1 /* SPDX-License-Identifier: GPL-2.0-only */
2 /*
3 * driver.h -- SoC Regulator driver support.
4 *
5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
6 *
7 * Author: Liam Girdwood <lrg@slimlogic.co.uk>
8 *
9 * Regulator Driver Interface.
10 */
11
12 #ifndef __LINUX_REGULATOR_DRIVER_H_
13 #define __LINUX_REGULATOR_DRIVER_H_
14
15 #include <linux/device.h>
16 #include <linux/linear_range.h>
17 #include <linux/notifier.h>
18 #include <linux/regulator/consumer.h>
19 #include <linux/ww_mutex.h>
20
21 struct gpio_desc;
22 struct regmap;
23 struct regulator_dev;
24 struct regulator_config;
25 struct regulator_init_data;
26 struct regulator_enable_gpio;
27
28 enum regulator_status {
29 REGULATOR_STATUS_OFF,
30 REGULATOR_STATUS_ON,
31 REGULATOR_STATUS_ERROR,
32 /* fast/normal/idle/standby are flavors of "on" */
33 REGULATOR_STATUS_FAST,
34 REGULATOR_STATUS_NORMAL,
35 REGULATOR_STATUS_IDLE,
36 REGULATOR_STATUS_STANDBY,
37 /* The regulator is enabled but not regulating */
38 REGULATOR_STATUS_BYPASS,
39 /* in case that any other status doesn't apply */
40 REGULATOR_STATUS_UNDEFINED,
41 };
42
43 enum regulator_detection_severity {
44 /* Hardware shut down voltage outputs if condition is detected */
45 REGULATOR_SEVERITY_PROT,
46 /* Hardware is probably damaged/inoperable */
47 REGULATOR_SEVERITY_ERR,
48 /* Hardware is still recoverable but recovery action must be taken */
49 REGULATOR_SEVERITY_WARN,
50 };
51
52 /* Initialize struct linear_range for regulators */
53 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \
54 LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV)
55
56 /**
57 * struct regulator_ops - regulator operations.
58 *
59 * @enable: Configure the regulator as enabled.
60 * @disable: Configure the regulator as disabled.
61 * @is_enabled: Return 1 if the regulator is enabled, 0 if not.
62 * May also return negative errno.
63 *
64 * @set_voltage: Set the voltage for the regulator within the range specified.
65 * The driver should select the voltage closest to min_uV.
66 * @set_voltage_sel: Set the voltage for the regulator using the specified
67 * selector.
68 * @map_voltage: Convert a voltage into a selector
69 * @get_voltage: Return the currently configured voltage for the regulator;
70 * return -ENOTRECOVERABLE if regulator can't be read at
71 * bootup and hasn't been set yet.
72 * @get_voltage_sel: Return the currently configured voltage selector for the
73 * regulator; return -ENOTRECOVERABLE if regulator can't
74 * be read at bootup and hasn't been set yet.
75 * @list_voltage: Return one of the supported voltages, in microvolts; zero
76 * if the selector indicates a voltage that is unusable on this system;
77 * or negative errno. Selectors range from zero to one less than
78 * regulator_desc.n_voltages. Voltages may be reported in any order.
79 *
80 * @set_current_limit: Configure a limit for a current-limited regulator.
81 * The driver should select the current closest to max_uA.
82 * @get_current_limit: Get the configured limit for a current-limited regulator.
83 * @set_input_current_limit: Configure an input limit.
84 *
85 * @set_over_current_protection: Support enabling of and setting limits for over
86 * current situation detection. Detection can be configured for three
87 * levels of severity.
88 *
89 * - REGULATOR_SEVERITY_PROT should automatically shut down the regulator(s).
90 *
91 * - REGULATOR_SEVERITY_ERR should indicate that over-current situation is
92 * caused by an unrecoverable error but HW does not perform
93 * automatic shut down.
94 *
95 * - REGULATOR_SEVERITY_WARN should indicate situation where hardware is
96 * still believed to not be damaged but that a board sepcific
97 * recovery action is needed. If lim_uA is 0 the limit should not
98 * be changed but the detection should just be enabled/disabled as
99 * is requested.
