| /linux-6.12.1/drivers/gpu/drm/amd/amdgpu/ |
| D | nbif_v6_3_1.c | 350 def = data = RREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL); in nbif_v6_3_1_program_aspm()
355 WREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL, data); in nbif_v6_3_1_program_aspm()
357 def = data = RREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL7); in nbif_v6_3_1_program_aspm()
360 WREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL7, data); in nbif_v6_3_1_program_aspm()
362 def = data = RREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL3); in nbif_v6_3_1_program_aspm()
365 WREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL3, data); in nbif_v6_3_1_program_aspm()
399 def = data = RREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL4); in nbif_v6_3_1_program_aspm()
402 WREG32_SOC15(PCIE, 0, regPCIE_LC_CNTL4, data); in nbif_v6_3_1_program_aspm()
404 def = data = RREG32_SOC15(PCIE, 0, regPCIE_LC_RXRECOVER_RXSTANDBY_CNTL); in nbif_v6_3_1_program_aspm()
407 WREG32_SOC15(PCIE, 0, regPCIE_LC_RXRECOVER_RXSTANDBY_CNTL, data); in nbif_v6_3_1_program_aspm()
[all …]
|
| /linux-6.12.1/Documentation/admin-guide/perf/ |
| D | nvidia-pmu.rst | 12 * PCIE
32 strongly-ordered (SO) PCIE write traffic to local/remote memory. Please see
63 PCIE device of the remote SoC.
122 The CNVLink PMU monitors traffic from GPU and PCIE device on remote sockets
123 to local memory. For PCIE traffic, this PMU captures read and relaxed ordered
139 traffic from remote GPU and PCIE devices.
160 PCIE PMU
163 The PCIE PMU monitors all read/write traffic from PCIE root ports to
201 * : PCIE : * * : PCIE : *
233 | Local | PCIE |NVLink-C2C0|NVLink-C2C1| SCF | SCF PMU | CNVLink |
[all …]
|
| /linux-6.12.1/drivers/net/wireless/broadcom/brcm80211/brcmfmac/ |
| D | pcie.c | 698 brcmf_dbg(PCIE, "config offset 0x%04x, value 0x%04x\n", in brcmf_pcie_reset_device()
769 brcmf_dbg(PCIE, "MB transaction is already pending 0x%04x\n", in brcmf_pcie_send_mb_data()
808 brcmf_dbg(PCIE, "D2H_MB_DATA: 0x%04x\n", dtoh_mb_data); in brcmf_pcie_handle_mb_data()
810 brcmf_dbg(PCIE, "D2H_MB_DATA: DEEP SLEEP REQ\n"); in brcmf_pcie_handle_mb_data()
812 brcmf_dbg(PCIE, "D2H_MB_DATA: sent DEEP SLEEP ACK\n"); in brcmf_pcie_handle_mb_data()
815 brcmf_dbg(PCIE, "D2H_MB_DATA: DEEP SLEEP EXIT\n"); in brcmf_pcie_handle_mb_data()
817 brcmf_dbg(PCIE, "D2H_MB_DATA: D3 ACK\n"); in brcmf_pcie_handle_mb_data()
822 brcmf_dbg(PCIE, "D2H_MB_DATA: FW HALT\n"); in brcmf_pcie_handle_mb_data()
927 brcmf_dbg(PCIE, "Enter\n"); in brcmf_pcie_quick_check_isr()
941 brcmf_dbg(PCIE, "Enter %x\n", status); in brcmf_pcie_isr_thread()
[all …]
|
| D | Kconfig | 41 bool "PCIE bus interface support for FullMAC driver"
47 This option enables the PCIE bus interface support for Broadcom
49 use the driver for an PCIE wireless card.
|
| /linux-6.12.1/drivers/phy/amlogic/ |
| D | Kconfig | 64 tristate "Meson G12A USB3+PCIE Combo PHY driver"
70 Enable this to support the Meson USB3 + PCIE Combo PHY found
75 tristate "Meson AXG PCIE PHY driver"
81 Enable this to support the Meson MIPI + PCIE PHY found
86 tristate "Meson AXG MIPI + PCIE analog PHY driver"
93 Enable this to support the Meson MIPI + PCIE analog PHY
|
| /linux-6.12.1/drivers/infiniband/hw/hfi1/ |
| D | chip_registers.h | 20 #define PCIE 0 macro
584 #define PCI_CFG_MSIX0 (PCIE + 0x0000000000B0)
585 #define PCI_CFG_REG1 (PCIE + 0x000000000004)
586 #define PCI_CFG_REG11 (PCIE + 0x00000000002C)
587 #define PCIE_CFG_SPCIE1 (PCIE + 0x00000000014C)
588 #define PCIE_CFG_SPCIE2 (PCIE + 0x000000000150)
589 #define PCIE_CFG_TPH2 (PCIE + 0x000000000180)
1269 #define PCIE_CFG_REG_PL2 (PCIE + 0x000000000708)
1270 #define PCIE_CFG_REG_PL3 (PCIE + 0x00000000070C)
1273 #define PCIE_CFG_REG_PL102 (PCIE + 0x000000000898)
[all …]
|
| /linux-6.12.1/drivers/net/ethernet/huawei/hinic/ |
| D | Kconfig | 7 tristate "Huawei Intelligent PCIE Network Interface Card"
