/* * Copyright (c) 2012-2021 The Linux Foundation. All rights reserved. * Copyright (c) 2021-2024 Qualcomm Innovation Center, Inc. All rights reserved. * * Permission to use, copy, modify, and/or distribute this software for * any purpose with or without fee is hereby granted, provided that the * above copyright notice and this permission notice appear in all * copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL * WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE * AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL * DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR * PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR * PERFORMANCE OF THIS SOFTWARE. */ /** * DOC: declares vendor commands interfacing with linux kernel */ #ifndef _WLAN_QCA_VENDOR_H_ #define _WLAN_QCA_VENDOR_H_ /* Vendor id to be used in vendor specific command and events * to user space. * NOTE: The authoritative place for definition of QCA_NL80211_VENDOR_ID, * vendor subcmd definitions prefixed with QCA_NL80211_VENDOR_SUBCMD, and * qca_wlan_vendor_attr is open source file src/common/qca-vendor.h in * git://w1.fi/srv/git/hostap.git; the values here are just a copy of that */ #define QCA_NL80211_VENDOR_ID 0x001374 #ifndef BIT #define BIT(x) (1U << (x)) #endif /** * enum qca_nl80211_vendor_subcmds: NL 80211 vendor sub command * * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Unspecified * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test * Sub commands 2 to 8 are not used * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Roaming * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Avoid frequency. * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: DFS capability * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass * NAN Request/Response and NAN Indication messages. These messages are * interpreted between the framework and the firmware component. While * sending the command from userspace to the driver, payload is not * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN * is used when receiving vendor events in userspace from the driver. * @QCA_NL80211_VENDOR_SUBCMD_STATS_EXT: Ext stats * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET: Link layer stats set * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET: Link layer stats get * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR: Link layer stats clear * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS: Link layer stats radio * results * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS: Link layer stats interface * results * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS: Link layer stats peer * results * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START: Ext scan start * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP: Ext scan stop * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS: Ext scan get valid * channels * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES: Ext scan get capability * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS: Ext scan get cached * results * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE: Ext scan results * available. Used when report_threshold is reached in scan cache. * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT: Ext scan full scan * result. Used to report scan results when each probe rsp. is received, * if report_events enabled in wifi_scan_cmd_params. * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT: Ext scan event from target. * Indicates progress of scanning state-machine. * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND: Ext scan hotlist * ap found * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST: Ext scan set hotlist * bssid * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST: Ext scan reset * hotlist bssid * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE: Ext scan significant * change * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE: Ext scan set * significant change * ap found * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE: Ext scan reset * significant change * @QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE: This command is used to enable TDLS * capability or to form a session with the specified peer. * If %NL80211_ATTR_VENDOR_DATA is sent as an empty nested attribute this * indicates to enable TDLS capability on the interface. * If %QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR is nested in * %NL80211_ATTR_VENDOR_DATA this indicates the userspace requests to * form a TDLS session with the specified peer MAC address. * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_tdls_enable. * @QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE: This command is used to disable TDLS * capability or to terminate the session with the specified peer. * If %NL80211_ATTR_VENDOR_DATA is sent as an empty nested attribute this * indicates to disable TDLS capability on the interface. * If %QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR is nested in * %NL80211_ATTR_VENDOR_DATA this indicates the userspace requests to * terminate TDLS session with the specified peer MAC address. * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_tdls_disable. * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS: This command is to get the TDLS * status at the interface level or with the specific peer. * If %NL80211_ATTR_VENDOR_DATA is sent as an empty nested attribute this * indicates the TDLS status query is at interface level. * If %QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR is nested in * %NL80211_ATTR_VENDOR_DATA this indicates the userspace requests to * get TDLS session status with the specified peer MAC address. * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_tdls_get_status. * @QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE: This event is to indicate the result * of the TDLS session request with the peer sent by userspace in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE. * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_tdls_state. * @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES: Get supported features * @QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI: Set scanning_mac_oui * @QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG: No DFS flag * @QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX: Get Concurrency Matrix * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Get the key mgmt offload keys * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: After roaming, send the * roaming and auth information. * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_SCHED: Set OCB schedule * * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to * invoke the ACS function in device and pass selected channels to * hostapd. Uses enum qca_wlan_vendor_attr_acs_offload attributes. * * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Get the supported features by the * driver. * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Indicate that driver * started CAC on DFS channel * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Indicate that driver * completed the CAC check on DFS channel * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Indicate that the CAC * check was aborted by the driver * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Indicate that the * driver completed NOP * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Indicate that the * driver detected radar signal on the current operating channel * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO: get wlan driver information * @QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION: This command is used to * configure various wiphy or interface level configurations. Attributes * are defined in enum qca_wlan_vendor_attr_config. Userspace can send one * or more configuration attributes with a single command. The driver * accepts the command only if all the configurations are known, otherwise * it rejects the command. The driver returns success only if processing of * all the configurations succeeds. The driver continues to process all the * configurations even if processing of some configurations failed and * returns the last error occurred while processing the failed * configurations. * * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION: This command is used to * get the current