| /linux-6.12.1/Documentation/userspace-api/media/rc/ |
| D | lirc-get-send-mode.rst | 34 The mode used for transmitting.
65 - Device does not support transmitting.
|
| D | lirc-get-features.rst | 52 :ref:`LIRC_MODE_PULSE <lirc-mode-pulse>` can only be used for transmitting.
|
| /linux-6.12.1/drivers/media/cec/core/ |
| D | cec-adap.c | 360 if (adap->transmitting == data) { in cec_data_cancel()
361 adap->transmitting = NULL; in cec_data_cancel()
412 if (adap->transmitting) in cec_flush()
495 if (adap->transmitting) in cec_thread_func()
496 cec_data_cancel(adap->transmitting, in cec_thread_func()
512 if (adap->transmitting) { in cec_thread_func()
514 adap->transmitting->msg.len, in cec_thread_func()
515 adap->transmitting->msg.msg); in cec_thread_func()
517 cec_data_cancel(adap->transmitting, in cec_thread_func()
542 adap->transmitting = data; in cec_thread_func()
[all …]
|
| /linux-6.12.1/drivers/net/team/ |
| D | Kconfig | 33 Basic mode where port used for transmitting packets is selected in
45 Basic mode where port used for transmitting packets is selected
|
| /linux-6.12.1/drivers/media/rc/ |
| D | redrat3.c | 224 bool transmitting; member
238 if (!rr3->transmitting && (code != 0x40)) in redrat3_dump_fw_error()
276 if (!rr3->transmitting) in redrat3_dump_fw_error()
760 if (rr3->transmitting) { in redrat3_transmit_ir()
769 rr3->transmitting = true; in redrat3_transmit_ir()
846 rr3->transmitting = false; in redrat3_transmit_ir()
|
| D | ite-cir.c | 181 bool for_tx = dev->transmitting; in ite_set_carrier_params()
348 dev->transmitting = true; in ite_tx_ir()
458 dev->transmitting = false; in ite_tx_ir()
1198 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_close()
1452 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_suspend()
|
| D | ite-cir.h | 84 bool transmitting; member
|
| /linux-6.12.1/drivers/usb/class/ |
| D | cdc-acm.h | 78 int transmitting; member
|
| /linux-6.12.1/Documentation/scsi/ |
| D | cxgb3i.rst | 18 On transmitting, Chelsio S3 h/w computes and inserts the Header and
32 On transmitting, S3 h/w accepts the complete PDU (header + data)
|
| /linux-6.12.1/Documentation/devicetree/bindings/media/ |
| D | st-rc.txt | 14 protocol used for transmitting remote control signals. tx-mode should
|
| /linux-6.12.1/drivers/net/hippi/ |
| D | Kconfig | 36 transmitting and receiving. This memory cannot be used by any other
|
| /linux-6.12.1/Documentation/bpf/ |
| D | redirect.rst | 28 Not all drivers support transmitting frames after a redirect, and for
|
| /linux-6.12.1/Documentation/userspace-api/media/cec/ |
| D | cec-pin-error-inj.rst | 93 receiving CEC messages and those relating to transmitting CEC messages. In
158 keeps transmitting after the first byte was NACKed.
190 stop transmitting ('Arbitration Lost'). This is very hard to test,
200 This setting changes the behavior of transmitting CEC messages. Normally
293 Just stop transmitting after this bit. If <op> specifies a specific CEC
|
| D | cec-ioc-receive.rst | 148 transmitting the message. Ignored by :ref:`ioctl CEC_RECEIVE <CEC_RECEIVE>`.
176 transmitting the Poll message.
227 - Normally CEC messages are validated before transmitting them. If this
|
| /linux-6.12.1/Documentation/userspace-api/media/drivers/ |
| D | cx2341x-uapi.rst | 23 transmitting this block the first line of the block on the right to the
31 second line of 8 UV pairs of the top-left block, etc. After transmitting
|
| /linux-6.12.1/Documentation/networking/ |
| D | xsk-tx-metadata.rst | 7 This document describes how to enable offloads when transmitting packets
|
| /linux-6.12.1/Documentation/input/ |
| D | userio.rst | 61 Registers the port with the serio driver and begins transmitting data back and
|
| /linux-6.12.1/Documentation/networking/mac80211_hwsim/ |
| D | mac80211_hwsim.rst | 44 currently enabled and on the same channel as the transmitting
|
| /linux-6.12.1/Documentation/networking/caif/ |
| D | caif.rst | 132 might be problems transmitting over UART.
|
| D | linux_caif.rst | 85 - When receiving / transmitting CAIF Packets (cfpkt), ownership is passed
|
| /linux-6.12.1/include/media/ |
| D | cec.h | 245 struct cec_data *transmitting; member
|
| /linux-6.12.1/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 205 When transmitting synchronous data the allocated channel width needs to be
223 When transmitting isochronous AVP data the desired packet size needs to be
|
| /linux-6.12.1/Documentation/userspace-api/media/v4l/ |
| D | dev-rds.rst | 13 at devices capable of receiving and/or transmitting RDS information.
|
| /linux-6.12.1/Documentation/driver-api/ |
| D | slimbus.rst | 36 Framer device is responsible for clocking the bus, and transmitting frame-sync
|
| /linux-6.12.1/Documentation/ABI/testing/ |
| D | sysfs-class-net-cdc_ncm | 76 aggregate before transmitting an NTB frame.
|