Searched refs:STATUS_REG (Results 1 – 12 of 12) sorted by relevance
| /linux-6.12.1/drivers/char/hw_random/ |
| D | xiphera-trng.c | 14 #define STATUS_REG 0x00000004 macro
42 if (readl(trng->mem + STATUS_REG) == TRNG_NEW_RAND_AVAILABLE) { in xiphera_trng_read()
81 if (readl(trng->mem + STATUS_REG) != TRNG_ACK_RESET) { in xiphera_trng_probe()
87 if (readl(trng->mem + STATUS_REG) != TRNG_ACK_RESET) { in xiphera_trng_probe()
102 if (readl(trng->mem + STATUS_REG) != TRNG_SUCCESSFUL_STARTUP) { in xiphera_trng_probe()
104 if (readl(trng->mem + STATUS_REG) == TRNG_FAILED_STARTUP) { in xiphera_trng_probe()
|
| /linux-6.12.1/drivers/scsi/ |
| D | NCR5380.c | 297 status = NCR5380_read(STATUS_REG); in NCR5380_print()
347 status = NCR5380_read(STATUS_REG); in NCR5380_print_phase()
444 NCR5380_read(STATUS_REG); in NCR5380_init()
473 for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) { in NCR5380_maybe_reset_bus()
480 STATUS_REG, SR_BSY, 0, 5 * HZ); in NCR5380_maybe_reset_bus()
808 if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) { in NCR5380_dma_complete()
875 unsigned char sr = NCR5380_read(STATUS_REG); in NCR5380_intr()
1134 err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_BSY, SR_BSY, in NCR5380_select()
1137 if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) { in NCR5380_select()
1180 err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ); in NCR5380_select()
[all …]
|
| D | NCR5380.h | 111 #define STATUS_REG 4 /* ro */ macro
|
| D | mac_scsi.c | 459 (STATUS_REG << 4))) { in mac_scsi_probe()
|
| D | g_NCR5380.c | 129 PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK)); in g_NCR5380_trigger_irq()
|
| /linux-6.12.1/drivers/rtc/ |
| D | rtc-spear.c | 28 #define STATUS_REG 0x14 macro
91 val = readl(config->ioaddr + STATUS_REG); in spear_rtc_clear_interrupt()
93 writel(val, config->ioaddr + STATUS_REG); in spear_rtc_clear_interrupt()
126 if ((readl(config->ioaddr + STATUS_REG)) & STATUS_FAIL) in is_write_complete()
141 status = readl(config->ioaddr + STATUS_REG); in rtc_wait_not_busy()
157 irq_data = readl(config->ioaddr + STATUS_REG); in spear_rtc_irq()
|
| /linux-6.12.1/drivers/input/keyboard/ |
| D | spear-keyboard.c | 30 #define STATUS_REG 0x0C macro
76 sts = readl_relaxed(kbd->io_base + STATUS_REG); in spear_kbd_interrupt()
97 writel_relaxed(0, kbd->io_base + STATUS_REG); in spear_kbd_interrupt()
122 writel_relaxed(1, kbd->io_base + STATUS_REG); in spear_kbd_open()
|
| /linux-6.12.1/drivers/media/i2c/ |
| D | ml86v7667.c | 34 #define STATUS_REG 0x2C /* STATUS Register */ macro
164 status = i2c_smbus_read_byte_data(client, STATUS_REG); in ml86v7667_querystd()
181 status_reg = i2c_smbus_read_byte_data(client, STATUS_REG); in ml86v7667_g_input_status()
349 val = i2c_smbus_read_byte_data(client, STATUS_REG); in ml86v7667_init()
|
| /linux-6.12.1/drivers/comedi/drivers/ |
| D | ni_at_a2150.c | 71 #define STATUS_REG 0x12 /* read only */ macro
148 status = inw(dev->iobase + STATUS_REG); in a2150_interrupt()
570 status = inw(dev->iobase + STATUS_REG); in a2150_ai_eoc()
676 int id = ID_BITS(inw(dev->iobase + STATUS_REG)); in a2150_probe()
747 if ((DCAL_BIT & inw(dev->iobase + STATUS_REG)) == 0) in a2150_attach()
|
| /linux-6.12.1/drivers/misc/lis3lv02d/ |
| D | lis3lv02d.h | 39 STATUS_REG = 0x27, enumerator
|
| /linux-6.12.1/drivers/mtd/nand/raw/ |
| D | renesas-nand-controller.c | 54 #define STATUS_REG 0x8 macro
362 ret = readl_poll_timeout(rnandc->regs + STATUS_REG, status, in rnandc_wait_end_of_op()
|
| /linux-6.12.1/drivers/net/ethernet/qlogic/ |
| D | qla3xxx.h | 698 STATUS_REG = 1, enumerator
|