values of the various wiphy or interface level * configurations. Attributes are defined in enum * qca_wlan_vendor_attr_config. Userspace needs to specify the * configuration attributes for which it wants to get the values in the * command, there is no significance for the value sent in the attribute * unless explicitly specified in the corresponding configuration * attribute documentation. The driver accepts the command only if all the * configurations are known, otherwise it rejects the command. The driver * returns success only if fetching of all configuration values succeeds * and indicates the configuration values in corresponding attributes in * the response. The driver continues to process all the configurations * even if processing of some configurations failed and returns the last * error occurred while processing the failed configurations. * * @QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START: start wifi logger * @QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP: memory dump request * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: get logger feature set * @QCA_NL80211_VENDOR_SUBCMD_ROAM: roam * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST: extscan set ssid hotlist * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST: * extscan reset ssid hotlist * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND: hotlist ssid found * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST: hotlist ssid lost * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_LIST: set pno list * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_PASSPOINT_LIST: set passpoint list * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_RESET_PASSPOINT_LIST: * reset passpoint list * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND: pno network found * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND: * passpoint network found * @QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION: set wifi config * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION: get wifi config * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: get logging features * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: get link properties * @QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG: set gateway parameters * @QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST: get preferred channel list * @QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL: channel hint * @QCA_NL80211_VENDOR_SUBCMD_SETBAND: Command to configure the band * to the host driver. This command sets the band through either * the attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE or * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE * refers enum qca_set_band as unsigned integer values and * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK refers it as 32 bit unsigned BitMask * values. Also, the acceptable values for * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE are only till QCA_SETBAND_2G. Further * values/bitmask's are valid for QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. The * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE is deprecated and the * recommendation is to use the QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. If the * implementations configure using both the attributes, the configurations * through QCA_WLAN_VENDOR_ATTR_SETBAND_MASK shall always take the * precedence. * @QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN: venodr scan command * @QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE: vendor scan complete * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: vendor abort scan * @QCA_NL80211_VENDOR_SUBCMD_OTA_TEST: enable OTA test * @QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE: set tx power by percentage * @QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE_DECR_DB: reduce tx power by DB * @QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG: SAP configuration * @QCA_NL80211_VENDOR_SUBCMD_TSF: TSF operations command * @QCA_NL80211_VENDOR_SUBCMD_WISA: WISA mode configuration * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to * start the P2P Listen Offload function in device and pass the listen * channel, period, interval, count, number of device types, device * types and vendor information elements to device driver and firmware. * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to * indicate stop request/response of the P2P Listen Offload function in * device. As an event, it indicates either the feature stopped after it * was already running or feature has actually failed to start. * @QCA_NL80211_VENDOR_SUBCMD_GET_STATION: send BSS Information * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After SAP starts * beaconing, this sub command provides the driver, the frequencies on the * 5 GHz to check for any radar activity. Driver selects one channel from * this priority list provided through * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts * to check for radar activity on it. If no radar activity is detected * during the channel availability check period, driver internally switches * to the selected frequency of operation. If the frequency is zero, driver * internally selects a channel. The status of this conditional switch is * indicated through an event using the same sub command through * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Command/event used to config * indication period and threshold for MAC layer counters. * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior * in the host driver. The different TDLS configurations are defined * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Get HE related capabilities * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS:Set the Specific Absorption Rate * (SAR) power limits. A critical regulation for FCC compliance, OEMs * require methods to set SAR limits on TX power of WLAN/WWAN. * enum qca_vendor_attr_sar_limits attributes are used with this command. * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: Vendor command used to get/set * configuration of vendor ACS. * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the * requisite information leading to a power save failure. The information * carried as part of this event is represented by the * enum qca_attr_chip_power_save_failure attributes. * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics * collection. Uses attributes defined in enum qca_attr_nud_stats_set. * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These * statistics are represented by the enum qca_attr_nud_stats_get * attributes. * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch * the BSS transition status, whether accept or reject, for a list of * candidate BSSIDs provided by the userspace. This uses the vendor * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response * the driver shall specify array of * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a * specific QCA module. The trace levels are represented by * enum qca_attr_trace_level attributes. * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement * Protocol antenna limit in different modes. See enum * qca_wlan_vendor_attr_brp_ant_limit_mode. * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) * identifying the operation in success case. In failure cases an * error code (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE) * describing the reason for the failure is returned. * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to * be stopped. * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the * specific interface. This can be used to modify some of the low level * scan parameters (off channel dwell time, home channel time) in the * driver/firmware. These parameters are maintained within the host * driver. * This command is valid only when the interface is in the connected * state. * These scan parameters shall be reset by the driver/firmware once * disconnected. The attributes used with this command are defined in * enum qca_wlan_vendor_attr_active_tos. * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the * driver has detected an internal failure. This event carries the * information indicating the reason that triggered this detection. The * attributes for this command are defined in * enum qca_wlan_vendor_attr_hang. * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values * of spectral parameters used. The spectral scan parameters are specified * by enum qca_wlan_vendor_attr_spectral_scan. * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats * for spectral scan functionality. The debug stats are specified by * enum qca_wlan_vendor_attr_spectral_diag_stats. * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral * scan system capabilities. The capabilities are specified * by enum qca_wlan_vendor_attr_spectral_cap. * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current * status of spectral scan. The status values are specified * by enum qca_wlan_vendor_attr_spectral_scan_status. * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush * peer pending packets. Specify the peer MAC address in * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed * in enum qca_wlan_vendor_attr_flush_pending. * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative * RF Operating Parameter (RROP) information. The attributes for this * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is * intended for use by external Auto Channel Selection applications. * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate * (SAR) power limits. This is a companion to the command * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the * settings currently in use. The attributes returned by this command are * defined by enum qca_vendor_attr_sar_limits. * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behaviour of * the WLAN hardware MAC's associated with each WLAN netdev interface. * This works both as a query (user space asks the current mode) or event * interface (driver advertizing the current mode to the user space). * Driver does not trigger this event for temporary hardware mode changes. * Mode changes w.r.t Wi-Fi connection updation ( VIZ creation / deletion, * channel change etc ) are updated with this event. Attributes for this * interface are defined in enum qca_wlan_vendor_attr_mac. * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold * per peer per TID. Attributes for this command are define in * enum qca_wlan_set_qdepth_thresh_attr * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action * guide for WLAN driver. Request to suspend of driver and FW if the * temperature is higher than the suspend threshold; resume action is * requested to driver if the temperature is lower than the resume * threshold. In user poll mode, request temperature data by user. For test * purpose, getting thermal shutdown configuration parameters is needed. * Attributes for this interface are defined in * enum qca_wlan_vendor_attr_thermal_cmd. * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from * driver. Thermal temperature and indication of resume completion are * reported as thermal events. The attributes for this command are defined * in enum qca_wlan_vendor_attr_thermal_event. * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi * test configuration. Attributes for this command are defined in * enum qca_wlan_vendor_attr_wifi_test_config. * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, * carried a payload which was a binary blob of data. The command was not * extendable to send more information. The newer version carries the * legacy blob encapsulated within an attribute and can be extended with * additional vendor attributes that can enhance the NAN command * interface. * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to * configure parameters per peer to capture Channel Frequency Response * (CFR) and enable Periodic CFR capture. The attributes for this command * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr. This command * can also be used to send CFR data from the driver to userspace when * netlink events are used to send CFR data. * @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: Sub command to get firmware state. * The returned firmware state is specified in the attribute * QCA_WLAN_VENDOR_ATTR_FW_STATE. * @QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH: This vendor subcommand * is used by host driver to flush per-peer cached statistics to user space * application. This interface is used as an event from host driver to * user space application. Attributes for this event are specified in * enum qca_wlan_vendor_attr_peer_stats_cache_params. * QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA attribute is expected to be * sent as event from host driver. * @QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG: This sub command is used to * improve the success rate of Zigbee joining network. * Due to PTA master limitation, zigbee joining network success rate is * low while wlan is working. Wlan host driver need to configure some * parameters including Zigbee state and specific WLAN periods to enhance * PTA master. All this parameters are delivered by the NetLink attributes * defined in "enum qca_mpta_helper_vendor_attr". * @QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING: This sub command is used to * implement Beacon frame reporting feature. * * Userspace can request the driver/firmware to periodically report * received Beacon frames whose BSSID is same as the current connected * BSS's MAC address. * * In case the STA seamlessly (without sending disconnect indication to * userspace) roams to a different BSS, Beacon frame reporting will be * automatically enabled for the Beacon frames whose BSSID is same as the * MAC address of the new BSS. Beacon reporting will be stopped when the * STA is disconnected (when the disconnect indication is sent to * userspace) and need to be explicitly enabled by userspace for next * connection. * * When a Beacon frame matching configured conditions is received, and if * userspace has requested to send asynchronous beacon reports, the * driver/firmware will encapsulate the details of the Beacon frame in an * event and send it to userspace along with updating the BSS information * in cfg80211 scan cache, otherwise driver will only update the cfg80211 * scan cache with the information from the received Beacon frame but * will not send any active report to userspace. * * The userspace can request the driver/firmware to stop reporting Beacon * frames. If the driver/firmware is not able to receive Beacon frames * due to other Wi-Fi operations such as off-channel activities, etc., * the driver/firmware will send a pause event to userspace and stop * reporting Beacon frames. Whether the beacon reporting will be * automatically resumed or not by the driver/firmware later will be * reported to userspace using the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES flag. The beacon * reporting shall be resumed for all the cases except either when * userspace sets QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME flag * in the command which triggered the current beacon reporting or during * any disconnection case as indicated by setting * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON to * QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED by the * driver. * * After QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_PAUSE event is received * by userspace with QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES * flag not set, the next first * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO event from the driver * shall be considered as un-pause event. * * All the attributes used with this command are defined in * enum qca_wlan_vendor_attr_beacon_reporting_params. * @QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP: In practice, some aps have * interop issues with the DUT. This sub command is used to transfer the * ap info between driver and user space. This works both as a command * or event. As a command, it configs the stored list of aps from user * space to firmware; as an event, it indicates the ap info detected by * firmware to user space for persistent storage. The attributes defined * in enum qca_vendor_attr_interop_issues_ap are used to deliver the * parameters. * @QCA_NL80211_VENDOR_SUBCMD_OEM_DATA: This command is used to send OEM data * binary blobs from application/service to firmware. The attributes * defined in enum qca_wlan_vendor_attr_oem_data_params are used to * deliver the parameters. * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT: This command/event is used * to send/receive avoid frequency data using * enum qca_wlan_vendor_attr_avoid_frequency_ext. * This new command is alternative to existing command * QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command/event * is using stream of bytes instead of structured data using vendor * attributes. User space sends unsafe frequency ranges to the driver using * a nested attribute %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE. On * reception of this command, the driver shall check if an interface is * operating on an unsafe frequency and the driver shall try to move to a * safe channel when needed. If the driver is not able to find a safe * channel the interface can keep operating on an unsafe channel with the * TX power limit derived based on internal configurations like * regulatory/SAR rules. * * @QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE: This vendor subcommand is used to * add the STA node details in driver/firmware. Attributes for this event * are specified in enum qca_wlan_vendor_attr_add_sta_node_params. * @QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE: This command is used to set BT * coex chain mode from application/service. * The attributes defined in enum qca_vendor_attr_btc_chain_mode are used * to deliver the parameters. * @QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO: This vendor subcommand is used to * get information of a station from driver to userspace. This command can * be used in both STA and AP modes. For STA mode, it provides information * of the current association when in connected state or the last * association when in disconnected state. For AP mode, only information * of the currently connected stations is available. This command uses * attributes defined in enum qca_wlan_vendor_attr_get_sta_info. * @QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT: This acts as an event. * Host drivers can request the user space entity to set the SAR power * limits with this event. Accordingly, the user space entity is expected * to set the SAR power limits. Host drivers can retry this event to the * user space for the SAR power limits configuration from user space. If * the driver does not get the SAR power limits from user space for all * the retried attempts, it can configure a default SAR power limit. * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO: This acts as a vendor event and * is used to update the information about the station from the driver to * userspace. Uses attributes from enum * qca_wlan_vendor_attr_update_sta_info. * * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON: This acts as an event. * The host driver initiates the disconnection for scenarios such as beacon * miss, NUD failure, peer kick out, etc. The disconnection indication * through cfg80211_disconnected() expects the reason codes from enum * ieee80211_reasoncode which does not signify these various reasons why * the driver has triggered the disconnection. This event will be used to * send the driver specific reason codes by the host driver to userspace. * Host drivers should trigger this event and pass the respective reason * code immediately prior to triggering cfg80211_disconnected(). The * attributes used with this event are defined in enum * qca_wlan_vendor_attr_driver_disconnect_reason. * * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC: This vendor subcommand is used to * add/delete TSPEC for each AC. One command is for one specific AC only. * This command can only be used in STA mode and the STA must be * associated with an AP when the command is issued. Uses attributes * defined in enum qca_wlan_vendor_attr_config_tspec. * * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT: Vendor subcommand to configure TWT. * Uses attributes defined in enum qca_wlan_vendor_attr_config_twt. * * @QCA_NL80211_VENDOR_SUBCMD_GETBAND: Command to get the configured band from * the host driver. The band configurations obtained are referred through * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. * * @QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS: Vendor subcommand/event for medium * assessment. * Uses attributes defined in enum qca_wlan_vendor_attr_medium_assess. * * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID: This acts as a vendor event and is * used to update SSID information in hostapd when it is updated in the * driver. Uses the attribute NL80211_ATTR_SSID. * * @QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS: This vendor subcommand is used by * the driver to send opaque data from the firmware to userspace. The * driver sends an event to userspace whenever such data is received from * the firmware. * * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA is used as the attribute to * send this opaque data for this event. * * The format of the opaque data is specific to the particular firmware * version and there is no guarantee of the format remaining same. * * @QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS: This acts as an event. * The host driver selects Tx VDEV, and notifies user. The attributes * used with this event are defined in enum * qca_wlan_vendor_attr_mbssid_tx_vdev_status. * This event contains Tx VDEV group information contains other VDEVs * interface index and status information. * * @QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY: Vendor command to * configure the concurrent session policies when multiple interfaces * are (getting) active. The attributes used by this command are defined * in enum qca_wlan_vendor_attr_concurrent_policy. * * @QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS: Userspace can use this command * to query usable channels for different interface types such as STA, * AP, P2P GO, P2P Client, NAN, etc. The driver shall report all usable * channels in the response based on country code, different static * configurations, concurrency combinations, etc. The attributes used * with this command are defined in * enum qca_wlan_vendor_attr_usable_channels. * * @QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY: This vendor subcommand is used * to get DFS radar history from the driver to userspace. The driver * returns QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES attribute with an * array of nested entries. * @QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD: Userspace can use this command to * enable/disable mDNS offload to the firmware. The attributes used with * this command are defined in enum qca_wlan_vendor_attr_mdns_offload. * * @QCA_NL80211_VENDOR_SUBCMD_DIAG_DATA: Driver uses this command to send * important debug events that are required for various issues. The * attributes used with this command are defined in * enum qca_wlan_vendor_attr_diag. * This command is defined for temporary usage until this interface is * moved to the existing diag infra with cnss diag events. This command * will be deprecated soon and it is not recommended to do any further * enhancements to this command. * * @QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE: This vendor subcommand is used * to set packet monitor mode that aims to send the specified set of TX and * RX frames on the current client interface to an active monitor interface. * If this Monitor mode is set, the driver will send the configured frames, * from the interface on which the command is issued, to an active monitor * interface. The attributes used with this command are defined in * enum qca_wlan_vendor_attr_set_monitor_mode. * * Though the monitor mode is configured for the respective data/mgmt/ctrl * frames, it is up to the respective WLAN driver/firmware/hardware designs * to consider the possibility of sending these frames over the monitor * interface. For example, the control frames are handled with in the * hardware and thus passing such frames over the monitor interface is left * to the respective designs. * * Also, this monitor mode is governed to behave accordingly in * suspend/resume states. If the firmware handles any of such frames * in suspend state without waking up the host and if the monitor mode * is configured to notify all such frames, then the firmware is expected * to resume the host and forward the respective frames to the monitor * interface. Please note that such a request to get the frames over the * monitor interface will have a definite power