Searched refs:fiber (Results 1 – 19 of 19) sorted by relevance
| /linux-6.12.1/Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 40 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
42 Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
44 registers whether the PHY is in fiber mode, so this boolean device tree
47 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| D | keystone-netcp.txt | 101 - mac<->fiber mode: 3
|
| /linux-6.12.1/drivers/net/fddi/ |
| D | Kconfig | 12 run over copper or fiber. If you are connected to such a network and
23 This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber)
|
| /linux-6.12.1/drivers/net/ethernet/alacritech/ |
| D | Kconfig | 24 both copper and fiber.
|
| /linux-6.12.1/drivers/net/hippi/ |
| D | Kconfig | 12 can run over copper (25m) or fiber (300m on multi-mode or 10km on
|
| /linux-6.12.1/drivers/net/phy/ |
| D | marvell.c | 1624 int fiber, int status) in marvell_read_status_page_an() argument
1653 if (!fiber) { in marvell_read_status_page_an()
1695 int fiber; in marvell_read_status_page() local
1714 fiber = 1; in marvell_read_status_page()
1716 fiber = 0; in marvell_read_status_page()
1723 phydev->port = fiber ? PORT_FIBRE : PORT_TP; in marvell_read_status_page()
1726 err = marvell_read_status_page_an(phydev, fiber, status); in marvell_read_status_page()
|
| D | Kconfig | 417 fiber connections.
|
| /linux-6.12.1/arch/arm64/boot/dts/hisilicon/ |
| D | hip06.dtsi | 579 media-type = "fiber";
587 media-type = "fiber";
|
| D | hip07.dtsi | 1488 media-type = "fiber";
1498 media-type = "fiber";
|
| /linux-6.12.1/drivers/net/dsa/microchip/ |
| D | ksz8.c | 1151 if (dev->ports[port].fiber) in ksz8_w_phy_bmcr()
1709 p->fiber = 1; in ksz8_config_cpu_port()
1711 if (p->fiber) in ksz8_config_cpu_port()
|
| D | ksz_common.h | 124 u32 fiber:1; /* port is fiber */ member
|
| /linux-6.12.1/Documentation/networking/device_drivers/ethernet/intel/ |
| D | e1000e.rst | 327 between copper-based adapters and fiber-based adapters.
349 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | e1000.rst | 341 If the board uses a fiber interface, these keywords are ignored, and the
342 fiber interface board only links at 1000 Mbps full-duplex.
|
| D | i40e.rst | 370 between copper-based adapters and fiber-based adapters.
395 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | ixgbe.rst | 100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
|
| D | ice.rst | 675 between copper-based adapters and fiber-based adapters.
|
| /linux-6.12.1/Documentation/networking/device_drivers/ethernet/dlink/ |
| D | dl2k.rst | 232 available for fiber adapter.
|
| /linux-6.12.1/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 11 fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
| /linux-6.12.1/Documentation/networking/device_drivers/ethernet/cirrus/ |
| D | cs89x0.rst | 71 or fiber networks).
|