Home
last modified time | relevance | path

Searched +full:ave +full:- +full:ctrl (Results 1 – 25 of 36) sorted by relevance

12

/linux-6.12.1/Documentation/devicetree/bindings/mfd/
Dmxs-lradc.txt4 - compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc"
6 - reg: Address and length of the register set for the device
7 - interrupts: Should contain the LRADC interrupts
10 - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
14 - fsl,ave-ctrl: number of samples per direction to calculate an average value.
16 - fsl,ave-delay: delay between consecutive samples. Allowed value is
17 2 ... 2048. It is used if 'fsl,ave-ctrl' > 1, counts at
19 - fsl,settling: delay between plate switch to next sample. Allowed value is
26 compatible = "fsl,imx23-lradc";
29 fsl,lradc-touchscreen-wires = <4>;
[all …]
Dst,stmpe.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
15 - Linus Walleij <linus.walleij@linaro.org>
18 - $ref: /schemas/spi/spi-peripheral-props.yaml#
23 - st,stmpe601
24 - st,stmpe801
25 - st,stmpe811
26 - st,stmpe1600
27 - st,stmpe1601
[all …]
/linux-6.12.1/arch/arm/boot/dts/intel/socfpga/
Dsocfpga_cyclone5_mcvevk.dts1 // SPDX-License-Identifier: GPL-2.0+
10 compatible = "denx,mcvevk", "altr,socfpga-cyclone5", "altr,socfpga";
14 stmpe-i2c0 = &stmpe1;
18 stdout-path = "serial0:115200n8";
31 phy-mode = "rgmii";
49 clock-frequency = <100000>;
53 #address-cells = <1>;
54 #size-cells = <0>;
58 irq-gpio = <&portb 28 0x4>; /* GPIO 57, trig. level HI */
61 compatible = "st,stmpe-ts";
[all …]
/linux-6.12.1/arch/arm/mach-omap1/
Dcommon.h23 * 675 Mass Ave, Cambridge, MA 02139, USA.
29 #include <linux/platform_data/i2c-omap.h>
58 unsigned int ctrl);
66 return -ENODEV; in omap_32k_timer_init()
/linux-6.12.1/arch/arm/boot/dts/nxp/imx/
Dimx53-m53.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later
10 compatible = "aries,imx53-m53", "denx,imx53-m53", "fsl,imx53";
18 reg_3p2v: regulator-3p2v {
19 compatible = "regulator-fixed";
20 regulator-name = "3P2V";
21 regulator-min-microvolt = <3200000>;
22 regulator-max-microvolt = <3200000>;
23 regulator-always-on;
26 reg_backlight: regulator-backlight {
27 compatible = "regulator-fixed";
[all …]
Dimx6ul-phytec-segin-peb-av-02.dtsi1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
9 backlight_lcd: backlight-lcd {
10 compatible = "pwm-backlight";
11 brightness-levels = <0 4 8 16 32 64 128 255>;
12 default-brightness-level = <5>;
13 power-supply = <&reg_backlight_en>;
18 lcd_panel: lcd-panel {
25 remote-endpoint = <&lcdif_parallel_out>;
30 reg_backlight_en: regulator-backlight-en {
31 compatible = "regulator-fixed";
[all …]
Dimx6ul-isiot.dtsi1 // SPDX-License-Identifier: GPL-2.0 OR X11
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/input/input.h>
18 stdout-path = &uart1;
22 compatible = "pwm-backlight";
24 brightness-levels = < 0 1 2 3 4 5 6 7 8 9
35 default-brightness-level = <100>;
38 reg_1p8v: regulator-1p8v {
39 compatible = "regulator-fixed";
40 regulator-name = "1P8V";
[all …]
Dimx6qdl-phytec-mira.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
14 compatible = "pwm-backlight";
15 brightness-levels = <0 4 8 16 32 64 128 255>;
16 default-brightness-level = <7>;
17 power-supply = <&reg_backlight>;
23 compatible = "gpio-leds";
24 pinctrl-names = "default";
25 pinctrl-0 = <&pinctrl_gpioleds>;
28 led-red {
29 label = "phyboard-mira:red";
[all …]
Dmba6ulx.dtsi1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3 * Copyright 2018-2022 TQ-Systems GmbH
4 * Author: Markus Niebel <Markus.Niebel@tq-group.com>
8 model = "TQ-Systems MBA6ULx Baseboard";
18 stdout-path = &uart1;
22 compatible = "pwm-backlight";
23 power-supply = <&reg_mba6ul_3v3>;
24 enable-gpios = <&expander_out0 4 GPIO_ACTIVE_HIGH>;
29 compatible = "gpio-beeper";
33 gpio_buttons: gpio-keys {
