-bit unsigned value to indicate the HE MCS support. 6134 * Uses enum he_mcs_config values. 6135 * This attribute is used to configure the testbed device to 6136 * allow the advertised hardware capabilities to be downgraded 6137 * for testing purposes. 6138 */ 6139 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, 6140 6141 /* 8-bit unsigned value to configure the driver to allow or not to 6142 * allow the connection with WEP/TKIP in HT/VHT/HE modes. 6143 * This attribute is used to configure the testbed device. 6144 * 1-allow wep/tkip in HT/VHT/HE, 0-do not allow wep/tkip 6145 */ 6146 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, 6147 6148 /* 8-bit unsigned value to configure the driver to add a 6149 * new BA session or delete the existing BA session for 6150 * given TID. ADDBA command uses the buffer size and tid 6151 * configuration if user specifies the values else default 6152 * value for buffer size is used for all tids if the tid 6153 * also not specified. For DEL_BA command TID value is 6154 * required to process the command. 6155 * Uses enum qca_wlan_ba_session_config values. 6156 * This attribute is used to configure the testbed device. 6157 */ 6158 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, 6159 6160 /* 16-bit unsigned value to configure the buffer size in addba 6161 * request and response frames. 6162 * This attribute is used to configure the testbed device. 6163 * The range of the value is 0 to 256. 6164 */ 6165 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, 6166 6167 /* 8-bit unsigned value to configure the buffer size in addba 6168 * request and response frames. 6169 * This attribute is used to configure the testbed device. 6170 */ 6171 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, 6172 6173 /* 8-bit unsigned value to configure the no ack policy. 6174 * To configure no ack policy, access category value 6175 * is required to process the command. 6176 * This attribute is used to configure the testbed device. 6177 * 1 - enable no ack, 0 - disable no ack 6178 */ 6179 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, 6180 6181 /* 8-bit unsigned value to configure the AC for no ack policy 6182 * This attribute is used to configure the testbed device. 6183 * uses the enum qca_wlan_ac_type values 6184 */ 6185 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, 6186 6187 /* 8-bit unsigned value to configure the HE LTF 6188 * This attribute is used to configure the testbed device. 6189 * Uses the enum qca_wlan_he_ltf_cfg values. 6190 */ 6191 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, 6192 6193 /* 8-bit unsigned value to configure the tx beamformee. 6194 * This attribute is used to configure the testbed device. 6195 * 1 - enable, 0 - disable. 6196 */ 6197 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, 6198 6199 /* 8-bit unsigned value to configure the tx beamformee number of 6200 * space-time streams. 6201 * This attribute is used to configure the testbed device. 6202 * The range of the value is 0 to 8 6203 */ 6204 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, 6205 6206 /* 8-bit unsigned value to configure the MU EDCA params for given AC 6207 * This attribute is used to configure the testbed device. 6208 * Uses the enum qca_wlan_ac_type values. 6209 */ 6210 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, 6211 6212 /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC 6213 * To configure MU EDCA AIFSN value, MU EDCA access category value 6214 * is required to process the command. 6215 * This attribute is used to configure the testbed device. 6216 */ 6217 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, 6218 6219 /* 8-bit unsigned value to configure the MU EDCA ECW min value for 6220 * given AC. 6221 * To configure MU EDCA ECW min value, MU EDCA access category value 6222 * is required to process the command. 6223 * This attribute is used to configure the testbed device. 6224 */ 6225 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, 6226 6227 /* 8-bit unsigned value to configure the MU EDCA ECW max value for 6228 * given AC. 6229 * To configure MU EDCA ECW max value, MU EDCA access category value 6230 * is required to process the command. 6231 * This attribute is used to configure the testbed device. 6232 */ 6233 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, 6234 6235 /* 8-bit unsigned value to configure the MU EDCA timer for given AC 6236 * To configure MU EDCA timer value, MU EDCA access category value 6237 * is required to process the command. 6238 * This attribute is used to configure the testbed device. 6239 */ 6240 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, 6241 6242 /* 8-bit unsigned value to configure the HE trigger frame MAC padding 6243 * duration. 6244 * This attribute is used to configure the testbed device. 6245 * Uses the enum qca_wlan_he_mac_padding_dur values. 6246 */ 6247 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, 6248 6249 /* 8-bit unsigned value to override the MU EDCA params to defaults 6250 * regardless of the AP beacon MU EDCA params. If it is enabled use 6251 * the default values else use the MU EDCA params from AP beacon. 6252 * This attribute is used to configure the testbed device. 6253 * 1 - enable override, 0 - disable. 