100 *
101 * @set_over_voltage_protection: Support enabling of and setting limits for over
102 * voltage situation detection. Detection can be configured for same
103 * severities as over current protection. Units of uV.
104 * @set_under_voltage_protection: Support enabling of and setting limits for
105 * under voltage situation detection. Detection can be configured for same
106 * severities as over current protection. Units of uV.
107 * @set_thermal_protection: Support enabling of and setting limits for over
108 * temperature situation detection.Detection can be configured for same
109 * severities as over current protection. Units of degree Kelvin.
110 *
111 * @set_active_discharge: Set active discharge enable/disable of regulators.
112 *
113 * @set_mode: Set the configured operating mode for the regulator.
114 * @get_mode: Get the configured operating mode for the regulator.
115 * @get_error_flags: Get the current error(s) for the regulator.
116 * @get_status: Return actual (not as-configured) status of regulator, as a
117 * REGULATOR_STATUS value (or negative errno)
118 * @get_optimum_mode: Get the most efficient operating mode for the regulator
119 * when running with the specified parameters.
120 * @set_load: Set the load for the regulator.
121 *
122 * @set_bypass: Set the regulator in bypass mode.
123 * @get_bypass: Get the regulator bypass mode state.
124 *
125 * @enable_time: Time taken for the regulator voltage output voltage to
126 * stabilise after being enabled, in microseconds.
127 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should
128 * select ramp delay equal to or less than(closest) ramp_delay.
129 * @set_voltage_time: Time taken for the regulator voltage output voltage
130 * to stabilise after being set to a new value, in microseconds.
131 * The function receives the from and to voltage as input, it
132 * should return the worst case.
133 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage
134 * to stabilise after being set to a new value, in microseconds.
135 * The function receives the from and to voltage selector as
136 * input, it should return the worst case.
137 * @set_soft_start: Enable soft start for the regulator.
138 *
139 * @set_suspend_voltage: Set the voltage for the regulator when the system
140 * is suspended.
141 * @set_suspend_enable: Mark the regulator as enabled when the system is
142 * suspended.
143 * @set_suspend_disable: Mark the regulator as disabled when the system is
144 * suspended.
145 * @set_suspend_mode: Set the operating mode for the regulator when the
146 * system is suspended.
147 * @resume: Resume operation of suspended regulator.
148 * @set_pull_down: Configure the regulator to pull down when the regulator
149 * is disabled.
150 *
151 * This struct describes regulator operations which can be implemented by
152 * regulator chip drivers.
153 */
154 struct regulator_ops {
155
156 /* enumerate supported voltages */
157 int (*list_voltage) (struct regulator_dev *, unsigned selector);
158
159 /* get/set regulator voltage */
160 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV,
161 unsigned *selector);
162 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV);
163 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector);
164 int (*get_voltage) (struct regulator_dev *);
165 int (*get_voltage_sel) (struct regulator_dev *);
166
167 /* get/set regulator current */
168 int (*set_current_limit) (struct regulator_dev *,
169 int min_uA, int max_uA);
170 int (*get_current_limit) (struct regulator_dev *);
171
172 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
173 int (*set_over_current_protection)(struct regulator_dev *, int lim_uA,
174 int severity, bool enable);
175 int (*set_over_voltage_protection)(struct regulator_dev *, int lim_uV,
176 int severity, bool enable);
177 int (*set_under_voltage_protection)(struct regulator_dev *, int lim_uV,
178 int severity, bool enable);
179 int (*set_thermal_protection)(struct regulator_dev *, int lim,
180 int severity, bool enable);
181 int (*set_active_discharge)(struct regulator_dev *, bool enable);
182
183 /* enable/disable regulator */
184 int (*enable) (struct regulator_dev *);
185 int (*disable) (struct regulator_dev *);
186 int (*is_enabled) (struct regulator_dev *);
187
188 /* get/set regulator operating mode (defined in consumer.h) */
189 int (*set_mode) (struct regulator_dev *, unsigned int mode);
190 unsigned int (*get_mode) (struct regulator_dev *);
191
192 /* retrieve current error flags on the regulator */
193 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags);
194
195 /* Time taken to enable or set voltage on the regulator */
196 int (*enable_time) (struct regulator_dev *);
197 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay);
198 int (*set_voltage_time) (struct regulator_dev *, int old_uV,
199 int new_uV);
200 int (*set_voltage_time_sel) (struct regulator_dev *,
201 unsigned int old_selector,
202 unsigned int new_selector);
203
204 int (*set_soft_start) (struct regulator_dev *);
205
206 /* report regulator status ... most other accessors report
207 * control inputs, this reports results of combining inputs
208 * from Linux (and other sources) with the actual load.
