1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (C) 2022 Schneider Electric 4 * 5 * Clément Léger <clement.leger@bootlin.com> 6 */ 7 8 #include <linux/clk.h> 9 #include <linux/device.h> 10 #include <linux/mdio.h> 11 #include <linux/of.h> 12 #include <linux/of_platform.h> 13 #include <linux/pcs-rzn1-miic.h> 14 #include <linux/phylink.h> 15 #include <linux/platform_device.h> 16 #include <linux/pm_runtime.h> 17 #include <dt-bindings/net/pcs-rzn1-miic.h> 18 19 #define MIIC_PRCMD 0x0 20 #define MIIC_ESID_CODE 0x4 21 22 #define MIIC_MODCTRL 0x20 23 #define MIIC_MODCTRL_SW_MODE GENMASK(4, 0) 24 25 #define MIIC_CONVCTRL(port) (0x100 + (port) * 4) 26 27 #define MIIC_CONVCTRL_CONV_SPEED GENMASK(1, 0) 28 #define CONV_MODE_10MBPS 0 29 #define CONV_MODE_100MBPS 1 30 #define CONV_MODE_1000MBPS 2 31 32 #define MIIC_CONVCTRL_CONV_MODE GENMASK(3, 2) 33 #define CONV_MODE_MII 0 34 #define CONV_MODE_RMII 1 35 #define CONV_MODE_RGMII 2 36 37 #define MIIC_CONVCTRL_FULLD BIT(8) 38 #define MIIC_CONVCTRL_RGMII_LINK BIT(12) 39 #define MIIC_CONVCTRL_RGMII_DUPLEX BIT(13) 40 #define MIIC_CONVCTRL_RGMII_SPEED GENMASK(15, 14) 41 42 #define MIIC_CONVRST 0x114 43 #define MIIC_CONVRST_PHYIF_RST(port) BIT(port) 44 #define MIIC_CONVRST_PHYIF_RST_MASK GENMASK(4, 0) 45 46 #define MIIC_SWCTRL 0x304 47 #define MIIC_SWDUPC 0x308 48 49 #define MIIC_MAX_NR_PORTS 5 50 51 #define MIIC_MODCTRL_CONF_CONV_NUM 6 52 #define MIIC_MODCTRL_CONF_NONE -1 53 54 /** 55 * struct modctrl_match - Matching table entry for convctrl configuration 56 * See section 8.2.1 of manual. 57 * @mode_cfg: Configuration value for convctrl 58 * @conv: Configuration of ethernet port muxes. First index is SWITCH_PORTIN, 59 * then index 1 - 5 are CONV1 - CONV5. 60 */ 61 struct modctrl_match { 62 u32 mode_cfg; 63 u8 conv[MIIC_MODCTRL_CONF_CONV_NUM]; 64 }; 65 66 static struct modctrl_match modctrl_match_table[] = { 67 {0x0, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 68 MIIC_SWITCH_PORTC, MIIC_SERCOS_PORTB, MIIC_SERCOS_PORTA}}, 69 {0x1, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 70 MIIC_SWITCH_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}}, 71 {0x2, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 72 MIIC_ETHERCAT_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}}, 73 {0x3, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 74 MIIC_SWITCH_PORTC, MIIC_SWITCH_PORTB, MIIC_SWITCH_PORTA}}, 75 76 {0x8, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 77 MIIC_SWITCH_PORTC, MIIC_SERCOS_PORTB, MIIC_SERCOS_PORTA}}, 78 {0x9, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 79 MIIC_SWITCH_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}}, 80 {0xA, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 81 MIIC_ETHERCAT_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}}, 82 {0xB, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 83 MIIC_SWITCH_PORTC, MIIC_SWITCH_PORTB, MIIC_SWITCH_PORTA}}, 84 85 {0x10, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 86 MIIC_SWITCH_PORTC, MIIC_SERCOS_PORTB, MIIC_SERCOS_PORTA}}, 87 {0x11, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 88 MIIC_SWITCH_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}}, 89 {0x12, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 90 MIIC_ETHERCAT_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}}, 91 {0x13, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD, 92 MIIC_SWITCH_PORTC, MIIC_SWITCH_PORTB, MIIC_SWITCH_PORTA}} 93 }; 94 95 static const char * const conf_to_string[] = { 