Searched refs:RS485 (Results 1 – 25 of 34) sorted by relevance
12
2 RS485 Serial Communications21 half-duplex hardware like an RS485 transceiver or any RS232-connected32 The Linux kernel provides the struct serial_rs485 to handle RS48533 communications. This data structure is used to set and configure RS48536 The device tree can also provide RS485 boot time parameters41 Any driver for devices capable of working both as RS232 and RS485 should48 what RS485 features the driver supports for the ``struct uart_port``.58 From user-level, RS485 configuration can be get/set using the previous59 ioctls. For instance, to set RS485 you can use the following code::63 /* Include definition for RS485 ioctls: TIOCGRS485 and TIOCSRS485 */[all …]
5 * GW72xx RS422 (RS485 full duplex):9 * - UART4_TX is DE for RS485 transmitter
5 * GW73xx RS485 HD:9 * - UART4_TX is DE for RS485 transmitter
5 * GW72xx RS485 HD:9 * - UART4_TX is DE for RS485 transmitter
5 * GW73xx RS422 (RS485 full duplex):9 * - UART4_TX is DE for RS485 transmitter
6 * Tauri-L RS232 + RS485:39 /* UART4 - RS485 */
136 /* Verdin UART_1, connector X50 through RS485 transceiver */
228 /* Verdin UART_1, connector X50 through RS485 transceiver */
1018 MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x40000041 /* RS485# */1043 MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x40000110 /* RS485# */1061 MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x40000041 /* RS485# */
579 /* off-board RS232/RS485/RS422 */641 MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x40000041 /* RS485# */
263 MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /* RS485 */
627 /* RS232/RS485/RS422 selectable */891 MX8MN_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x40000110 /* RS485 */
300 MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /* RS485 */
664 /* RS232/RS485/RS422 selectable */956 MX8MM_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x40000110 /* RS485 */
50 #define RS485 0xF0 macro229 sio_write_reg(pdata, RS485, config); in fintek_8250_rs485_config()301 reg = RS485; in fintek_8250_set_termios()
23 serial5 = &uart5; /* RS485 */187 &uart5 { /* RS485 */
294 label = "RS485-1";303 &usart3 { /* RS485 or RS232 */304 label = "RS485-2";
144 &uart8 { /* RS485 */
45 Indicates the presence of the RS485 option. If it is present,
622 /* RS485 RX Enable: pull up */624 /* RS485 DEN: pull down */626 /* RS485/!RS232 Select: pull down (rs232) */
94 /* Use UART as RS485 */
85 * On DRC02 this UART is used as RS485 interface and RS485_TX_En is
169 /* Verdin UART_1, connector X50 through RS485 transceiver. */
196 /* RS485 */
188 /* RS485 - UART1 */