209 * returns REGULATOR_STATUS_* or negative errno.
210 */
211 int (*get_status)(struct regulator_dev *);
212
213 /* get most efficient regulator operating mode for load */
214 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV,
215 int output_uV, int load_uA);
216 /* set the load on the regulator */
217 int (*set_load)(struct regulator_dev *, int load_uA);
218
219 /* control and report on bypass mode */
220 int (*set_bypass)(struct regulator_dev *dev, bool enable);
221 int (*get_bypass)(struct regulator_dev *dev, bool *enable);
222
223 /* the operations below are for configuration of regulator state when
224 * its parent PMIC enters a global STANDBY/HIBERNATE state */
225
226 /* set regulator suspend voltage */
227 int (*set_suspend_voltage) (struct regulator_dev *, int uV);
228
229 /* enable/disable regulator in suspend state */
230 int (*set_suspend_enable) (struct regulator_dev *);
231 int (*set_suspend_disable) (struct regulator_dev *);
232
233 /* set regulator suspend operating mode (defined in consumer.h) */
234 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode);
235
236 int (*resume)(struct regulator_dev *rdev);
237
238 int (*set_pull_down) (struct regulator_dev *);
239 };
240
241 /*
242 * Regulators can either control voltage or current.
243 */
244 enum regulator_type {
245 REGULATOR_VOLTAGE,
246 REGULATOR_CURRENT,
247 };
248
249 /**
250 * struct regulator_desc - Static regulator descriptor
251 *
252 * Each regulator registered with the core is described with a
253 * structure of this type and a struct regulator_config. This
254 * structure contains the non-varying parts of the regulator
255 * description.
256 *
257 * @name: Identifying name for the regulator.
258 * @supply_name: Identifying the regulator supply
259 * @of_match: Name used to identify regulator in DT.
260 * @of_match_full_name: A flag to indicate that the of_match string, if
261 * present, should be matched against the node full_name.
262 * @regulators_node: Name of node containing regulator definitions in DT.
263 * @of_parse_cb: Optional callback called only if of_match is present.
264 * Will be called for each regulator parsed from DT, during
265 * init_data parsing.
266 * The regulator_config passed as argument to the callback will
267 * be a copy of config passed to regulator_register, valid only
268 * for this particular call. Callback may freely change the
269 * config but it cannot store it for later usage.
270 * Callback should return 0 on success or negative ERRNO
271 * indicating failure.
272 * @id: Numerical identifier for the regulator.
273 * @ops: Regulator operations table.
274 * @irq: Interrupt number for the regulator.
275 * @type: Indicates if the regulator is a voltage or current regulator.
276 * @owner: Module providing the regulator, used for refcounting.
277 *
278 * @continuous_voltage_range: Indicates if the regulator can set any
279 * voltage within constrains range.
280 * @n_voltages: Number of selectors available for ops.list_voltage().
281 * @n_current_limits: Number of selectors available for current limits
282 *
283 * @min_uV: Voltage given by the lowest selector (if linear mapping)
284 * @uV_step: Voltage increase with each selector (if linear mapping)
285 * @linear_min_sel: Minimal selector for starting linear mapping
286 * @fixed_uV: Fixed voltage of rails.
287 * @ramp_delay: Time to settle down after voltage change (unit: uV/us)
288 * @min_dropout_uV: The minimum dropout voltage this regulator can handle
289 * @linear_ranges: A constant table of possible voltage ranges.