96 [MIIC_GMAC1_PORT] = "GMAC1_PORT", 97 [MIIC_GMAC2_PORT] = "GMAC2_PORT", 98 [MIIC_RTOS_PORT] = "RTOS_PORT", 99 [MIIC_SERCOS_PORTA] = "SERCOS_PORTA", 100 [MIIC_SERCOS_PORTB] = "SERCOS_PORTB", 101 [MIIC_ETHERCAT_PORTA] = "ETHERCAT_PORTA", 102 [MIIC_ETHERCAT_PORTB] = "ETHERCAT_PORTB", 103 [MIIC_ETHERCAT_PORTC] = "ETHERCAT_PORTC", 104 [MIIC_SWITCH_PORTA] = "SWITCH_PORTA", 105 [MIIC_SWITCH_PORTB] = "SWITCH_PORTB", 106 [MIIC_SWITCH_PORTC] = "SWITCH_PORTC", 107 [MIIC_SWITCH_PORTD] = "SWITCH_PORTD", 108 [MIIC_HSR_PORTA] = "HSR_PORTA", 109 [MIIC_HSR_PORTB] = "HSR_PORTB", 110 }; 111 112 static const char *index_to_string[MIIC_MODCTRL_CONF_CONV_NUM] = { 113 "SWITCH_PORTIN", 114 "CONV1", 115 "CONV2", 116 "CONV3", 117 "CONV4", 118 "CONV5", 119 }; 120 121 /** 122 * struct miic - MII converter structure 123 * @base: base address of the MII converter 124 * @dev: Device associated to the MII converter 125 * @lock: Lock used for read-modify-write access 126 */ 127 struct miic { 128 void __iomem *base; 129 struct device *dev; 130 spinlock_t lock; 131 }; 132 133 /** 134 * struct miic_port - Per port MII converter struct 135 * @miic: backiling to MII converter structure 136 * @pcs: PCS structure associated to the port 137 * @port: port number 138 * @interface: interface mode of the port 139 */ 140 struct miic_port { 141 struct miic *miic; 142 struct phylink_pcs pcs; 143 int port; 144 phy_interface_t interface; 145 }; 146 phylink_pcs_to_miic_port(struct phylink_pcs * pcs)147 static struct miic_port *phylink_pcs_to_miic_port(struct phylink_pcs *pcs) 148 { 149 return container_of(pcs, struct miic_port, pcs); 150 } 151 miic_reg_writel(struct miic * miic,int offset,u32 value)152 static void miic_reg_writel(struct miic *miic, int offset, u32 value) 153 { 154 writel(value, miic->base + offset); 155 } 156 miic_reg_readl(struct miic * miic,int offset)157 static u32 miic_reg_readl(struct miic *miic, int offset) 158 { 159 return readl(miic->base + offset); 160 } 161 miic_reg_rmw(struct miic * miic,int offset,u32 mask,u32 val)162 static void miic_reg_rmw(struct miic *miic, int offset, u32 mask, u32 val) 163 { 164 u32 reg; 165 166 spin_lock(&miic->lock); 167 168 reg = miic_reg_readl(miic, offset); 169 reg &= ~mask; 170 reg |= val; 171 miic_reg_writel(miic, offset, reg); 172 173 spin_unlock(&miic->lock); 174 } 175 miic_converter_enable(struct miic * miic,int port,int enable)176 static void miic_converter_enable(struct miic *miic, int port, int enable) 177 { 178 u32 val = 0; 179 180 if (enable) 181 val = MIIC_CONVRST_PHYIF_RST(port); 182 183 miic_reg_rmw(miic, MIIC_CONVRST, MIIC_CONVRST_PHYIF_RST(port), val); 184 } 185 miic_config(struct phylink_pcs * pcs,unsigned int neg_mode,phy_interface_t interface,const unsigned long * advertising,bool permit)186 static int miic_config(struct phylink_pcs *pcs, unsigned int neg_mode, 187 phy_interface_t interface, 188 const unsigned long *advertising, bool permit) 189 { 190 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs); 191 struct miic *miic = miic_port->miic; 192 u32 speed, conv_mode, val, mask; 193 int port = miic_port->port; 194 195 switch (interface) { 196 case PHY_INTERFACE_MODE_RMII: 197 conv_mode = CONV_MODE_RMII; 198 speed = CONV_MODE_100MBPS; 199 break; 200 case PHY_INTERFACE_MODE_RGMII: 201 case PHY_INTERFACE_MODE_RGMII_ID: 202 case PHY_INTERFACE_MODE_RGMII_TXID: 203 case PHY_INTERFACE_MODE_RGMII_RXID: 204 conv_mode = CONV_MODE_RGMII; 205 speed = CONV_MODE_1000MBPS; 206 break; 207 case PHY_INTERFACE_MODE_MII: 208 conv_mode = CONV_MODE_MII; 209 /* When in MII mode, speed should be set to 0 (which is actually 210 * CONV_MODE_10MBPS) 211 */ 212 speed = CONV_MODE_10MBPS; 213 break; 214 default: 215 return -EOPNOTSUPP; 216 } 217 218 val = FIELD_PREP(MIIC_CONVCTRL_CONV_MODE, conv_mode); 219 mask = MIIC_CONVCTRL_CONV_MODE; 220 221 /* Update speed only if we are going to change the interface because 222 * the link might already be up and it would break it if the speed is 223 * changed. 