| /linux-6.12.1/net/core/ |
| D | failover.c | 23 struct failover *failover; in failover_get_bymac() local
26 list_for_each_entry(failover, &failover_list, list) { in failover_get_bymac()
27 failover_dev = rtnl_dereference(failover->failover_dev); in failover_get_bymac()
29 *ops = rtnl_dereference(failover->ops); in failover_get_bymac()
242 struct failover *failover_register(struct net_device *dev, in failover_register()
245 struct failover *failover; in failover_register() local
250 failover = kzalloc(sizeof(*failover), GFP_KERNEL); in failover_register()
251 if (!failover) in failover_register()
254 rcu_assign_pointer(failover->ops, ops); in failover_register()
255 netdev_hold(dev, &failover->dev_tracker, GFP_KERNEL); in failover_register()
[all …]
|
| D | Makefile | 41 obj-$(CONFIG_FAILOVER) += failover.o
|
| /linux-6.12.1/include/net/ |
| D | failover.h | 25 struct failover { struct
32 struct failover *failover_register(struct net_device *dev, argument
34 void failover_unregister(struct failover *failover);
|
| D | net_failover.h | 30 struct failover *net_failover_create(struct net_device *standby_dev);
31 void net_failover_destroy(struct failover *failover);
|
| /linux-6.12.1/Documentation/networking/ |
| D | net_failover.rst | 10 The net_failover driver provides an automated failover mechanism via APIs
11 to create and destroy a failover master netdev and manages a primary and
12 standby slave netdevs that get registered via the generic failover
15 The failover netdev acts a master device and controls 2 slave devices. The
18 netdev. Both 'standby' and 'failover' netdevs are associated with the same
19 'pci' device. The user accesses the network interface via 'failover' netdev.
20 The 'failover' netdev chooses 'primary' netdev as default for transmits when
63 virtio-net device is set to 'down' to ensure that the 'failover' netdev prefers
87 Here, ens10 is the 'failover' master interface, ens10nsby is the slave 'standby'
92 device; and on the first boot, the VM might end up with both 'failover' device
[all …]
|
| D | failover.rst | 10 The failover module provides a generic interface for paravirtual drivers
11 to register a netdev and a set of ops with a failover instance. The ops
14 with the same mac address as the failover netdev.
|
| D | index.rst | 26 failover
|
| D | xfrm_sync.rst | 20 with as minimal loss at failover time.
33 note that: lifetime time limit is not important if you assume the failover
|
| D | bonding.rst | 244 The bandwidth and count selection policies permit failover of
441 In order to provide orderly failover semantics, backup interfaces
490 address of the bond changes during a failover.
520 failover time (and the formerly active slave receives
621 In bonding version 2.6.2 or later, when a failover
763 failover event. As soon as the link is up on the new slave
790 Advertisement) when they are issued after a failover event.
1018 hash to load-balance traffic per-vlan, with failover
1036 a failover event. One membership report is issued immediately after
1037 the failover, subsequent packets are sent in each 200ms interval.
[all …]
|
| D | ip-sysctl.rst | 2936 https://datatracker.ietf.org/doc/draft-ietf-tsvwg-sctp-failover for
3041 setting is primarily used to enable fast failover mechanisms without
3043 http://www.ietf.org/id/draft-nishida-tsvwg-sctp-failover-05.txt
|
| /linux-6.12.1/drivers/net/ |
| D | net_failover.c | 706 struct failover *net_failover_create(struct net_device *standby_dev) in net_failover_create()
710 struct failover *failover; in net_failover_create() local
760 failover = failover_register(failover_dev, &net_failover_ops); in net_failover_create()
761 if (IS_ERR(failover)) { in net_failover_create()
762 err = PTR_ERR(failover); in net_failover_create()
766 return failover; in net_failover_create()
788 void net_failover_destroy(struct failover *failover) in net_failover_destroy() argument
794 if (!failover) in net_failover_destroy()
797 failover_dev = rcu_dereference(failover->failover_dev); in net_failover_destroy()
812 failover_unregister(failover); in net_failover_destroy()
|
| D | Kconfig | 656 This provides an automated failover mechanism via APIs to create
657 and destroy a failover master netdev and manages a primary and
658 standby slave netdevs that get registered via the generic failover
|
| D | virtio_net.c | 481 struct failover *failover; member
6597 vi->failover = net_failover_create(vi->dev); in virtnet_probe()
6598 if (IS_ERR(vi->failover)) { in virtnet_probe()
6599 err = PTR_ERR(vi->failover); in virtnet_probe()
6712 net_failover_destroy(vi->failover); in virtnet_probe()
6752 net_failover_destroy(vi->failover); in virtnet_remove()
|
| /linux-6.12.1/drivers/block/drbd/ |
| D | Kconfig | 37 For automatic failover you need a cluster manager (e.g. heartbeat).
|
| /linux-6.12.1/net/ |
| D | Kconfig | 503 tristate "Generic failover module"
505 The failover module provides a generic interface for paravirtual
506 drivers to register a netdev and a set of ops with a failover
510 failover netdev. This enables paravirtual drivers to use a
|
| /linux-6.12.1/Documentation/scsi/ |
| D | aacraid.rst | 155 - Performance tuning, card failover and bug mitigations.
|
| /linux-6.12.1/Documentation/admin-guide/device-mapper/ |
| D | switch.rst | 59 failover reasons.
|
| /linux-6.12.1/drivers/net/ethernet/marvell/ |
| D | Kconfig | 122 It does not support the link failover and network management
|
| /linux-6.12.1/net/netfilter/ipvs/ |
| D | Kconfig | 158 tristate "weighted failover scheduling"
160 The weighted failover scheduling algorithm directs network
|
| /linux-6.12.1/Documentation/admin-guide/ |
| D | xfs.rst | 209 where failover must not result in clients seeing
211 failover event.
|
| /linux-6.12.1/Documentation/networking/devlink/ |
| D | mlx5.rst | 90 failover between representors and stacked devices. By default metadata is
|
| /linux-6.12.1/drivers/infiniband/ulp/rtrs/ |
| D | README | 31 between client and server. Those are used for load balancing and failover.
|
| /linux-6.12.1/Documentation/translations/it_IT/process/ |
| D | changes.rst | 340 implementare un *failover*. Anche quando il sistema funziona bene, ``rmtab``
|
| /linux-6.12.1/Documentation/admin-guide/sysctl/ |
| D | vm.rst | 879 1 and 2 are for failover of clustering. Please select either
880 according to your policy of failover.
|
| /linux-6.12.1/drivers/net/ethernet/ibm/ |
| D | ibmvnic.c | 6638 static DEVICE_ATTR_WO(failover);
|