290 * @linear_range_selectors_bitfield: A constant table of voltage range
291 * selectors as bitfield values. If
292 * pickable ranges are used each range
293 * must have corresponding selector here.
294 * @n_linear_ranges: Number of entries in the @linear_ranges (and in
295 * linear_range_selectors_bitfield if used) table(s).
296 * @volt_table: Voltage mapping table (if table based mapping)
297 * @curr_table: Current limit mapping table (if table based mapping)
298 *
299 * @vsel_range_reg: Register for range selector when using pickable ranges
300 * and ``regulator_map_*_voltage_*_pickable`` functions.
301 * @vsel_range_mask: Mask for register bitfield used for range selector
302 * @range_applied_by_vsel: A flag to indicate that changes to vsel_range_reg
303 * are only effective after vsel_reg is written
304 * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*``
305 * @vsel_mask: Mask for register bitfield used for selector
306 * @vsel_step: Specify the resolution of selector stepping when setting
307 * voltage. If 0, then no stepping is done (requested selector is
308 * set directly), if >0 then the regulator API will ramp the
309 * voltage up/down gradually each time increasing/decreasing the
310 * selector by the specified step value.
311 * @csel_reg: Register for current limit selector using regmap set_current_limit
312 * @csel_mask: Mask for register bitfield used for current limit selector
313 * @apply_reg: Register for initiate voltage change on the output when
314 * using regulator_set_voltage_sel_regmap
315 * @apply_bit: Register bitfield used for initiate voltage change on the
316 * output when using regulator_set_voltage_sel_regmap
317 * @enable_reg: Register for control when using regmap enable/disable ops
318 * @enable_mask: Mask for control when using regmap enable/disable ops
319 * @enable_val: Enabling value for control when using regmap enable/disable ops
320 * @disable_val: Disabling value for control when using regmap enable/disable ops
321 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable
322 * when using regulator_enable_regmap and friends APIs.
323 * @bypass_reg: Register for control when using regmap set_bypass
324 * @bypass_mask: Mask for control when using regmap set_bypass
325 * @bypass_val_on: Enabling value for control when using regmap set_bypass
326 * @bypass_val_off: Disabling value for control when using regmap set_bypass
327 * @active_discharge_off: Enabling value for control when using regmap
328 * set_active_discharge
329 * @active_discharge_on: Disabling value for control when using regmap
330 * set_active_discharge
331 * @active_discharge_mask: Mask for control when using regmap
332 * set_active_discharge
333 * @active_discharge_reg: Register for control when using regmap
334 * set_active_discharge
335 * @soft_start_reg: Register for control when using regmap set_soft_start
336 * @soft_start_mask: Mask for control when using regmap set_soft_start
337 * @soft_start_val_on: Enabling value for control when using regmap
338 * set_soft_start
339 * @pull_down_reg: Register for control when using regmap set_pull_down
340 * @pull_down_mask: Mask for control when using regmap set_pull_down
341 * @pull_down_val_on: Enabling value for control when using regmap
342 * set_pull_down
343 *
344 * @ramp_reg: Register for controlling the regulator ramp-rate.
345 * @ramp_mask: Bitmask for the ramp-rate control register.
346 * @ramp_delay_table: Table for mapping the regulator ramp-rate values. Values
347 * should be given in units of V/S (uV/uS). See the
348 * regulator_set_ramp_delay_regmap().
349 * @n_ramp_values: number of elements at @ramp_delay_table.
350 *
351 * @enable_time: Time taken for initial enable of regulator (in uS).
352 * @off_on_delay: guard time (in uS), before re-enabling a regulator
353 *
354 * @poll_enabled_time: The polling interval (in uS) to use while checking that
355 * the regulator was actually enabled. Max upto enable_time.
