Home
last modified time | relevance | path

Searched +full:i2c +full:- +full:min +full:- +full:scl +full:- +full:pulse +full:- +full:width +full:- +full:us (Results 1 – 5 of 5) sorted by relevance

/linux-6.12.1/Documentation/devicetree/bindings/i2c/
Dst,sti-i2c.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/i2c/st,sti-i2c.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: I2C controller embedded in STMicroelectronics STi platform
10 - Patrice Chotard <patrice.chotard@foss.st.com>
13 - $ref: /schemas/i2c/i2c-controller.yaml#
18 - st,comms-ssc-i2c
19 - st,comms-ssc4-i2c
30 clock-names:
[all …]
/linux-6.12.1/arch/arm/boot/dts/st/
Dstihxxx-b2120.dtsi1 // SPDX-License-Identifier: GPL-2.0-only
6 #include <dt-bindings/clock/stih407-clks.h>
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/media/c8sectpfe.h>
11 compatible = "gpio-leds";
12 led-red {
15 linux,default-trigger = "heartbeat";
17 led-green {
19 default-state = "off";
24 compatible = "simple-audio-card";
[all …]
Dstih418-b2199.dts1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
11 compatible = "st,stih418-b2199", "st,stih418";
14 stdout-path = &sbc_serial0;
28 compatible = "gpio-leds";
29 led-red {
32 linux,default-trigger = "heartbeat";
34 led-green {
36 default-state = "off";
[all …]
Dstih410-b2260.dts1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
12 compatible = "st,stih410-b2260", "st,stih410";
15 stdout-path = &uart1;
29 compatible = "gpio-leds";
30 led-user-green-1 {
33 linux,default-trigger = "heartbeat";
34 default-state = "off";
37 led-user-green-2 {
[all …]
/linux-6.12.1/drivers/i2c/busses/
Di2c-st.c1 // SPDX-License-Identifier: GPL-2.0-only
5 * I2C controller driver, used in STMicroelectronics devices.
13 #include <linux/i2c.h>
93 /* SSC I2C Control */
130 * struct st_i2c_timings - per-Mode tuning parameters
131 * @rate: I2C bus rate
132 * @rep_start_hold: I2C repeated start hold time requirement
133 * @rep_start_setup: I2C repeated start set up time requirement
134 * @start_hold: I2C start hold time requirement
135 * @data_setup_time: I2C data set up time requirement
[all …]