1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * st-asc.c: ST Asynchronous serial controller (ASC) driver
4 *
5 * Copyright (C) 2003-2013 STMicroelectronics (R&D) Limited
6 */
7
8 #include <linux/module.h>
9 #include <linux/serial.h>
10 #include <linux/console.h>
11 #include <linux/sysrq.h>
12 #include <linux/pinctrl/consumer.h>
13 #include <linux/platform_device.h>
14 #include <linux/io.h>
15 #include <linux/irq.h>
16 #include <linux/tty.h>
17 #include <linux/tty_flip.h>
18 #include <linux/delay.h>
19 #include <linux/spinlock.h>
20 #include <linux/of.h>
21 #include <linux/of_platform.h>
22 #include <linux/serial_core.h>
23 #include <linux/clk.h>
24 #include <linux/gpio/consumer.h>
25
26 #define DRIVER_NAME "st-asc"
27 #define ASC_SERIAL_NAME "ttyAS"
28 #define ASC_FIFO_SIZE 16
29 #define ASC_MAX_PORTS 8
30
31 /* Pinctrl states */
32 #define DEFAULT 0
33 #define NO_HW_FLOWCTRL 1
34
35 struct asc_port {
36 struct uart_port port;
37 struct gpio_desc *rts;
38 struct clk *clk;
39 struct pinctrl *pinctrl;
40 struct pinctrl_state *states[2];
41 unsigned int hw_flow_control:1;
42 unsigned int force_m1:1;
43 };
44
45 static struct asc_port asc_ports[ASC_MAX_PORTS];
46 static struct uart_driver asc_uart_driver;
47
48 /*---- UART Register definitions ------------------------------*/
49
50 /* Register offsets */
51
52 #define ASC_BAUDRATE 0x00
53 #define ASC_TXBUF 0x04
54 #define ASC_RXBUF 0x08
55 #define ASC_CTL 0x0C
56 #define ASC_INTEN 0x10
57 #define ASC_STA 0x14
58 #define ASC_GUARDTIME 0x18
59 #define ASC_TIMEOUT 0x1C
60 #define ASC_TXRESET 0x20
61 #define ASC_RXRESET 0x24
62 #define ASC_RETRIES 0x28
63
64 /* ASC_RXBUF */
65 #define ASC_RXBUF_PE 0x100
66 #define ASC_RXBUF_FE 0x200
67 /*
68 * Some of status comes from higher bits of the character and some come from
69 * the status register. Combining both of them in to single status using dummy
70 * bits.
71 */
72 #define ASC_RXBUF_DUMMY_RX 0x10000
73 #define ASC_RXBUF_DUMMY_BE 0x20000
74 #define ASC_RXBUF_DUMMY_OE 0x40000
75
76 /* ASC_CTL */
77
78 #define ASC_CTL_MODE_MSK 0x0007
79 #define ASC_CTL_MODE_8BIT 0x0001
80 #define ASC_CTL_MODE_7BIT_PAR 0x0003
81 #define ASC_CTL_MODE_9BIT 0x0004
82 #define ASC_CTL_MODE_8BIT_WKUP 0x0005
83 #define ASC_CTL_MODE_8BIT_PAR 0x0007
84 #define ASC_CTL_STOP_MSK 0x0018
85 #define ASC_CTL_STOP_HALFBIT 0x0000
86 #define ASC_CTL_STOP_1BIT 0x0008
87 #define ASC_CTL_STOP_1_HALFBIT 0x0010
88 #define ASC_CTL_STOP_2BIT 0x0018
89 #define ASC_CTL_PARITYODD 0x0020
90 #define ASC_CTL_LOOPBACK 0x0040
91 #define ASC_CTL_RUN 0x0080
92 #define ASC_CTL_RXENABLE 0x0100
93 #define ASC_CTL_SCENABLE 0x0200
94 #define ASC_CTL_FIFOENABLE 0x0400
95 #define ASC_CTL_CTSENABLE 0x0800
96 #define ASC_CTL_BAUDMODE 0x1000
97
98 /* ASC_GUARDTIME */
99
100 #define ASC_GUARDTIME_MSK 0x00FF
101
102 /* ASC_INTEN */
103
104 #define ASC_INTEN_RBE 0x0001
105 #define ASC_INTEN_TE 0x0002
106 #define ASC_INTEN_THE 0x0004
107 #define ASC_INTEN_PE 0x0008
108 #define ASC_INTEN_FE 0x0010
109 #define ASC_INTEN_OE 0x0020
110 #define ASC_INTEN_TNE 0x0040
111 #define ASC_INTEN_TOI 0x0080
112 #define ASC_INTEN_RHF 0x0100
113
114 /* ASC_RETRIES */
115
116 #define ASC_RETRIES_MSK 0x00FF
117
118 /* ASC_RXBUF */
119
120 #define ASC_RXBUF_MSK 0x03FF
121
122 /* ASC_STA */
123
124 #define ASC_STA_RBF 0x0001
125 #define ASC_STA_TE 0x0002
126 #define ASC_STA_THE 0x0004
127 #define ASC_STA_PE 0x0008
128 #define ASC_STA_FE 0x0010