implications. * * @QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS: This vendor subcommand is used both * as a request to set the driver/firmware with the parameters to trigger * the roaming events, and also used by the driver/firmware to pass on the * various roam events to userspace. * Applicable only for the STA mode. The attributes used with this command * are defined in enum qca_wlan_vendor_attr_roam_events. * * @QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG: Sub-command to set or reset the * rate mask config for a list of phy types. Userspace shall provide * an array of the vendor attributes defined in * enum QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS. * * @QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA: Multi-channel Concurrency (MCC) occurs * when two interfaces are active on the same band, using two different * home channels, and only supported by a single radio. In this scenario * the device must split the use of the radio between the two interfaces. * The percentage of time allocated to a given interface is the quota. * Depending on the configuration, the quota can either be fixed or * dynamic. * * When used as an event, the device will report the quota type, and for * all interfaces operating in MCC it will report the current quota. * When used as a command, the device can be configured for a specific * quota type, and in the case of a fixed quota, the quota to apply to one * of the interfaces. * * Applications can use the event to do TX bitrate control based on the * information, and can use the command to explicitly set the quota to * enhance performance in specific scenarios. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_mcc_quota. * * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_READY: Event indicating to the * user space that the driver is ready for operations again after * recovering from internal failures. This occurs following a failure * that was indicated by @QCA_NL80211_VENDOR_SUBCMD_HANG. * * @QCA_NL80211_VENDOR_SUBCMD_GET_RADIO_COMBINATION_MATRIX: Vendor command to * get the WLAN radio combinations matrix supported by the device which * provides the device simultaneous radio configurations such as * standalone, dual band simultaneous, and single band simultaneous. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_radio_combination_matrix. * * @QCA_NL80211_VENDOR_SUBCMD_PASN: Subcommand used to offload preassociation * security negotiation and key generation to user space. * * When used as an event, the driver requests userspace to trigger the PASN * authentication or dropping of a PTKSA for the indicated peer devices. * When used as a command response, userspace indicates a consolidated * status report for all the peers that were requested for. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_pasn. * * @QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT: Subcommand used to set * secure ranging context such as TK and LTF keyseed for each peer * requested by the driver with a @QCA_NL80211_VENDOR_SUBCMD_PASN event. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_secure_ranging_ctx. * * @QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD: This vendor subcommand is used to * enable/disable offload processing in firmware during system/runtime * suspend for CoAP messages (see RFC7252: The Constrained Application * Protocol) and fetch information of the CoAP messages cached during * offload processing. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_coap_offload. * * @QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG: Subcommand to configure * (add, remove, or change) a Stream Classification Service (SCS) rule. * * The attributes used with this event are defined in * enum qca_wlan_vendor_attr_scs_rule_config. * * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY: Fetch SAR capabilities * supported by the WLAN firmware. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_sar_capability. * * @QCA_NL80211_VENDOR_SUBCMD_SR: Subcommand used to implement Spatial Reuse * (SR) feature. This command is used by userspace to configure SR * parameters to the driver and to get the SR related parameters and * statistics with synchronous responses from the driver. * The driver also uses this command to send asynchronous events to * userspace to indicate suspend/resume of SR feature and changes * in SR parameters. * * The attributes used with this command are defined in * enum qca_wlan_vendor_attr_sr. * * @QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT: Subcommand used to * notify application layer about the primary netdev of an MLO connection. * In some implementations, MLO has multiple netdevs out of which one * netdev is designated as primary to provide a unified interface to the * bridge. In those implementations this event is sent on every MLO peer * connection. User applications on an AP MLD will use this event to get * info for all the links from non-AP MLD that were negotiated to be used * for the ML association. * * The attributes used with this event are defined in * enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event. * * @QCA_NL80211_VENDOR_SUBCMD_AFC_EVENT: This vendor command is used by the * driver to notify different AFC events to userspace. The attributes used * with this command are defined in enum qca_wlan_vendor_attr_afc_event. * * @QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE: This vendor command is used by * userspace to deliver AFC response data to driver. The attributes used * with this command are defined in enum qca_wlan_vendor_attr_afc_response. * * @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP: Subcommand to configure AP interface to * operate in doze mode. * * Userspace uses this command to configure the AP interface to enter or * exit from doze mode. The driver sends this event after it enters or * exits the doze mode with the updated AP doze mode settings. * * The attributes used with this subcommand are defined in * enum qca_wlan_vendor_attr_dozed_ap. * * @QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE: This vendor subcommand is used * to get the status of local packet capture of monitor mode. The monitor * mode can be started using QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE * subcommand. * * The attributes used with this command are defined in enum * qca_wlan_vendor_attr_get_monitor_mode. * * @QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS: This vendor command is used to * get roam information from the driver to user space. It provides the * latest several instances of roam information cached in the driver. * The command is only used for STA mode. The attributes used with this * command are defined in enum qca_wlan_vendor_attr_roam_cached_stats. * * @QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE: This vendor subcommand is used to * configure and fetch the state information of the MLO links affiliated * with the STA interface. The attributes used with this command are * defined in enum qca_wlan_vendor_attr_mlo_link_state. * * @QCA_NL80211_VENDOR_SUBCMD_CONNECTED_CHANNEL_STATS: Userspace can use this * vendor subcommand to trigger channel utilization measurement on entire * channel width of the connected channel(s). For MLO connection, connected * channel utilization measurement shall be done on all the MLO links. * The driver may use regular scan or wideband energy detection feature * based on the hardware capability for connected channel(s) utilization * measurement. The driver indicates the connected channel(s) utilization * measurement completion as an asynchronous event with this command ID to * userspace. Upon receiving this event, userspace can use * %NL80211_CMD_GET_INTERFACE to determine the channel width of the current * connected channel(s) and can derive the channel utilization percentage * (CU) of each 20 MHz sub-channel of the entire connected channel using * %NL80211_CMD_GET_SURVEY response. * CU = %NL80211_SURVEY_INFO_TIME_BUSY * 100 / %NL80211_SURVEY_INFO_TIME. * This command is only used for STA mode. * * @QCA_NL80211_VENDOR_SUBCMD_TID_TO_LINK_MAP: This vendor subcommand is * used as an event to notify the userspace of TID-to-link map changes * negotiated by the driver or updated by associated AP MLD with Beacon, * Probe Response, or Action frames. The attributes used with this command * are defined in enum