Searched refs:CRT (Results 1 – 16 of 16) sorted by relevance
| /linux-6.12.1/Documentation/fb/ |
| D | viafb.rst | 16 Device: CRT, LCD, DVI
20 CRT:
42 viafb_active_dev=CRT+DVI viafb_dvi_port=DVP1
109 This option is used to specify active devices.(CRT, DVI, CRT+LCD...)
121 To enable two devices, such as CRT+DVI::
123 modprobe viafb viafb_active_dev=CRT+DVI;
127 modprobe viafb viafb_active_dev=CRT+DVI
131 modprobe viafb viafb_active_dev=DVI+CRT...
135 If CRT is primary and DVI is secondary, we should use::
137 modprobe viafb viafb_active_dev=CRT+DVI viafb_SAMM_ON=1...
[all …]
|
| D | modedb.rst | 104 The GTF is limited by the fact that it is designed mainly for CRT displays.
110 The CVT addresses these limitations. If used with CRT's, the formula used
117 new CRT displays and probably with most flatpanels, if 'reduced blanking'
|
| /linux-6.12.1/Documentation/ABI/testing/ |
| D | sysfs-platform-eeepc-laptop | 9 - 2 = CRT
10 - 3 = LCD+CRT
|
| D | sysfs-platform-asus-laptop | 11 ||`-- CRT
17 - 3 (0011b) CRT+LCD.
|
| /linux-6.12.1/arch/sh/cchips/ |
| D | Kconfig | 17 CRT color controller, IrDA up to 4 Mbps, and a
|
| /linux-6.12.1/drivers/gpu/drm/nouveau/nvkm/engine/disp/ |
| D | ior.h | 27 CRT, enumerator
|
| D | outp.c | 67 case DCB_OUTPUT_ANALOG: *type = DAC; return CRT; in nvkm_outp_xlat()
|
| D | uoutp.c | 413 if (ior->arm.proto != CRT) in nvkm_uoutp_mthd_inherit()
|
| D | gf119.c | 368 case 0: state->proto = CRT; break; in gf119_dac_state()
|
| D | nv50.c | 338 case 0: state->proto = CRT; break; in nv50_dac_state()
|
| /linux-6.12.1/Documentation/admin-guide/laptops/ |
| D | asus-laptop.rst | 123 | Bin | Val | DVI | TV | CRT | LCD |
|
| D | thinkpad-acpi.rst | 663 LCD, CRT or DVI (if available). The following commands are available::
|
| /linux-6.12.1/drivers/video/fbdev/ |
| D | cirrusfb.c | 349 CRT, enumerator
2833 case CRT: in cirrusfb_dbg_print_regs()
2867 cirrusfb_dbg_print_regs(info, regbase, CRT, in cirrusfb_dbg_reg_dump()
|
| D | Kconfig | 1566 Frame buffer driver for the CRT and LCD controllers in the Silicon
|
| /linux-6.12.1/drivers/pinctrl/tegra/ |
| D | pinctrl-tegra20.c | 2053 MUX_PG(crtp, CRT, RSVD2, RSVD3, RSVD4, 0x20, 14, 0x98, 20, 0xa4, 24),
2110 MUX_PG(lm1, DISPLAYA, DISPLAYB, RSVD3, CRT, 0x1c, 25, 0x90, 28, -1, -1),
|
| D | pinctrl-tegra30.c | 2345 …PINGROUP(crt_hsync_pv6, CRT, RSVD2, RSVD3, RSVD4, 0x311c, N, …
2346 …PINGROUP(crt_vsync_pv7, CRT, RSVD2, RSVD3, RSVD4, 0x3120, N, …
|