129 #define ASC_STA_OE 0x0020
130 #define ASC_STA_TNE 0x0040
131 #define ASC_STA_TOI 0x0080
132 #define ASC_STA_RHF 0x0100
133 #define ASC_STA_TF 0x0200
134 #define ASC_STA_NKD 0x0400
135
136 /* ASC_TIMEOUT */
137
138 #define ASC_TIMEOUT_MSK 0x00FF
139
140 /* ASC_TXBUF */
141
142 #define ASC_TXBUF_MSK 0x01FF
143
144 /*---- Inline function definitions ---------------------------*/
145
to_asc_port(struct uart_port * port)146 static inline struct asc_port *to_asc_port(struct uart_port *port)
147 {
148 return container_of(port, struct asc_port, port);
149 }
150
asc_in(struct uart_port * port,u32 offset)151 static inline u32 asc_in(struct uart_port *port, u32 offset)
152 {
153 #ifdef readl_relaxed
154 return readl_relaxed(port->membase + offset);
155 #else
156 return readl(port->membase + offset);
157 #endif
158 }
159
asc_out(struct uart_port * port,u32 offset,u32 value)160 static inline void asc_out(struct uart_port *port, u32 offset, u32 value)
161 {
162 #ifdef writel_relaxed
163 writel_relaxed(value, port->membase + offset);
164 #else
165 writel(value, port->membase + offset);
166 #endif
167 }
168
169 /*
170 * Some simple utility functions to enable and disable interrupts.
171 * Note that these need to be called with interrupts disabled.
172 */
asc_disable_tx_interrupts(struct uart_port * port)173 static inline void asc_disable_tx_interrupts(struct uart_port *port)
174 {
175 u32 intenable = asc_in(port, ASC_INTEN) & ~ASC_INTEN_THE;
176 asc_out(port, ASC_INTEN, intenable);
177 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
178 }
179
asc_enable_tx_interrupts(struct uart_port * port)180 static inline void asc_enable_tx_interrupts(struct uart_port *port)
181 {
182 u32 intenable = asc_in(port, ASC_INTEN) | ASC_INTEN_THE;
183 asc_out(port, ASC_INTEN, intenable);
184 }
185
asc_disable_rx_interrupts(struct uart_port * port)186 static inline void asc_disable_rx_interrupts(struct uart_port *port)
187 {
188 u32 intenable = asc_in(port, ASC_INTEN) & ~ASC_INTEN_RBE;
189 asc_out(port, ASC_INTEN, intenable);
190 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
191 }
192
asc_enable_rx_interrupts(struct uart_port * port)193 static inline void asc_enable_rx_interrupts(struct uart_port *port)
194 {
195 u32 intenable = asc_in(port, ASC_INTEN) | ASC_INTEN_RBE;
196 asc_out(port, ASC_INTEN, intenable);
197 }
198
asc_txfifo_is_empty(struct uart_port * port)199 static inline u32 asc_txfifo_is_empty(struct uart_port *port)
200 {
201 return asc_in(port, ASC_STA) & ASC_STA_TE;
202 }
203
asc_txfifo_is_half_empty(struct uart_port * port)204 static inline u32 asc_txfifo_is_half_empty(struct uart_port *port)
205 {
206 return asc_in(port, ASC_STA) & ASC_STA_THE;
207 }
208
asc_port_name(struct uart_port * port)209 static inline const char *asc_port_name(struct uart_port *port)
210 {
211 return to_platform_device(port->dev)->name;
212 }
213
214 /*----------------------------------------------------------------------*/
215
216 /*
217 * This section contains code to support the use of the ASC as a
218 * generic serial port.
219 */
220
asc_hw_txroom(struct uart_port * port)221 static inline unsigned asc_hw_txroom(struct uart_port *port)
222 {
223 u32 status = asc_in(port, ASC_STA);
224
225 if (status & ASC_STA_THE)
226 return port->fifosize / 2;
227 else if (!(status & ASC_STA_TF))
228 return 1;
229
230 return 0;
231 }
232
233 /*
234 * Start transmitting chars.