qca_wlan_vendor_attr_tid_to_link_map. * * Note that the attribute * %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AP_MLD_ADDR may not correspond to * the current connected AP MLD address. * * @QCA_NL80211_VENDOR_SUBCMD_LINK_RECONFIG: Notify userspace about the removal * of STA MLD setup links due to AP MLD removing the corresponding * affiliated APs with Multi-Link reconfiguration. If all the STA MLD setup * links are removed during Multi-Link reconfiguration, the driver shall * use %NL80211_CMD_DISCONNECT instead of this command since it is a * connection drop. The attributes used with this command are defined in * enum qca_wlan_vendor_attr_link_reconfig. * Note that the attribute * %QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AP_MLD_ADDR may not correspond to * the current connected AP MLD address. * * @QCA_NL80211_VENDOR_SUBCMD_TDLS_DISC_RSP_EXT: Vendor command to configure * the driver with MLO link id information on which to transmit the TDLS * discovery response frame on the configured MLO BSS link when the * local station is connected in MLO mode. This command is sent to the * driver prior to the TDLS discovery response management transmit * operation and is followed immediately by the TDLS discovery response * management frame transmit command. * * The driver saves the configured MLO link id information and uses it for * the following TDLS discovery response frame transmission on the * configured MLO BSS link and the link id information is cleared in the * driver after the TDLS discovery response frame is successfully * transmitted. This behavior is independent of the TDLS peer STA connection * mode (MLO or non-MLO). * * Uses the attributes defined in * enum qca_wlan_vendor_attr_tdls_disc_rsp_ext. * * @QCA_NL80211_VENDOR_SUBCMD_AUDIO_TRANSPORT_SWITCH: This vendor subcommand is * used to configure and indicate the audio transport switch in both * command and event paths. This is used when two or more audio transports * (ex: WLAN and bluetooth) are available between peers. * * If the driver needs to perform operations like scan, connection, * roaming, RoC etc. and AP concurrency policy is set to either * QCA_WLAN_CONCURRENT_AP_POLICY_GAMING_AUDIO or * QCA_WLAN_CONCURRENT_AP_POLICY_LOSSLESS_AUDIO_STREAMING, the driver sends * audio transport switch event to userspace. Userspace application upon * receiving the event, can try to switch to requested audio transport. * The userspace uses this command to send the status of transport * switching (either confirm or reject) to the driver using this * subcommand. The driver continues with the pending operation either upon * receiving the command from userspace or after waiting for timeout since * sending the event to userspace. The driver can request userspace to * switch to WLAN upon availability of WLAN audio transport once after the * concurrent operations are completed. * * Userspace can also request audio transport switch from non-WLAN to WLAN * using this subcommand to the driver. The driver can accept or reject * depending on other concurrent operations in progress. The driver returns * success if it can allow audio transport when it receives the command or * appropriate kernel error code otherwise. Userspace indicates the audio * transport switch from WLAN to non-WLAN using this subcommand and the * driver can do other concurrent operations without needing to send any * event to userspace. This subcommand is used by userspace only when the * driver advertises support for * QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN. * * The attributes used with this command are defined in enum * qca_wlan_vendor_attr_audio_transport_switch. * * @QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY: This vendor subcommand is used to * configure, retrieve, and report per-link transmit latency statistics. * * The attributes used with this subcommand are defined in * enum qca_wlan_vendor_attr_tx_latency. * * @QCA_NL80211_VENDOR_SUBCMD_RECONFIG_REMOVE_COMPLETE_EVENT: This vendor * subcommand is used to send event to the user space once the MLD remove * link process is completed in the API mlme_ext_vap_down and the event * is sent through wlan_cfg80211_reconfig_remove_complete_event. * * @QCA_NL80211_VENDOR_SUBCMD_REGULATORY_TPC_INFO: Vendor command is used to * query transmit power information on STA interface from the driver for a * connected AP. The attributes included in response are defined in * enum qca_wlan_vendor_attr_tpc_links. In case of MLO STA, multiple links * TPC info may be returned. The information includes regulatory maximum * transmit power limit, AP local power constraint advertised from AP's * Beacon and Probe Response frames. For PSD power mode, the information * includes PSD power levels for each subchannel of operating bandwidth. * The information is driver calculated power limits based on the current * regulatory domain, AP local power constraint, and other IEs. The * information will be set to target. Target will decide the final TX power * based on this and chip specific power conformance test limits (CTL), and * SAR limits. * * @QCA_NL80211_VENDOR_SUBCMD_FW_PAGE_FAULT_REPORT: Event indication from the * driver to user space which is carrying firmware page fault related * summary report. The attributes for this command are defined in * enum qca_wlan_vendor_attr_fw_page_fault_report. */ enum qca_nl80211_vendor_subcmds { QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, QCA_NL80211_VENDOR_SUBCMD_TEST = 1, QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, QCA_NL80211_VENDOR_SUBCMD_NAN = 12, QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START = 20, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP = 21, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS = 22, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES = 23, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS = 24, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE = 25, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT = 26, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT = 27, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND = 28, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST = 29, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST = 30, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE = 31, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE = 32, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE = 33, QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST = 41, /* Get Concurrency Matrix */ QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, /* Deprecated */ QCA_NL80211_VENDOR_SUBCMD_OCB_SET_SCHED = 53, QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, /* Off loaded DFS events */ QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST = 65, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST = 66, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND = 67, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST = 68, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_LIST = 69, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_PASSPOINT_LIST = 70, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_RESET_PASSPOINT_LIST = 71, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND = 72, QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND = 73, /* Wi-Fi Configuration subcommands */ QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, QCA_NL80211_VENDOR_SUBCMD_NDP = 81, /* NS Offload enable/disable cmd */ QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, /* OCB commands */ QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, /* subcommand to get link properties */ QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, /* LFR Subnet Detection */ QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, /* DBS subcommands */ QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, /* Vendor setband command */ QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, /* Vendor scan commands */ QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, /* OTA test subcommand */ QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, /* Tx power scaling subcommands */ QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, /* Tx power scaling in db subcommands */ QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE_DECR_DB = 115, QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY = 116, QCA_NL80211_VENDOR_SUBCMD_STA_CONNECT_ROAM_POLICY = 117, QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, QCA_NL80211_VENDOR_SUBCMD_TSF = 119, QCA_NL80211_VENDOR_SUBCMD_WISA = 120, QCA_NL80211_VENDOR_SUBCMD_GET_STATION = 121, QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, /* FTM/indoor location subcommands */ QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, /* Encrypt/Decrypt command */ QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, /* DMG low level RF sector operations */ QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, /* Configure the TDLS mode from user space */ QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, /* Vendor abort scan command */ QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, /* Set Specific Absorption Rate(SAR) Power Limits */ QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, /* External Auto channel configuration setting */ QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, /* Set the trace level for QDF */ QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, QCA_NL80211_VENDOR_SUBCMD_HANG = 157, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162, QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167, QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168, /* Wi-Fi test configuration subcommand */ QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173, QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175, QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177, QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178, QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179, QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING = 180, QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP = 181, QCA_NL80211_VENDOR_SUBCMD_OEM_DATA = 182, QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT = 183, QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE = 184, QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE = 185, QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO = 186, QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS_EVENT = 187, QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO = 188, QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON = 189, QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC = 190, QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT = 191, QCA_NL80211_VENDOR_SUBCMD_GETBAND = 192, QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS = 193, QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID = 194, QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS = 195, QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS = 196, QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY = 197, QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS = 198, QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY = 199, QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD = 200, QCA_NL80211_VENDOR_SUBCMD_DIAG_DATA = 201, QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE = 202, QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS = 203, QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG = 204, QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA = 205, /* 206..212 - reserved for QCA */ QCA_NL80211_VENDOR_SUBCMD_GET_RADIO_COMBINATION_MATRIX = 213, QCA_NL80211_VENDOR_SUBCMD_DRIVER_READY = 214, QCA_NL80211_VENDOR_SUBCMD_PASN = 215, QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT = 216, QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD = 217, QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG = 218, QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY = 219, QCA_NL80211_VENDOR_SUBCMD_SR = 220, QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT = 221, QCA_NL80211_VENDOR_SUBCMD_AFC_EVENT = 222, QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE = 223, QCA_NL80211_VENDOR_SUBCMD_DOZED_AP = 224, QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE = 225, QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS = 226, QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE = 227, QCA_NL80211_VENDOR_SUBCMD_CONNECTED_CHANNEL_STATS = 228, QCA_NL80211_VENDOR_SUBCMD_TID_TO_LINK_MAP = 229, QCA_NL80211_VENDOR_SUBCMD_LINK_RECONFIG = 230, QCA_NL80211_VENDOR_SUBCMD_TDLS_DISC_RSP_EXT = 231, QCA_NL80211_VENDOR_SUBCMD_AUDIO_TRANSPORT_SWITCH = 232, QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY = 233, QCA_NL80211_VENDOR_SUBCMD_RECONFIG_REMOVE_COMPLETE_EVENT = 234, QCA_NL80211_VENDOR_SUBCMD_REGULATORY_TPC_INFO = 237, QCA_NL80211_VENDOR_SUBCMD_FW_PAGE_FAULT_REPORT = 238, }; enum qca_wlan_vendor_tos { QCA_WLAN_VENDOR_TOS_BK = 0, QCA_WLAN_VENDOR_TOS_BE = 1, QCA_WLAN_VENDOR_TOS_VI = 2, QCA_WLAN_VENDOR_TOS_VO = 3, }; /** * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. */ enum qca_wlan_vendor_attr_active_tos { QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, /* Type Of Service - Represented by qca_wlan_vendor_tos */ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, /* Flag attribute representing the start (attribute included) or stop * (attribute not included) of the respective TOS. */ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_MAX = 3, }; enum qca_wlan_vendor_hang_reason { /* Unspecified reason */ QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, /* No Map for the MAC entry for the received frame */ QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, /* peer deletion timeout happened */ QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, /* peer unmap timeout */ QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, /* Scan request timed out */ QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, /* Consecutive Scan attempt failures */ QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, /* Unable to get the message buffer */ QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, /* Current command processing is timedout */ QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, /* Timeout for an ACK from FW for suspend request */ QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, /* Timeout for an ACK from FW for resume request */ QCA_WLAN_HANG_RESUME_TIMEOUT = 9, /* Transmission timeout for consecutive data frames */ QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, /* Timeout for the TX completion status of data frame */ QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, /* DXE failure for tx/Rx, DXE resource unavailability */ QCA_WLAN_HANG_DXE_FAILURE = 12, /* WMI pending commands exceed the maximum count */ QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, /* Timeout for peer STA connection accept command's response from the * FW in AP mode. This command is triggered when a STA (peer) connects * to AP (DUT). */ QCA_WLAN_HANG_AP_STA_CONNECT_REQ_TIMEOUT = 14, /* Timeout for the AP connection accept command's response from the FW * in STA mode. This command is triggered when the STA (DUT) connects * to an AP (peer). */ QCA_WLAN_HANG_STA_AP_CONNECT_REQ_TIMEOUT = 15, /* Timeout waiting for the response to the MAC HW mode change command * sent to FW as a part of MAC mode switch among DBS (Dual Band * Simultaneous), SCC (Single Channel Concurrency), and MCC (Multi * Channel Concurrency) mode. */ QCA_WLAN_HANG_MAC_HW_MODE_CHANGE_TIMEOUT = 16, /* Timeout waiting for the response from FW to configure the MAC HW's * mode. This operation is to configure the single/two MACs in either * SCC/MCC/DBS mode. */ QCA_WLAN_HANG_MAC_HW_MODE_CONFIG_TIMEOUT = 17, /* Timeout waiting for response of VDEV start command from the FW */ QCA_WLAN_HANG_VDEV_START_RESPONSE_TIMED_OUT = 18, /* Timeout waiting for response of VDEV restart command from the FW */ QCA_WLAN_HANG_VDEV_RESTART_RESPONSE_TIMED_OUT = 19, /* Timeout waiting for response of VDEV stop command from the FW */ QCA_WLAN_HANG_VDEV_STOP_RESPONSE_TIMED_OUT = 20, /* Timeout waiting for response of VDEV delete command from the FW */ QCA_WLAN_HANG_VDEV_DELETE_RESPONSE_TIMED_OUT = 21, /* Timeout waiting for response of peer all delete request command to * the FW on a specific VDEV. */ QCA_WLAN_HANG_VDEV_PEER_DELETE_ALL_RESPONSE_TIMED_OUT = 22, /* WMI sequence mismatch between WMI command and Tx completion */ QCA_WLAN_HANG_WMI_BUF_SEQUENCE_MISMATCH = 23, /* Write to Device HAL register failed */ QCA_WLAN_HANG_REG_WRITE_FAILURE = 24, /* No credit left