Searched refs:operate (Results 1 – 25 of 209) sorted by relevance
123456789
| /linux-6.12.1/Documentation/arch/mips/ |
| D | ingenic-tcu.rst | 29 operate.
35 - On the oldest SoCs (up to JZ4740), all of the eight channels operate in
37 - On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
38 - On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
39 others operate as TCU1.
|
| /linux-6.12.1/drivers/firmware/arm_scmi/transports/ |
| D | Kconfig | 57 If you want the SCMI SMC based transport to operate in atomic
61 transport to optionally ask for atomic SCMI transactions and operate
114 If you want the SCMI VirtIO based transport to operate in atomic
119 transport to optionally ask for atomic SCMI transactions and operate
|
| /linux-6.12.1/Documentation/devicetree/bindings/mtd/ |
| D | microchip,mchp23k256.txt | 8 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
|
| /linux-6.12.1/drivers/dma/amd/ |
| D | Kconfig | 12 operate on instructions (descriptors) provided by the host operating
|
| /linux-6.12.1/Documentation/arch/sh/ |
| D | booting.rst | 9 inter-operate with old bootloaders must either use a builtin DTB or
|
| /linux-6.12.1/Documentation/scsi/ |
| D | bnx2fc.rst | 13 depend on the state of the network interfaces to operate. As such, the network
28 2. Configure the interfaces on which bnx2fc driver has to operate on.
|
| /linux-6.12.1/Documentation/devicetree/bindings/ipmi/ |
| D | aspeed,ast2400-ibt-bmc.txt | 19 interrupt, the driver will operate in poll mode.
|
| /linux-6.12.1/drivers/pci/endpoint/ |
| D | Kconfig | 14 controller that can operate in endpoint mode.
|
| /linux-6.12.1/drivers/usb/dwc2/ |
| D | Kconfig | 35 driver to operate in Host-only mode.
45 driver to operate in Peripheral-only mode. This option requires
|
| /linux-6.12.1/Documentation/devicetree/bindings/timer/ |
| D | ti,keystone-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| /linux-6.12.1/Documentation/driver-api/ |
| D | mailbox.rst | 43 The client might want to operate in blocking mode (synchronously
106 dc_sync->cl.tx_done = NULL; /* operate in blocking mode */
|
| /linux-6.12.1/fs/sysfs/ |
| D | Kconfig | 16 Some system agents rely on the information in sysfs to operate.
|
| /linux-6.12.1/Documentation/arch/x86/ |
| D | shstk.rst | 59 are only supported in 64 bit user applications. These operate on the features
65 Enable a single feature specified in 'feature'. Can only operate on
69 Disable a single feature specified in 'feature'. Can only operate on
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/can/ |
| D | tcan4x5x.txt | 15 operate at should be less than or equal to 18 MHz.
|
| /linux-6.12.1/Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-st.txt | 7 the DT and operate in the usual way.
|
| /linux-6.12.1/Documentation/mm/damon/ |
| D | index.rst | 18 Using this framework, therefore, the kernel can operate system in an
|
| /linux-6.12.1/Documentation/i2c/busses/ |
| D | i2c-taos-evm.rst | 47 to operate at 1200 bps. However, I don't think this is a big concern in
|
| /linux-6.12.1/drivers/net/wireless/ath/wil6210/ |
| D | Kconfig | 24 ISR registers on wil6210 chip may operate in either
|
| /linux-6.12.1/Documentation/power/ |
| D | opp.rst | 70 As the system proceeds to operate, SoC framework may choose to make certain
77 operational functions operate only on available opps:
152 /* dont operate on the pointer.. just do a sanity check.. */
347 for the OPP library to operate on. Pointer to this structure is
|
| /linux-6.12.1/Documentation/w1/masters/ |
| D | w1-uart.rst | 19 In short, the UART peripheral must support full-duplex and operate in
|
| /linux-6.12.1/arch/m68k/ |
| D | Kconfig.bus | 54 operate ISA cards on Atari. Only 8 bit cards are supported, and
|
| /linux-6.12.1/Documentation/hwmon/ |
| D | ads7828.rst | 56 It can operate in single ended mode (8 +ve inputs) or in differential mode,
|
| D | max31827.rst | 44 configured to operate in the same manner with 1 write operation to the
128 pin is an open-drain output and requires a pullup resistor to operate.
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 40 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
|
| /linux-6.12.1/Documentation/networking/ |
| D | batman-adv.rst | 8 operate on the IP basis. Unlike the batman daemon, which exchanges information
30 batman-adv can operate. The batman-adv soft-interface can be created using the
|
123456789