Home
last modified time | relevance | path

Searched refs:DIP (Results 1 – 17 of 17) sorted by relevance

/linux-6.12.1/arch/arm64/boot/dts/renesas/
Dr9a07g043u11-smarc.dts11 * DIP-Switch SW1 setting
22 * - Set DIP-Switch SW1-3 to On position.
Dr9a07g044c2-smarc.dts11 * DIP-Switch SW1 setting on SoM
40 * - Set DIP-Switch SW1-4 to Off position.
/linux-6.12.1/arch/riscv/boot/dts/renesas/
Dr9a07g043f01-smarc.dts11 * DIP-Switch SW1 setting
/linux-6.12.1/arch/sh/boards/
DKconfig215 DIP switch(S2-5). If you set the DIP switch for S2-5 = ON,
/linux-6.12.1/Documentation/networking/devlink/
Dprestera.rst129 - Drops packets with illegal SIP/DIP multicast/unicast addresses.
/linux-6.12.1/arch/x86/kvm/
Demulate.c3955 #define DIP(_y, _i, _p) { .flags = (_y)|Intercept|CheckPerm, \ macro
3974 #define D2bvIP(_f, _i, _p) DIP((_f) | ByteOp, _i, _p), DIP(_f, _i, _p)
4003 DIP(SrcNone | Prot | Priv, vmrun, check_svme_pa),
4005 DIP(SrcNone | Prot | Priv, vmload, check_svme_pa),
4006 DIP(SrcNone | Prot | Priv, vmsave, check_svme_pa),
4007 DIP(SrcNone | Prot | Priv, stgi, check_svme),
4008 DIP(SrcNone | Prot | Priv, clgi, check_svme),
4009 DIP(SrcNone | Prot | Priv, skinit, check_svme),
4010 DIP(SrcNone | Prot | Priv, invlpga, check_svme),
4015 DIP(SrcNone, rdtscp, check_rdtsc),
[all …]
/linux-6.12.1/drivers/scsi/sym53c8xx_2/
Dsym_defs.h172 #define DIP 0x01 /* sta: host/script interrupt */ macro
Dsym_hipd.c153 else if (istat & DIP) { in sym_soft_reset()
1025 if (INB(np, nc_istat) & (INTF|SIP|DIP))
2827 if (!(istat & (SIP|DIP)))
2851 if (istatc & DIP)
2862 } while (istatc & (SIP|DIP));
/linux-6.12.1/tools/testing/selftests/net/forwarding/
Dlib.sh2193 )"$(ipv6_to_bytes $GRP):"$( : DIP is multicast address
2228 )"$(ipv6_to_bytes $GRP):"$( : DIP is multicast address
/linux-6.12.1/arch/arm/boot/dts/ti/omap/
Dam3517-evm.dts216 /* User DIP swithes [1:8] / User LEDS [1:2] */
Ddra72-evm-common.dtsi317 /* To use NAND, DIP switch SW5 must be set like so:
/linux-6.12.1/Documentation/networking/
Darcnet-hardware.rst1063 SW1: DIP-Switches for Station Address
1064 SW2: DIP-Switches for Memory Base and I/O Base addresses
1083 (DIP-Switch downwards means "0")
1087 The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
1104 DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range:
1208 DIP Switches:
1210 The DIP switches accessible on the accessible end of the card while
1227 There is another array of eight DIP switches at the top of the
1233 are in a weird order. This was tested by setting the DIP switches,
2323 There is a DIP-switch with 8 switches, used to set the shared memory address
D6pack.rst79 is supplied with a DIP switch so you can easily change between the
Darcnet.rst161 default which is still set in DIP switches on the card. If you don't have the
/linux-6.12.1/drivers/scsi/
Dncr53c8xx.h693 #define DIP 0x01 /* sta: host/script interrupt */ macro
Dncr53c8xx.c5606 if (INB(nc_istat) & (INTF|SIP|DIP)) { in ncr_timeout()
5749 if (!(istat & (SIP|DIP))) in ncr_exception()
5761 dstat = (istat & DIP) ? INB (nc_dstat) : 0; in ncr_exception()
7566 if (INB(nc_istat) & (INTF|SIP|DIP))
/linux-6.12.1/drivers/gpio/
DKconfig1248 includes reads of pushbuttons and DIP switches as well