224 */ 225 if (interface != miic_port->interface) { 226 val |= FIELD_PREP(MIIC_CONVCTRL_CONV_SPEED, speed); 227 mask |= MIIC_CONVCTRL_CONV_SPEED; 228 miic_port->interface = interface; 229 } 230 231 miic_reg_rmw(miic, MIIC_CONVCTRL(port), mask, val); 232 miic_converter_enable(miic, miic_port->port, 1); 233 234 return 0; 235 } 236 miic_link_up(struct phylink_pcs * pcs,unsigned int neg_mode,phy_interface_t interface,int speed,int duplex)237 static void miic_link_up(struct phylink_pcs *pcs, unsigned int neg_mode, 238 phy_interface_t interface, int speed, int duplex) 239 { 240 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs); 241 struct miic *miic = miic_port->miic; 242 u32 conv_speed = 0, val = 0; 243 int port = miic_port->port; 244 245 if (duplex == DUPLEX_FULL) 246 val |= MIIC_CONVCTRL_FULLD; 247 248 /* No speed in MII through-mode */ 249 if (interface != PHY_INTERFACE_MODE_MII) { 250 switch (speed) { 251 case SPEED_1000: 252 conv_speed = CONV_MODE_1000MBPS; 253 break; 254 case SPEED_100: 255 conv_speed = CONV_MODE_100MBPS; 256 break; 257 case SPEED_10: 258 conv_speed = CONV_MODE_10MBPS; 259 break; 260 default: 261 return; 262 } 263 } 264 265 val |= FIELD_PREP(MIIC_CONVCTRL_CONV_SPEED, conv_speed); 266 267 miic_reg_rmw(miic, MIIC_CONVCTRL(port), 268 (MIIC_CONVCTRL_CONV_SPEED | MIIC_CONVCTRL_FULLD), val); 269 } 270 miic_validate(struct phylink_pcs * pcs,unsigned long * supported,const struct phylink_link_state * state)271 static int miic_validate(struct phylink_pcs *pcs, unsigned long *supported, 272 const struct phylink_link_state *state) 273 { 274 if (phy_interface_mode_is_rgmii(state->interface) || 275 state->interface == PHY_INTERFACE_MODE_RMII || 276 state->interface == PHY_INTERFACE_MODE_MII) 277 return 1; 278 279 return -EINVAL; 280 } 281 miic_pre_init(struct phylink_pcs * pcs)282 static int miic_pre_init(struct phylink_pcs *pcs) 283 { 284 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs); 285 struct miic *miic = miic_port->miic; 286 u32 val, mask; 287 288 /* Start RX clock if required */ 289 if (pcs->rxc_always_on) { 290 /* In MII through mode, the clock signals will be driven by the 291 * external PHY, which might not be initialized yet. Set RMII 292 * as default mode to ensure that a reference clock signal is 293 * generated. 294 */ 295 miic_port->interface = PHY_INTERFACE_MODE_RMII; 296 297 val = FIELD_PREP(MIIC_CONVCTRL_CONV_MODE, CONV_MODE_RMII) | 298 FIELD_PREP(MIIC_CONVCTRL_CONV_SPEED, CONV_MODE_100MBPS); 299 mask = MIIC_CONVCTRL_CONV_MODE | MIIC_CONVCTRL_CONV_SPEED; 300 301 miic_reg_rmw(miic, MIIC_CONVCTRL(miic_port->port), mask, val); 302 303 miic_converter_enable(miic, miic_port->port, 1); 304 } 305 306 return 0; 307 } 308 309 static const struct phylink_pcs_ops miic_phylink_ops = { 310 .pcs_validate = miic_validate, 311 .pcs_config = miic_config, 312 .pcs_link_up = miic_link_up, 313 .pcs_pre_init = miic_pre_init, 314 }; 315 miic_create(struct device * dev,struct device_node * np)316 struct phylink_pcs *miic_create(struct