| /linux-6.12.1/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| D | boost.c | 33 u32 boost = 0; in nvbios_boostTe() local
37 boost = nvbios_rd32(bios, bit_P.offset + 0x30); in nvbios_boostTe()
39 if (boost) { in nvbios_boostTe()
40 *ver = nvbios_rd08(bios, boost + 0); in nvbios_boostTe()
43 *hdr = nvbios_rd08(bios, boost + 1); in nvbios_boostTe()
44 *cnt = nvbios_rd08(bios, boost + 5); in nvbios_boostTe()
45 *len = nvbios_rd08(bios, boost + 2); in nvbios_boostTe()
46 *snr = nvbios_rd08(bios, boost + 4); in nvbios_boostTe()
47 *ssz = nvbios_rd08(bios, boost + 3); in nvbios_boostTe()
48 return boost; in nvbios_boostTe()
|
| /linux-6.12.1/Documentation/devicetree/bindings/sound/ |
| D | cs35l34.txt | 13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
17 - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
28 - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
59 cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
60 cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
61 cirrus,boost-peak-milliamp = <3000>; /* 3A */
|
| D | cs35l36.txt | 13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
19 Configures the peak current by monitoring the current through the boost FET.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
25 Seeds the digital boost converter's inductor estimation block with the initial
36 - cirrus,boost-ctl-select : Boost converter control source selection.
37 Selects the source of the BST_CTL target VBST voltage for the boost
53 This enables the digital boost converter to operate in a low power
147 cirrus,boost-ind-nanohenry = <1000>;
148 cirrus,boost-ctl-millivolt = <10000>;
[all …]
|
| D | cs35l35.txt | 17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
37 - cirrus,external-boost : Boolean to specify the device is using an external
38 boost supply, note that sharing a boost from another cs35l35 would constitute
55 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
60 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
61 Configures the peak current by monitoring the current through the boost FET.
150 cirrus,boost-ctl-millivolt = <9000>;
155 cirrus,shared-boost;
|
| D | cs35l33.txt | 21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
22 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
34 - cirrus,boost-ipk : The maximum current allowed for the boost converter.
109 cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
110 cirrus,boost-ipk = <0xE0>; /* 3600mA */
|
| D | cs35l32.txt | 18 - cirrus,boost-manager : Boost voltage control.
59 cirrus,boost-manager = <0x03>;
|
| /linux-6.12.1/Documentation/usb/ |
| D | iuu_phoenix.rst | 40 boost:
41 overclock boost percent 100 to 500 (int)
57 - boost provide a way to overclock the reader ( my favorite :-) )
60 modprobe boost=195
84 use this settings to deduce de boost but is that feature
|
| /linux-6.12.1/Documentation/iio/ |
| D | ad7380.rst | 61 Oversampling and resolution boost
70 exceed the default resolution. To accommodate the performance boost achievable,
72 resolution boost feature can only be enabled when oversampling is enabled and
73 oversampling is not as useful without the resolution boost, the driver
74 automatically enables the resolution boost if and only if oversampling is
77 Since the resolution boost feature causes 16-bit chips to now have 18-bit data
|
| /linux-6.12.1/drivers/usb/serial/ |
| D | iuu_phoenix.c | 38 static int boost = 100; variable
61 u32 boost; member
919 baud * priv->boost / 100, in iuu_set_termios()
990 if (boost < 100) in iuu_open()
991 boost = 100; in iuu_open()
992 priv->boost = boost; in iuu_open()
996 iuu_clk(port, IUU_CLK_3680000 * boost / 100); in iuu_open()
998 iuu_uart_baud(port, baud * boost / 100, &actual, in iuu_open()
1002 iuu_clk(port, IUU_CLK_6000000 * boost / 100); in iuu_open()
1006 iuu_uart_baud(port, 16457 * boost / 100, &actual, in iuu_open()
[all …]
|
| /linux-6.12.1/kernel/sched/ |
| D | cpufreq_schedutil.c | 198 static void sugov_get_util(struct sugov_cpu *sg_cpu, unsigned long boost) in sugov_get_util() argument
205 util = max(util, boost); in sugov_get_util()
375 unsigned long boost; in sugov_update_single_common() local
385 boost = sugov_iowait_apply(sg_cpu, time, max_cap); in sugov_update_single_common()
386 sugov_get_util(sg_cpu, boost); in sugov_update_single_common()
474 unsigned long boost; in sugov_next_freq_shared() local
476 boost = sugov_iowait_apply(j_sg_cpu, time, max_cap); in sugov_next_freq_shared()
477 sugov_get_util(j_sg_cpu, boost); in sugov_next_freq_shared()
|
| /linux-6.12.1/arch/arm64/boot/dts/qcom/ |
