Searched refs:Opcode (Results 1 – 11 of 11) sorted by relevance
86 [ 0.186630] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905c88:If] execution.87 [ 0.186820] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905cc0:LEqual] execution.88 …[ 0.187010] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905a20:-NamePath-] executi…89 …[ 0.187214] exdebug-0398 ex_trace_point : Opcode End [0xf5905a20:-NamePath-] execution.90 [ 0.187407] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905f60:One] execution.91 [ 0.187594] exdebug-0398 ex_trace_point : Opcode End [0xf5905f60:One] execution.92 [ 0.187789] exdebug-0398 ex_trace_point : Opcode End [0xf5905cc0:LEqual] execution.93 [ 0.187980] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905cc0:Return] execution.94 [ 0.188146] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905f60:One] execution.95 [ 0.188334] exdebug-0398 ex_trace_point : Opcode End [0xf5905f60:One] execution.[all …]
181 2R Opcode + Rj + Rd182 3R Opcode + Rk + Rj + Rd183 4R Opcode + Ra + Rk + Rj + Rd184 2RI8 Opcode + I8 + Rj + Rd185 2RI12 Opcode + I12 + Rj + Rd186 2RI14 Opcode + I14 + Rj + Rd187 2RI16 Opcode + I16 + Rj + Rd188 1RI21 Opcode + I21L + Rj + I21H189 I26 Opcode + I26L + I26H192 Opcode是指令操作碼，Rj和Rk是源操作數（寄存器），Rd是目標操作數（寄存器），Ra是
181 2R Opcode + Rj + Rd182 3R Opcode + Rk + Rj + Rd183 4R Opcode + Ra + Rk + Rj + Rd184 2RI8 Opcode + I8 + Rj + Rd185 2RI12 Opcode + I12 + Rj + Rd186 2RI14 Opcode + I14 + Rj + Rd187 2RI16 Opcode + I16 + Rj + Rd188 1RI21 Opcode + I21L + Rj + I21H189 I26 Opcode + I26L + I26H192 Opcode是指令操作码，Rj和Rk是源操作数（寄存器），Rd是目标操作数（寄存器），Ra是
212 2R Opcode + Rj + Rd213 3R Opcode + Rk + Rj + Rd214 4R Opcode + Ra + Rk + Rj + Rd215 2RI8 Opcode + I8 + Rj + Rd216 2RI12 Opcode + I12 + Rj + Rd217 2RI14 Opcode + I14 + Rj + Rd218 2RI16 Opcode + I16 + Rj + Rd219 1RI21 Opcode + I21L + Rj + I21H220 I26 Opcode + I26L + I26H
36 com.cmd.hdr.Opcode = CMD_I2C_READ; in ngene_command_i2c_read()64 com.cmd.hdr.Opcode = CMD_I2C_WRITE; in ngene_command_i2c_write()
262 if (com->cmd.hdr.Opcode == CMD_FWLOAD_PREPARE) { in ngene_command_mutex()271 } else if (com->cmd.hdr.Opcode == CMD_FWLOAD_FINISH) { in ngene_command_mutex()305 com->cmd.hdr.Opcode, dev->prev_cmd); in ngene_command_mutex()309 if (com->cmd.hdr.Opcode == CMD_FWLOAD_FINISH) in ngene_command_mutex()312 dev->prev_cmd = com->cmd.hdr.Opcode; in ngene_command_mutex()340 com.cmd.hdr.Opcode = CMD_FWLOAD_PREPARE; in ngene_command_load_firmware()356 com.cmd.hdr.Opcode = CMD_FWLOAD_FINISH; in ngene_command_load_firmware()371 com.cmd.hdr.Opcode = CMD_CONFIGURE_BUFFER; in ngene_command_config_buf()386 com.cmd.hdr.Opcode = CMD_CONFIGURE_FREE_BUFFER; in ngene_command_config_free_buf()402 com.cmd.hdr.Opcode = CMD_SET_GPIO_PIN; in ngene_command_gpio_set()[all …]
250 u8 Opcode; member
38 done via the instruction **HVCS** that expects the Opcode for hcall is set in *r3*
255 - Opcode, which must be one of the documented allowable commands
1 # x86 Opcode Maps7 #<Opcode maps>