| /linux-6.12.1/drivers/net/ethernet/qualcomm/ |
| D | qca_spi.c | 70 start_spi_intr_handling(struct qcaspi *qca, u16 *intr_cause) in start_spi_intr_handling() argument
74 qcaspi_write_register(qca, SPI_REG_INTR_ENABLE, 0, wr_verify); in start_spi_intr_handling()
75 qcaspi_read_register(qca, SPI_REG_INTR_CAUSE, intr_cause); in start_spi_intr_handling()
76 netdev_dbg(qca->net_dev, "interrupts: 0x%04x\n", *intr_cause); in start_spi_intr_handling()
80 end_spi_intr_handling(struct qcaspi *qca, u16 intr_cause) in end_spi_intr_handling() argument
87 qcaspi_write_register(qca, SPI_REG_INTR_CAUSE, intr_cause, 0); in end_spi_intr_handling()
88 qcaspi_write_register(qca, SPI_REG_INTR_ENABLE, intr_enable, wr_verify); in end_spi_intr_handling()
89 netdev_dbg(qca->net_dev, "acking int: 0x%04x\n", intr_cause); in end_spi_intr_handling()
93 qcaspi_write_burst(struct qcaspi *qca, u8 *src, u32 len) in qcaspi_write_burst() argument
111 ret = spi_sync(qca->spi_dev, &msg); in qcaspi_write_burst()
[all …]
|
| D | qca_uart.c | 51 struct qcauart *qca = serdev_device_get_drvdata(serdev); in qca_tty_receive() local
52 struct net_device *netdev = qca->net_dev; in qca_tty_receive()
56 if (!qca->rx_skb) { in qca_tty_receive()
57 qca->rx_skb = netdev_alloc_skb_ip_align(netdev, in qca_tty_receive()
60 if (!qca->rx_skb) { in qca_tty_receive()
70 retcode = qcafrm_fsm_decode(&qca->frm_handle, in qca_tty_receive()
71 qca->rx_skb->data, in qca_tty_receive()
72 skb_tailroom(qca->rx_skb), in qca_tty_receive()
92 skb_put(qca->rx_skb, retcode); in qca_tty_receive()
93 qca->rx_skb->protocol = eth_type_trans( in qca_tty_receive()
[all …]
|
| D | qca_debug.c | 62 struct qcaspi *qca = s->private; in qcaspi_info_show() local
65 (unsigned long)qca->buffer_size); in qcaspi_info_show()
69 if (qca->txr.skb[qca->txr.head] == NULL) in qcaspi_info_show()
71 else if (qca->txr.skb[qca->txr.tail]) in qcaspi_info_show()
79 qca->txr.size); in qcaspi_info_show()
82 (unsigned int)qca->sync); in qcaspi_info_show()
83 switch (qca->sync) { in qcaspi_info_show()
100 qca->spi_dev->irq); in qcaspi_info_show()
102 qca->intr); in qcaspi_info_show()
105 (unsigned long)qca->spi_dev->max_speed_hz); in qcaspi_info_show()
[all …]
|
| D | qca_7k.c | 18 qcaspi_spi_error(struct qcaspi *qca) in qcaspi_spi_error() argument
20 if (qca->sync != QCASPI_SYNC_READY) in qcaspi_spi_error()
23 netdev_err(qca->net_dev, "spi error\n"); in qcaspi_spi_error()
24 qca->sync = QCASPI_SYNC_UNKNOWN; in qcaspi_spi_error()
25 qca->stats.spi_err++; in qcaspi_spi_error()
29 qcaspi_read_register(struct qcaspi *qca, u16 reg, u16 *result) in qcaspi_read_register() argument
51 if (qca->legacy_mode) { in qcaspi_read_register()
52 spi_sync(qca->spi_dev, &msg); in qcaspi_read_register()
56 ret = spi_sync(qca->spi_dev, &msg); in qcaspi_read_register()
62 qcaspi_spi_error(qca); in qcaspi_read_register()
[all …]
|
| /linux-6.12.1/drivers/bluetooth/ |
| D | hci_qca.c | 196 * QCA Bluetooth chipset
211 * Platform data for the QCA Bluetooth power driver.