356 *
357 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode
358 */
359 struct regulator_desc {
360 const char *name;
361 const char *supply_name;
362 const char *of_match;
363 bool of_match_full_name;
364 const char *regulators_node;
365 int (*of_parse_cb)(struct device_node *,
366 const struct regulator_desc *,
367 struct regulator_config *);
368 int id;
369 unsigned int continuous_voltage_range:1;
370 unsigned n_voltages;
371 unsigned int n_current_limits;
372 const struct regulator_ops *ops;
373 int irq;
374 enum regulator_type type;
375 struct module *owner;
376
377 unsigned int min_uV;
378 unsigned int uV_step;
379 unsigned int linear_min_sel;
380 int fixed_uV;
381 unsigned int ramp_delay;
382 int min_dropout_uV;
383
384 const struct linear_range *linear_ranges;
385 const unsigned int *linear_range_selectors_bitfield;
386
387 int n_linear_ranges;
388
389 const unsigned int *volt_table;
390 const unsigned int *curr_table;
391
392 unsigned int vsel_range_reg;
393 unsigned int vsel_range_mask;
394 bool range_applied_by_vsel;
395 unsigned int vsel_reg;
396 unsigned int vsel_mask;
397 unsigned int vsel_step;
398 unsigned int csel_reg;
399 unsigned int csel_mask;
400 unsigned int apply_reg;
401 unsigned int apply_bit;
402 unsigned int enable_reg;
403 unsigned int enable_mask;
404 unsigned int enable_val;
405 unsigned int disable_val;
406 bool enable_is_inverted;
407 unsigned int bypass_reg;
408 unsigned int bypass_mask;
409 unsigned int bypass_val_on;
410 unsigned int bypass_val_off;
411 unsigned int active_discharge_on;
412 unsigned int active_discharge_off;
413 unsigned int active_discharge_mask;
414 unsigned int active_discharge_reg;
415 unsigned int soft_start_reg;
416 unsigned int soft_start_mask;
417 unsigned int soft_start_val_on;
418 unsigned int pull_down_reg;
419 unsigned int pull_down_mask;
420 unsigned int pull_down_val_on;
421 unsigned int ramp_reg;
422 unsigned int ramp_mask;
423 const unsigned int *ramp_delay_table;
424 unsigned int n_ramp_values;
425
426 unsigned int enable_time;
427
428 unsigned int off_on_delay;
429
430 unsigned int poll_enabled_time;
431
432 unsigned int (*of_map_mode)(unsigned int mode);
433 };
434
435 /**
436 * struct regulator_config - Dynamic regulator descriptor
437 *
438 * Each regulator registered with the core is described with a
439 * structure of this type and a struct regulator_desc. This structure
440 * contains the runtime variable parts of the regulator description.
441 *
442 * @dev: struct device for the regulator
443 * @init_data: platform provided init data, passed through by driver
444 * @driver_data: private regulator data
445 * @of_node: OpenFirmware node to parse for device tree bindings (may be
446 * NULL).
447 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is
448 * insufficient.
449 * @ena_gpiod: GPIO controlling regulator enable.
450 */
451 struct regulator_config {
452 struct device *dev;
453 const struct regulator_init_data *init_data;
454 void *driver_data;
455 struct device_node *of_node;
456 struct regmap *regmap;
457
458 struct gpio_desc *ena_gpiod;
459 };
460
461 /**
462 * struct regulator_err_state - regulator error/notification status
463 *
464 * @rdev: Regulator which status the struct indicates.
465 * @notifs: Events which have occurred on the regulator.
466 * @errors: Errors which are active on the regulator.
467 * @possible_errs: Errors which can be signaled (by given IRQ).
468 */
469 struct regulator_err_state {
470 struct regulator_dev *rdev;
471 unsigned long notifs;
472 unsigned long errors;
473 int possible_errs;
474 };
475
476 /**
477 * struct regulator_irq_data - regulator error/notification status data
478 *
479 * @states: Status structs for each of the associated regulators.
480 * @num_states: Amount of associated regulators.
481 * @data: Driver data pointer given at regulator_irq_desc.
482 * @opaque: Value storage for IC driver. Core does not update this. ICs
483 * may want to store status register value here at map_event and
484 * compare contents at 'renable' callback to see if new problems
485 * have been added to status. If that is the case it may be
486 * desirable to return REGULATOR_ERROR_CLEARED and not
487 * REGULATOR_ERROR_ON to allow IRQ fire again and to generate
488 * notifications also for the new issues.
