1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * driver.h -- SoC Regulator driver support. 4 * 5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. 6 * 7 * Author: Liam Girdwood <lrg@slimlogic.co.uk> 8 * 9 * Regulator Driver Interface. 10 */ 11 12 #ifndef __LINUX_REGULATOR_DRIVER_H_ 13 #define __LINUX_REGULATOR_DRIVER_H_ 14 15 #include <linux/device.h> 16 #include <linux/linear_range.h> 17 #include <linux/notifier.h> 18 #include <linux/regulator/consumer.h> 19 #include <linux/ww_mutex.h> 20 21 struct gpio_desc; 22 struct regmap; 23 struct regulator_dev; 24 struct regulator_config; 25 struct regulator_init_data; 26 struct regulator_enable_gpio; 27 28 enum regulator_status { 29 REGULATOR_STATUS_OFF, 30 REGULATOR_STATUS_ON, 31 REGULATOR_STATUS_ERROR, 32 /* fast/normal/idle/standby are flavors of "on" */ 33 REGULATOR_STATUS_FAST, 34 REGULATOR_STATUS_NORMAL, 35 REGULATOR_STATUS_IDLE, 36 REGULATOR_STATUS_STANDBY, 37 /* The regulator is enabled but not regulating */ 38 REGULATOR_STATUS_BYPASS, 39 /* in case that any other status doesn't apply */ 40 REGULATOR_STATUS_UNDEFINED, 41 }; 42 43 enum regulator_detection_severity { 44 /* Hardware shut down voltage outputs if condition is detected */ 45 REGULATOR_SEVERITY_PROT, 46 /* Hardware is probably damaged/inoperable */ 47 REGULATOR_SEVERITY_ERR, 48 /* Hardware is still recoverable but recovery action must be taken */ 49 REGULATOR_SEVERITY_WARN, 50 }; 51 52 /* Initialize struct linear_range for regulators */ 53 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \ 54 LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) 55 56 /** 57 * struct regulator_ops - regulator operations. 58 * 59 * @enable: Configure the regulator as enabled. 60 * @disable: Configure the regulator as disabled. 61 * @is_enabled: Return 1 if the regulator is enabled, 0 if not. 62 * May also return negative errno. 63 * 64 * @set_voltage: Set the voltage for the regulator within the range specified. 65 * The driver should select the voltage closest to min_uV. 66 * @set_voltage_sel: Set the voltage for the regulator using the specified 67 * selector. 68 * @map_voltage: Convert a voltage into a selector 69 * @get_voltage: Return the currently configured voltage for the regulator; 70 * return -ENOTRECOVERABLE if regulator can't be read at 71 * bootup and hasn't been set yet. 72 * @get_voltage_sel: Return the currently configured voltage selector for the 73 * regulator; return -ENOTRECOVERABLE if regulator can't 74 * be read at bootup and hasn't been set yet. 75 * @list_voltage: Return one of the supported voltages, in microvolts; zero 76 * if the selector indicates a voltage that is unusable on this system; 77 * or negative errno. Selectors range from zero to one less than 78 * regulator_desc.n_voltages. Voltages may be reported in any order. 79 * 80 * @set_current_limit: Configure a limit for a current-limited regulator. 81 * The driver should select the current closest to max_uA. 82 * @get_current_limit: Get the configured limit for a current-limited regulator. 83 * @set_input_current_limit: Configure an input limit. 84 * 85 * @set_over_current_protection: Support enabling of and setting limits for over 86 * current situation detection. Detection can be configured for three 87 * levels of severity. 88 * 89 * - REGULATOR_SEVERITY_PROT should automatically shut down the regulator(s). 90 * 91 * - REGULATOR_SEVERITY_ERR should indicate that over-current situation is 92 * caused by an unrecoverable error but HW does not perform 93 * automatic shut down. 94 * 95 * - REGULATOR_SEVERITY_WARN should indicate situation where hardware is 96 * still believed to not be damaged but that a board sepcific 97 * recovery action is needed. If lim_uA is 0 the limit should not 98 * be changed but the detection should just be enabled/disabled as 99 * is requested. 