286 struct qca_data *qca = hu->priv; in serial_clock_vote() local
289 bool old_vote = (qca->tx_vote | qca->rx_vote); in serial_clock_vote()
294 diff = jiffies_to_msecs(jiffies - qca->vote_last_jif); in serial_clock_vote()
297 qca->vote_off_ms += diff; in serial_clock_vote()
299 qca->vote_on_ms += diff; in serial_clock_vote()
303 qca->tx_vote = true; in serial_clock_vote()
304 qca->tx_votes_on++; in serial_clock_vote()
308 qca->rx_vote = true; in serial_clock_vote()
[all …]
|
| D | btqca.c | 27 bt_dev_dbg(hdev, "QCA Version Request"); in qca_read_soc_version()
44 bt_dev_err(hdev, "Reading QCA version information failed (%d)", in qca_read_soc_version()
50 bt_dev_err(hdev, "QCA Version size mismatch len %d", skb->len); in qca_read_soc_version()
59 bt_dev_err(hdev, "QCA Wrong packet received %d %d", edl->cresp, in qca_read_soc_version()
70 bt_dev_info(hdev, "QCA Product ID :0x%08x", in qca_read_soc_version()
72 bt_dev_info(hdev, "QCA SOC Version :0x%08x", in qca_read_soc_version()
74 bt_dev_info(hdev, "QCA ROM Version :0x%08x", in qca_read_soc_version()
76 bt_dev_info(hdev, "QCA Patch Version:0x%08x", in qca_read_soc_version()
85 bt_dev_err(hdev, "QCA Failed to get version (%d)", err); in qca_read_soc_version()
99 bt_dev_dbg(hdev, "QCA read fw build info"); in qca_read_fw_build_info()
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/mips/ |
| D | ath79-soc.txt | 7 - qca,ar7130
8 - qca,ar7141
9 - qca,ar7161
10 - qca,ar7240
11 - qca,ar7241
12 - qca,ar7242
13 - qca,ar9130
14 - qca,ar9132
15 - qca,ar9330
16 - qca,ar9331
[all …]
|
| /linux-6.12.1/arch/mips/boot/dts/qca/ |
| D | ar9132.dtsi | 5 compatible = "qca,ar9132";
23 compatible = "qca,ar9132-cpu-intc", "qca,ar7100-cpu-intc";
28 qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
29 qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
52 compatible = "qca,ar9132-ddr-controller",
53 "qca,ar7240-ddr-controller";
56 #qca,ddr-wb-channel-cells = <1>;
75 compatible = "qca,ar9132-gpio",
76 "qca,ar7100-gpio";
90 compatible = "qca,ar9132-pll",
[all …]
|
| D | ar9331.dtsi | 5 compatible = "qca,ar9331";
23 compatible = "qca,ar7100-cpu-intc";
28 qca,ddr-wb-channel-interrupts = <2>, <3>;
29 qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>;
56 compatible = "qca,ar7240-ddr-controller";
59 #qca,ddr-wb-channel-cells = <1>;
63 compatible = "qca,ar9330-uart";
75 compatible = "qca,ar7100-gpio";
91 compatible = "qca,ar9330-pll";
101 compatible = "qca,ar7240-misc-intc";
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/interrupt-controller/ |
| D | qca,ath79-cpu-intc.txt | 5 qca,ddr-wb-channels and qca,ddr-wb-channel-interrupts properties.
9 - compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-cpu-intc"
20 - qca,ddr-wb-channel-interrupts: List of the interrupts needing a write
22 - qca,ddr-wb-channels: List of phandles to the write buffer channels for
23 each interrupt. If qca,ddr-wb-channel-interrupts is not present the interrupt
29 compatible = "qca,ar9132-cpu-intc", "qca,ar7100-cpu-intc";
34 qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
35 qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
43 #qca,ddr-wb-channel-cells = <1>;
|
| D | qca,ath79-misc-intc.txt | 7 - compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or
8 "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc"
24 compatible = "qca,ar9132-misc-intc", "qca,ar7100-misc-intc";
37 compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc";
|
| /linux-6.12.1/Documentation/devicetree/bindings/memory-controllers/ |
| D | qca,ath79-ddr-controller.yaml | 4 $id: http://devicetree.org/schemas/memory-controllers/qca,ath79-ddr-controller.yaml#
22 - const: qca,ar9132-ddr-controller
23 - const: qca,ar7240-ddr-controller
26 - qca,ar7100-ddr-controller
27 - qca,ar7240-ddr-controller
29 "#qca,ddr-wb-channel-cells":
41 - "#qca,ddr-wb-channel-cells"
49 compatible = "qca,ar9132-ddr-controller",
50 "qca,ar7240-ddr-controller";
53 #qca,ddr-wb-channel-cells = <1>;
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/ |
| D | qca,ar803x.yaml | 4 $id: http://devicetree.org/schemas/net/qca,ar803x.yaml#
21 qca,clk-out-frequency:
26 qca,clk-out-strength:
31 qca,disable-smarteee:
35 qca,keep-pll-enabled:
43 qca,disable-hibernation-mode:
51 qca,smarteee-tw-us-100m:
57 qca,smarteee-tw-us-1g:
92 #include <dt-bindings/net/qca-ar803x.h>
103 qca,clk-out-frequency = <125000000>;
[all …]
|
| D | qca,ar71xx.yaml | 4 $id: http://devicetree.org/schemas/net/qca,ar71xx.yaml#
7 title: QCA AR71XX MAC
20 - qca,ar7100-eth # Atheros AR7100
21 - qca,ar7240-eth # Atheros AR7240
22 - qca,ar7241-eth # Atheros AR7241
23 - qca,ar7242-eth # Atheros AR7242
24 - qca,ar9130-eth # Atheros AR9130
25 - qca,ar9330-eth # Atheros AR9330
26 - qca,ar9340-eth # Atheros AR9340
27 - qca,qca9530-eth # Qualcomm Atheros QCA9530
[all …]
|
| D | qca,qca7000.txt | 13 - compatible : Should be "qca,qca7000"
26 - qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode.
