Searched +full:fb +full:- +full:pull +full:- +full:up +full:- +full:microvolt (Results 1 – 5 of 5) sorted by relevance
| /linux-6.12.1/arch/arm/boot/dts/nxp/imx/ |
| D | imx53-usbarmory.dts | 8 * This file is dual-licensed: you can use it either under the terms
47 /dts-v1/;
52 compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
57 stdout-path = &uart1;
66 compatible = "gpio-leds";
67 pinctrl-names = "default";
68 pinctrl-0 = <&pinctrl_led>;
70 led-user {
73 linux,default-trigger = "heartbeat";
83 operating-points = <
[all …]
|
| /linux-6.12.1/Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd71847-regulator.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/regulator/rohm,bd71847-regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <mazziesaccount@gmail.com>
15 Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
21 regulator-boot-on at least for BUCK5. LDO6 is supplied by it and it must
30 "^LDO[1-6]$":
37 regulator-name:
38 pattern: "^ldo[1-6]$"
[all …]
|
| D | rohm,bd71837-regulator.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/regulator/rohm,bd71837-regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Matti Vaittinen <mazziesaccount@gmail.com>
15 Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.yaml
21 regulator-boot-on at least for BUCK6 and BUCK7 so that those are not
31 "^LDO[1-7]$":
38 regulator-name:
39 pattern: "^ldo[1-7]$"
[all …]
|
| /linux-6.12.1/arch/arm64/boot/dts/qcom/ |
| D | msm8992-lg-h815.dts | 1 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
8 /dts-v1/;
13 #include <dt-bindings/leds/common.h>
16 /delete-node/ &cont_splash_mem;
19 /delete-node/ &dfps_data_mem;
24 chassis-type = "handset";
26 qcom,msm-id = <0xfb 0x0>;
27 qcom,pmic-id = <0x10009 0x1000a 0x0 0x0>;
28 qcom,board-id = <0xb64 0x0>;
31 /delete-node/ psci;
[all …]
|
| /linux-6.12.1/drivers/regulator/ |
| D | bd718x7-regulator.c | 1 // SPDX-License-Identifier: GPL-2.0
3 // bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver
10 #include <linux/mfd/rohm-bd718x7.h>
51 * controlled by software - or by PMIC internal HW state machine. Whether
52 * regulator should be under SW or HW control can be defined from device-tree.
103 * Note for next hacker - these PMICs have a register where the HW state can be
104 * read. If assuming RUN appears to be false in your use-case - you can
123 ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val); in bd71837_get_buck34_enable_hwctrl()
138 * guarantee minimum of 1ms sleep - it shouldn't matter if we in voltage_change_done()
143 ret = regmap_clear_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2, in voltage_change_done()
[all …]
|