100 * 101 * @set_over_voltage_protection: Support enabling of and setting limits for over 102 * voltage situation detection. Detection can be configured for same 103 * severities as over current protection. Units of uV. 104 * @set_under_voltage_protection: Support enabling of and setting limits for 105 * under voltage situation detection. Detection can be configured for same 106 * severities as over current protection. Units of uV. 107 * @set_thermal_protection: Support enabling of and setting limits for over 108 * temperature situation detection.Detection can be configured for same 109 * severities as over current protection. Units of degree Kelvin. 110 * 111 * @set_active_discharge: Set active discharge enable/disable of regulators. 112 * 113 * @set_mode: Set the configured operating mode for the regulator. 114 * @get_mode: Get the configured operating mode for the regulator. 115 * @get_error_flags: Get the current error(s) for the regulator. 116 * @get_status: Return actual (not as-configured) status of regulator, as a 117 * REGULATOR_STATUS value (or negative errno) 118 * @get_optimum_mode: Get the most efficient operating mode for the regulator 119 * when running with the specified parameters. 120 * @set_load: Set the load for the regulator. 121 * 122 * @set_bypass: Set the regulator in bypass mode. 123 * @get_bypass: Get the regulator bypass mode state. 124 * 125 * @enable_time: Time taken for the regulator voltage output voltage to 126 * stabilise after being enabled, in microseconds. 127 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should 128 * select ramp delay equal to or less than(closest) ramp_delay. 129 * @set_voltage_time: Time taken for the regulator voltage output voltage 130 * to stabilise after being set to a new value, in microseconds. 131 * The function receives the from and to voltage as input, it 132 * should return the worst case. 133 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage 134 * to stabilise after being set to a new value, in microseconds. 135 * The function receives the from and to voltage selector as 136 * input, it should return the worst case. 137 * @set_soft_start: Enable soft start for the regulator. 138 * 139 * @set_suspend_voltage: Set the voltage for the regulator when the system 140 * is suspended. 141 * @set_suspend_enable: Mark the regulator as enabled when the system is 142 * suspended. 143 * @set_suspend_disable: Mark the regulator as disabled when the system is 144 * suspended. 145 * @set_suspend_mode: Set the operating mode for the regulator when the 146 * system is suspended. 147 * @resume: Resume operation of suspended regulator. 148 * @set_pull_down: Configure the regulator to pull down when the regulator 149 * is disabled. 150 * 151 * This struct describes regulator operations which can be implemented by 152 * regulator chip drivers. 153 */ 154 struct regulator_ops { 155 156 /* enumerate supported voltages */ 157 int (*list_voltage) (struct regulator_dev *, unsigned selector); 158 159 /* get/set regulator voltage */ 160 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV, 161 unsigned *selector); 162 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV); 163 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector); 164 int (*get_voltage) (struct regulator_dev *); 165 int (*get_voltage_sel) (struct regulator_dev *); 166 167 /* get/set regulator current */ 168 int (*set_current_limit) (struct regulator_dev *, 169 int min_uA, int max_uA); 170 int (*get_current_limit) (struct regulator_dev *); 171 172 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); 173 int (*set_over_current_protection)(struct regulator_dev *, int lim_uA, 174 int severity, bool enable); 175 int (*set_over_voltage_protection)(struct regulator_dev *, int lim_uV, 176 int severity, bool enable); 177 int (*set_under_voltage_protection)(struct regulator_dev *, int lim_uV, 178 int severity, bool enable); 179 int (*set_thermal_protection)(struct regulator_dev *, int lim, 180 int severity, bool enable); 181 int (*set_active_discharge)(struct regulator_dev *, bool enable); 182 183 /* enable/disable regulator */ 184 int (*enable) (struct regulator_dev *); 185 int (*disable) (struct regulator_dev *); 186 int (*is_enabled) (struct regulator_dev *); 187 188 /* get/set regulator operating mode (defined in consumer.h) */ 189 int (*set_mode) (struct regulator_dev *, unsigned int mode); 190 unsigned int (*get_mode) (struct regulator_dev *); 191 192 /* retrieve current error flags on the regulator */ 193 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags); 194 195 /* Time taken to enable or set voltage on the regulator */ 196 int (*enable_time) (struct regulator_dev *); 197 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay); 198 int (*set_voltage_time) (struct regulator_dev *, int old_uV, 199 int new_uV); 200 int (*set_voltage_time_sel) (struct regulator_dev *, 201 unsigned int old_selector, 202 unsigned int new_selector); 203 204 int (*set_soft_start) (struct regulator_dev *); 205 206 /* report regulator status ... most other accessors report 207 * control inputs, this reports results of combining inputs 208 * from Linux (and other sources) with the actual load. 209 * returns REGULATOR_STATUS_* or negative errno. 210 */ 211 int (*get_status)(struct regulator_dev *); 212 213 /* get most efficient regulator operating mode for load */ 214 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, 215 int output_uV, int load_uA); 216 /* set the load on the regulator */ 217 int (*set_load)(struct regulator_dev *, int load_uA); 218 219 /* control and report on bypass mode */ 220 int (*set_bypass)(struct regulator_dev *dev, bool enable); 221 int (*get_bypass)(struct regulator_dev *dev, bool *enable); 222 223 /* the operations below are for configuration of regulator state when 224 * its parent PMIC enters a global STANDBY/HIBERNATE state */ 225 226 /* set regulator suspend voltage */ 227 int (*set_suspend_voltage) (struct regulator_dev *, int uV); 228 229 /* enable/disable regulator in suspend state */ 230 int (*set_suspend_enable) (struct regulator_dev *); 231 int (*set_suspend_disable) (struct regulator_dev *); 232 233 /* set regulator suspend operating mode (defined in consumer.h) */ 234 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); 235 236 int (*resume)(struct regulator_dev *rdev); 237 238 int (*set_pull_down) (struct regulator_dev *); 239 }; 240 241 /* 242 * Regulators can either control voltage or current. 243 */ 244 enum regulator_type { 245 REGULATOR_VOLTAGE, 246 REGULATOR_CURRENT, 247 }; 248 249 /** 250 * struct regulator_desc - Static regulator descriptor 251 * 252 * Each regulator registered with the core is described with a 253 * structure of this type and a struct regulator_config. This 254 * structure contains the non-varying parts of the regulator 255 * description. 256 * 257 * @name: Identifying name for the regulator. 258 * @supply_name: Identifying the regulator supply 259 * @of_match: Name used to identify regulator in DT. 260 * @of_match_full_name: A flag to indicate that the of_match string, if 261 * present, should be matched against the node full_name. 262 * @regulators_node: Name of node containing regulator definitions in DT. 263 * @of_parse_cb: Optional callback called only if of_match is present. 264 * Will be called for each regulator parsed from DT, during 265 * init_data parsing. 266 * The regulator_config passed as argument to the callback will 267 * be a copy of config passed to regulator_register, valid only 268 * for this particular call. Callback may freely change the 269 * config but it cannot store it for later usage. 270 * Callback should return 0 on success or negative ERRNO 271 * indicating failure. 272 * @id: Numerical identifier for the regulator. 273 * @ops: Regulator operations table. 274 * @irq: Interrupt number for the regulator. 275 * @type: Indicates if the regulator is a voltage or current regulator. 276 * @owner: Module providing the regulator, used for refcounting. 277 * 278 * @continuous_voltage_range: Indicates if the regulator can set any 279 * voltage within constrains range. 280 * @n_voltages: Number of selectors available for ops.list_voltage(). 281 * @n_current_limits: Number of selectors available for current limits 282 * 283 * @min_uV: Voltage given by the lowest selector (if linear mapping) 284 * @uV_step: Voltage increase with each selector (if linear mapping) 285 * @linear_min_sel: Minimal selector for starting linear mapping 286 * @fixed_uV: Fixed voltage of rails. 