| /linux-6.12.1/include/linux/ |
| D | signal.h | 110 static inline int sigequalsets(const sigset_t *set1, const sigset_t *set2) in sigequalsets() argument
114 return (set1->sig[3] == set2->sig[3]) && in sigequalsets()
115 (set1->sig[2] == set2->sig[2]) && in sigequalsets()
116 (set1->sig[1] == set2->sig[1]) && in sigequalsets()
117 (set1->sig[0] == set2->sig[0]); in sigequalsets()
119 return (set1->sig[1] == set2->sig[1]) && in sigequalsets()
120 (set1->sig[0] == set2->sig[0]); in sigequalsets()
122 return set1->sig[0] == set2->sig[0]; in sigequalsets()
|
| /linux-6.12.1/include/linux/mfd/ |
| D | max8997.h | 171 * SET1~3 DVS GPIOs control Buck1, 2, and 5 simultaneously. Therefore,
181 int buck125_default_idx; /* Default value of SET1, 2, 3 */
|
| /linux-6.12.1/arch/mips/loongson64/ |
| D | smp.h | 27 #define SET1 0x18 macro
|
| /linux-6.12.1/drivers/net/wireless/ath/ath9k/ |
| D | antenna.c | 95 bool result, set1, set2; in ath_ant_div_comb_alt_check() local
97 result = set1 = set2 = false; in ath_ant_div_comb_alt_check()
101 set1 = true; in ath_ant_div_comb_alt_check()
117 if ((set1 && (alt_rssi_avg >= (main_rssi_avg - 5))) || in ath_ant_div_comb_alt_check()
127 if ((set1 && (alt_rssi_avg >= (main_rssi_avg - 3))) || in ath_ant_div_comb_alt_check()
|
| /linux-6.12.1/drivers/media/i2c/ |
| D | gc0308.c | 663 {CCI_REG8(0x114), 0x44}, /* AWB set1 */
664 {CCI_REG8(0x115), 0x44}, /* AWB set1 */
665 {CCI_REG8(0x116), 0xc2}, /* AWB set1 */
666 {CCI_REG8(0x117), 0xa8}, /* AWB set1 */
667 {CCI_REG8(0x118), 0x18}, /* AWB set1 */
668 {CCI_REG8(0x119), 0x50}, /* AWB set1 */
669 {CCI_REG8(0x11a), 0xd8}, /* AWB set1 */
670 {CCI_REG8(0x11b), 0xf5}, /* AWB set1 */
|
| /linux-6.12.1/Documentation/devicetree/bindings/pci/ |
| D | mediatek-pcie-gen3.yaml | 40 (MSI SET0) (MSI SET1) ... (MSI SET7)
|
| /linux-6.12.1/drivers/regulator/ |
| D | max8997-regulator.c | 53 int set1 = ((max8997->buck125_gpioindex) >> 2) & 0x1; in max8997_set_gpio() local
55 gpiod_set_value(max8997->buck125_gpiods[0], set1); in max8997_set_gpio()
1087 const char *gpio_names[3] = {"MAX8997 SET1", "MAX8997 SET2", "MAX8997 SET3"}; in max8997_pmic_probe()
|
| D | s5m8767.c | 799 "S5M8767 SET1"); in s5m8767_pmic_probe()
813 /* SET1 GPIO */ in s5m8767_pmic_probe()
|
| D | max8998.c | 295 dev_dbg(max8998->dev, "%s: SET1:%d, SET2:%d\n", in max8998_set_voltage_buck_sel()
|
| /linux-6.12.1/drivers/clk/bcm/ |
| D | clk-bcm2835.c | 443 u32 set1; member
453 .set1 = (2 << A2W_PLL_KI_SHIFT) | (8 << A2W_PLL_KP_SHIFT),
463 .set1 = (6 << A2W_PLLH_KP_SHIFT),
710 ana[1] |= data->ana->set1; in bcm2835_pll_set_rate()
|
| /linux-6.12.1/arch/powerpc/boot/dts/ |
| D | turris1x.dts | 358 * CPLD firmware maps SET0, SET1 and SET2
|
| /linux-6.12.1/arch/arm/boot/dts/samsung/ |
| D | exynos5250-spring.dts | 127 s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
|
| /linux-6.12.1/arch/arc/mm/ |
| D | tlb.c | 674 * [set1] | 4 | 5 | 6 | 7 | | 2 | 3 |
|
| /linux-6.12.1/drivers/iio/accel/ |
| D | msa311.c | 1026 "can't disable set0/set1 interrupts\n"); in msa311_chip_init()
|
| /linux-6.12.1/drivers/gpu/drm/panel/ |
| D | panel-sitronix-st7701.c | 43 #define ST7701_CMD2_BK1_SPD1 0xC1 /* Source pre_drive timing set1 */
|
| /linux-6.12.1/drivers/media/pci/bt8xx/ |
| D | bttv-driver.c | 2545 "set0", "set1", "set2", "set3", in bttv_risc_decode()
|
| /linux-6.12.1/drivers/net/ethernet/broadcom/bnx2x/ |
| D | bnx2x_main.c | 4226 BNX2X_ERR("FATAL HW block attention set1 0x%x\n", in bnx2x_attn_int_deasserted1()
|