489 *
490 * This structure is passed to 'map_event' and 'renable' callbacks for
491 * reporting regulator status to core.
492 */
493 struct regulator_irq_data {
494 struct regulator_err_state *states;
495 int num_states;
496 void *data;
497 long opaque;
498 };
499
500 /**
501 * struct regulator_irq_desc - notification sender for IRQ based events.
502 *
503 * @name: The visible name for the IRQ
504 * @fatal_cnt: If this IRQ is used to signal HW damaging condition it may be
505 * best to shut-down regulator(s) or reboot the SOC if error
506 * handling is repeatedly failing. If fatal_cnt is given the IRQ
507 * handling is aborted if it fails for fatal_cnt times and die()
508 * callback (if populated) is called. If die() is not populated
509 * poweroff for the system is attempted in order to prevent any
510 * further damage.
511 * @reread_ms: The time which is waited before attempting to re-read status
512 * at the worker if IC reading fails. Immediate re-read is done
513 * if time is not specified.
514 * @irq_off_ms: The time which IRQ is kept disabled before re-evaluating the
515 * status for devices which keep IRQ disabled for duration of the
516 * error. If this is not given the IRQ is left enabled and renable
517 * is not called.
518 * @skip_off: If set to true the IRQ handler will attempt to check if any of
519 * the associated regulators are enabled prior to taking other
520 * actions. If no regulators are enabled and this is set to true
521 * a spurious IRQ is assumed and IRQ_NONE is returned.
522 * @high_prio: Boolean to indicate that high priority WQ should be used.
523 * @data: Driver private data pointer which will be passed as such to
524 * the renable, map_event and die callbacks in regulator_irq_data.
525 * @die: Protection callback. If IC status reading or recovery actions
526 * fail fatal_cnt times this callback is called or system is
527 * powered off. This callback should implement a final protection
528 * attempt like disabling the regulator. If protection succeeded
529 * die() may return 0. If anything else is returned the core
530 * assumes final protection failed and attempts to perform a
531 * poweroff as a last resort.
532 * @map_event: Driver callback to map IRQ status into regulator devices with
533 * events / errors. NOTE: callback MUST initialize both the
534 * errors and notifs for all rdevs which it signals having
535 * active events as core does not clean the map data.
536 * REGULATOR_FAILED_RETRY can be returned to indicate that the
537 * status reading from IC failed. If this is repeated for
538 * fatal_cnt times the core will call die() callback or power-off
539 * the system as a last resort to protect the HW.
540 * @renable: Optional callback to check status (if HW supports that) before
541 * re-enabling IRQ. If implemented this should clear the error
542 * flags so that errors fetched by regulator_get_error_flags()
543 * are updated. If callback is not implemented then errors are
544 * assumed to be cleared and IRQ is re-enabled.
545 * REGULATOR_FAILED_RETRY can be returned to
546 * indicate that the status reading from IC failed. If this is
547 * repeated for 'fatal_cnt' times the core will call die()
548 * callback or if die() is not populated then attempt to power-off
549 * the system as a last resort to protect the HW.
550 * Returning zero indicates that the problem in HW has been solved
551 * and IRQ will be re-enabled. Returning REGULATOR_ERROR_ON
552 * indicates the error condition is still active and keeps IRQ
553 * disabled. Please note that returning REGULATOR_ERROR_ON does
554 * not retrigger evaluating what events are active or resending
555 * notifications. If this is needed you probably want to return
556 * zero and allow IRQ to retrigger causing events to be
557 * re-evaluated and re-sent.
558 *
559 * This structure is used for registering regulator IRQ notification helper.
560 */
561 struct regulator_irq_desc {
562 const char *name;
563 int fatal_cnt;
564 int reread_ms;
565 int irq_off_ms;
566 bool skip_off;
567 bool high_prio;
568 void *data;
569
570 int (*die)(struct regulator_irq_data *rid);
571 int (*map_event)(int irq, struct regulator_irq_data *rid,
572 unsigned long *dev_mask);
573 int (*renable)(struct regulator_irq_data *rid);
574 };
575
576 /*
577 * Return values for regulator IRQ helpers.