287 * @ramp_delay: Time to settle down after voltage change (unit: uV/us) 288 * @min_dropout_uV: The minimum dropout voltage this regulator can handle 289 * @linear_ranges: A constant table of possible voltage ranges. 290 * @linear_range_selectors_bitfield: A constant table of voltage range 291 * selectors as bitfield values. If 292 * pickable ranges are used each range 293 * must have corresponding selector here. 294 * @n_linear_ranges: Number of entries in the @linear_ranges (and in 295 * linear_range_selectors_bitfield if used) table(s). 296 * @volt_table: Voltage mapping table (if table based mapping) 297 * @curr_table: Current limit mapping table (if table based mapping) 298 * 299 * @vsel_range_reg: Register for range selector when using pickable ranges 300 * and ``regulator_map_*_voltage_*_pickable`` functions. 301 * @vsel_range_mask: Mask for register bitfield used for range selector 302 * @range_applied_by_vsel: A flag to indicate that changes to vsel_range_reg 303 * are only effective after vsel_reg is written 304 * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*`` 305 * @vsel_mask: Mask for register bitfield used for selector 306 * @vsel_step: Specify the resolution of selector stepping when setting 307 * voltage. If 0, then no stepping is done (requested selector is 308 * set directly), if >0 then the regulator API will ramp the 309 * voltage up/down gradually each time increasing/decreasing the 310 * selector by the specified step value. 311 * @csel_reg: Register for current limit selector using regmap set_current_limit 312 * @csel_mask: Mask for register bitfield used for current limit selector 313 * @apply_reg: Register for initiate voltage change on the output when 314 * using regulator_set_voltage_sel_regmap 315 * @apply_bit: Register bitfield used for initiate voltage change on the 316 * output when using regulator_set_voltage_sel_regmap 317 * @enable_reg: Register for control when using regmap enable/disable ops 318 * @enable_mask: Mask for control when using regmap enable/disable ops 319 * @enable_val: Enabling value for control when using regmap enable/disable ops 320 * @disable_val: Disabling value for control when using regmap enable/disable ops 321 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable 322 * when using regulator_enable_regmap and friends APIs. 323 * @bypass_reg: Register for control when using regmap set_bypass 324 * @bypass_mask: Mask for control when using regmap set_bypass 325 * @bypass_val_on: Enabling value for control when using regmap set_bypass 326 * @bypass_val_off: Disabling value for control when using regmap set_bypass 327 * @active_discharge_off: Enabling value for control when using regmap 328 * set_active_discharge 329 * @active_discharge_on: Disabling value for control when using regmap 330 * set_active_discharge 331 * @active_discharge_mask: Mask for control when using regmap 332 * set_active_discharge 333 * @active_discharge_reg: Register for control when using regmap 334 * set_active_discharge 335 * @soft_start_reg: Register for control when using regmap set_soft_start 336 * @soft_start_mask: Mask for control when using regmap set_soft_start 337 * @soft_start_val_on: Enabling value for control when using regmap 338 * set_soft_start 339 * @pull_down_reg: Register for control when using regmap set_pull_down 340 * @pull_down_mask: Mask for control when using regmap set_pull_down 341 * @pull_down_val_on: Enabling value for control when using regmap 342 * set_pull_down 343 * 344 * @ramp_reg: Register for controlling the regulator ramp-rate. 345 * @ramp_mask: Bitmask for the ramp-rate control register. 346 * @ramp_delay_table: Table for mapping the regulator ramp-rate values. Values 347 * should be given in units of V/S (uV/uS). See the 348 * regulator_set_ramp_delay_regmap(). 349 * @n_ramp_values: number of elements at @ramp_delay_table. 350 * 351 * @enable_time: Time taken for initial enable of regulator (in uS). 