235 * This is called from both interrupt and task level.
236 * Either way interrupts are disabled.
237 */
asc_transmit_chars(struct uart_port * port)238 static void asc_transmit_chars(struct uart_port *port)
239 {
240 u8 ch;
241
242 uart_port_tx_limited(port, ch, asc_hw_txroom(port),
243 true,
244 asc_out(port, ASC_TXBUF, ch),
245 ({}));
246 }
247
asc_receive_chars(struct uart_port * port)248 static void asc_receive_chars(struct uart_port *port)
249 {
250 struct tty_port *tport = &port->state->port;
251 unsigned long status, mode;
252 unsigned long c = 0;
253 u8 flag;
254 bool ignore_pe = false;
255
256 /*
257 * Datasheet states: If the MODE field selects an 8-bit frame then
258 * this [parity error] bit is undefined. Software should ignore this
259 * bit when reading 8-bit frames.
260 */
261 mode = asc_in(port, ASC_CTL) & ASC_CTL_MODE_MSK;
262 if (mode == ASC_CTL_MODE_8BIT || mode == ASC_CTL_MODE_8BIT_PAR)
263 ignore_pe = true;
264
265 if (irqd_is_wakeup_set(irq_get_irq_data(port->irq)))
266 pm_wakeup_event(tport->tty->dev, 0);
267
268 while ((status = asc_in(port, ASC_STA)) & ASC_STA_RBF) {
269 c = asc_in(port, ASC_RXBUF) | ASC_RXBUF_DUMMY_RX;
270 flag = TTY_NORMAL;
271 port->icount.rx++;
272
273 if (status & ASC_STA_OE || c & ASC_RXBUF_FE ||
274 (c & ASC_RXBUF_PE && !ignore_pe)) {
275
276 if (c & ASC_RXBUF_FE) {
277 if (c == (ASC_RXBUF_FE | ASC_RXBUF_DUMMY_RX)) {
278 port->icount.brk++;
279 if (uart_handle_break(port))
280 continue;
281 c |= ASC_RXBUF_DUMMY_BE;
282 } else {
283 port->icount.frame++;
284 }
285 } else if (c & ASC_RXBUF_PE) {
286 port->icount.parity++;
287 }
288 /*
289 * Reading any data from the RX FIFO clears the
290 * overflow error condition.
291 */
292 if (status & ASC_STA_OE) {
293 port->icount.overrun++;
294 c |= ASC_RXBUF_DUMMY_OE;
295 }
296
297 c &= port->read_status_mask;
298
299 if (c & ASC_RXBUF_DUMMY_BE)
300 flag = TTY_BREAK;
301 else if (c & ASC_RXBUF_PE)
302 flag = TTY_PARITY;
303 else if (c & ASC_RXBUF_FE)
304 flag = TTY_FRAME;
305 }
306
307 if (uart_handle_sysrq_char(port, c & 0xff))
308 continue;
309
310 uart_insert_char(port, c, ASC_RXBUF_DUMMY_OE, c & 0xff, flag);
311 }
312
313 /* Tell the rest of the system the news. New characters! */
314 tty_flip_buffer_push(tport);
315 }
316
asc_interrupt(int irq,void * ptr)317 static irqreturn_t asc_interrupt(int irq, void *ptr)
318 {
319 struct uart_port *port = ptr;
320 u32 status;
321
322 uart_port_lock(port);
323
324 status = asc_in(port, ASC_STA);
325
326 if (status & ASC_STA_RBF) {
327 /* Receive FIFO not empty */
328 asc_receive_chars(port);
329 }
330
331 if ((status & ASC_STA_THE) &&
332 (asc_in(port, ASC_INTEN) & ASC_INTEN_THE)) {
333 /* Transmitter FIFO at least half empty */
334 asc_transmit_chars(port);
335 }
336
337 uart_port_unlock(port);
338
339 return IRQ_HANDLED;
340 }
341
342 /*----------------------------------------------------------------------*/
343
344 /*
345 * UART Functions
346 */
347
asc_tx_empty(struct uart_port * port)348 static unsigned int asc_tx_empty(struct uart_port *port)
349 {
350 return asc_txfifo_is_empty(port) ? TIOCSER_TEMT : 0;
351 }
352
asc_set_mctrl(struct uart_port * port,unsigned int mctrl)353 static void asc_set_mctrl(struct uart_port *port, unsigned int mctrl)
354 {
355 struct asc_port *ascport = to_asc_port(port);
356
357 /*
358 * This routine is used for seting signals of: DTR, DCD, CTS and RTS.
