Searched full:port4 (Results 1 – 25 of 46) sorted by relevance
12
| /linux-6.12.1/drivers/scsi/mvsas/ |
| D | mv_64xx.h | 57 MVS_P4_INT_STAT = 0x200, /* Port4 interrupt status */
58 MVS_P4_INT_MASK = 0x204, /* Port4 interrupt enable mask */
63 MVS_P4_SER_CTLSTAT = 0x220, /* port4 serial control/status */
72 MVS_P4_CFG_ADDR = 0x230, /* Port4 config address */
73 MVS_P4_CFG_DATA = 0x234, /* Port4 config data */
79 MVS_P4_VSR_ADDR = 0x250, /* port4 VSR addr */
80 MVS_P4_VSR_DATA = 0x254, /* port4 VSR data */
|
| D | mv_94xx.h | 76 MVS_P4_INT_STAT = 0x1A0, /* Port4 interrupt status */
77 MVS_P4_INT_MASK = 0x1A4, /* Port4 interrupt enable mask */
82 MVS_P4_SER_CTLSTAT = 0x1E0, /* port4 serial control/status */
88 MVS_P4_CFG_ADDR = 0x220, /* Port4 config address */
89 MVS_P4_CFG_DATA = 0x224, /* Port4 config data */
|
| /linux-6.12.1/Documentation/gpu/dp-mst/ |
| D | topology-figure-2.dot | 14 driver -> port4 [color=red];
28 port2 -> mstb3 -> {port3, port4};
38 mstb3 -> port4;
50 port4 [label="Port #4";style=filled;fillcolor=grey];
|
| D | topology-figure-1.dot | 14 driver -> port4;
27 port2 -> mstb3 -> {port3, port4};
34 port2 -> mstb3 -> {port3, port4};
51 port4 [label="Port #4";shape=oval];
|
| D | topology-figure-3.dot | 17 driver -> port4 [color=grey];
30 port2 -> mstb3 -> {port3, port4};
41 mstb3 -> port4;
53 port4 [label="Port #4";style=filled;fillcolor=grey];
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/ |
| D | mscc,vsc7514-switch.yaml | 66 - description: Port4 target
91 - const: port4
154 "port2", "port3", "port4", "port5", "port6",
201 "port2", "port3", "port4", "port5", "port6",
|
| /linux-6.12.1/Documentation/admin-guide/media/ |
| D | raspberrypi-pisp-be.dot | 3 …<port0> 0 | <port1> 1 | <port2> 2 | <port7> 7} | pispbe\n | {<port3> 3 | <port4> 4 | <port5> 5 | <…
5 n00000001:port4 -> n00000022 [style=bold]
|
| D | imx6q-sabresd.dot | 45 …imx6-mipi-csi2\n/dev/v4l-subdev12 | {<port1> 1 | <port2> 2 | <port3> 3 | <port4> 4}}", shape=Mreco…
49 n00000079:port4 -> n00000083:port0 [style=dashed]
|
| D | starfive_camss_graph.dot | 7 …cdns_csi2rx.19800000.csi-bridge\n | {<port1> 1 | <port2> 2 | <port3> 3 | <port4> 4}}", shape=Mreco…
|
| /linux-6.12.1/arch/arm/boot/dts/renesas/ |
| D | r7s72100-genmai.dts | 66 gpios = <&port4 10 GPIO_ACTIVE_LOW>;
70 gpios = <&port4 11 GPIO_ACTIVE_LOW>;
|
| D | r7s72100-gr-peach.dts | 130 reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>;
|
| /linux-6.12.1/arch/mips/boot/dts/mscc/ |
| D | ocelot.dtsi | 142 "port2", "port3", "port4", "port5", "port6",
168 port4: port@4 { label
|
| D | ocelot_pcb120.dts | 95 &port4 {
|
| /linux-6.12.1/include/dt-bindings/pinctrl/ |
| D | r7s9210-pinctrl.h | 16 #define PORT4 4 macro
|
| /linux-6.12.1/Documentation/driver-api/cxl/ |
| D | memory-devices.rst | 115 "port":"port4",
117 "ports:port4":[
|
| /linux-6.12.1/arch/arm/boot/dts/marvell/ |
| D | kirkwood-4i-edge-200.dts | 107 label = "port4";
|
| /linux-6.12.1/drivers/net/wireguard/ |
| D | socket.c | 359 struct udp_port_cfg port4 = { in wg_socket_init() local
387 ret = udp_sock_create(net, &port4, &new4); in wg_socket_init()
|
| /linux-6.12.1/arch/arm/boot/dts/broadcom/ |
| D | bcm958622hr.dts | 201 label = "port4";
|
| D | bcm958623hr.dts | 205 label = "port4";
|
| D | bcm988312hr.dts | 213 label = "port4";
|
| D | bcm958625hr.dts | 220 label = "port4";
|
| /linux-6.12.1/arch/arm/boot/dts/microchip/ |
| D | lan966x-kontron-kswitch-d10-mmt.dtsi | 168 &port4 {
|
| D | lan966x-pcb8290.dts | 148 &port4 {
|
| /linux-6.12.1/include/uapi/linux/ |
| D | serial.h | 93 int port4; member
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/dsa/ |
| D | brcm,b53.yaml | 252 label = "port4";
|
12