Searched full:sdclk (Results 1 – 25 of 28) sorted by relevance
12
| /linux-6.12.1/Documentation/devicetree/bindings/mmc/ |
| D | cdns,sdhci.yaml | 92 cdns,phy-dll-delay-sdclk:
94 Value of the delay introduced on the sdclk output for all modes except
100 cdns,phy-dll-delay-sdclk-hsmmc:
102 Value of the delay introduced on the sdclk output for HS200, HS400 and
155 cdns,phy-dll-delay-sdclk = <0>;
|
| D | marvell,xenon-sdhci.yaml | 232 clocks = <&sdclk 0>, <&axi_clk 0>;
274 clocks = <&sdclk 0>;
|
| /linux-6.12.1/drivers/mmc/host/ |
| D | sdhci-xenon-phy.c | 238 * 1. SDCLK frequency changes.
239 * 2. SDCLK is stopped and re-enabled.
490 * 2. SDCLK is higher than 52MHz in xenon_emmc_phy_strobe_delay_adj()
512 * If eMMC PHY Slow Mode is required in lower speed mode (SDCLK < 55MHz)
805 * PHY setting should be adjusted when SDCLK frequency, Bus Width
|
| D | sdhci-of-aspeed.c | 261 * period of SDCLK = period of SDMCLK. in aspeed_sdhci_set_clock()
264 * period of SDCLK = period of SDMCLK * 2 * (EMMC12C[7:6], EMMC[15:8]) in aspeed_sdhci_set_clock()
544 dev_err(&pdev->dev, "Unable to enable SDCLK\n"); in aspeed_sdc_probe()
|
| D | sdhci-cadence.c | 98 { "cdns,phy-dll-delay-sdclk", SDHCI_CDNS_PHY_DLY_SDCLK, },
99 { "cdns,phy-dll-delay-sdclk-hsmmc", SDHCI_CDNS_PHY_DLY_HSMMC, },
|
| D | sdhci-xenon.c | 53 /* Set SDCLK-off-while-idle */
491 /* Disable SDCLK-Off-While-Idle before card init */ in xenon_sdhc_prepare()
|
| D | uniphier-sd.c | 25 #define UNIPHIER_SD_CLKCTL_OFFEN BIT(9) // auto SDCLK stop
|
| D | sdhci-s3c.c | 629 /* HSMMC on Samsung SoCs uses SDCLK as timeout clock */ in sdhci_s3c_probe()
|
| D | sdhci-tegra.c | 1725 * timeout clock and SW can choose TMCLK or SDCLK for hardware in sdhci_tegra_probe()
1732 * be achieved is 11s better than using SDCLK for data timeout. in sdhci_tegra_probe()
|
| D | sdhci.h | 428 /* Controller uses SDCLK instead of TMCLK for data timeouts */
|
| /linux-6.12.1/drivers/cpufreq/ |
| D | sa1110-cpufreq.c | 152 * If SDCLK would invalidate the SDRAM timings, in sdram_calculate_timing()
153 * run SDCLK at half speed. in sdram_calculate_timing()
|
| /linux-6.12.1/arch/arm64/boot/dts/socionext/ |
| D | uniphier-ld11.dtsi | 464 cdns,phy-dll-delay-sdclk = <21>;
465 cdns,phy-dll-delay-sdclk-hsmmc = <21>;
|
| D | uniphier-ld20.dtsi | 602 cdns,phy-dll-delay-sdclk = <21>;
603 cdns,phy-dll-delay-sdclk-hsmmc = <21>;
|
| D | uniphier-pxs3.dtsi | 422 cdns,phy-dll-delay-sdclk = <21>;
423 cdns,phy-dll-delay-sdclk-hsmmc = <21>;
|
| /linux-6.12.1/drivers/pinctrl/uniphier/ |
| D | pinctrl-uniphier-nx1.c | 18 UNIPHIER_PINCTRL_PIN(1, "SDCLK", UNIPHIER_PIN_IECTRL_EXIST,
|
| D | pinctrl-uniphier-sld8.c | 111 UNIPHIER_PINCTRL_PIN(32, "SDCLK", 8,
|
| D | pinctrl-uniphier-ld4.c | 147 UNIPHIER_PINCTRL_PIN(44, "SDCLK", UNIPHIER_PIN_IECTRL_NONE,
|
| D | pinctrl-uniphier-ld6b.c | 156 UNIPHIER_PINCTRL_PIN(47, "SDCLK", UNIPHIER_PIN_IECTRL_NONE,
|
| D | pinctrl-uniphier-pro5.c | 765 UNIPHIER_PINCTRL_PIN(250, "SDCLK", UNIPHIER_PIN_IECTRL_NONE,
|
| D | pinctrl-uniphier-pxs2.c | 156 UNIPHIER_PINCTRL_PIN(47, "SDCLK", UNIPHIER_PIN_IECTRL_NONE,
|
| D | pinctrl-uniphier-pxs3.c | 144 UNIPHIER_PINCTRL_PIN(43, "SDCLK", UNIPHIER_PIN_IECTRL_EXIST,
|
| /linux-6.12.1/drivers/pinctrl/ |
| D | pinctrl-ep93xx.c | 129 PINCTRL_PIN(10, "SDCLK"),
437 PINCTRL_PIN(53, "SDCLK"), /* D3 */
858 PINCTRL_PIN(117, "SDCLK"), /* G4 */
|
| /linux-6.12.1/drivers/clk/ |
| D | clk-aspeed.c | 71 [ASPEED_CLK_GATE_SDCLK] = { 27, 16, "sdclk-gate", NULL, 0 }, /* SDIO/SD */
|
| D | clk-ast2600.c | 135 [ASPEED_CLK_GATE_SDCLK] = { 36, 56, "sdclk-gate", NULL, 0 }, /* SDIO/SD */
|
| /linux-6.12.1/include/linux/mmc/ |
| D | host.h | 145 * switching might fail because the SDCLK is not really quiet.
|
12