359 * We use ASC's hardware for CTS/RTS when hardware flow-control is
360 * enabled, however if the RTS line is required for another purpose,
361 * commonly controlled using HUP from userspace, then we need to toggle
362 * it manually, using GPIO.
363 *
364 * Some boards also have DTR and DCD implemented using PIO pins, code to
365 * do this should be hooked in here.
366 */
367
368 if (!ascport->rts)
369 return;
370
371 /* If HW flow-control is enabled, we can't fiddle with the RTS line */
372 if (asc_in(port, ASC_CTL) & ASC_CTL_CTSENABLE)
373 return;
374
375 gpiod_set_value(ascport->rts, mctrl & TIOCM_RTS);
376 }
377
asc_get_mctrl(struct uart_port * port)378 static unsigned int asc_get_mctrl(struct uart_port *port)
379 {
380 /*
381 * This routine is used for geting signals of: DTR, DCD, DSR, RI,
382 * and CTS/RTS
383 */
384 return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
385 }
386
387 /* There are probably characters waiting to be transmitted. */
asc_start_tx(struct uart_port * port)388 static void asc_start_tx(struct uart_port *port)
389 {
390 struct tty_port *tport = &port->state->port;
391
392 if (!kfifo_is_empty(&tport->xmit_fifo))
393 asc_enable_tx_interrupts(port);
394 }
395
396 /* Transmit stop */
asc_stop_tx(struct uart_port * port)397 static void asc_stop_tx(struct uart_port *port)
398 {
399 asc_disable_tx_interrupts(port);
400 }
401
402 /* Receive stop */
asc_stop_rx(struct uart_port * port)403 static void asc_stop_rx(struct uart_port *port)
404 {
405 asc_disable_rx_interrupts(port);
406 }
407
408 /* Handle breaks - ignored by us */
asc_break_ctl(struct uart_port * port,int break_state)409 static void asc_break_ctl(struct uart_port *port, int break_state)
410 {
411 /* Nothing here yet .. */
412 }
413
414 /*
415 * Enable port for reception.
416 */
asc_startup(struct uart_port * port)417 static int asc_startup(struct uart_port *port)
418 {
419 if (request_irq(port->irq, asc_interrupt, 0,
420 asc_port_name(port), port)) {
421 dev_err(port->dev, "cannot allocate irq.\n");
422 return -ENODEV;
423 }
424
425 asc_transmit_chars(port);
426 asc_enable_rx_interrupts(port);
427
428 return 0;
429 }
430
asc_shutdown(struct uart_port * port)431 static void asc_shutdown(struct uart_port *port)
432 {
433 asc_disable_tx_interrupts(port);
434 asc_disable_rx_interrupts(port);
435 free_irq(port->irq, port);
436 }
437
asc_pm(struct uart_port * port,unsigned int state,unsigned int oldstate)438 static void asc_pm(struct uart_port *port, unsigned int state,
439 unsigned int oldstate)
440 {
441 struct asc_port *ascport = to_asc_port(port);
442 unsigned long flags;
443 u32 ctl;
444
445 switch (state) {
446 case UART_PM_STATE_ON:
447 clk_prepare_enable(ascport->clk);
448 break;
449 case UART_PM_STATE_OFF:
450 /*
451 * Disable the ASC baud rate generator, which is as close as
452 * we can come to turning it off. Note this is not called with
453 * the port spinlock held.