352 * @off_on_delay: guard time (in uS), before re-enabling a regulator 353 * 354 * @poll_enabled_time: The polling interval (in uS) to use while checking that 355 * the regulator was actually enabled. Max upto enable_time. 356 * 357 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode 358 */ 359 struct regulator_desc { 360 const char *name; 361 const char *supply_name; 362 const char *of_match; 363 bool of_match_full_name; 364 const char *regulators_node; 365 int (*of_parse_cb)(struct device_node *, 366 const struct regulator_desc *, 367 struct regulator_config *); 368 int id; 369 unsigned int continuous_voltage_range:1; 370 unsigned n_voltages; 371 unsigned int n_current_limits; 372 const struct regulator_ops *ops; 373 int irq; 374 enum regulator_type type; 375 struct module *owner; 376 377 unsigned int min_uV; 378 unsigned int uV_step; 379 unsigned int linear_min_sel; 380 int fixed_uV; 381 unsigned int ramp_delay; 382 int min_dropout_uV; 383 384 const struct linear_range *linear_ranges; 385 const unsigned int *linear_range_selectors_bitfield; 386 387 int n_linear_ranges; 388 389 const unsigned int *volt_table; 390 const unsigned int *curr_table; 391 392 unsigned int vsel_range_reg; 393 unsigned int vsel_range_mask; 394 bool range_applied_by_vsel; 395 unsigned int vsel_reg; 396 unsigned int vsel_mask; 397 unsigned int vsel_step; 398 unsigned int csel_reg; 399 unsigned int csel_mask; 400 unsigned int apply_reg; 401 unsigned int apply_bit; 402 unsigned int enable_reg; 403 unsigned int enable_mask; 404 unsigned int enable_val; 405 unsigned int disable_val; 406 bool enable_is_inverted; 407 unsigned int bypass_reg; 408 unsigned int bypass_mask; 409 unsigned int bypass_val_on; 410 unsigned int bypass_val_off; 411 unsigned int active_discharge_on; 412 unsigned int active_discharge_off; 413 unsigned int active_discharge_mask; 414 unsigned int active_discharge_reg; 415 unsigned int soft_start_reg; 416 unsigned int soft_start_mask; 417 unsigned int soft_start_val_on; 418 unsigned int pull_down_reg; 419 unsigned int pull_down_mask; 420 unsigned int pull_down_val_on; 421 unsigned int ramp_reg; 422 unsigned int ramp_mask; 423 const unsigned int *ramp_delay_table; 424 unsigned int n_ramp_values; 425 426 unsigned int enable_time; 427 428 unsigned int off_on_delay; 429 430 unsigned int poll_enabled_time; 431 432 unsigned int (*of_map_mode)(unsigned int mode); 433 }; 434 435 /** 436 * struct regulator_config - Dynamic regulator descriptor 437 * 438 * Each regulator registered with the core is described with a 439 * structure of this type and a struct regulator_desc. This structure 440 * contains the runtime variable parts of the regulator description. 441 * 442 * @dev: struct device for the regulator 443 * @init_data: platform provided init data, passed through by driver 444 * @driver_data: private regulator data 445 * @of_node: OpenFirmware node to parse for device tree bindings (may be 446 * NULL). 447 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is 448 * insufficient. 449 * @ena_gpiod: GPIO controlling regulator enable. 450 */ 451 struct regulator_config { 452 struct device *dev; 453 const struct regulator_init_data *init_data; 454 void *driver_data; 455 struct device_node *of_node; 456 struct regmap *regmap; 457 458 struct gpio_desc *ena_gpiod; 459 }; 460 461 /** 462 * struct regulator_err_state - regulator error/notification status 463 * 464 * @rdev: Regulator which status the struct indicates. 465 * @notifs: Events which have occurred on the regulator. 466 * @errors: Errors which are active on the regulator. 467 * @possible_errs: Errors which can be signaled (by given IRQ). 468 */ 469 struct regulator_err_state { 470 struct regulator_dev *rdev; 471 unsigned long notifs; 472 unsigned long errors; 473 int possible_errs; 474 }; 475 476 /** 477 * struct regulator_irq_data - regulator error/notification status data 478 * 479 * @states: Status structs for each of the associated regulators. 480 * @num_states: Amount of associated regulators. 