| /linux-6.12.1/drivers/net/ |
| D | mdio.c | 3 * mdio.c: Generic support for MDIO-compatible transceivers
11 #include <linux/mdio.h>
14 MODULE_DESCRIPTION("Generic support for MDIO-compatible transceivers");
19 * mdio45_probe - probe for an MDIO (clause 45) device
20 * @mdio: MDIO interface
23 * This sets @prtad and @mmds in the MDIO interface if successful.
26 int mdio45_probe(struct mdio_if_info *mdio, int prtad) in mdio45_probe() argument
34 stat2 = mdio->mdio_read(mdio->dev, prtad, mmd, MDIO_STAT2); in mdio45_probe()
40 devs1 = mdio->mdio_read(mdio->dev, prtad, mmd, MDIO_DEVS1); in mdio45_probe()
41 devs2 = mdio->mdio_read(mdio->dev, prtad, mmd, MDIO_DEVS2); in mdio45_probe()
[all …]
|
| /linux-6.12.1/drivers/net/mdio/ |
| D | Kconfig | 3 # MDIO Layer Configuration
7 tristate "MDIO bus device drivers"
9 MDIO devices and driver infrastructure code.
27 FWNODE MDIO bus (Ethernet PHY) accessors
35 OpenFirmware MDIO bus (Ethernet PHY) accessors
42 ACPI MDIO bus (Ethernet PHY) accessors
50 tristate "Allwinner sun4i MDIO interface support"
53 This driver supports the MDIO interface found in the network
58 tristate "APM X-Gene SoC MDIO bus controller"
61 This module provides a driver for the MDIO busses found in the
[all …]
|
| D | Makefile | 2 # Makefile for Linux MDIO bus drivers
8 obj-$(CONFIG_MDIO_ASPEED) += mdio-aspeed.o
9 obj-$(CONFIG_MDIO_BCM_IPROC) += mdio-bcm-iproc.o
10 obj-$(CONFIG_MDIO_BCM_UNIMAC) += mdio-bcm-unimac.o
11 obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o
12 obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium.o
13 obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
14 obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o
15 obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o
16 obj-$(CONFIG_MDIO_IPQ4019) += mdio-ipq4019.o
[all …]
|
| D | mdio-mvusb.c | 27 struct mii_bus *mdio; member
32 static int mvusb_mdio_read(struct mii_bus *mdio, int dev, int reg) in mvusb_mdio_read() argument
34 struct mvusb_mdio *mvusb = mdio->priv; in mvusb_mdio_read()
52 static int mvusb_mdio_write(struct mii_bus *mdio, int dev, int reg, u16 val) in mvusb_mdio_write() argument
54 struct mvusb_mdio *mvusb = mdio->priv; in mvusb_mdio_write()
69 struct mii_bus *mdio; in mvusb_mdio_probe() local
72 mdio = devm_mdiobus_alloc_size(dev, sizeof(*mvusb)); in mvusb_mdio_probe()
73 if (!mdio) in mvusb_mdio_probe()
76 mvusb = mdio->priv; in mvusb_mdio_probe()
77 mvusb->mdio = mdio; in mvusb_mdio_probe()
[all …]
|
| D | of_mdio.c | 3 * OF helpers for the MDIO (Ethernet PHY) API
28 MODULE_DESCRIPTION("OpenFirmware MDIO bus (Ethernet PHY) accessors");
37 int of_mdiobus_phy_device_register(struct mii_bus *mdio, struct phy_device *phy, in of_mdiobus_phy_device_register() argument
40 return fwnode_mdiobus_phy_device_register(mdio, phy, in of_mdiobus_phy_device_register()
46 static int of_mdiobus_register_phy(struct mii_bus *mdio, in of_mdiobus_register_phy() argument
49 return fwnode_mdiobus_register_phy(mdio, of_fwnode_handle(child), addr); in of_mdiobus_register_phy()
52 static int of_mdiobus_register_device(struct mii_bus *mdio, in of_mdiobus_register_device() argument
59 mdiodev = mdio_device_create(mdio, addr); in of_mdiobus_register_device()
78 dev_dbg(&mdio->dev, "registered mdio device %pOFn at address %i\n", in of_mdiobus_register_device()
86 * to have a compatible string, so they can be matched to an MDIO
[all …]
|
| D | acpi_mdio.c | 3 * ACPI helpers for the MDIO (Ethernet PHY) API
19 MODULE_DESCRIPTION("ACPI MDIO bus (Ethernet PHY) accessors");
23 * @mdio: pointer to mii_bus structure
24 * @fwnode: pointer to fwnode of MDIO bus. This fwnode is expected to represent
25 * @owner: module owning this @mdio object.