6254 */ 6255 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, 6256 6257 /* 8-bit unsigned value to configure the support for receiving 6258 * an MPDU that contains an operating mode control subfield. 6259 * This attribute is used to configure the testbed device. 6260 * 1-enable, 0-disable. 6261 */ 6262 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, 6263 6264 /* Nested attribute values required to setup the TWT session. 6265 * enum qca_wlan_vendor_attr_twt_setup provides the necessary 6266 * information to set up the session. It contains broadcast flags, 6267 * set_up flags, trigger value, flow type, flow ID, wake interval 6268 * exponent, protection, target wake time, wake duration, wake interval 6269 * mantissa. These nested attributes are used to setup a host triggered 6270 * TWT session. 6271 */ 6272 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, 6273 6274 /* This nested attribute is used to terminate the current TWT session. 6275 * It does not currently carry any attributes. 6276 */ 6277 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, 6278 6279 /* This nested attribute is used to suspend the current TWT session. 6280 * It does not currently carry any attributes. 6281 */ 6282 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, 6283 6284 /* Nested attribute values to indicate the request for resume. 6285 * This attribute is used to resume the TWT session. 6286 * enum qca_wlan_vendor_attr_twt_resume provides the necessary 6287 * parameters required to resume the TWT session. 6288 */ 6289 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, 6290 6291 /* 8-bit unsigned value to set the HE operating mode control 6292 * (OM CTRL) Channel Width subfield. 6293 * The Channel Width subfield indicates the operating channel width 6294 * supported by the STA for both reception and transmission. 6295 * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. 6296 * This setting is cleared with the 6297 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 6298 * flag attribute to reset defaults. 6299 * This attribute is used to configure the testbed device. 6300 */ 6301 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, 6302 6303 /* 8-bit unsigned value to configure the number of spatial 6304 * streams in HE operating mode control field. 6305 * This setting is cleared with the 6306 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 6307 * flag attribute to reset defaults. 6308 * This attribute is used to configure the testbed device. 6309 */ 6310 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, 6311 6312 /* Flag attribute to configure the UL MU disable bit in 6313 * HE operating mode control field. 6314 * This setting is cleared with the 6315 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 6316 * flag attribute to reset defaults. 6317 * This attribute is used to configure the testbed device. 6318 */ 6319 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, 6320 6321 /* Flag attribute to clear the previously set HE operating mode 6322 * control field configuration. 6323 * This attribute is used to configure the testbed device to reset 6324 * defaults to clear any previously set HE operating mode control 6325 * field configuration. 6326 */ 6327 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, 6328 6329 /* 8-bit unsigned value to configure HE single user PPDU 6330 * transmission. By default this setting is disabled and it 6331 * is disabled in the reset defaults of the device configuration. 6332 * This attribute is used to configure the testbed device. 6333 * 1-enable, 0-disable 6334 */ 6335 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, 6336 6337 /* 8-bit unsigned value to configure action frame transmission 6338 * in HE trigger based PPDU transmission. 6339 * By default this setting is disabled and it is disabled in 6340 * the reset defaults of the device configuration. 6341 * This attribute is used to configure the testbed device. 6342 * 1-enable, 0-disable 6343 */ 6344 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, 6345 6346 /* Nested attribute to indicate HE operating mode control field 6347 * transmission. It contains operating mode control field Nss, 6348 * channel bandwidth, Tx Nsts and UL MU disable attributes. 6349 * These nested attributes are used to send HE operating mode control 6350 * with configured values. 6351 * Uses the enum qca_wlan_vendor_attr_he_omi_tx attributes. 6352 * This attribute is used to configure the testbed device. 6353 */ 6354 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX = 33, 6355 6356 /* 8-bit unsigned value to configure +HTC_HE support to indicate the 6357 * support for the reception of a frame that carries an HE variant 6358 * HT Control field. 6359 * This attribute is used to configure the testbed device. 6360 * 1-enable, 0-disable 6361 */ 6362 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34, 6363 6364 /* keep last */ 6365 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, 6366 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = 6367 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, 6368 }; 6369 6370 /** 6371 * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for 6372 * TWT (Target Wake Time) setup request. These attributes are sent as part of 6373 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and 6374 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 6375 * 6376 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. 