578 */
579 enum {
580 REGULATOR_ERROR_CLEARED,
581 REGULATOR_FAILED_RETRY,
582 REGULATOR_ERROR_ON,
583 };
584
585 /*
586 * struct coupling_desc
587 *
588 * Describes coupling of regulators. Each regulator should have
589 * at least a pointer to itself in coupled_rdevs array.
590 * When a new coupled regulator is resolved, n_resolved is
591 * incremented.
592 */
593 struct coupling_desc {
594 struct regulator_dev **coupled_rdevs;
595 struct regulator_coupler *coupler;
596 int n_resolved;
597 int n_coupled;
598 };
599
600 /*
601 * struct regulator_dev
602 *
603 * Voltage / Current regulator class device. One for each
604 * regulator.
605 *
606 * This should *not* be used directly by anything except the regulator
607 * core and notification injection (which should take the mutex and do
608 * no other direct access).
609 */
610 struct regulator_dev {
611 const struct regulator_desc *desc;
612 int exclusive;
613 u32 use_count;
614 u32 open_count;
615 u32 bypass_count;
616
617 /* lists we belong to */
618 struct list_head list; /* list of all regulators */
619
620 /* lists we own */
621 struct list_head consumer_list; /* consumers we supply */
622
623 struct coupling_desc coupling_desc;
624
625 struct blocking_notifier_head notifier;
626 struct ww_mutex mutex; /* consumer lock */
627 struct task_struct *mutex_owner;
628 int ref_cnt;
629 struct module *owner;
630 struct device dev;
631 struct regulation_constraints *constraints;
632 struct regulator *supply; /* for tree */
633 const char *supply_name;
634 struct regmap *regmap;
635
636 struct delayed_work disable_work;
637
638 void *reg_data; /* regulator_dev data */
639
640 struct dentry *debugfs;
641
642 struct regulator_enable_gpio *ena_pin;
643 unsigned int ena_gpio_state:1;
644
645 unsigned int is_switch:1;
646
647 /* time when this regulator was disabled last time */
648 ktime_t last_off;
649 int cached_err;
650 bool use_cached_err;
651 spinlock_t err_lock;
652 };
653
654 /*
655 * Convert error flags to corresponding notifications.
656 *
657 * Can be used by drivers which use the notification helpers to
658 * find out correct notification flags based on the error flags. Drivers
659 * can avoid storing both supported notification and error flags which
660 * may save few bytes.
661 */
regulator_err2notif(int err)662 static inline int regulator_err2notif(int err)
663 {
664 switch (err) {
665 case REGULATOR_ERROR_UNDER_VOLTAGE:
666 return REGULATOR_EVENT_UNDER_VOLTAGE;
667 case REGULATOR_ERROR_OVER_CURRENT:
668 return REGULATOR_EVENT_OVER_CURRENT;
669 case REGULATOR_ERROR_REGULATION_OUT:
670 return REGULATOR_EVENT_REGULATION_OUT;
671 case REGULATOR_ERROR_FAIL:
672 return REGULATOR_EVENT_FAIL;
673 case REGULATOR_ERROR_OVER_TEMP:
674 return REGULATOR_EVENT_OVER_TEMP;
675 case REGULATOR_ERROR_UNDER_VOLTAGE_WARN:
676 return REGULATOR_EVENT_UNDER_VOLTAGE_WARN;
677 case REGULATOR_ERROR_OVER_CURRENT_WARN:
678 return REGULATOR_EVENT_OVER_CURRENT_WARN;
679 case REGULATOR_ERROR_OVER_VOLTAGE_WARN:
680 return REGULATOR_EVENT_OVER_VOLTAGE_WARN;
681 case REGULATOR_ERROR_OVER_TEMP_WARN:
682 return REGULATOR_EVENT_OVER_TEMP_WARN;
683 }
684 return 0;
685 }
686
687
688 struct regulator_dev *
689 regulator_register(struct device *dev,
690 const struct regulator_desc *regulator_desc,
691 const struct regulator_config *config);
692 struct regulator_dev *
693 devm_regulator_register(struct device *dev,
694 const struct regulator_desc *regulator_desc,
695 const struct regulator_config *config);
696 void regulator_unregister(struct regulator_dev *rdev);
697
698 int regulator_notifier_call_chain(struct regulator_dev *rdev,
699 unsigned long event, void *data);
700 void *devm_regulator_irq_helper(struct device *dev,