47 compatible = "qca,qca7000";
66 - compatible : Should be "qca,qca7000"
83 compatible = "qca,qca7000";
|
| /linux-6.12.1/Documentation/devicetree/bindings/clock/ |
| D | qca,ath79-pll.txt | 6 - compatible: has to be "qca,<soctype>-pll" and one of the following
8 - "qca,ar7100-pll"
9 - "qca,ar7240-pll"
10 - "qca,ar9130-pll"
11 - "qca,ar9330-pll"
12 - "qca,ar9340-pll"
13 - "qca,qca9550-pll"
25 compatible = "qca,ar9132-pll", "qca,ar9130-pll";
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/dsa/ |
| D | qca8k.yaml | 28 - qca,qca8327
29 - qca,qca8328
30 - qca,qca8334
31 - qca,qca8337
33 qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package
34 qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package
35 qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package
36 qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package
46 qca,ignore-power-on-sel:
53 qca,led-open-drain:
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/reset/ |
| D | qca,ar7100-reset.yaml | 5 $id: http://devicetree.org/schemas/reset/qca,ar7100-reset.yaml#
17 - qca,ar9132-reset
18 - qca,ar9331-reset
19 - const: qca,ar7100-reset
37 compatible = "qca,ar9132-reset", "qca,ar7100-reset";
|
| /linux-6.12.1/Documentation/devicetree/bindings/gpio/ |
| D | gpio-ath79.txt | 4 - compatible: has to be "qca,<soctype>-gpio" and one of the following
6 - "qca,ar7100-gpio"
7 - "qca,ar9340-gpio"
26 compatible = "qca,ar9132-gpio", "qca,ar7100-gpio";
|
| /linux-6.12.1/drivers/irqchip/ |
| D | irq-ath79-cpu.c | 63 node, "qca,ddr-wb-channels", "#qca,ddr-wb-channel-cells"); in ar79_cpu_intc_of_init()
70 node, "qca,ddr-wb-channel-interrupts", i, &irq); in ar79_cpu_intc_of_init()
75 node, "qca,ddr-wb-channels", in ar79_cpu_intc_of_init()
76 "#qca,ddr-wb-channel-cells", in ar79_cpu_intc_of_init()
86 IRQCHIP_DECLARE(ar79_cpu_intc, "qca,ar7100-cpu-intc",
|
| /linux-6.12.1/Documentation/devicetree/bindings/spi/ |
| D | spi-ath79.txt | 4 - compatible: has to be "qca,<soc-type>-spi", "qca,ar7100-spi" as fallback.
16 compatible = "qca,ar9132-spi", "qca,ar7100-spi";
|
| /linux-6.12.1/arch/mips/ath79/ |
| D | clock.c | 633 if (of_device_is_compatible(np, "qca,ar7100-pll")) in ath79_clocks_init_dt()
635 else if (of_device_is_compatible(np, "qca,ar7240-pll") || in ath79_clocks_init_dt()
636 of_device_is_compatible(np, "qca,ar9130-pll")) in ath79_clocks_init_dt()
638 else if (of_device_is_compatible(np, "qca,ar9330-pll")) in ath79_clocks_init_dt()
640 else if (of_device_is_compatible(np, "qca,ar9340-pll")) in ath79_clocks_init_dt()
642 else if (of_device_is_compatible(np, "qca,qca9530-pll")) in ath79_clocks_init_dt()
644 else if (of_device_is_compatible(np, "qca,qca9550-pll")) in ath79_clocks_init_dt()
646 else if (of_device_is_compatible(np, "qca,qca9560-pll")) in ath79_clocks_init_dt()
666 CLK_OF_DECLARE(ar7100_clk, "qca,ar7100-pll", ath79_clocks_init_dt);
667 CLK_OF_DECLARE(ar7240_clk, "qca,ar7240-pll", ath79_clocks_init_dt);
[all …]
|
| /linux-6.12.1/arch/arm64/boot/dts/freescale/ |
| D | fsl-ls1028a-kontron-sl28-var4.dts | 14 #include <dt-bindings/net/qca-ar803x.h>
26 qca,clk-out-frequency = <125000000>;
27 qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
28 qca,keep-pll-enabled;
|
| D | fsl-ls1028a-kontron-sl28-var1.dts | 17 #include <dt-bindings/net/qca-ar803x.h>
32 qca,clk-out-frequency = <125000000>;
33 qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
34 qca,keep-pll-enabled;
|
| /linux-6.12.1/arch/arm/boot/dts/broadcom/ |
| D | bcm958625-meraki-alamo.dtsi | 109 compatible = "qca,qca8337";
120 qca,sgmii-enable-pll;
121 qca,sgmii-txclk-falling-edge;
187 compatible = "qca,qca8337";
198 qca,sgmii-enable-pll;
199 qca,sgmii-txclk-falling-edge;
|