454 */
455 uart_port_lock_irqsave(port, &flags);
456 ctl = asc_in(port, ASC_CTL) & ~ASC_CTL_RUN;
457 asc_out(port, ASC_CTL, ctl);
458 uart_port_unlock_irqrestore(port, flags);
459 clk_disable_unprepare(ascport->clk);
460 break;
461 }
462 }
463
asc_set_termios(struct uart_port * port,struct ktermios * termios,const struct ktermios * old)464 static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
465 const struct ktermios *old)
466 {
467 struct asc_port *ascport = to_asc_port(port);
468 bool manual_rts, toggle_rts = false;
469 struct gpio_desc *gpiod;
470 unsigned int baud;
471 u32 ctrl_val;
472 tcflag_t cflag;
473 unsigned long flags;
474
475 /* Update termios to reflect hardware capabilities */
476 termios->c_cflag &= ~(CMSPAR |
477 (ascport->hw_flow_control ? 0 : CRTSCTS));
478
479 port->uartclk = clk_get_rate(ascport->clk);
480
481 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
482 cflag = termios->c_cflag;
483
484 uart_port_lock_irqsave(port, &flags);
485
486 /* read control register */
487 ctrl_val = asc_in(port, ASC_CTL);
488
489 /* stop serial port and reset value */
490 asc_out(port, ASC_CTL, (ctrl_val & ~ASC_CTL_RUN));
491 ctrl_val = ASC_CTL_RXENABLE | ASC_CTL_FIFOENABLE;
492
493 /* reset fifo rx & tx */
494 asc_out(port, ASC_TXRESET, 1);
495 asc_out(port, ASC_RXRESET, 1);
496
497 /* set character length */
498 if ((cflag & CSIZE) == CS7) {
499 ctrl_val |= ASC_CTL_MODE_7BIT_PAR;
500 cflag |= PARENB;
501 } else {
502 ctrl_val |= (cflag & PARENB) ? ASC_CTL_MODE_8BIT_PAR :
503 ASC_CTL_MODE_8BIT;
504 cflag &= ~CSIZE;
505 cflag |= CS8;
506 }
507 termios->c_cflag = cflag;
508
509 /* set stop bit */
510 ctrl_val |= (cflag & CSTOPB) ? ASC_CTL_STOP_2BIT : ASC_CTL_STOP_1BIT;
511
512 /* odd parity */
513 if (cflag & PARODD)
514 ctrl_val |= ASC_CTL_PARITYODD;
515
516 /* hardware flow control */
517 if ((cflag & CRTSCTS)) {
518 ctrl_val |= ASC_CTL_CTSENABLE;
519
520 /* If flow-control selected, stop handling RTS manually */
521 if (ascport->rts) {
522 toggle_rts = true;
523 manual_rts = false;
524 }
525 } else {
526 /* If flow-control disabled, it's safe to handle RTS manually */
527 if (!ascport->rts && ascport->states[NO_HW_FLOWCTRL])
528 manual_rts = toggle_rts = true;
529 }
530
531 if ((baud < 19200) && !ascport->force_m1) {
532 asc_out(port, ASC_BAUDRATE, (port->uartclk / (16 * baud)));
533 } else {
534 /*
535 * MODE 1: recommended for high bit rates (above 19.2K)
536 *
537 * baudrate * 16 * 2^16
538 * ASCBaudRate = ------------------------
539 * inputclock
540 *
541 * To keep maths inside 64bits, we divide inputclock by 16.
542 */
543 u64 dividend = (u64)baud * (1 << 16);
544
545 do_div(dividend, port->uartclk / 16);
546 asc_out(port, ASC_BAUDRATE, dividend);
547 ctrl_val |= ASC_CTL_BAUDMODE;
548 }
549
550 uart_update_timeout(port, cflag, baud);
551
552 ascport->port.read_status_mask = ASC_RXBUF_DUMMY_OE;
553 if (termios->c_iflag & INPCK)
554 ascport->port.read_status_mask |= ASC_RXBUF_FE | ASC_RXBUF_PE;
555 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
556 ascport->port.read_status_mask |= ASC_RXBUF_DUMMY_BE;
557
558 /*
559 * Characters to ignore
560 */
561 ascport->port.ignore_status_mask = 0;
562 if (termios->c_iflag & IGNPAR)
563 ascport->port.ignore_status_mask |= ASC_RXBUF_FE | ASC_RXBUF_PE;
564 if (termios->c_iflag & IGNBRK) {
565 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_BE;
566 /*
567 * If we're ignoring parity and break indicators,
568 * ignore overruns too (for real raw support).
569 */
570 if (termios->c_iflag & IGNPAR)
571 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_OE;
572 }
573
574 /*
575 * Ignore all characters if CREAD is not set.