26 * an ACPI device object corresponding to the MDIO bus and its children are
32 int __acpi_mdiobus_register(struct mii_bus *mdio, struct fwnode_handle *fwnode, in __acpi_mdiobus_register() argument
40 mdio->phy_mask = GENMASK(31, 0); in __acpi_mdiobus_register()
41 ret = __mdiobus_register(mdio, owner); in __acpi_mdiobus_register()
45 ACPI_COMPANION_SET(&mdio->dev, to_acpi_device_node(fwnode)); in __acpi_mdiobus_register()
[all …]
|
| D | mdio-gpio.c | 3 * GPIO based MDIO bitbang driver.
22 #include <linux/mdio-bitbang.h>
23 #include <linux/mdio-gpio.h>
26 #include <linux/platform_data/mdio-gpio.h>
32 struct gpio_desc *mdc, *mdio, *mdo; member
43 bitbang->mdio = devm_gpiod_get_index(dev, NULL, MDIO_GPIO_MDIO, in mdio_gpio_get_data()
45 if (IS_ERR(bitbang->mdio)) in mdio_gpio_get_data()
46 return PTR_ERR(bitbang->mdio); in mdio_gpio_get_data()
69 gpiod_direction_output(bitbang->mdio, 1); in mdio_dir()
71 gpiod_direction_input(bitbang->mdio); in mdio_dir()
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/ |
| D | fsl,fman-mdio.yaml | 4 $id: http://devicetree.org/schemas/net/fsl,fman-mdio.yaml#
7 title: Freescale Frame Manager MDIO Device
12 description: FMan MDIO Node.
13 The MDIO is a bus to which the PHY devices are connected.
18 - fsl,fman-mdio
20 - fsl,fman-memac-mdio
22 Must include "fsl,fman-mdio" for 1 Gb/s MDIO from FMan v2.
23 Must include "fsl,fman-xmdio" for 10 Gb/s MDIO from FMan v2.
24 Must include "fsl,fman-memac-mdio" for 1/10 Gb/s MDIO from
38 fsl,fman-internal-mdio:
[all …]
|
| D | brcm,unimac-mdio.yaml | 4 $id: http://devicetree.org/schemas/net/brcm,unimac-mdio.yaml#
7 title: Broadcom UniMAC MDIO bus controller
15 - $ref: mdio.yaml#
20 - brcm,genet-mdio-v1
21 - brcm,genet-mdio-v2
22 - brcm,genet-mdio-v3
23 - brcm,genet-mdio-v4
24 - brcm,genet-mdio-v5
25 - brcm,asp-v2.0-mdio
26 - brcm,asp-v2.1-mdio
[all …]
|
| D | allwinner,sun8i-a83t-emac.yaml | 127 mdio-mux:
133 const: allwinner,sun8i-h3-mdio-mux
135 mdio-parent-bus:
138 Phandle to EMAC MDIO.
146 mdio@1:
147 $ref: mdio.yaml#
149 description: Internal MDIO Bus
153 const: allwinner,sun8i-h3-mdio-internal
178 mdio@2:
179 $ref: mdio.yaml#
[all …]
|
| D | qcom,ipq4019-mdio.yaml | 4 $id: http://devicetree.org/schemas/net/qcom,ipq4019-mdio.yaml#
7 title: Qualcomm IPQ40xx MDIO Controller
16 - qcom,ipq4019-mdio
17 - qcom,ipq5018-mdio
21 - qcom,ipq6018-mdio
22 - qcom,ipq8074-mdio
23 - qcom,ipq9574-mdio
24 - const: qcom,ipq4019-mdio
36 the first Address and length of the register set for the MDIO controller.
42 - description: MDIO clock source frequency fixed to 100MHZ
[all …]
|
| D | fsl,cpm-mdio.yaml | 4 $id: http://devicetree.org/schemas/net/fsl,cpm-mdio.yaml#
7 title: Freescale CPM MDIO Device
16 - fsl,pq1-fec-mdio
17 - fsl,cpm2-mdio-bitbang
19 - const: fsl,mpc8272ads-mdio-bitbang
20 - const: fsl,mpc8272-mdio-bitbang
21 - const: fsl,cpm2-mdio-bitbang
26 fsl,mdio-pin:
28 description: pin of port C controlling mdio data
32 description: pin of port C controlling mdio clock
[all …]
|
| D | cavium-mdio.txt | 1 * System Management Interface (SMI) / MDIO
6 "cavium,octeon-3860-mdio": Compatibility with all cn3XXX, cn5XXX
9 "cavium,thunder-8890-mdio": Compatibility with all cn8XXX SOCs.
