Searched refs:ATA (Results 1 – 25 of 51) sorted by relevance
123
14 menuconfig ATA config15 tristate "Serial ATA and Parallel ATA drivers (libata)"21 If you want to use an ATA hard disk, ATA tape drive, ATA CD-ROM or22 any other ATA device under Linux, say Y and make sure that you know23 the name of your ATA host adapter (the card inside your computer24 that "speaks" the ATA protocol, also called ATA controller),27 NOTE: ATA enables basic SCSI support; *however*,32 if ATA44 bool "Verbose ATA error reporting"47 This option adds parsing of ATA command descriptions and error bits[all …]
10 libATA is a library used inside the Linux kernel to support ATA host11 controllers and devices. libATA provides an ATA driver API, class12 transports for ATA and ATAPI devices, and SCSI<->ATA translation for ATA16 internals, and a couple sample ATA low-level drivers.24 with the ATA and SCSI layers.29 defining at a bare minimum the bus I/O addresses of the ATA shadow107 ATA command execute115 causes an ATA command, previously loaded with ``->tf_load()``, to be127 Allow low-level driver to filter ATA PACKET commands, returning a status134 Read specific ATA shadow registers[all …]
18 bool "ATA support for libsas (requires libata)"20 depends on ATA = y || ATA = SCSI_SAS_LIBSAS23 Builds in ATA support into libsas. Will necessitate
27 ATA, /* ATA */ enumerator39 INTC_IRQ(ATA, IRQ_ATA),48 { BUTTON, POWER, FATA, ATA,
14 optional for some drivers (like ATA), but required for24 This option enables the support for the ATA task.
11 Information technology - AT Attachment 8 - ATA/ATAPI Command Set (ATA8-ACS)17 Information technology - SCSI / ATA Translation - 5 (SAT-5)26 If supported, it uses the ATA SCT Command Transport feature to read
21 ATA/ATAPI-7 specifies the IDLE IMMEDIATE command with unload feature.39 For each ATA device, the kernel exports the file76 reality. In fact, the ATA specs clearly state that the time for an77 unload operation to complete is vendor specific. The hint in ATA-779 been dropped in ATA-8.109 version of the ATA standard than ATA-7, but do support the unload
2 ATA over Ethernet (AoE)
4 ATA over Ethernet is a network protocol that provides simple access to52 limit ATA over Ethernet traffic to eth2 and eth4. AoE traffic from127 all network interfaces may be used for ATA over Ethernet. Here is a
12 Because ATA over Ethernet is not fragmented by the kernel's IP code,
16 select ATA_NONSTANDARD if ATA
38 libata: Un-break ATA blacklist
65 tristate "ISD-200 USB/ATA Bridge support"68 on the In-Systems Design ISD-200 USB/ATA bridge.167 tristate "SAT emulation on Cypress USB/ATA Bridge with ATACB"170 on the Cypress USB/ATA bridge supporting ATACB. This will allow you
8 depends on ATA
3 SATA nodes are defined to describe on-chip Serial ATA controllers.
3 SATA host controller nodes are defined to describe on-chip Serial ATA
123 ATA drive identity information. For full description, see125 the ATA specification.171 If you don't have a copy of the ANSI ATA specification174 - Execute an ATA disk command directly by writing the "taskfile"397 Note: If you don't have a copy of the ANSI ATA specification472 Note: If you don't have a copy of the ANSI ATA specification
3 Provide a place in sysfs for storing the ATA topology of the4 system. This allows retrieving various information about ATA
41 ATA standard, but support the unload feature nonetheless.106 limits feature found in some ATA and SCSI devices.
36 libata: Un-break ATA blacklist
131 /* Apalis Serial ATA */
129 /* Apalis Serial ATA */
37 depends on ATA
46 key "passphrase" is expected to be 32bytes long. This is similar to the ATA
177 # Example: Display ATA port reset as ataN_port_reset in the timeline