| D | sm8250-sony-xperia-edo.dtsi | 483 cirrus,boost-peak-milliamp = <4000>;
484 cirrus,boost-ind-nanohenry = <1000>;
485 cirrus,boost-cap-microfarad = <15>;
498 cirrus,boost-peak-milliamp = <4000>;
499 cirrus,boost-ind-nanohenry = <1000>;
500 cirrus,boost-cap-microfarad = <15>;
|
| D | sm8450-sony-xperia-nagara.dtsi | 575 cirrus,boost-peak-milliamp = <4000>;
576 cirrus,boost-ind-nanohenry = <1000>;
577 cirrus,boost-cap-microfarad = <15>;
590 cirrus,boost-peak-milliamp = <4000>;
591 cirrus,boost-ind-nanohenry = <1000>;
592 cirrus,boost-cap-microfarad = <15>;
|
| D | sm8350-sony-xperia-sagami.dtsi | 500 cirrus,boost-peak-milliamp = <4000>;
501 cirrus,boost-ind-nanohenry = <1000>;
502 cirrus,boost-cap-microfarad = <15>;
515 cirrus,boost-peak-milliamp = <4000>;
516 cirrus,boost-ind-nanohenry = <1000>;
517 cirrus,boost-cap-microfarad = <15>;
|
| /linux-6.12.1/Documentation/translations/zh_CN/cpu-freq/ |
| D | cpu-drivers.rst | 92 .boost_enabled - 如果设置，则启用提升(boost)频率。
94 .set_boost - 一个指向per-policy函数的指针，该函数用来开启/关闭提升(boost)频率功能。
|
| /linux-6.12.1/Documentation/translations/zh_TW/cpu-freq/ |
| D | cpu-drivers.rst | 92 .boost_enabled - 如果設置，則啓用提升(boost)頻率。
94 .set_boost - 一個指向per-policy函數的指針，該函數用來開啓/關閉提升(boost)頻率功能。
|
| /linux-6.12.1/sound/pcmcia/vx/ |
| D | vxpocket.h | 37 void vx_set_mic_boost(struct vx_core *chip, int boost);
|
| /linux-6.12.1/Documentation/ABI/testing/ |
| D | sysfs-platform-asus-wmi | 46 Fan boost mode:
98 Enable an LCD response-time boost to reduce or remove ghosting:
187 Set the dynamic boost limit of the Nvidia dGPU:
|
| /linux-6.12.1/Documentation/admin-guide/pm/ |
| D | amd-pstate.rst | 252 table, so we need to expose it to sysfs. If boost is not active, but
297 ``boost``
298 The `boost` sysfs attribute provides control over the CPU core
299 performance boost, allowing users to manage the maximum frequency limitation
300 of the CPU. This attribute can be used to enable or disable the boost feature
303 When the boost feature is enabled, the CPU can dynamically increase its frequency
305 On the other hand, disabling the boost feature restricts the CPU to operate at the
309 To manipulate the `boost` attribute, users can write a value of `0` to disable the
310 boost or `1` to enable it, for the respective CPU using the sysfs path
311 `/sys/devices/system/cpu/cpuX/cpufreq/boost`, where `X` represents the CPU number.
[all …]
|
| D | cpufreq.rst | 613 term "frequency boost" is used here for brevity to refer to all of those
616 The frequency boost mechanism may be either hardware-based or software-based.
623 The ``boost`` File in ``sysfs``
627 the "boost" setting for the whole system. It is not present if the underlying
628 scaling driver does not support the frequency boost mechanism (or supports it,
632 If the value in this file is 1, the frequency boost mechanism is enabled. This
637 permission to use the frequency boost mechanism (which still may never be used
640 If the value in this file is 0, the frequency boost mechanism is disabled and
648 The frequency boost mechanism is generally intended to help to achieve optimum
653 For this reason, many systems make it possible to disable the frequency boost
[all …]
|
| /linux-6.12.1/drivers/power/supply/ |
| D | bq2415x_charger.c | 726 int boost = 0; in bq2415x_set_mode() local
729 boost = 1; in bq2415x_set_mode()
736 if (!boost) in bq2415x_set_mode()
770 else if (boost) in bq2415x_set_mode()
891 int boost; in bq2415x_timer_work() local
907 boost = bq2415x_exec_command(bq, BQ2415X_BOOST_MODE_STATUS); in bq2415x_timer_work()
908 if (boost < 0) { in bq2415x_timer_work()
919 if (boost) { in bq2415x_timer_work()
|
| /linux-6.12.1/Documentation/devicetree/bindings/phy/ |
| D | apm-xgene-phy.txt | 27 - apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit)
|
| /linux-6.12.1/Documentation/devicetree/bindings/leds/backlight/ |
| D | tps65217-backlight.txt | 3 The TPS65217 chip contains a boost converter and current sinks which can be
|
| /linux-6.12.1/arch/arm/boot/dts/qcom/ |
| D | qcom-msm8974-sony-xperia-rhine.dtsi | 69 vreg_boost: vreg-boost {
72 regulator-name = "vreg-boost";
212 qcom,current-boost-limit = <805>;
|
| /linux-6.12.1/Documentation/sound/hd-audio/ |
| D | realtek-pc-beep.rst | 31 selected, the 1Ah boost control has no effect.
58 +--DIV--+--!DIV--+ {1Ah boost control}
119 1Ah boost control. (If you've seen instructions online to fix XPS 13 headphone
|
| /linux-6.12.1/arch/arm64/boot/dts/exynos/ |
| D | exynos7-espresso.dts | 45 usb3drd_boost_5v: regulator-usb3drd-boost {
402 usb3drd_boost_en: usb3drd-boost-en-pins {
421 vbus-boost-supply = <&usb3drd_boost_5v>;
|