| /linux-6.12.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mm-venice-gw73xx-0x-rs485.dtso | 10 * - RS485_EN needs to be pulled high
11 * - RS485_HALF needs to be pulled high
|
| D | imx8mm-venice-gw72xx-0x-rs485.dtso | 10 * - RS485_EN needs to be pulled high
11 * - RS485_HALF needs to be pulled high
|
| D | imx8mm-venice-gw72xx-0x-rs422.dtso | 10 * - RS485_EN needs to be pulled high
|
| D | imx8mm-venice-gw73xx-0x-rs422.dtso | 10 * - RS485_EN needs to be pulled high
|
| /linux-6.12.1/drivers/net/ethernet/intel/fm10k/ |
| D | fm10k_mbx.c | 349 end = fm10k_fifo_head_offset(fifo, mbx->pulled); in fm10k_mbx_write_copy()
389 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_pull_head()
393 len = fm10k_fifo_used(fifo) - mbx->pulled; in fm10k_mbx_pull_head()
403 len && (mbx->pulled >= len); in fm10k_mbx_pull_head()
405 mbx->pulled -= fm10k_fifo_head_drop(fifo); in fm10k_mbx_pull_head()
622 head = fm10k_fifo_head_offset(&mbx->tx, mbx->pulled); in fm10k_mbx_update_local_crc()
863 crc = fm10k_fifo_crc(fifo, fm10k_fifo_head_offset(fifo, mbx->pulled), in fm10k_mbx_create_data_hdr()
1068 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_reset_work()
1071 while (fm10k_fifo_head_len(&mbx->tx) && mbx->pulled) { in fm10k_mbx_reset_work()
1074 if (mbx->pulled >= len) in fm10k_mbx_reset_work()
[all …]
|
| D | fm10k_mbx.h | 266 u16 tail, tail_len, pulled; member
|
| /linux-6.12.1/Documentation/devicetree/bindings/gpio/ |
| D | gpio-max3191x.txt | 31 pulled high (8-bit mode). Use this if the modesel pin
35 that modesel is pulled low (16-bit mode).
|
| /linux-6.12.1/arch/powerpc/boot/dts/fsl/ |
| D | p1023rdb.dts | 186 /* IRQ[0:3] are pulled up on board, set to active-low */
212 * IRQ[7] is pulled up on board, set to active-low
238 * IRQ[8:10] are pulled up on board, set to active-low
|
| /linux-6.12.1/Documentation/dev-tools/ |
| D | index.rst | 6 be used to work on the kernel. For now, the documents have been pulled
|
| /linux-6.12.1/arch/arm64/boot/dts/qcom/ |
| D | sdm845-db845c-navigation-mezzanine.dts | 87 * vreg_s4a_1p8 trace is pulled high.
|
| /linux-6.12.1/arch/arm/boot/dts/intel/pxa/ |
| D | pxa3xx.dtsi | 88 * the configured driven and pulled levels match, so if there is a need for
89 * non-LPM pulled output, the same configuration could probably be used.
|
| /linux-6.12.1/arch/arm/boot/dts/allwinner/ |
| D | sunxi-d1s-t113-mangopi-mq-r.dtsi | 117 /* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
|
| D | sun4i-a10-pcduino2.dts | 47 * is controlled by the PD2 pin (pulled-up by default). Also one of
|
| /linux-6.12.1/tools/power/pm-graph/config/ |
| D | custom-timeline-functions.cfg | 78 # The args are pulled directly from the stack using this architecture's registers
143 # The args are pulled directly from the stack using this architecture's registers
|
| /linux-6.12.1/Documentation/devicetree/bindings/mfd/ |
| D | tps6507x.txt | 29 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
|
| /linux-6.12.1/arch/arm64/boot/dts/allwinner/ |
| D | sun50i-h618-longanpi-3h.dts | 127 * is not implemented: both CC pins are pulled to GND.
|
| D | sun50i-h616-orangepi-zero.dtsi | 115 * is not implemented: both CC pins are pulled to GND.
|
| D | sun50i-h618-orangepi-zero2w.dts | 165 * is not implemented: both CC pins are pulled to GND.
|
| /linux-6.12.1/Documentation/fb/ |
| D | metronomefb.rst | 17 The display and error status are each pulled through individual GPIOs.
|
| /linux-6.12.1/arch/arm64/boot/dts/rockchip/ |
| D | rk3566-quartz64-b.dts | 464 /* i2c2_m1 exposed on csi port, pulled up to vcc_3v3 */
471 /* i2c3_m1 exposed on dsi port, pulled up to vcc_3v3 */
479 * i2c4_m0 is exposed on PI40, pulled up to vcc_3v3
|
| /linux-6.12.1/arch/arm/boot/dts/ti/omap/ |
| D | am335x-bonegreen-wireless.dts | 112 /* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
|
| /linux-6.12.1/arch/arm/boot/dts/st/ |
| D | stm32mp15xx-dhcom-drc02.dtsi | 59 * pulled high in order to be detected by the USB Controller.
|
| /linux-6.12.1/Documentation/maintainer/ |
| D | rebasing-and-merging.rst | 49 should usually not be changed. Others may have pulled a copy of your
62 have pulled changes from another developer's repository, you are now a
197 tree fails to be pulled upstream, whatever problems it had will block the
|
| /linux-6.12.1/Documentation/process/ |
| D | 7.AdvancedTopics.rst | 53 will, of course, need a server that can be pulled from. Setting up such a
85 have pulled into their repositories, you will make life much more difficult
119 can affect your ability to get trees pulled in the future. Quoting Linus:
|
| /linux-6.12.1/Documentation/scsi/ |
| D | lpfc.rst | 32 received from the midlayer. In the cases where a cable was pulled, link
|