| /linux-6.12.1/Documentation/admin-guide/media/ |
| D | dvb_intro.rst | 133 T 177500000 7MHz AUTO AUTO QAM64 8k 1/16 NONE
134 T 184500000 7MHz AUTO AUTO QAM64 8k 1/8 NONE
135 T 191625000 7MHz AUTO AUTO QAM64 8k 1/16 NONE
136 T 219500000 7MHz AUTO AUTO QAM64 8k 1/16 NONE
137 T 226500000 7MHz AUTO AUTO QAM64 8k 1/16 NONE
138 T 557625000 7MHz AUTO AUTO QPSK 8k 1/16 NONE
148 CODE_RATE_HP = AUTO
149 CODE_RATE_LP = AUTO
154 INVERSION = AUTO
|
| /linux-6.12.1/Documentation/ABI/testing/ |
| D | sysfs-driver-toshiba_acpi | 9 * 0x2 -> AUTO (also called TIMER)
15 AUTO).
25 whenever the operation mode is set to AUTO (or TIMER),
60 * 0x2 -> AUTO (also called TIMER)
75 * 1 -> Type 1, supporting modes FN-Z and AUTO
|
| D | sysfs-bus-i2c-devices-fsa9480 | 26 AUTO switch automatically by device
|
| /linux-6.12.1/drivers/firmware/microchip/ |
| D | Kconfig | 4 tristate "Microchip PolarFire SoC AUTO UPDATE"
|
| /linux-6.12.1/Documentation/userspace-api/media/dvb/ |
| D | fe-bandwidth-t.rst | 22 - .. _BANDWIDTH-AUTO:
|
| D | fe_property_parameters.rst | 293 Possible values: 0, 1, -1 (AUTO)
307 Possible values: 0, 1, -1 (AUTO)
344 Possible values: 0 .. 41, -1 (AUTO)
474 Possible values: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, -1 (AUTO)
565 Valid values: 0, 1, 2, 4, -1 (AUTO)
|
| /linux-6.12.1/drivers/net/wireless/broadcom/brcm80211/include/ |
| D | defs.h | 21 #define AUTO (-1) /* Auto = -1 */ macro
|
| /linux-6.12.1/drivers/regulator/ |
| D | pcf50633-regulator.c | 51 PCF50633_REGULATOR("auto", AUTO, 1800000, 25000, 0x2f, 128),
|
| /linux-6.12.1/Documentation/hwmon/ |
| D | da9055.rst | 36 Voltages are sampled in a AUTO mode it can be manually sampled too and results
|
| /linux-6.12.1/Documentation/driver-api/thermal/ |
| D | nouveau_thermal.rst | 62 Current fan management mode (NONE, MANUAL or AUTO);
|
| /linux-6.12.1/Documentation/networking/device_drivers/wifi/intel/ |
| D | ipw2100.rst | 258 last set level (defaults to AUTO)
259 iwpriv eth1 set_power 0 Sets power level to AUTO and enables
|
| /linux-6.12.1/drivers/net/wireless/broadcom/brcm80211/brcmsmac/ |
| D | ampdu.c | 241 ampdu->max_pdu = AUTO; in brcms_c_ampdu_attach()
292 if (ampdu->max_pdu != AUTO) in brcms_c_scb_ampdu_update_config()
|
| D | main.h | 219 (wlc)->band->band_stf_stbc_tx == AUTO && \
|
| D | stf.c | 133 if ((int_val != AUTO) && (int_val != OFF) && (int_val != ON)) in brcms_c_stf_stbc_tx_set()
|
| D | main.c | 4301 brcms_c_protection_upd(wlc, BRCMS_PROT_N_PAM_OVR, AUTO); in brcms_c_info_init()
5294 s32 nmode = AUTO; in brcms_c_set_nmode()
6338 } else if (wlc->mimo_40txbw != AUTO) in brcms_c_d11hdrs_mac80211()
6344 if (wlc->ofdm_40txbw != AUTO) in brcms_c_d11hdrs_mac80211()
6346 } else if (wlc->cck_40txbw != AUTO) { in brcms_c_d11hdrs_mac80211()
8033 wlc->mimo_40txbw = AUTO; in brcms_c_attach()
8034 wlc->ofdm_40txbw = AUTO; in brcms_c_attach()
8035 wlc->cck_40txbw = AUTO; in brcms_c_attach()
|
| /linux-6.12.1/Documentation/driver-api/media/drivers/ |
| D | vidtv.rst | 356 MODULATION = QAM/AUTO
358 INNER_FEC = AUTO
|
| /linux-6.12.1/drivers/gpu/drm/nouveau/dispnv50/ |
| D | head507d.c | 41 NVDEF(NV507D, HEAD_SET_PROCAMP, CHROMA_LPF, AUTO) | in head507d_procamp()
|
| D | head907d.c | 69 NVDEF(NV907D, HEAD_SET_PROCAMP, CHROMA_LPF, AUTO) | in head907d_procamp()
|
| /linux-6.12.1/drivers/gpu/drm/tegra/ |
| D | hdmi.c | 109 AUTO = 0, enumerator
1807 hdmi->audio_source = AUTO; in tegra_hdmi_probe()
|
| /linux-6.12.1/Documentation/userspace-api/media/v4l/ |
| D | ext-ctrls-camera.rst | 59 When ``V4L2_CID_EXPOSURE_AUTO`` is set to ``AUTO`` or
66 when ``V4L2_CID_EXPOSURE_AUTO`` control is set to ``AUTO``,
|
| /linux-6.12.1/drivers/platform/x86/ |
| D | sony-laptop.c | 2440 AUTO enumerator
2475 return result & 0x80 ? AUTO : in __sony_nc_gfx_switch_status_get()
2493 pos == AUTO ? "auto" : "unknown"); in sony_nc_gfx_switch_status_show()
|
| /linux-6.12.1/drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/ |
| D | phy_n.c | 14617 pi->n_preamble_override = AUTO; in wlc_phy_attach_nphy()
14621 pi->nphy_txrx_chain = AUTO; in wlc_phy_attach_nphy()
14622 pi->phy_scraminit = AUTO; in wlc_phy_attach_nphy()
14635 pi->nphy_txpwrindex[i].index = AUTO; in wlc_phy_attach_nphy()
|