481 * @data: Driver data pointer given at regulator_irq_desc. 482 * @opaque: Value storage for IC driver. Core does not update this. ICs 483 * may want to store status register value here at map_event and 484 * compare contents at 'renable' callback to see if new problems 485 * have been added to status. If that is the case it may be 486 * desirable to return REGULATOR_ERROR_CLEARED and not 487 * REGULATOR_ERROR_ON to allow IRQ fire again and to generate 488 * notifications also for the new issues. 489 * 490 * This structure is passed to 'map_event' and 'renable' callbacks for 491 * reporting regulator status to core. 492 */ 493 struct regulator_irq_data { 494 struct regulator_err_state *states; 495 int num_states; 496 void *data; 497 long opaque; 498 }; 499 500 /** 501 * struct regulator_irq_desc - notification sender for IRQ based events. 502 * 503 * @name: The visible name for the IRQ 504 * @fatal_cnt: If this IRQ is used to signal HW damaging condition it may be 505 * best to shut-down regulator(s) or reboot the SOC if error 506 * handling is repeatedly failing. If fatal_cnt is given the IRQ 507 * handling is aborted if it fails for fatal_cnt times and die() 508 * callback (if populated) is called. If die() is not populated 509 * poweroff for the system is attempted in order to prevent any 510 * further damage. 511 * @reread_ms: The time which is waited before attempting to re-read status 512 * at the worker if IC reading fails. Immediate re-read is done 513 * if time is not specified. 514 * @irq_off_ms: The time which IRQ is kept disabled before re-evaluating the 515 * status for devices which keep IRQ disabled for duration of the 516 * error. If this is not given the IRQ is left enabled and renable 517 * is not called. 518 * @skip_off: If set to true the IRQ handler will attempt to check if any of 519 * the associated regulators are enabled prior to taking other 520 * actions. If no regulators are enabled and this is set to true 521 * a spurious IRQ is assumed and IRQ_NONE is returned. 522 * @high_prio: Boolean to indicate that high priority WQ should be used. 523 * @data: Driver private data pointer which will be passed as such to 524 * the renable, map_event and die callbacks in regulator_irq_data. 525 * @die: Protection callback. If IC status reading or recovery actions 526 * fail fatal_cnt times this callback is called or system is 527 * powered off. This callback should implement a final protection 528 * attempt like disabling the regulator. If protection succeeded 529 * die() may return 0. If anything else is returned the core 530 * assumes final protection failed and attempts to perform a 531 * poweroff as a last resort. 532 * @map_event: Driver callback to map IRQ status into regulator devices with 533 * events / errors. NOTE: callback MUST initialize both the 534 * errors and notifs for all rdevs which it signals having 535 * active events as core does not clean the map data. 536 * REGULATOR_FAILED_RETRY can be returned to indicate that the 537 * status reading from IC failed. If this is repeated for 538 * fatal_cnt times the core will call die() callback or power-off 539 * the system as a last resort to protect the HW. 540 * @renable: Optional callback to check status (if HW supports that) before 541 * re-enabling IRQ. If implemented this should clear the error 542 * flags so that errors fetched by regulator_get_error_flags() 543 * are updated. If callback is not implemented then errors are 544 * assumed to be cleared and IRQ is re-enabled. 545 * REGULATOR_FAILED_RETRY can be returned to 546 * indicate that the status reading from IC failed. If this is 547 * repeated for 'fatal_cnt' times the core will call die() 548 * callback or if die() is not populated then attempt to power-off 549 * the system as a last resort to protect the HW. 550 * Returning zero indicates that the problem in HW has been solved 551 * and IRQ will be re-enabled. Returning REGULATOR_ERROR_ON 552 * indicates the error condition is still active and keeps IRQ 553 * disabled. Please note that returning REGULATOR_ERROR_ON does 554 * not retrigger evaluating what events are active or resending 555 * notifications. If this is needed you probably want to return 556 * zero and allow IRQ to retrigger causing events to be 557 * re-evaluated and re-sent. 558 * 559 * This structure is used for registering regulator IRQ notification helper. 