576 */
577 if (!(termios->c_cflag & CREAD))
578 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_RX;
579
580 /* Set the timeout */
581 asc_out(port, ASC_TIMEOUT, 20);
582
583 /* write final value and enable port */
584 asc_out(port, ASC_CTL, (ctrl_val | ASC_CTL_RUN));
585
586 uart_port_unlock_irqrestore(port, flags);
587
588 if (toggle_rts) {
589 if (manual_rts) {
590 pinctrl_select_state(ascport->pinctrl,
591 ascport->states[NO_HW_FLOWCTRL]);
592
593 gpiod = devm_gpiod_get(port->dev, "rts", GPIOD_OUT_LOW);
594 if (!IS_ERR(gpiod)) {
595 gpiod_set_consumer_name(gpiod,
596 port->dev->of_node->name);
597 ascport->rts = gpiod;
598 }
599 } else {
600 devm_gpiod_put(port->dev, ascport->rts);
601 ascport->rts = NULL;
602 pinctrl_select_state(ascport->pinctrl,
603 ascport->states[DEFAULT]);
604 }
605 }
606 }
607
asc_type(struct uart_port * port)608 static const char *asc_type(struct uart_port *port)
609 {
610 return (port->type == PORT_ASC) ? DRIVER_NAME : NULL;
611 }
612
asc_release_port(struct uart_port * port)613 static void asc_release_port(struct uart_port *port)
614 {
615 }
616
asc_request_port(struct uart_port * port)617 static int asc_request_port(struct uart_port *port)
618 {
619 return 0;
620 }
621
622 /*
623 * Called when the port is opened, and UPF_BOOT_AUTOCONF flag is set
624 * Set type field if successful
625 */
asc_config_port(struct uart_port * port,int flags)626 static void asc_config_port(struct uart_port *port, int flags)
627 {
628 if ((flags & UART_CONFIG_TYPE))
629 port->type = PORT_ASC;
630 }
631
632 static int
asc_verify_port(struct uart_port * port,struct serial_struct * ser)633 asc_verify_port(struct uart_port *port, struct serial_struct *ser)
634 {
635 /* No user changeable parameters */
636 return -EINVAL;
637 }
638
639 #ifdef CONFIG_CONSOLE_POLL
640 /*
641 * Console polling routines for writing and reading from the uart while
642 * in an interrupt or debug context (i.e. kgdb).
643 */
644
asc_get_poll_char(struct uart_port * port)645 static int asc_get_poll_char(struct uart_port *port)
646 {
647 if (!(asc_in(port, ASC_STA) & ASC_STA_RBF))
648 return NO_POLL_CHAR;
649
650 return asc_in(port, ASC_RXBUF);
651 }
652
asc_put_poll_char(struct uart_port * port,unsigned char c)653 static void asc_put_poll_char(struct uart_port *port, unsigned char c)
654 {
655 while (!asc_txfifo_is_half_empty(port))
656 cpu_relax();
657 asc_out(port, ASC_TXBUF, c);
658 }
659
660 #endif /* CONFIG_CONSOLE_POLL */
661
662 /*---------------------------------------------------------------------*/
663
664 static const struct uart_ops asc_uart_ops = {
665 .tx_empty = asc_tx_empty,
666 .set_mctrl = asc_set_mctrl,
667 .get_mctrl = asc_get_mctrl,
668 .start_tx = asc_start_tx,
669 .stop_tx = asc_stop_tx,
670 .stop_rx = asc_stop_rx,
671 .break_ctl = asc_break_ctl,
672 .startup = asc_startup,
673 .shutdown = asc_shutdown,
674 .set_termios = asc_set_termios,
675 .type = asc_type,
676 .release_port = asc_release_port,
677 .request_port = asc_request_port,
678 .config_port = asc_config_port,
679 .verify_port = asc_verify_port,
680 .pm = asc_pm,
681 #ifdef CONFIG_CONSOLE_POLL
682 .poll_get_char = asc_get_poll_char,
683 .poll_put_char = asc_put_poll_char,
684 #endif /* CONFIG_CONSOLE_POLL */
685 };
686
asc_init_port(struct asc_port * ascport,struct platform_device * pdev)687 static int asc_init_port(struct asc_port *ascport,
688 struct platform_device *pdev)
689 {
690 struct uart_port *port = &ascport->port;
691 struct resource *res;
692 int ret;
693
694 port->iotype = UPIO_MEM;
695 port->flags = UPF_BOOT_AUTOCONF;
696 port->ops = &asc_uart_ops;
697 port->fifosize = ASC_FIFO_SIZE;
698 port->dev = &pdev->dev;
699 port->irq = platform_get_irq(pdev, 0);
700 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_ST_ASC_CONSOLE);
701
702 port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
703 if (IS_ERR(port->membase))
704 return PTR_ERR(port->membase);