11 This driver supports HiNIC PCIE Ethernet cards.
|
| /linux-6.12.1/drivers/phy/st/ |
| D | phy-spear1310-miphy.c | 98 PCIE, enumerator
156 if (priv->mode == PCIE) in spear1310_miphy_init()
167 if (priv->mode == PCIE) in spear1310_miphy_exit()
197 if (priv->mode != SATA && priv->mode != PCIE) { in spear1310_miphy_xlate()
|
| D | phy-spear1340-miphy.c | 77 PCIE, enumerator
164 else if (priv->mode == PCIE) in spear1340_miphy_init()
177 else if (priv->mode == PCIE) in spear1340_miphy_exit()
234 if (priv->mode != SATA && priv->mode != PCIE) { in spear1340_miphy_xlate()
|
| D | Kconfig | 10 Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
|
| /linux-6.12.1/drivers/soc/loongson/ |
| D | Kconfig | 11 The global utilities block controls PCIE device enabling, alternate
13 and PCIE, configuration of memory controller, rtc controller, lio
|
| /linux-6.12.1/Documentation/translations/zh_CN/mm/ |
| D | hmm.rst | 67 如果我们只考虑 PCIE 总线，那么设备可以访问主内存（通常通过 IOMMU）并与 CPU 缓存一
72 另一个严重的因素是带宽有限（约 32GBytes/s，PCIE 4.0 和 16 通道）。这比最快的 GPU
76 一些平台正在开发新的 I/O 总线或对 PCIE 的添加/修改以解决其中一些限制
|
| /linux-6.12.1/drivers/phy/freescale/ |
| D | Kconfig | 31 tristate "Freescale i.MX8M PCIE PHY"
35 Enable this to add support for the PCIE PHY as found on
|
| /linux-6.12.1/arch/arm/boot/dts/nxp/imx/ |
| D | imx6qdl-mba6.dtsi | 94 /* PCIE.PWR_EN */
494 MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x001b0f0 /* #PCIE.WAKE */
495 MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x001b0f0 /* #PCIE.RST */
496 MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x001b0f0 /* #PCIE.DIS */
524 MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x00130f0 /* PCIE.PWR_EN */
|
| D | imx6q-gw5400-a.dts | 452 MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 /* PCIE IRQ */
453 MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PCIE RST */
|
| /linux-6.12.1/arch/arm/boot/dts/aspeed/ |
| D | aspeed-bmc-tyan-s7106.dts | 360 * - 0,0: PCIE slot 1, SMB #1
361 * - 0,1: PCIE slot 1, SMB #2
362 * - 1,0: PCIE slot 2, SMB #1
363 * - 1,1: PCIE slot 2, SMB #2
|
| /linux-6.12.1/Documentation/devicetree/bindings/phy/ |
| D | rockchip-pcie-phy.txt | 1 Rockchip PCIE PHY
|
| /linux-6.12.1/drivers/perf/hisilicon/ |
| D | Kconfig | 10 tristate "HiSilicon PCIE PERF PMU"
|
| /linux-6.12.1/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-zcu102-revA.dts | 250 output-low; /* PCIE = 0, DP = 1 */
256 output-high; /* PCIE = 0, DP = 1 */
262 output-high; /* PCIE = 0, USB0 = 1 */
268 output-high; /* PCIE = 0, SATA = 1 */
556 /* refclk4 for PS-GT, used for PCIE slot */
561 /* refclk5 for PS-GT, used for PCIE */
|
| /linux-6.12.1/drivers/net/can/sja1000/ |
| D | Kconfig | 25 tristate "Fintek F81601 PCIE to 2 CAN Controller"
28 This driver adds support for Fintek F81601 PCIE to 2 CAN
|
| /linux-6.12.1/drivers/net/wireless/marvell/mwifiex/ |
| D | Kconfig | 26 tristate "Marvell WiFi-Ex Driver for PCIE 8766/8897/8997"
|
| /linux-6.12.1/drivers/phy/starfive/ |
| D | Kconfig | 29 tristate "Starfive JH7110 PCIE 2.0/USB 3.0 PHY support"
|
| /linux-6.12.1/arch/arm64/boot/dts/renesas/ |
| D | salvator-xs.dtsi | 37 line-name = "PCIE/SATA switch";
|
| /linux-6.12.1/drivers/net/wireless/ath/ath11k/ |
| D | Kconfig | 29 This module adds support for PCIE bus
|
| /linux-6.12.1/drivers/pinctrl/tegra/ |
| D | pinctrl-tegra30.c | 2401 …PINGROUP(pex_l2_rst_n_pcc6, PCIE, HDA, RSVD3, RSVD4, 0x33d8, N, …
2402 …PINGROUP(pex_l2_clkreq_n_pcc7, PCIE, HDA, RSVD3, RSVD4, 0x33dc, N, …
2403 …PINGROUP(pex_l0_prsnt_n_pdd0, PCIE, HDA, RSVD3, RSVD4, 0x33b8, N, …
2404 …PINGROUP(pex_l0_rst_n_pdd1, PCIE, HDA, RSVD3, RSVD4, 0x33bc, N, …
2405 …PINGROUP(pex_l0_clkreq_n_pdd2, PCIE, HDA, RSVD3, RSVD4, 0x33c0, N, …
2406 …PINGROUP(pex_wake_n_pdd3, PCIE, HDA, RSVD3, RSVD4, 0x33c4, N, …
2407 …PINGROUP(pex_l1_prsnt_n_pdd4, PCIE, HDA, RSVD3, RSVD4, 0x33c8, N, …
2408 …PINGROUP(pex_l1_rst_n_pdd5, PCIE, HDA, RSVD3, RSVD4, 0x33cc, N, …
2409 …PINGROUP(pex_l1_clkreq_n_pdd6, PCIE, HDA, RSVD3, RSVD4, 0x33d0, N, …
2410 …PINGROUP(pex_l2_prsnt_n_pdd7, PCIE, HDA, RSVD3, RSVD4, 0x33d4, N, …
|