device *dev, struct device_node *np) 317 { 318 struct platform_device *pdev; 319 struct miic_port *miic_port; 320 struct device_node *pcs_np; 321 struct miic *miic; 322 u32 port; 323 324 if (!of_device_is_available(np)) 325 return ERR_PTR(-ENODEV); 326 327 if (of_property_read_u32(np, "reg", &port)) 328 return ERR_PTR(-EINVAL); 329 330 if (port > MIIC_MAX_NR_PORTS || port < 1) 331 return ERR_PTR(-EINVAL); 332 333 /* The PCS pdev is attached to the parent node */ 334 pcs_np = of_get_parent(np); 335 if (!pcs_np) 336 return ERR_PTR(-ENODEV); 337 338 if (!of_device_is_available(pcs_np)) { 339 of_node_put(pcs_np); 340 return ERR_PTR(-ENODEV); 341 } 342 343 pdev = of_find_device_by_node(pcs_np); 344 of_node_put(pcs_np); 345 if (!pdev || !platform_get_drvdata(pdev)) { 346 if (pdev) 347 put_device(&pdev->dev); 348 return ERR_PTR(-EPROBE_DEFER); 349 } 350 351 miic_port = kzalloc(sizeof(*miic_port), GFP_KERNEL); 352 if (!miic_port) { 353 put_device(&pdev->dev); 354 return ERR_PTR(-ENOMEM); 355 } 356 357 miic = platform_get_drvdata(pdev); 358 device_link_add(dev, miic->dev, DL_FLAG_AUTOREMOVE_CONSUMER); 359 put_device(&pdev->dev); 360 361 miic_port->miic = miic; 362 miic_port->port = port - 1; 363 miic_port->pcs.ops = &miic_phylink_ops; 364 miic_port->pcs.neg_mode = true; 365 366 return &miic_port->pcs; 367 } 368 EXPORT_SYMBOL(miic_create); 369 miic_destroy(struct phylink_pcs * pcs)370 void miic_destroy(struct phylink_pcs *pcs) 371 { 372 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs); 373 374 miic_converter_enable(miic_port->miic, miic_port->port, 0); 375 kfree(miic_port); 376 } 377 EXPORT_SYMBOL(miic_destroy); 378 miic_init_hw(struct miic * miic,u32 cfg_mode)379 static int miic_init_hw(struct miic *miic, u32 cfg_mode) 380 { 381 int port; 382 383 /* Unlock write access to accessory registers (cf datasheet). If this 384 * is going to be used in conjunction with the Cortex-M3, this sequence 385 * will have to be moved in register write 386 */ 387 miic_reg_writel(miic, MIIC_PRCMD, 0x00A5); 388 miic_reg_writel(miic, MIIC_PRCMD, 0x0001); 389 miic_reg_writel(miic, MIIC_PRCMD, 0xFFFE); 390 miic_reg_writel(miic, MIIC_PRCMD, 0x0001); 391 392 miic_reg_writel(miic, MIIC_MODCTRL, 393 FIELD_PREP(MIIC_MODCTRL_SW_MODE, cfg_mode)); 394 395 for (port = 0; port < MIIC_MAX_NR_PORTS; port++) { 396 miic_converter_enable(miic, port, 0); 397 /* Disable speed/duplex control from these registers, datasheet 398 * says switch registers should be used to setup switch port 399 * speed and duplex. 400 */ 401 miic_reg_writel(miic, MIIC_SWCTRL, 0x0); 402 miic_reg_writel(miic, MIIC_SWDUPC, 0x0); 403 } 404 405 return 0; 406 } 407 miic_modctrl_match(s8 table_val[MIIC_MODCTRL_CONF_CONV_NUM],s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM])408 static bool miic_modctrl_match(s8 table_val[MIIC_MODCTRL_CONF_CONV_NUM], 409 s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM]) 410 { 411 int i; 412 413 for (i = 0; i < MIIC_MODCTRL_CONF_CONV_NUM; i++) { 414 if (dt_val[i] == MIIC_MODCTRL_CONF_NONE) 415 continue; 416 417 if (dt_val[i] != table_val[i]) 418 return false; 419 } 420 421 return true; 422 } 423 miic_dump_conf(struct device * dev,s8 conf[MIIC_MODCTRL_CONF_CONV_NUM])424 static void miic_dump_conf(struct device *dev, 425 s8 conf[MIIC_MODCTRL_CONF_CONV_NUM]) 426 { 427 const char *conf_name; 428 int i; 429 430 for (i = 0; i < MIIC_MODCTRL_CONF_CONV_NUM; i++) { 431 if (conf[i] != MIIC_MODCTRL_CONF_NONE) 432 conf_name = conf_to_string[conf[i]]; 433 