Searched full:vid0 (Results 1 – 11 of 11) sorted by relevance
| /linux-6.12.1/drivers/regulator/ |
| D | max8952.c | 40 bool vid0; member
76 if (max8952->vid0) in max8952_get_voltage_sel()
94 max8952->vid0 = selector & 0x1; in max8952_set_voltage_sel()
96 gpiod_set_value(max8952->vid0_gpiod, max8952->vid0); in max8952_set_voltage_sel()
234 max8952->vid0 = pdata->default_mode & 0x1; in max8952_pmic_probe()
237 /* Fetch vid0 and vid1 GPIOs if available */ in max8952_pmic_probe()
238 gflags = max8952->vid0 ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW; in max8952_pmic_probe()
253 dev_warn(&client->dev, "VID0/1 gpio invalid: " in max8952_pmic_probe()
255 max8952->vid0 = 0; in max8952_pmic_probe()
266 dev_err(&client->dev, "DVS modes disabled because VID0 and VID1" in max8952_pmic_probe()
[all …]
|
| D | max8649.c | 52 unsigned mode:2; /* bit[1:0] = VID1, VID0 */
199 /* enable VID0 & VID1 */ in max8649_regulator_probe()
|
| /linux-6.12.1/include/linux/regulator/ |
| D | max8649.h | 34 unsigned mode:2; /* bit[1:0] = VID1,VID0 */
|
| /linux-6.12.1/Documentation/devicetree/bindings/display/xlnx/ |
| D | xlnx,zynqmp-dpsub.yaml | 105 - const: vid0
197 dma-names = "vid0", "vid1", "vid2", "gfx0";
|
| /linux-6.12.1/drivers/gpu/drm/sti/ |
| D | sti_mixer.c | 84 char *const disp_layer[] = {"BKG", "VID0", "VID1", "GDP0", in mixer_dbg_ctl()
113 seq_puts(s, "VID0"); in mixer_dbg_crb()
|
| /linux-6.12.1/Documentation/hwmon/ |
| D | w83627hf.rst | 55 The `w83627_HF_` uses pins 110-106 as VID0-VID4. The `w83627_THF_` uses the
|
| /linux-6.12.1/drivers/media/pci/dt3155/ |
| D | dt3155.c | 359 strscpy(input->name, "J2/VID0", sizeof(input->name)); in dt3155_enum_input()
|
| /linux-6.12.1/drivers/net/ethernet/freescale/ |
| D | ucc_geth.h | 964 = 0x2, /* Tagged - if vid0 replace vid with default value */
|
| /linux-6.12.1/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp.dtsi | 1210 dma-names = "vid0", "vid1", "vid2", "gfx0";
|
| /linux-6.12.1/drivers/net/dsa/mv88e6xxx/ |
| D | chip.c | 2605 struct mv88e6xxx_vtu_entry vid0 = { in mv88e6xxx_port_broadcast_sync() local
2611 err = mv88e6xxx_port_broadcast_sync_vlan(chip, &vid0, &ctx); in mv88e6xxx_port_broadcast_sync()
|
| /linux-6.12.1/drivers/platform/x86/ |
| D | thinkpad_acpi.c | 4682 "\\_SB.PCI0.AGP0.VID0", /* 600e/x, 770x */
4683 "\\_SB.PCI0.VID0", /* 770e */
|