6377 * Disable (flag attribute not present) - Individual TWT 6378 * Enable (flag attribute present) - Broadcast TWT. 6379 * Individual means the session is between the STA and the AP. 6380 * This session is established using a separate negotiation between 6381 * STA and AP. 6382 * Broadcast means the session is across multiple STAs and an AP. The 6383 * configuration parameters are announced in Beacon frames by the AP. 6384 * 6385 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). 6386 * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to 6387 * specify the TWT request type 6388 * 6389 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute 6390 * Enable (flag attribute present) - TWT with trigger support. 6391 * Disable (flag attribute not present) - TWT without trigger support. 6392 * Trigger means the AP will send the trigger frame to allow STA to send data. 6393 * Without trigger, the STA will wait for the MU EDCA timer before 6394 * transmitting the data. 6395 * 6396 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) 6397 * 0 - Announced TWT - In this mode, STA may skip few service periods to 6398 * save more power. If STA wants to wake up, it will send a PS-POLL/QoS 6399 * NULL frame to AP. 6400 * 1 - Unannounced TWT - The STA will wakeup during every SP. 6401 * 6402 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) 6403 * Flow ID is the unique identifier for each TWT session. 6404 * Currently this is not required and dialog ID will be set to zero. 6405 * 6406 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) 6407 * This attribute (exp) is used along with the mantissa to derive the 6408 * wake interval using the following formula: 6409 * pow(2,exp) = wake_intvl_us/wake_intvl_mantis 6410 * Wake interval is the interval between 2 successive SP. 6411 * 6412 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute 6413 * Enable (flag attribute present) - Protection required. 6414 * Disable (flag attribute not present) - Protection not required. 6415 * If protection is enabled, then the AP will use protection 6416 * mechanism using RTS/CTS to self to reserve the airtime. 6417 * 6418 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) 6419 * This attribute is used as the SP offset which is the offset from 6420 * TSF after which the wake happens. The units are in microseconds. If 6421 * this attribute is not provided, then the value will be set to zero. 6422 * 6423 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) 6424 * This is the duration of the service period. The units are in TU. 6425 * 6426 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) 6427 * This attribute is used to configure wake interval mantissa. 6428 * The units are in TU. 6429 */ 6430 enum qca_wlan_vendor_attr_twt_setup { 6431 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, 6432 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, 6433 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, 6434 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, 6435 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, 6436 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, 6437 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, 6438 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, 6439 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, 6440 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, 6441 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, 6442 6443 /* keep last */ 6444 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, 6445 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = 6446 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, 6447 }; 6448 6449 /** 6450 * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for 6451 * TWT (Target Wake Time) resume request. These attributes are sent as part of 6452 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and 6453 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 6454 * 6455 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) 6456 * This attribute is used as the SP offset which is the offset from 6457 * TSF after which the wake happens. The units are in microseconds. 6458 * If this attribute is not provided, then the value will be set to 6459 * zero. 6460 * 6461 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) 6462 * This attribute represents the next TWT subfield size. 6463 */ 6464 enum qca_wlan_vendor_attr_twt_resume { 6465 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, 6466 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, 6467 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, 6468 6469 /* keep last */ 6470 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, 6471 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = 6472 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, 6473 }; 6474 6475 /** 6476 * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) 6477 * Represents the setup type being requested for TWT. 6478 * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT 6479 * parameters but relying on AP to fill the parameters during the negotiation. 6480 * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested 6481 * values which the AP may accept or AP may provide alternative parameters 6482 * which the STA may accept. 