705 port->mapbase = res->start;
706
707 spin_lock_init(&port->lock);
708
709 ascport->clk = devm_clk_get(&pdev->dev, NULL);
710
711 if (WARN_ON(IS_ERR(ascport->clk)))
712 return -EINVAL;
713 /* ensure that clk rate is correct by enabling the clk */
714 ret = clk_prepare_enable(ascport->clk);
715 if (ret)
716 return ret;
717 ascport->port.uartclk = clk_get_rate(ascport->clk);
718 WARN_ON(ascport->port.uartclk == 0);
719 clk_disable_unprepare(ascport->clk);
720
721 ascport->pinctrl = devm_pinctrl_get(&pdev->dev);
722 if (IS_ERR(ascport->pinctrl)) {
723 ret = PTR_ERR(ascport->pinctrl);
724 dev_err(&pdev->dev, "Failed to get Pinctrl: %d\n", ret);
725 return ret;
726 }
727
728 ascport->states[DEFAULT] =
729 pinctrl_lookup_state(ascport->pinctrl, "default");
730 if (IS_ERR(ascport->states[DEFAULT])) {
731 ret = PTR_ERR(ascport->states[DEFAULT]);
732 dev_err(&pdev->dev,
733 "Failed to look up Pinctrl state 'default': %d\n", ret);
734 return ret;
735 }
736
737 /* "no-hw-flowctrl" state is optional */
738 ascport->states[NO_HW_FLOWCTRL] =
739 pinctrl_lookup_state(ascport->pinctrl, "no-hw-flowctrl");
740 if (IS_ERR(ascport->states[NO_HW_FLOWCTRL]))
741 ascport->states[NO_HW_FLOWCTRL] = NULL;
742
743 return 0;
744 }
745
asc_of_get_asc_port(struct platform_device * pdev)746 static struct asc_port *asc_of_get_asc_port(struct platform_device *pdev)
747 {
748 struct device_node *np = pdev->dev.of_node;
749 int id;
750
751 if (!np)
752 return NULL;
753
754 id = of_alias_get_id(np, "serial");
755 if (id < 0)
756 id = of_alias_get_id(np, ASC_SERIAL_NAME);
757
758 if (id < 0)
759 id = 0;
760
761 if (WARN_ON(id >= ASC_MAX_PORTS))
762 return NULL;
763
764 asc_ports[id].hw_flow_control = of_property_read_bool(np,
765 "uart-has-rtscts");
766 asc_ports[id].force_m1 = of_property_read_bool(np, "st,force-m1");
767 asc_ports[id].port.line = id;
768 asc_ports[id].rts = NULL;
769
770 return &asc_ports[id];
771 }
772
773 #ifdef CONFIG_OF
774 static const struct of_device_id asc_match[] = {
775 { .compatible = "st,asc", },
776 {},
777 };
778
779 MODULE_DEVICE_TABLE(of, asc_match);
780 #endif
781
asc_serial_probe(struct platform_device * pdev)782 static int asc_serial_probe(struct platform_device *pdev)
783 {
784 int ret;
785 struct asc_port *ascport;
786
787 ascport = asc_of_get_asc_port(pdev);
788 if (!ascport)
789 return -ENODEV;
790
791 ret = asc_init_port(ascport, pdev);
792 if (ret)
793 return ret;
794
795 ret = uart_add_one_port(&asc_uart_driver, &ascport->port);
796 if (ret)
797 return ret;
798
799 platform_set_drvdata(pdev, &ascport->port);
800
801 return 0;
802 }
803
asc_serial_remove(struct platform_device * pdev)804 static void asc_serial_remove(struct platform_device *pdev)
805 {
806 struct uart_port *port = platform_get_drvdata(pdev);
807
808 uart_remove_one_port(&asc_uart_driver, port);
809 }
810
asc_serial_suspend(struct device * dev)811 static int asc_serial_suspend(struct device *dev)
812 {
813 struct uart_port *port = dev_get_drvdata(dev);
814
815 return uart_suspend_port(&asc_uart_driver, port);
816 }
817
asc_serial_resume(struct device * dev)818 static int asc_serial_resume(struct device *dev)
819 {
820 struct uart_port *port = dev_get_drvdata(dev);
821
822 return uart_resume_port(&asc_uart_driver, port);
823 }
824
825 /*----------------------------------------------------------------------*/
826
827 #ifdef CONFIG_SERIAL_ST_ASC_CONSOLE
asc_console_putchar(struct uart_port * port,unsigned char ch)828 static void asc_console_putchar(struct uart_port *port, unsigned char ch)
829 {
830 unsigned int timeout = 1000000;
831
832 /* Wait for upto 1 second in case flow control is stopping us. */
833 while (--timeout && !asc_txfifo_is_half_empty(port))
834 udelay(1);
835
836 asc_out(port, ASC_TXBUF, ch);
837 }
838
839 /*
840 * Print a string to the serial port trying not to disturb
841 * any possible real use of the port...