11 - reg: The base address of the MDIO bus controller register bank.
15 - #size-cells: Must be <0>. MDIO addresses have no size component.
17 Typically an MDIO bus might have several children.
20 mdio@1180000001800 {
21 compatible = "cavium,octeon-3860-mdio";
33 * System Management Interface (SMI) / MDIO Nexus
35 Several mdio buses may be gathered as children of a single PCI
[all …]
|
| D | mdio-mux-multiplexer.yaml | 4 $id: http://devicetree.org/schemas/net/mdio-mux-multiplexer.yaml#
7 title: Properties for an MDIO bus multiplexer consumer device
13 This is a special case of MDIO mux when MDIO mux is defined as a consumer
19 - $ref: /schemas/net/mdio-mux.yaml#
23 const: mdio-mux-multiplexer
43 mdio-mux-1 { // Mux consumer
44 compatible = "mdio-mux-multiplexer";
46 mdio-parent-bus = <&emdio1>;
50 mdio@0 {
56 mdio@8 {
[all …]
|
| D | hisilicon-hns-mdio.txt | 1 Hisilicon MDIO bus controller
5 "hisilicon,hns-mdio"
6 "hisilicon,mdio"
7 "hisilicon,hns-mdio" is recommended to be used for hip05 and later SOCs,
8 while "hisilicon,mdio" is optional for backwards compatibility only on
10 - reg: The base address of the MDIO bus controller register bank.
12 - #size-cells: Must be <0>. MDIO addresses have no size component.
14 Typically an MDIO bus might have several children.
17 mdio@803c0000 {
20 compatible = "hisilicon,hns-mdio","hisilicon,mdio";
|
| D | mdio-mux-mmioreg.yaml | 4 $id: http://devicetree.org/schemas/net/mdio-mux-mmioreg.yaml#
7 title: Properties for an MDIO bus multiplexer controlled by a memory-mapped device
13 This is a special case of a MDIO bus multiplexer. A memory-mapped device,
14 like an FPGA, is used to control which child bus is connected. The mdio-mux
19 - $ref: /schemas/net/mdio-mux.yaml#
24 - const: mdio-mux-mmioreg
25 - const: mdio-mux
37 child mdio-mux node must be constrained by this mask.
48 mdio-mux@9 {
49 compatible = "mdio-mux-mmioreg", "mdio-mux";
[all …]
|
| D | amlogic,gxl-mdio-mux.yaml | 4 $id: http://devicetree.org/schemas/net/amlogic,gxl-mdio-mux.yaml#
7 title: Amlogic GXL MDIO bus multiplexer
13 This is a special case of a MDIO bus multiplexer. It allows to choose between
14 the internal mdio bus leading to the embedded 10/100 PHY or the external
15 MDIO bus on the Amlogic GXL SoC family.
18 - $ref: mdio-mux.yaml#
22 const: amlogic,gxl-mdio-mux
44 eth_phy_mux: mdio@558 {
45 compatible = "amlogic,gxl-mdio-mux";
51 mdio-parent-bus = <&mdio0>;
[all …]
|
| D | brcm,mdio-mux-iproc.yaml | 4 $id: http://devicetree.org/schemas/net/brcm,mdio-mux-iproc.yaml#
7 title: MDIO bus multiplexer found in Broadcom iProc based SoCs.
13 This MDIO bus multiplexer defines buses that could be internal as well as
14 external to SoCs and could accept MDIO transaction compatible to C-22 or
16 properties as well to generate desired MDIO transaction on appropriate bus.