6483 * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any 6484 * alternate parameters than the requested ones. 6485 */ 6486 enum qca_wlan_vendor_twt_setup_req_type { 6487 QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, 6488 QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, 6489 QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, 6490 }; 6491 6492 /** 6493 * enum qca_wlan_throughput_level - Current throughput level 6494 * 6495 * Indicates the current level of throughput calculated by driver. The driver 6496 * may choose different thresholds to decide whether the throughput level is 6497 * low or medium or high based on variety of parameters like physical link 6498 * capacity of current connection, number of pakcets being dispatched per 6499 * second etc. The throughput level events might not be consistent with the 6500 * actual current throughput value being observed. 6501 * 6502 * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput 6503 * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput 6504 * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput 6505 */ 6506 enum qca_wlan_throughput_level { 6507 QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, 6508 QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, 6509 QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, 6510 }; 6511 6512 /** 6513 * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to 6514 * report throughput changes from driver to user space. enum values are used 6515 * for NL attributes sent with 6516 * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. 6517 */ 6518 enum qca_wlan_vendor_attr_throughput_change { 6519 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, 6520 /* 6521 * Indicates the direction of throughput in which the change is being 6522 * reported. u8 attribute. Value is 0 for TX and 1 for RX. 6523 */ 6524 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, 6525 6526 /* 6527 * Indicates the newly observed throughput level. 6528 * qca_wlan_throughput_level describes the possible range of values. 6529 * u8 attribute. 6530 */ 6531 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, 6532 6533 /* 6534 * Indicates the driver's guidance on the new value to be set to 6535 * kernel's tcp parameter tcp_limit_output_bytes. u32 attribute. Driver 6536 * may optionally include this attribute. 6537 */ 6538 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, 6539 6540 /* 6541 * Indicates the driver's guidance on the new value to be set to 6542 * kernel's tcp parameter tcp_adv_win_scale. s8 attribute. Possible 6543 * values are from -31 to 31. Driver may optionally include this 6544 * attribute. 6545 */ 6546 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, 6547 6548 /* 6549 * Indicates the driver's guidance on the new value to be set to 6550 * kernel's tcp parameter tcp_delack_seg. u32 attribute. Driver may 6551 * optionally include this attribute. 6552 */ 6553 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, 6554 6555 /* keep last */ 6556 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, 6557 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = 6558 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, 6559 }; 6560 6561 /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute 6562 * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command 6563 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. 6564 */ 6565 enum qca_wlan_nan_ext_subcmd_type { 6566 /* Subcmd of type NAN Enable Request */ 6567 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, 6568 /* Subcmd of type NAN Disable Request */ 6569 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, 6570 }; 6571 6572 /** 6573 * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command 6574 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. 6575 */ 6576 enum qca_wlan_vendor_attr_nan_params { 6577 QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, 6578 /* Carries NAN command for firmware component. Every vendor command 6579 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a 6580 * payload containing the NAN command. NLA_BINARY attribute. 6581 */ 6582 QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, 6583 /* Indicates the type of NAN command sent with 6584 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type 6585 * describes the possible range of values. This attribute is mandatory 6586 * if the command being issued is either 6587 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or 6588 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. 6589 */ 6590 QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, 6591 /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz 6592 * band. This attribute is mandatory when command type is 6593 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. 6594 */ 6595 QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, 6596 /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz 6597 * band. This attribute is optional and should be included when command 6598 * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery 6599 * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. 6600 */ 6601 QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, 6602 6603 /* keep last */ 6604 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, 6605 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = 6606 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 6607 }; 6608 #endif 6609