Searched full:atf (Results 1 – 25 of 38) sorted by relevance
12
| /linux-6.12.1/drivers/pmdomain/amlogic/ |
| D | meson-secure-pwrc.c | 117 /* UART should keep working in ATF after suspend and before resume */
129 /* SRAMB is used as ATF runtime memory, and should be always on */
215 /* SRAMA is used as ATF runtime memory, and should be always on */
217 /* SRAMB is used as ATF runtime memory, and should be always on */
|
| /linux-6.12.1/drivers/net/ethernet/marvell/octeontx2/af/ |
| D | lmac_common.h | 63 /* For ATF to send events to kernel, there is no dedicated interrupt
65 * SW_INT so that ATF triggers this interrupt after processing of
|
| D | cgx_fw_if.h | 163 /* scratchx(0) CSR used for ATF->non-secure SW communication.
236 /* scratchx(1) CSR used for non-secure SW->ATF communication
|
| /linux-6.12.1/arch/arm64/boot/dts/airoha/ |
| D | en7581-evb.dts | 4 /* Bootloader installs ATF here */
|
| /linux-6.12.1/arch/arm/boot/dts/airoha/ |
| D | en7523-evb.dts | 4 /* Bootloader installs ATF here */
|
| /linux-6.12.1/Documentation/devicetree/bindings/watchdog/ |
| D | arm-smc-wdt.yaml | 23 The ATF smc function id used by the firmware.
|
| /linux-6.12.1/drivers/clk/zynqmp/ |
| D | pll.c | 17 * @set_pll_mode: Whether an IOCTL_SET_PLL_FRAC_MODE request be sent to ATF
258 * that has been sent to ATF. in zynqmp_pll_enable()
|
| /linux-6.12.1/include/dt-bindings/clock/ |
| D | rk3399-ddr.h | 53 /* DDR3 ATF default */
|
| /linux-6.12.1/arch/arm/boot/dts/st/ |
| D | stm32mp157c-odyssey.dts | 41 assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */
|
| D | stm32mp15xc-lxa-tac.dtsi | 230 assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
|
| /linux-6.12.1/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-sm-k26-revA.dts | 183 label = "Image A (FSBL, PMU, ATF, U-Boot)";
193 label = "Image B (FSBL, PMU, ATF, U-Boot)";
|
| /linux-6.12.1/drivers/net/can/flexcan/ |
| D | flexcan.h | 71 /* Setup stop mode with ATF SCMI protocol to support wakeup */
|
| D | flexcan-core.c | 556 /* For the SCMI mode, driver do nothing, ATF will send request to in flexcan_enter_stop_mode()
574 * do nothing here, because ATF already send request to SM before in flexcan_exit_stop_mode()
2006 /* ATF will handle all STOP_IPG related work */ in flexcan_setup_stop_mode()
2335 /* For FLEXCAN_QUIRK_SETUP_STOP_MODE_SCMI, it need ATF to send in flexcan_noirq_suspend()
|
| /linux-6.12.1/Documentation/devicetree/bindings/firmware/ |
| D | fsl,scu.yaml | 58 execution environments such as ATF.
|
| /linux-6.12.1/drivers/soc/imx/ |
| D | soc-imx8m.c | 78 * the value from ATF instead. in imx8mq_soc_revision()
|
| /linux-6.12.1/include/linux/firmware/ |
| D | xlnx-zynqmp.h | 58 /* ATF only commands */
216 /* Register SGI to ATF */
|
| /linux-6.12.1/drivers/net/ethernet/broadcom/ |
| D | bgmac-platform.c | 87 /* Some bits of BCMA_IOCTL set by HW/ATF and should not change */ in platform_bgmac_clk_enable()
|
| /linux-6.12.1/drivers/clk/mediatek/ |
| D | clk-mt8195-infra_ao.c | 143 /* pwrmcu is used by ATF for platform PM: clocks must never be disabled by the kernel */
|
| /linux-6.12.1/drivers/clocksource/ |
| D | timer-mediatek.c | 265 * or for example ATF will prevent a suspend from completing. in mtk_gpt_suspend()
|
| /linux-6.12.1/arch/arm64/boot/dts/broadcom/ |
| D | bcm2712.dtsi | 175 atf@0 {
|
| /linux-6.12.1/Documentation/ABI/testing/ |
| D | sysfs-bus-platform-devices-ampere-smpro | 292 - 02: ATF BL1 firmware booting
295 - 05: ATF BL2 firmware booting
296 - 06: ATF BL31 firmware booting
297 - 07: ATF BL32 firmware booting
|
| /linux-6.12.1/arch/arm64/boot/dts/ti/ |
| D | k3-j7200-common-proc-board.dts | 280 /* Shared with ATF on this platform */
|
| D | k3-j721e-common-proc-board.dts | 450 /* Shared with ATF on this platform */
|
| /linux-6.12.1/drivers/clk/mvebu/ |
| D | armada-37xx-periph.c | 712 /* Follow the same order than what the Cortex-M3 does (ATF code) */ in armada_3700_periph_clock_resume()
|
| /linux-6.12.1/drivers/platform/mellanox/ |
| D | mlxbf-bootctl.c | 27 /* UUID used to probe ATF service. */
|
12