560 */ 561 struct regulator_irq_desc { 562 const char *name; 563 int fatal_cnt; 564 int reread_ms; 565 int irq_off_ms; 566 bool skip_off; 567 bool high_prio; 568 void *data; 569 570 int (*die)(struct regulator_irq_data *rid); 571 int (*map_event)(int irq, struct regulator_irq_data *rid, 572 unsigned long *dev_mask); 573 int (*renable)(struct regulator_irq_data *rid); 574 }; 575 576 /* 577 * Return values for regulator IRQ helpers. 578 */ 579 enum { 580 REGULATOR_ERROR_CLEARED, 581 REGULATOR_FAILED_RETRY, 582 REGULATOR_ERROR_ON, 583 }; 584 585 /* 586 * struct coupling_desc 587 * 588 * Describes coupling of regulators. Each regulator should have 589 * at least a pointer to itself in coupled_rdevs array. 590 * When a new coupled regulator is resolved, n_resolved is 591 * incremented. 592 */ 593 struct coupling_desc { 594 struct regulator_dev **coupled_rdevs; 595 struct regulator_coupler *coupler; 596 int n_resolved; 597 int n_coupled; 598 }; 599 600 /* 601 * struct regulator_dev 602 * 603 * Voltage / Current regulator class device. One for each 604 * regulator. 605 * 606 * This should *not* be used directly by anything except the regulator 607 * core and notification injection (which should take the mutex and do 608 * no other direct access). 609 */ 610 struct regulator_dev { 611 const struct regulator_desc *desc; 612 int exclusive; 613 u32 use_count; 614 u32 open_count; 615 u32 bypass_count; 616 617 /* lists we belong to */ 618 struct list_head list; /* list of all regulators */ 619 620 /* lists we own */ 621 struct list_head consumer_list; /* consumers we supply */ 622 623 struct coupling_desc coupling_desc; 624 625 struct blocking_notifier_head notifier; 626 struct ww_mutex mutex; /* consumer lock */ 627 struct task_struct *mutex_owner; 628 int ref_cnt; 629 struct module *owner; 630 struct device dev; 631 struct regulation_constraints *constraints; 632 struct regulator *supply; /* for tree */ 633 const char *supply_name; 634 struct regmap *regmap; 635 636 struct delayed_work disable_work; 637 638 void *reg_data; /* regulator_dev data */ 639 640 struct dentry *debugfs; 641 642 struct regulator_enable_gpio *ena_pin; 643 unsigned int ena_gpio_state:1; 644 645 unsigned int is_switch:1; 646 647 /* time when this regulator was disabled last time */ 648 ktime_t last_off; 649 int cached_err; 650 bool use_cached_err; 651 spinlock_t err_lock; 652 }; 653 654 /* 655 * Convert error flags to corresponding notifications. 656 * 657 * Can be used by drivers which use the notification helpers to 658 * find out correct notification flags based on the error flags. Drivers 659 * can avoid storing both supported notification and error flags which 660 * may save few bytes. 661 */ regulator_err2notif(int err)662 static inline int regulator_err2notif(int err) 663 { 664 switch (err) { 665 case REGULATOR_ERROR_UNDER_VOLTAGE: 666 return REGULATOR_EVENT_UNDER_VOLTAGE; 667 case REGULATOR_ERROR_OVER_CURRENT: 668 return REGULATOR_EVENT_OVER_CURRENT; 669 case REGULATOR_ERROR_REGULATION_OUT: 670 return REGULATOR_EVENT_REGULATION_OUT; 671 case REGULATOR_ERROR_FAIL: 672 return REGULATOR_EVENT_FAIL; 673 case REGULATOR_ERROR_OVER_TEMP: 674 return REGULATOR_EVENT_OVER_TEMP; 675 case REGULATOR_ERROR_UNDER_VOLTAGE_WARN: 676 return REGULATOR_EVENT_UNDER_VOLTAGE_WARN; 677 case REGULATOR_ERROR_OVER_CURRENT_WARN: 678 return REGULATOR_EVENT_OVER_CURRENT_WARN; 679 case REGULATOR_ERROR_OVER_VOLTAGE_WARN: 680 return REGULATOR_EVENT_OVER_VOLTAGE_WARN; 681 case REGULATOR_ERROR_OVER_TEMP_WARN: 682 return REGULATOR_EVENT_OVER_TEMP_WARN; 683 } 684 return 0; 685 } 686 687 688 struct regulator_dev * 689 regulator_register(struct device *dev, 690 const struct regulator_desc *regulator_desc, 691 const struct regulator_config *config); 692 struct