701 const struct regulator_irq_desc *d, int irq,
702 int irq_flags, int common_errs,
703 int *per_rdev_errs, struct regulator_dev **rdev,
704 int rdev_amount);
705 void *regulator_irq_helper(struct device *dev,
706 const struct regulator_irq_desc *d, int irq,
707 int irq_flags, int common_errs, int *per_rdev_errs,
708 struct regulator_dev **rdev, int rdev_amount);
709 void regulator_irq_helper_cancel(void **handle);
710 int regulator_irq_map_event_simple(int irq, struct regulator_irq_data *rid,
711 unsigned long *dev_mask);
712
713 void *rdev_get_drvdata(struct regulator_dev *rdev);
714 struct device *rdev_get_dev(struct regulator_dev *rdev);
715 struct regmap *rdev_get_regmap(struct regulator_dev *rdev);
716 int rdev_get_id(struct regulator_dev *rdev);
717
718 int regulator_mode_to_status(unsigned int);
719
720 int regulator_list_voltage_linear(struct regulator_dev *rdev,
721 unsigned int selector);
722 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev,
723 unsigned int selector);
724 int regulator_list_voltage_linear_range(struct regulator_dev *rdev,
725 unsigned int selector);
726 int regulator_list_voltage_table(struct regulator_dev *rdev,
727 unsigned int selector);
728 int regulator_map_voltage_linear(struct regulator_dev *rdev,
729 int min_uV, int max_uV);
730 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev,
731 int min_uV, int max_uV);
732 int regulator_map_voltage_linear_range(struct regulator_dev *rdev,
733 int min_uV, int max_uV);
734 int regulator_map_voltage_iterate(struct regulator_dev *rdev,
735 int min_uV, int max_uV);
736 int regulator_map_voltage_ascend(struct regulator_dev *rdev,
737 int min_uV, int max_uV);
738 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev);
739 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev,
740 unsigned int sel);
741 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev);
742 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel);
743 int regulator_is_enabled_regmap(struct regulator_dev *rdev);
744 int regulator_enable_regmap(struct regulator_dev *rdev);
745 int regulator_disable_regmap(struct regulator_dev *rdev);
746 int regulator_set_voltage_time_sel(struct regulator_dev *rdev,
747 unsigned int old_selector,
748 unsigned int new_selector);
749 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable);
750 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable);
751 int regulator_set_soft_start_regmap(struct regulator_dev *rdev);
752 int regulator_set_pull_down_regmap(struct regulator_dev *rdev);
753
754 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
755 bool enable);
756 int regulator_set_current_limit_regmap(struct regulator_dev *rdev,
757 int min_uA, int max_uA);
758 int regulator_get_current_limit_regmap(struct regulator_dev *rdev);
759 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
760 int regulator_find_closest_bigger(unsigned int target, const unsigned int *table,
761 unsigned int num_sel, unsigned int *sel);
762 int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay);
763 int regulator_sync_voltage_rdev(struct regulator_dev *rdev);
764
765 /*
766 * Helper functions intended to be used by regulator drivers prior registering
767 * their regulators.
768 */
769 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc,
770 unsigned int selector);
771
772 int regulator_desc_list_voltage_linear(const struct regulator_desc *desc,
773 unsigned int selector);
774
775 #ifdef CONFIG_REGULATOR
776 const char *rdev_get_name(struct regulator_dev *rdev);
777 #else
rdev_get_name(struct regulator_dev * rdev)778 static inline const char *rdev_get_name(struct regulator_dev *rdev)
779 {
780 return NULL;
781 }
782 #endif
783
784 #endif
785