else 434 conf_name = "NONE"; 435 436 dev_err(dev, "%s: %s\n", index_to_string[i], conf_name); 437 } 438 } 439 miic_match_dt_conf(struct device * dev,s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM],u32 * mode_cfg)440 static int miic_match_dt_conf(struct device *dev, 441 s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM], 442 u32 *mode_cfg) 443 { 444 struct modctrl_match *table_entry; 445 int i; 446 447 for (i = 0; i < ARRAY_SIZE(modctrl_match_table); i++) { 448 table_entry = &modctrl_match_table[i]; 449 450 if (miic_modctrl_match(table_entry->conv, dt_val)) { 451 *mode_cfg = table_entry->mode_cfg; 452 return 0; 453 } 454 } 455 456 dev_err(dev, "Failed to apply requested configuration\n"); 457 miic_dump_conf(dev, dt_val); 458 459 return -EINVAL; 460 } 461 miic_parse_dt(struct device * dev,u32 * mode_cfg)462 static int miic_parse_dt(struct device *dev, u32 *mode_cfg) 463 { 464 s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM]; 465 struct device_node *np = dev->of_node; 466 struct device_node *conv; 467 u32 conf; 468 int port; 469 470 memset(dt_val, MIIC_MODCTRL_CONF_NONE, sizeof(dt_val)); 471 472 if (of_property_read_u32(np, "renesas,miic-switch-portin", &conf) == 0) 473 dt_val[0] = conf; 474 475 for_each_child_of_node(np, conv) { 476 if (of_property_read_u32(conv, "reg", &port)) 477 continue; 478 479 if (!of_device_is_available(conv)) 480 continue; 481 482 if (of_property_read_u32(conv, "renesas,miic-input", &conf) == 0) 483 dt_val[port] = conf; 484 } 485 486 return miic_match_dt_conf(dev, dt_val, mode_cfg); 487 } 488 miic_probe(struct platform_device * pdev)489 static int miic_probe(struct platform_device *pdev) 490 { 491 struct device *dev = &pdev->dev; 492 struct miic *miic; 493 u32 mode_cfg; 494 int ret; 495 496 ret = miic_parse_dt(dev, &mode_cfg); 497 if (ret < 0) 498 return ret; 499 500 miic = devm_kzalloc(dev, sizeof(*miic), GFP_KERNEL); 501 if (!miic) 502 return -ENOMEM; 503 504 spin_lock_init(&miic->lock); 505 miic->dev = dev; 506 miic->base = devm_platform_ioremap_resource(pdev, 0); 507 if (IS_ERR(miic->base)) 508 return PTR_ERR(miic->base); 509 510 ret = devm_pm_runtime_enable(dev); 511 if (ret < 0) 512 return ret; 513 514 ret = pm_runtime_resume_and_get(dev); 515 if (ret < 0) 516 return ret; 517 518 ret = miic_init_hw(miic, mode_cfg); 519 if (ret) 520 goto disable_runtime_pm; 521 522 /* miic_create() relies on that fact that data are attached to the 523 * platform device to determine if the driver is ready so this needs to 524 * be the last thing to be done after everything is initialized 525 * properly. 526 */ 527 platform_set_drvdata(pdev, miic); 528 529 return 0; 530 531 disable_runtime_pm: 532 pm_runtime_put(dev); 533 534 return ret; 535 } 536 miic_remove(struct platform_device * pdev)537 static void miic_remove(struct platform_device *pdev) 538 { 539 pm_runtime_put(&pdev->dev); 540 } 541 542 static const struct of_device_id miic_of_mtable[] = { 543 { .compatible = "renesas,rzn1-miic" }, 544 { /* sentinel */ }, 545 }; 546 MODULE_DEVICE_TABLE(of, miic_of_mtable); 547 548 static struct platform_driver miic_driver = { 549 .driver = { 550 .name = "rzn1_miic", 551 .suppress_bind_attrs = true, 552 .of_match_table = miic_of_mtable, 553 }, 554 .probe = miic_probe, 555 .remove_new = miic_remove, 556 }; 557 module_platform_driver(miic_driver); 558 559 MODULE_LICENSE("GPL"); 560 MODULE_DESCRIPTION("Renesas MII converter PCS driver"); 561 MODULE_AUTHOR("Clément Léger <clement.leger@bootlin.com>"); 562