regulator_dev * 693 devm_regulator_register(struct device *dev, 694 const struct regulator_desc *regulator_desc, 695 const struct regulator_config *config); 696 void regulator_unregister(struct regulator_dev *rdev); 697 698 int regulator_notifier_call_chain(struct regulator_dev *rdev, 699 unsigned long event, void *data); 700 void *devm_regulator_irq_helper(struct device *dev, 701 const struct regulator_irq_desc *d, int irq, 702 int irq_flags, int common_errs, 703 int *per_rdev_errs, struct regulator_dev **rdev, 704 int rdev_amount); 705 void *regulator_irq_helper(struct device *dev, 706 const struct regulator_irq_desc *d, int irq, 707 int irq_flags, int common_errs, int *per_rdev_errs, 708 struct regulator_dev **rdev, int rdev_amount); 709 void regulator_irq_helper_cancel(void **handle); 710 int regulator_irq_map_event_simple(int irq, struct regulator_irq_data *rid, 711 unsigned long *dev_mask); 712 713 void *rdev_get_drvdata(struct regulator_dev *rdev); 714 struct device *rdev_get_dev(struct regulator_dev *rdev); 715 struct regmap *rdev_get_regmap(struct regulator_dev *rdev); 716 int rdev_get_id(struct regulator_dev *rdev); 717 718 int regulator_mode_to_status(unsigned int); 719 720 int regulator_list_voltage_linear(struct regulator_dev *rdev, 721 unsigned int selector); 722 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev, 723 unsigned int selector); 724 int regulator_list_voltage_linear_range(struct regulator_dev *rdev, 725 unsigned int selector); 726 int regulator_list_voltage_table(struct regulator_dev *rdev, 727 unsigned int selector); 728 int regulator_map_voltage_linear(struct regulator_dev *rdev, 729 int min_uV, int max_uV); 730 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev, 731 int min_uV, int max_uV); 732 int regulator_map_voltage_linear_range(struct regulator_dev *rdev, 733 int min_uV, int max_uV); 734 int regulator_map_voltage_iterate(struct regulator_dev *rdev, 735 int min_uV, int max_uV); 736 int regulator_map_voltage_ascend(struct regulator_dev *rdev, 737 int min_uV, int max_uV); 738 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev); 739 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev, 740 unsigned int sel); 741 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev); 742 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel); 743 int regulator_is_enabled_regmap(struct regulator_dev *rdev); 744 int regulator_enable_regmap(struct regulator_dev *rdev); 745 int regulator_disable_regmap(struct regulator_dev *rdev); 746 int regulator_set_voltage_time_sel(struct regulator_dev *rdev, 747 unsigned int old_selector, 748 unsigned int new_selector); 749 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable); 750 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable); 751 int regulator_set_soft_start_regmap(struct regulator_dev *rdev); 752 int regulator_set_pull_down_regmap(struct regulator_dev *rdev); 753 754 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, 755 bool enable); 756 int regulator_set_current_limit_regmap(struct regulator_dev *rdev, 757 int min_uA, int max_uA); 758 int regulator_get_current_limit_regmap(struct regulator_dev *rdev); 759 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); 760 int regulator_find_closest_bigger(unsigned int target, const unsigned int *table, 761 unsigned int num_sel, unsigned int *sel); 762 int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay); 763 int regulator_sync_voltage_rdev(struct regulator_dev *rdev); 764 765 /* 766 * Helper functions intended to be used by regulator drivers prior registering 767 * their regulators. 768 */ 769 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, 770 unsigned int selector); 771 772 int regulator_desc_list_voltage_linear(const struct regulator_desc *desc, 773 unsigned int selector); 774 775 #ifdef CONFIG_REGULATOR 776 const char *rdev_get_name(struct regulator_dev *rdev); 777 #else rdev_get_name(struct regulator_dev * rdev)778 static inline const char *rdev_get_name(struct regulator_dev *rdev) 779 { 780 return NULL; 781 } 782 #endif 783 784 #endif 785