| /linux-6.12.1/Documentation/devicetree/bindings/leds/ |
| D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| /linux-6.12.1/Documentation/devicetree/bindings/mfd/ |
| D | adi,adp5585.yaml | 22 - adi,adp5585-02 # No pull-up resistors by default on special pins
24 - adi,adp5585-04 # Pull-down resistors on all pins by default
|
| /linux-6.12.1/drivers/rtc/ |
| D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
| /linux-6.12.1/Documentation/hwmon/ |
| D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| D | ltc2991.rst | 30 resistors or temperature sensing transistors. Additional measurements include
|
| D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| /linux-6.12.1/drivers/mfd/ |
| D | adp5585.c | 36 * resistors, and therefore have different default register values:
40 * - The -02 variant has no default pull-up or pull-down resistors.
41 * - The -04 variant has default pull-down resistors on all GPIO pins.
|
| /linux-6.12.1/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /linux-6.12.1/Documentation/devicetree/bindings/hwmon/ |
| D | ntc-thermistor.yaml | 12 Thermistors with negative temperature coefficient (NTC) are resistors that
59 We can use both pull-up and pull-down resistors at the same time, and then
|
| D | adi,ltc2991.yaml | 17 sense resistors or temperature sensing transistors.
|
| /linux-6.12.1/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /linux-6.12.1/drivers/input/serio/ |
| D | parkbd.c | 33 * The diodes can be fairly any type, and the resistors should be somewhere
34 * around 5 kOhm, but the adapter will likely work without the resistors,
|
| /linux-6.12.1/Documentation/devicetree/bindings/pinctrl/ |
| D | mediatek,mt6779-pinctrl.yaml | 162 Pull up settings for 2 pull resistors, R0 and R1. User can
174 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt6795-pinctrl.yaml | 133 Pull up settings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt8183-pinctrl.yaml | 146 Pull up settings for 2 pull resistors, R0 and R1. User can
158 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt8365-pinctrl.yaml | 152 Pull up settings for 2 pull resistors, R0 and R1. User can
166 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/ |
| D | motorcomm,yt8xxx.yaml | 59 be configured with hardware pull-up resistors to match the SOC voltage
76 be configured with hardware pull-up resistors to match the SOC voltage
|
| /linux-6.12.1/include/linux/platform_data/ |
| D | st_sensors_pdata.h | 21 * @pullups: enable/disable i2c controller pullup resistors.
|
| /linux-6.12.1/include/linux/usb/ |
| D | isp116x.h | 11 /* Enable internal resistors on downstream ports */
|
| D | isp1362.h | 11 /* Enable internal pulldown resistors on downstream ports */
|
| /linux-6.12.1/Documentation/devicetree/bindings/gpio/ |
| D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
| /linux-6.12.1/arch/sh/drivers/pci/ |
| D | fixups-sdk7786.c | 21 * resistors to determine card presence. Hotplug remains unsupported.
|
| /linux-6.12.1/Documentation/devicetree/bindings/power/supply/ |
| D | richtek,rt9467.yaml | 18 integrated sensing resistors.
|