| /linux-6.12.1/drivers/regulator/ |
| D | tps65912-regulator.c | 20 LDO4, LDO5, LDO6, LDO7, LDO8, LDO9, LDO10 }; enumerator
100 TPS65912_REGULATOR("LDO6", LDO6, "ldo6", tps65912_ops_ldo,
|
| D | qcom-rpmh-regulator.c | 945 RPMH_VREG("ldo6", "ldo%s6", &pmic4_pldo, "vdd-l6"),
1007 RPMH_VREG("ldo6", "ldo%s6", &pmic5_nldo, "vdd-l6-l9"),
1037 RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l4-l5-l6"),
1063 RPMH_VREG("ldo6", "ldo%s6", &pmic5_nldo, "vdd-l6-l9"),
1094 RPMH_VREG("ldo6", "ldo%s6", &pmic5_nldo515, "vdd-l6-l7"),
1119 RPMH_VREG("ldo6", "ldo%s6", &pmic5_nldo, "vdd-l6-l9-l10"),
1143 RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l6-l9-l11"),
1175 RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l6-l7"),
1243 RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l5-l6"),
1256 RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l5-l6"),
[all …]
|
| D | bd96801-regulator.c | 276 BD96801_IRQINFO(BD96801_PROT_OCP, "ldo6-overcurr", 500,
277 "bd96801-ldo6-overcurr"),
278 BD96801_IRQINFO(BD96801_PROT_OVP, "ldo6-over-voltage", 500,
279 "bd96801-ldo6-overvolt"),
280 BD96801_IRQINFO(BD96801_PROT_UVP, "ldo6-under-voltage", 500,
281 "bd96801-ldo6-undervolt"),
652 .name = "ldo6",
653 .of_match = of_match_ptr("ldo6"),
|
| D | pcf50633-regulator.c | 67 PCF50633_REGULATOR("ldo6", LDO6, 900000, 100000, 0, 28),
|
| D | da9052-regulator.c | 340 DA9052_LDO(LDO6, ldo6, 50, 1200, 3600, 6, 6, 0),
357 DA9052_LDO(LDO6, ldo6, 50, 1200, 3600, 6, 6, 0),
|
| /linux-6.12.1/Documentation/devicetree/bindings/regulator/ |
| D | palmas-pmic.txt | 26 - ti,ldo6-vibrator : ldo6 is in vibrator mode
66 ti,ldo6-vibrator;
|
| D | mt6360-regulator.yaml | 25 description: Input supply phandle(s) for LDO6/7
64 ldo6 {
65 regulator-name = "mt6360,ldo6";
|
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
70 LDO6 {
71 regulator-name = "ldo6";
|
| D | max8925-regulator.txt | 13 - LDO6 for LDO LDO6
|
| D | rohm,bd71847-regulator.yaml | 21 regulator-boot-on at least for BUCK5. LDO6 is supplied by it and it must
23 voltage monitoring for LDO5/LDO6 can cause PMIC to reset.
27 # LDO1, LDO2, LDO3, LDO4, LDO5, LDO6
40 should be "ldo1", ..., "ldo6"
|
| D | dlg,slg51000.yaml | 42 Input supply for ldo6, required if regulator is enabled
119 ldo6 {
|
| D | rohm,bd71837-regulator.yaml | 22 disabled by driver at startup. LDO5 and LDO6 are supplied by those and
23 if they are disabled at startup the voltage monitoring for LDO5/LDO6 will
28 # LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
|
| D | tps6586x.txt | 22 - vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8
115 ldo6_reg: ldo6 {
|
| /linux-6.12.1/Documentation/devicetree/bindings/mfd/ |
| D | st,stpmic1.yaml | 97 - ldo6 for LDO LDO6
304 ldo6-supply = <&v3v3>;
330 ldo6 {
|
| D | da9052-i2c.txt | 28 ldo6 : regulator LDO6
|
| D | da9055.txt | 40 ldo6 : regulator LDO6
|
| D | rohm,bd71828-pmic.yaml | 184 ldo6: LDO6 {
185 regulator-name = "ldo6";
|
| D | rohm,bd71847-pmic.yaml | 221 ldo6: LDO6 {
222 regulator-name = "ldo6";
|
| D | rohm,bd71837-pmic.yaml | 232 ldo6: LDO6 {
233 regulator-name = "ldo6";
|
| D | tps65910.txt | 26 ldo6, ldo7, ldo8
46 vcc3-supply: LDO6, LDO7 and LDO8 input.
181 regulator-compatible = "ldo6";
|
| /linux-6.12.1/drivers/mfd/ |
| D | rohm-bd96801.c | 84 DEFINE_RES_IRQ_NAMED(BD96801_LDO6_OCPH_STAT, "bd96801-ldo6-overcurr"),
85 DEFINE_RES_IRQ_NAMED(BD96801_LDO6_OVD_STAT, "bd96801-ldo6-overvolt"),
86 DEFINE_RES_IRQ_NAMED(BD96801_LDO6_UVD_STAT, "bd96801-ldo6-undervolt"),
169 /* LDO6 INTB */
|
| /linux-6.12.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mn-ddr4-evk.dts | 151 ldo6_reg: LDO6 {
152 regulator-name = "ldo6";
|
| D | imx8mq-pico-pi.dts | 180 ldo6: LDO6 { label
181 regulator-name = "ldo6";
|
| D | imx8mq-phanbell.dts | 243 ldo6: LDO6 { label
244 regulator-name = "ldo6";
|
| /linux-6.12.1/include/linux/mfd/ |
| D | rohm-bd96801.h | 129 /* Reg 0x5a LDO6 ERR IRQs */
187 /* Reg 0x62 (LDO6 INTB) */
|