842 */
843
asc_console_write(struct console * co,const char * s,unsigned count)844 static void asc_console_write(struct console *co, const char *s, unsigned count)
845 {
846 struct uart_port *port = &asc_ports[co->index].port;
847 unsigned long flags;
848 unsigned long timeout = 1000000;
849 int locked = 1;
850 u32 intenable;
851
852 if (port->sysrq)
853 locked = 0; /* asc_interrupt has already claimed the lock */
854 else if (oops_in_progress)
855 locked = uart_port_trylock_irqsave(port, &flags);
856 else
857 uart_port_lock_irqsave(port, &flags);
858
859 /*
860 * Disable interrupts so we don't get the IRQ line bouncing
861 * up and down while interrupts are disabled.
862 */
863 intenable = asc_in(port, ASC_INTEN);
864 asc_out(port, ASC_INTEN, 0);
865 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
866
867 uart_console_write(port, s, count, asc_console_putchar);
868
869 while (--timeout && !asc_txfifo_is_empty(port))
870 udelay(1);
871
872 asc_out(port, ASC_INTEN, intenable);
873
874 if (locked)
875 uart_port_unlock_irqrestore(port, flags);
876 }
877
asc_console_setup(struct console * co,char * options)878 static int asc_console_setup(struct console *co, char *options)
879 {
880 struct asc_port *ascport;
881 int baud = 115200;
882 int bits = 8;
883 int parity = 'n';
884 int flow = 'n';
885
886 if (co->index >= ASC_MAX_PORTS)
887 return -ENODEV;
888
889 ascport = &asc_ports[co->index];
890
891 /*
892 * This driver does not support early console initialization
893 * (use ARM early printk support instead), so we only expect
894 * this to be called during the uart port registration when the
895 * driver gets probed and the port should be mapped at that point.
896 */
897 if (ascport->port.mapbase == 0 || ascport->port.membase == NULL)
898 return -ENXIO;
899
900 if (options)
901 uart_parse_options(options, &baud, &parity, &bits, &flow);
902
903 return uart_set_options(&ascport->port, co, baud, parity, bits, flow);
904 }
905
906 static struct console asc_console = {
907 .name = ASC_SERIAL_NAME,
908 .device = uart_console_device,
909 .write = asc_console_write,
910 .setup = asc_console_setup,
911 .flags = CON_PRINTBUFFER,
912 .index = -1,
913 .data = &asc_uart_driver,
914 };
915
916 #define ASC_SERIAL_CONSOLE (&asc_console)
917
918 #else
919 #define ASC_SERIAL_CONSOLE NULL
920 #endif /* CONFIG_SERIAL_ST_ASC_CONSOLE */
921
922 static struct uart_driver asc_uart_driver = {
923 .owner = THIS_MODULE,
924 .driver_name = DRIVER_NAME,
925 .dev_name = ASC_SERIAL_NAME,
926 .major = 0,
927 .minor = 0,
928 .nr = ASC_MAX_PORTS,
929 .cons = ASC_SERIAL_CONSOLE,
930 };
931
932 static DEFINE_SIMPLE_DEV_PM_OPS(asc_serial_pm_ops, asc_serial_suspend,
933 asc_serial_resume);
934
935 static struct platform_driver asc_serial_driver = {
936 .probe = asc_serial_probe,
937 .remove_new = asc_serial_remove,
938 .driver = {
939 .name = DRIVER_NAME,
940 .pm = pm_sleep_ptr(&asc_serial_pm_ops),
941 .of_match_table = of_match_ptr(asc_match),
942 },
943 };
944
asc_init(void)945 static int __init asc_init(void)
946 {
947 int ret;
948 static const char banner[] __initconst =
949 KERN_INFO "STMicroelectronics ASC driver initialized\n";
950
951 printk(banner);
952
953 ret = uart_register_driver(&asc_uart_driver);
954 if (ret)
955 return ret;
956
957 ret = platform_driver_register(&asc_serial_driver);
958 if (ret)
959 uart_unregister_driver(&asc_uart_driver);
960
961 return ret;
962 }
963
asc_exit(void)964 static void __exit asc_exit(void)
965 {
966 platform_driver_unregister(&asc_serial_driver);
967 uart_unregister_driver(&asc_uart_driver);
968 }
969
970 module_init(asc_init);
971 module_exit(asc_exit);
972
973 MODULE_ALIAS("platform:" DRIVER_NAME);
974 MODULE_AUTHOR("STMicroelectronics (R&D) Limited");
975 MODULE_DESCRIPTION("STMicroelectronics ASC serial port driver");
976 MODULE_LICENSE("GPL");
977