[all …]
Dimx6qdl-colibri.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
3 * Copyright 2014-2022 Toradex
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/pwm/pwm.h>
18 /delete-property/ mmc2;
19 /delete-property/ mmc3;
23 compatible = "pwm-backlight";
24 brightness-levels = <0 45 63 88 119 158 203 255>;
25 default-brightness-level = <4>;
26 enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
[all …]
Dimx6q-novena.dts2 * Copyright 2015 Sutajio Ko-Usagi PTE LTD
4 * This file is dual-licensed: you can use it either under the terms
22 * MA 02110-1301 USA
49 /dts-v1/;
51 #include <dt-bindings/gpio/gpio.h>
52 #include <dt-bindings/input/input.h>
56 compatible = "kosagi,imx6q-novena", "fsl,imx6q";
65 stdout-path = &uart2;
69 compatible = "pwm-backlight";
71 pinctrl-names = "default";
[all …]
/linux-6.12.1/arch/arm/boot/dts/nxp/mxs/
Dimx28-evk.dts1 // SPDX-License-Identifier: GPL-2.0+
5 /dts-v1/;
10 compatible = "fsl,imx28-evk", "fsl,imx28";
18 reg_3p3v: regulator-3p3v {
19 compatible = "regulator-fixed";
20 regulator-name = "3P3V";
21 regulator-min-microvolt = <3300000>;
22 regulator-max-microvolt = <3300000>;
23 regulator-always-on;
26 reg_vddio_sd0: regulator-vddio-sd0 {
[all …]
/linux-6.12.1/arch/arm/boot/dts/st/
Dspear1310-evb.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
8 /dts-v1/;
13 compatible = "st,spear1310-evb", "st,spear1310";
14 #address-cells = <1>;
15 #size-cells = <1>;
23 pinctrl-names = "default";
24 pinctrl-0 = <&state_default>;
63 smi-pmx {
127 label = "u-boot";
149 compatible = "gpio-keys";
[all …]
Dspear1340-evb.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
8 /dts-v1/;
13 compatible = "st,spear1340-evb", "st,spear1340";
14 #address-cells = <1>;
15 #size-cells = <1>;
23 pinctrl-names = "default";
24 pinctrl-0 = <&state_default>;
47 spdif-in {
51 spdif-out {
59 smi-pmx {
[all …]
Dspear320-hmi.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
8 /dts-v1/;
13 compatible = "st,spear320-hmi", "st,spear320";
14 #address-cells = <1>;
15 #size-cells = <1>;
23 st,pinmux-mode = <4>;
24 pinctrl-names = "default";
25 pinctrl-0 = <&state_default>;
107 label = "u-boot";
129 compatible = "gpio-keys";
[all …]
Dstm32f429-disco.dts2 * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
4 * This file is dual-licensed: you can use it either under the terms
22 * MA 02110-1301 USA
48 /dts-v1/;
50 #include "stm32f429-pinctrl.dtsi"
51 #include <dt-bindings/input/input.h>
52 #include <dt-bindings/interrupt-controller/irq.h>
53 #include <dt-bindings/gpio/gpio.h>
56 model = "STMicroelectronics STM32F429i-DISCO board";
57 compatible = "st,stm32f429i-disco", "st,stm32f429";
[all …]
Dstm32mp157c-phycore-stm32mp15-som.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de>
4 * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/arm-gic.h>
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/leds/common.h>
13 #include <dt-bindings/leds/leds-pca9532.h>
14 #include <dt-bindings/mfd/st,stpmic1.h>
[all …]
/linux-6.12.1/arch/arm/boot/dts/renesas/
Dr8a7745-iwg22d-sodimm.dts1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the iWave-RZG1E SODIMM carrier board
9 * SSI-SGTL5000
31 /dts-v1/;
32 #include "r8a7745-iwg22m.dtsi"
33 #include <dt-bindings/pwm/pwm.h>
36 model = "iWave Systems RainboW-G22D-SODIMM board based on RZ/G1E";
47 stdout-path = "serial3:115200n8";
51 compatible = "fixed-clock";
52 #clock-cells = <0>;
[all …]
/linux-6.12.1/drivers/media/dvb-frontends/
Dbcm3510.c4 * Copyright (C) 2001-5, B2C2 inc.
8 * This driver is "hard-coded" to be used with the 1st generation of
9 * Technisat/B2C2's Air2PC ATSC PCI/USB cards/boxes. The pll-programming
13 * The driver works also with QAM64 DVB-C, but had an unreasonable high
17 * called "dvb-fe-bcm3510-01.fw".
