| /linux-6.12.1/drivers/tty/ |
| D | amiserial.c | 76 int baud_base; member
570 int quot = 0, baud_base, baud; in change_speed() local
597 baud_base = info->baud_base; in change_speed()
603 quot = (2*baud_base / 269); in change_speed()
605 quot = baud_base / baud; in change_speed()
621 quot = (2*baud_base / 269); in change_speed()
623 quot = baud_base / baud; in change_speed()
628 quot = baud_base / 9600; in change_speed()
630 info->timeout = (XMIT_FIFO_SIZE*HZ*bits*quot) / baud_base; in change_speed()
907 ss->baud_base = state->baud_base; in get_serial_info()
[all …]
|
| D | mxser.c | 983 ss->baud_base = MXSER_BAUD_BASE; in mxser_get_serial_info()
1020 if ((ss->baud_base != MXSER_BAUD_BASE) || in mxser_set_serial_info()
1039 (ss->baud_base != MXSER_BAUD_BASE || in mxser_set_serial_info()
1046 baud = ss->baud_base / ss->custom_divisor; in mxser_set_serial_info()
|
| /linux-6.12.1/drivers/ssb/ |
| D | driver_chipcommon.c | 608 u32 baud_base, div; in ssb_chipco_serial_init() local
617 baud_base = ssb_calc_clock_rate(plltype, in ssb_chipco_serial_init()
624 baud_base = 25000000; in ssb_chipco_serial_init()
631 baud_base = ssb_chipco_alp_clock(cc); in ssb_chipco_serial_init()
651 baud_base = ssb_clockspeed(bus); in ssb_chipco_serial_init()
656 baud_base = 88000000; in ssb_chipco_serial_init()
666 baud_base /= div; in ssb_chipco_serial_init()
669 baud_base = 1843200; in ssb_chipco_serial_init()
691 ports[i].baud_base = baud_base; in ssb_chipco_serial_init()
|
| D | driver_extif.c | 76 ports[i].baud_base = 13500000; in ssb_extif_serial_init()
|
| /linux-6.12.1/arch/mips/bcm47xx/ |
| D | serial.c | 44 p->uartclk = ssb_port->baud_base; in uart8250_init_ssb()
70 p->uartclk = bcma_port->baud_base; in uart8250_init_bcma()
|
| /linux-6.12.1/drivers/bcma/ |
| D | driver_chipcommon.c | 380 u32 baud_base; in bcma_chipco_serial_init() local
386 baud_base = bcma_chipco_get_alp_clock(cc); in bcma_chipco_serial_init()
417 ports[i].baud_base = baud_base; in bcma_chipco_serial_init()
|
| /linux-6.12.1/drivers/accessibility/speakup/ |
| D | serialio.h | 17 unsigned int baud_base; member
|
| D | serialio.c | 63 quot = ser->baud_base / baud; in spk_serial_init()
|
| /linux-6.12.1/include/linux/ssb/ |
| D | ssb_driver_mips.h | 13 unsigned int baud_base; member
|
| /linux-6.12.1/drivers/usb/serial/ |
| D | f81232.c | 121 speed_t baud_base; member
516 priv->baud_base = baudrate_table[idx]; in f81232_set_baudrate()
517 divisor = calc_baud_divisor(baudrate, priv->baud_base); in f81232_set_baudrate()
798 ss->baud_base = priv->baud_base; in f81232_get_serial()
|
| D | f81534.c | 164 u32 baud_base; member
584 port_priv->baud_base = baudrate_table[idx]; in f81534_set_port_config()
618 divisor = f81534_calc_baud_divisor(baudrate, port_priv->baud_base); in f81534_set_port_config()
1140 ss->baud_base = port_priv->baud_base; in f81534_get_serial_info()
|
| D | ftdi_sio.c | 71 int baud_base; /* baud base clock for divisor setting */ member
1271 baud = priv->baud_base / priv->custom_divisor; in get_ftdi_divisor()
1447 ss->baud_base = priv->baud_base; in get_serial_info()
1513 priv->baud_base = 120000000 / 2; in ftdi_determine_type()
1519 priv->baud_base = 48000000 / 2; in ftdi_determine_type()
1533 priv->baud_base = 48000000 / 2; in ftdi_determine_type()
1538 priv->baud_base = 48000000 / 2; in ftdi_determine_type()
1542 priv->baud_base = 48000000 / 2; in ftdi_determine_type()
1556 priv->baud_base = 48000000 / 2; in ftdi_determine_type()
1582 priv->baud_base = 12000000 / 16; in ftdi_determine_type()
|
| D | iuu_phoenix.c | 786 static int iuu_uart_baud(struct usb_serial_port *port, u32 baud_base, in iuu_uart_baud() argument
797 dev_dbg(&port->dev, "%s - enter baud_base=%d\n", __func__, baud_base); in iuu_uart_baud()
803 baud = baud_base; in iuu_uart_baud()
|
| /linux-6.12.1/include/uapi/linux/ |
| D | serial.h | 28 int baud_base; member
|
| /linux-6.12.1/drivers/tty/serial/ |
| D | ar933x_uart.c | 556 if (ser->baud_base < up->min_baud || in ar933x_uart_verify_port()
557 ser->baud_base > up->max_baud) in ar933x_uart_verify_port()
|
| D | 21285.c | 347 if (ser->baud_base != port->uartclk / 16) in serial21285_verify_port()
|
| D | serial_core.c | 815 retinfo->baud_base = uport->uartclk / 16; in uart_get_info()
887 unsigned int uartclk = new_info->baud_base * 16; in uart_set_info()
897 (new_info->baud_base != uport->uartclk / 16) || in uart_set_info()
923 (new_info->baud_base < 9600)) in uart_set_info()
1014 uport->uartclk = new_info->baud_base * 16; in uart_set_info()
2907 return sprintf(buf, "%d\n", tmp.baud_base * 16); in uartclk_show()
|
| D | apbuart.c | 292 if (ser->baud_base < 9600) in apbuart_verify_port()
|
| D | amba-pl010.c | 504 if (ser->baud_base < 9600) in pl010_verify_port()
|
| /linux-6.12.1/drivers/tty/serial/8250/ |
| D | 8250.h | 58 unsigned int baud_base; member
|
| D | 8250_platform.c | 89 port->uartclk = old_serial_port[i].baud_base * 16; in __serial8250_isa_init_ports()
|
| /linux-6.12.1/Documentation/ABI/testing/ |
| D | sysfs-tty | 27 uartclk = 16 * baud_base
|
| /linux-6.12.1/Documentation/driver-api/tty/ |
| D | moxa-smartio.rst | 180 baud_base This option sets the base baud rate.
|
| /linux-6.12.1/drivers/tty/ipwireless/ |
| D | tty.c | 262 ss->baud_base = 115200; in ipwireless_get_serial_info()
|
| /linux-6.12.1/include/linux/bcma/ |
| D | bcma_driver_chipcommon.h | 618 unsigned int baud_base; member
|