19 - $ref: /schemas/net/mdio-mux.yaml#
23 const: brcm,mdio-mux-iproc
30 description: core clock driving the MDIO block
41 mdio_mux_iproc: mdio-mux@66020000 {
42 compatible = "brcm,mdio-mux-iproc";
[all …]
|
| D | amlogic,g12a-mdio-mux.yaml | 4 $id: http://devicetree.org/schemas/net/amlogic,g12a-mdio-mux.yaml#
7 title: MDIO bus multiplexer/glue of Amlogic G12a SoC family
10 This is a special case of a MDIO bus multiplexer. It allows to choose between
11 the internal mdio bus leading to the embedded 10/100 PHY or the external
12 MDIO bus.
18 - $ref: mdio-mux.yaml#
22 const: amlogic,g12a-mdio-mux
51 mdio-multiplexer@4c000 {
52 compatible = "amlogic,g12a-mdio-mux";
56 mdio-parent-bus = <&mdio0>;
[all …]
|
| D | apm-xgene-mdio.txt | 1 APM X-Gene SoC MDIO node
3 MDIO node is defined to describe on-chip MDIO controller.
6 - compatible: Must be "apm,xgene-mdio-rgmii" or "apm,xgene-mdio-xfi"
12 For the phys on the mdio bus, there must be a node with the following fields:
18 mdio: mdio@17020000 {
19 compatible = "apm,xgene-mdio-rgmii";
27 &mdio {
|
| /linux-6.12.1/drivers/net/pcs/ |
| D | pcs-lynx.c | 3 * Lynx PCS MDIO helpers
6 #include <linux/mdio.h>
25 struct mdio_device *mdio; member
91 phylink_mii_c22_pcs_get_state(lynx->mdio, state); in lynx_pcs_get_state()
94 lynx_pcs_get_state_2500basex(lynx->mdio, state); in lynx_pcs_get_state()
97 lynx_pcs_get_state_usxgmii(lynx->mdio, state); in lynx_pcs_get_state()
100 phylink_mii_c45_pcs_get_state(lynx->mdio, state); in lynx_pcs_get_state()
106 dev_dbg(&lynx->mdio->dev, in lynx_pcs_get_state()
180 return lynx_pcs_config_giga(lynx->mdio, ifmode, advertising, in lynx_pcs_config()
184 dev_err(&lynx->mdio->dev, in lynx_pcs_config()
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/net/dsa/ |
| D | realtek.yaml | 18 MDIO or SPI.
21 bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
22 not use the MDIO protocol. This binding defines how to specify the
26 The MDIO-connected switches use MDIO protocol to access their registers.
27 The realtek-mdio driver is an MDIO driver and it must be inserted inside
28 an MDIO node.
54 mdio-gpios:
55 description: GPIO line for the MDIO data line.
103 mdio:
104 $ref: /schemas/net/mdio.yaml#
[all …]
|
| /linux-6.12.1/arch/arm64/boot/dts/freescale/ |
| D | fsl-lx2160a-qds.dts | 35 mdio-mux-1 {
36 compatible = "mdio-mux-multiplexer";
38 mdio-parent-bus = <&emdio1>;
42 mdio@0 { /* On-board PHY #1 RGMI1*/
48 mdio@8 { /* On-board PHY #2 RGMI2*/
54 mdio@18 { /* Slot #1 */
60 mdio@19 { /* Slot #2 */
66 mdio@1a { /* Slot #3 */
72 mdio@1b { /* Slot #4 */
78 mdio@1c { /* Slot #5 */
[all …]
|
| D | fsl-lx2162a-qds.dts | 33 mdio-mux-1 {
34 compatible = "mdio-mux-multiplexer";
36 mdio-parent-bus = <&emdio1>;
40 mdio@0 { /* On-board RTL8211F PHY #1 RGMII1 */
52 mdio@8 { /* On-board RTL8211F PHY #2 RGMII2 */
64 mdio@18 { /* Slot #1 */
70 mdio@19 { /* Slot #2 */
76 mdio@1a { /* Slot #3 */
82 mdio@1b { /* Slot #4 */
88 mdio@1c { /* Slot #5 */
[all …]
|
| /linux-6.12.1/drivers/net/ethernet/xilinx/ |
| D | xilinx_axienet_mdio.c | 3 * MDIO bus driver for the Xilinx Axi Ethernet device
24 * axienet_mdio_wait_until_ready - MDIO wait function
29 * Wait till MDIO interface is ready to accept a new transaction.
41 * axienet_mdio_mdc_enable - MDIO MDC enable function
44 * Enable the MDIO MDC. Called prior to a read/write operation
53 * axienet_mdio_mdc_disable - MDIO MDC disable function
56 * Disable the MDIO MDC. Called after a read/write operation
68 * axienet_mdio_read - MDIO interface read function
117 * axienet_mdio_write - MDIO interface write function
165 * axienet_mdio_enable - MDIO hardware setup function
[all …]
|