31 * Ave, Cambridge, MA 02139, USA.
68 MODULE_PARM_DESC(debug, "set debugging level (1=info,2=i2c (|-able)).");
85 …struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = b, .len = len + 1 … in bcm3510_writebytes()
94 if ((err = i2c_transfer (state->i2c, &msg, 1)) != 1) { in bcm3510_writebytes()
97 __func__, state->config->demod_address, reg, err); in bcm3510_writebytes()
[all …]
/linux-6.12.1/drivers/input/touchscreen/
Dmxs-lradc-ts.c1 // SPDX-License-Identifier: GPL-2.0-or-later
19 #include <linux/mfd/mxs-lradc.h>
25 "mxs-lradc-touchscreen",
26 "mxs-lradc-channel6",
27 "mxs-lradc-channel7",
93 return !!(readl(ts->base + LRADC_STATUS) & in mxs_lradc_check_touch_event()
101 ts->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR); in mxs_lradc_map_ts_channel()
103 ts->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET); in mxs_lradc_map_ts_channel()
117 LRADC_CH_NUM_SAMPLES(ts->over_sample_cnt - 1), in mxs_lradc_setup_ts_channel()
118 ts->base + LRADC_CH(ch)); in mxs_lradc_setup_ts_channel()
[all …]
Dstmpe-ts.c1 // SPDX-License-Identifier: GPL-2.0-or-later
46 #define STMPE_TS_NAME "stmpe-ts"
50 * struct stmpe_touch - stmpe811 touch screen controller state
57 * (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
59 * (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us,
60 * 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
63 * (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms,
64 * 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms)
70 * (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max)
106 int_sta = stmpe_reg_read(ts->stmpe, STMPE_REG_INT_STA); in stmpe_work()
[all …]
/linux-6.12.1/drivers/scsi/
Da100u2w.h4 * Copyright (c) 1994-1998 Initio Corporation
19 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
37 * - This and the i60uscsi.h file are almost identical,
40 * - Grand cleanup and Linuxisation
43 #define inia100_REVID "Initio INI-A100U2W SCSI device driver; Revision: 1.02d"
59 /* Scatter-Gather Element Structure */
80 #define ORC_CMD_NOP 0x00 /* Host command - NOP */
81 #define ORC_CMD_VERSION 0x01 /* Host command - Get F/W version */
82 #define ORC_CMD_ECHO 0x02 /* Host command - ECHO */
83 #define ORC_CMD_SET_NVM 0x03 /* Host command - Set NVRAM */
[all …]
/linux-6.12.1/drivers/net/ethernet/cirrus/
Dcs89x0.h1 /* Copyright, 1988-1992, Russell Nelson, Crynwr Software
14 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
18 #define PP_ChipID 0x0000 /* offset 0h -> Corp -ID */
19 /* offset 2h -> Model/Product Number */
20 /* offset 3h -> Chip Revision Number */
50 #define PP_AutoNegCTL 0x011C /* Auto Negotiation Ctrl */
131 /* PP_RxCFG - Receive Configuration and Interrupt Mask bit definition - Read/write */
142 /* PP_RxCTL - Receive Control bit definition - Read/write */
153 /* Default receive mode - individually addressed, broadcast, and error free */
156 /* PP_TxCFG - Transmit Configuration Interrupt Mask bit definition - Read/write */
[all …]
/linux-6.12.1/arch/arm/boot/dts/ti/omap/
Dam5729-beagleboneai.dts1 // SPDX-License-Identifier: GPL-2.0
3 * Copyright (C) 2014-2019 Texas Instruments Incorporated - https://www.ti.com/
6 /dts-v1/;
9 #include "am57xx-commercial-grade.dtsi"
10 #include "dra74x-mmc-iodelay.dtsi"
11 #include "dra74-ipu-dsp-common.dtsi"
12 #include <dt-bindings/gpio/gpio.h>
13 #include <dt-bindings/interrupt-controller/irq.h>
14 #include <dt-bindings/pinctrl/dra.h>
18 compatible = "beagle,am5729-beagleboneai", "ti,am5728",
[all …]
/linux-6.12.1/arch/mips/alchemy/common/
Dirq.c2 * Copyright 2001, 2007-2008 MontaVista Software Inc.
5 * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
25 * 675 Mass Ave, Cambridge, MA 02139, USA.
35 #include <asm/mach-au1x00/au1000.h>
36 #include <asm/mach-au1x00/gpio-au1300.h>
68 /* per-processor fixed function irqs */
83 * the USB devices-side packet complete interrupt (USB_DEV_REQ_INT)
118 { -1, },
151 { -1, },
186 { -1, },
[all …]

12