to send the wow_wakeup_from_sleep to firmware */ QCA_WLAN_HANG_SUSPEND_NO_CREDIT = 25, /* Bus failure */ QCA_WLAN_HANG_BUS_FAILURE = 26, /* tasklet/credit latency found */ QCA_WLAN_HANG_TASKLET_CREDIT_LATENCY_DETECT = 27, /* MSDU buffers received in REO error ring, exceeding certain * threshold */ QCA_WLAN_HANG_RX_MSDU_BUF_RCVD_IN_ERR_RING = 28, /* Vdev SM is out of sync and connect req received * when already connected */ QCA_WLAN_HANG_VDEV_SM_OUT_OF_SYNC = 29, /* Stats request timeout */ QCA_WLAN_HANG_STATS_REQ_TIMEOUT = 30, /* Leak in TX descriptor for a packet */ QCA_WLAN_HANG_TX_DESC_LEAK = 31, /* Scheduler watchdog timeout */ QCA_WLAN_HANG_SCHED_TIMEOUT = 32, /* Failed to send self peer deletion cmd to firmware */ QCA_WLAN_HANG_SELF_PEER_DEL_FAIL = 33, /* Received del self sta without del bss */ QCA_WLAN_HANG_DEL_SELF_STA_FAIL = 34, /* Recovery needed when sending flush completion to userspace */ QCA_WLAN_HANG_FLUSH_LOGS = 35, /* Host wakeup because of page fault */ QCA_WLAN_HANG_HOST_WAKEUP_REASON_PAGE_FAULT = 36, }; /** * enum qca_wlan_vendor_attr_fw_page_fault_report - Used by the vendor * command %QCA_NL80211_VENDOR_SUBCMD_FW_PAGE_FAULT_REPORT. * * @QCA_WLAN_VENDOR_ATTR_FW_PAGE_FAULT_REPORT_DATA: The binary blob data * associated with the firmware page fault that is expected to contain the * required dump to analyze frequent page faults. * NLA_BINARY attribute, the maximum size is QDF_HANG_EVENT_DATA_SIZE */ enum qca_wlan_vendor_attr_fw_page_fault_report { QCA_WLAN_VENDOR_ATTR_FW_PAGE_FAULT_REPORT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_FW_PAGE_FAULT_REPORT_DATA = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_FW_PAGE_FAULT_REPORT_LAST, QCA_WLAN_VENDOR_ATTR_FW_PAGE_FAULT_REPORT_MAX = QCA_WLAN_VENDOR_ATTR_FW_PAGE_FAULT_REPORT_LAST - 1, }; /** * enum qca_wlan_vendor_attr_hang - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_HANG. */ enum qca_wlan_vendor_attr_hang { QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, /* * Reason for the Hang - Represented by enum * qca_wlan_vendor_hang_reason. */ QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, /* The binary blob data associated with the hang reason specified by * QCA_WLAN_VENDOR_ATTR_HANG_REASON. This binary data is expected to * contain the required dump to analyze the reason for the hang. * NLA_BINARY attribute, the max size is 1024 bytes. */ QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA = 2, QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_HANG_MAX = QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, }; /** * enum qca_vendor_attr_set_trace_level - Config params for QDF set trace level * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_INVALID: Invalid trace level * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM : Trace level parameters * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MODULE_ID : Module of which trace level needs to be updated. * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_TRACE_MASK : verbose mask, which need * to be set. * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST : after last. * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MAX : Max attribute. */ enum qca_vendor_attr_set_trace_level { QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_INVALID = 0, /* * Array of QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM * attributes. */ QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM = 1, QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MODULE_ID = 2, QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_TRACE_MASK = 3, QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MAX = QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_station - Sub commands used by * QCA_NL80211_VENDOR_SUBCMD_GET_STATION to get the corresponding * station information. The information obtained through these * commands signify the current info in connected state and * latest cached information during the connected state , if queried * when in disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INVALID: Invalid attribute * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO: bss info * @QCA_WLAN_VENDOR_ATTR_GET_STATION_ASSOC_FAIL_REASON: assoc fail reason * @QCA_WLAN_VENDOR_ATTR_GET_STATION_REMOTE: remote station info * @QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST: After last */ enum qca_wlan_vendor_attr_get_station { QCA_WLAN_VENDOR_ATTR_GET_STATION_INVALID = 0, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO, QCA_WLAN_VENDOR_ATTR_GET_STATION_ASSOC_FAIL_REASON, QCA_WLAN_VENDOR_ATTR_GET_STATION_REMOTE, /* keep last */ QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_STATION_MAX = QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_update_sta_info - Defines attributes * used by QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO vendor command. * * @QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS: Type is NLA_UNSPEC. * Used in STA mode. This attribute represents the list of channel center * frequencies in MHz (u32) the station has learnt during the last connection * or roaming attempt. This information shall not signify the channels for * an explicit scan request from the user space. Host drivers can update this * information to the user space in both connected and disconnected state. * In the disconnected state this information shall signify the channels * scanned in the last connection/roam attempt that lead to the disconnection. */ enum qca_wlan_vendor_attr_update_sta_info { QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_MAX = QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_802_11_mode - dot11 mode * @QCA_WLAN_802_11_MODE_11B: mode B * @QCA_WLAN_802_11_MODE_11G: mode G * @QCA_WLAN_802_11_MODE_11N: mode N * @QCA_WLAN_802_11_MODE_11A: mode A * @QCA_WLAN_802_11_MODE_11AC: mode AC * @QCA_WLAN_802_11_MODE_11AX: mode AX * @QCA_WLAN_802_11_MODE_11BE: mode BE * @QCA_WLAN_802_11_MODE_INVALID: Invalid dot11 mode */ enum qca_wlan_802_11_mode { QCA_WLAN_802_11_MODE_11B, QCA_WLAN_802_11_MODE_11G, QCA_WLAN_802_11_MODE_11N, QCA_WLAN_802_11_MODE_11A, QCA_WLAN_802_11_MODE_11AC, QCA_WLAN_802_11_MODE_11AX, QCA_WLAN_802_11_MODE_11BE, QCA_WLAN_802_11_MODE_INVALID, }; /** * enum qca_wlan_auth_type - Authentication key management type * @QCA_WLAN_AUTH_TYPE_INVALID: Invalid key management type * @QCA_WLAN_AUTH_TYPE_OPEN: Open key * @QCA_WLAN_AUTH_TYPE_SHARED: shared key * @QCA_WLAN_AUTH_TYPE_WPA: wpa key * @QCA_WLAN_AUTH_TYPE_WPA_PSK: wpa psk key * @QCA_WLAN_AUTH_TYPE_WPA_NONE: wpa none key * @QCA_WLAN_AUTH_TYPE_RSN: rsn key * @QCA_WLAN_AUTH_TYPE_RSN_PSK: rsn psk key * @QCA_WLAN_AUTH_TYPE_FT: ft key * @QCA_WLAN_AUTH_TYPE_FT_PSK: ft psk key * @QCA_WLAN_AUTH_TYPE_SHA256: shared 256 key * @QCA_WLAN_AUTH_TYPE_SHA256_PSK: shared 256 psk * @QCA_WLAN_AUTH_TYPE_WAI: wai key * @QCA_WLAN_AUTH_TYPE_WAI_PSK wai psk key * @QCA_WLAN_AUTH_TYPE_CCKM_WPA: cckm wpa key * @QCA_WLAN_AUTH_TYPE_CCKM_RSN: cckm rsn key * @QCA_WLAN_AUTH_TYPE_AUTOSWITCH: Autoswitch key * @QCA_WLAN_AUTH_TYPE_FT_SAE: FT sae akm * @QCA_WLAN_AUTH_TYPE_FT_SUITEB_EAP_SHA384: FT suite B SHA384 * @QCA_WLAN_AUTH_TYPE_SAE: SAE key * @QCA_WLAN_AUTH_TYPE_FILS_SHA256: FILS SHA 256 key * @QCA_WLAN_AUTH_TYPE_FILS_SHA384: FILS SAH 384 key * @QCA_WLAN_AUTH_TYPE_FT_FILS_SHA256: FT FILS SHA 256 key * @QCA_WLAN_AUTH_TYPE_FT_FILS_SHA384: FT FILS SHA 384 key * @QCA_WLAN_AUTH_TYPE_DPP_RSN: DPP RSN key * @QCA_WLAN_AUTH_TYPE_OWE: owe key * @QCA_WLAN_AUTH_TYPE_SUITEB_EAP_SHA256 : EAP SHA 256 key * @QCA_WLAN_AUTH_TYPE_SUITEB_EAP_SHA384 : EAP SHA 384 key */ enum qca_wlan_auth_type { QCA_WLAN_AUTH_TYPE_INVALID, QCA_WLAN_AUTH_TYPE_OPEN, QCA_WLAN_AUTH_TYPE_SHARED, QCA_WLAN_AUTH_TYPE_WPA, QCA_WLAN_AUTH_TYPE_WPA_PSK, QCA_WLAN_AUTH_TYPE_WPA_NONE, QCA_WLAN_AUTH_TYPE_RSN, QCA_WLAN_AUTH_TYPE_RSN_PSK, QCA_WLAN_AUTH_TYPE_FT, QCA_WLAN_AUTH_TYPE_FT_PSK, QCA_WLAN_AUTH_TYPE_SHA256, QCA_WLAN_AUTH_TYPE_SHA256_PSK, QCA_WLAN_AUTH_TYPE_WAI, QCA_WLAN_AUTH_TYPE_WAI_PSK, QCA_WLAN_AUTH_TYPE_CCKM_WPA, QCA_WLAN_AUTH_TYPE_CCKM_RSN, QCA_WLAN_AUTH_TYPE_AUTOSWITCH, QCA_WLAN_AUTH_TYPE_FT_SAE, QCA_WLAN_AUTH_TYPE_FT_SUITEB_EAP_SHA384, QCA_WLAN_AUTH_TYPE_SAE, QCA_WLAN_AUTH_TYPE_FILS_SHA256, QCA_WLAN_AUTH_TYPE_FILS_SHA384, QCA_WLAN_AUTH_TYPE_FT_FILS_SHA256, QCA_WLAN_AUTH_TYPE_FT_FILS_SHA384, QCA_WLAN_AUTH_TYPE_DPP_RSN, QCA_WLAN_AUTH_TYPE_OWE, QCA_WLAN_AUTH_TYPE_SUITEB_EAP_SHA256, QCA_WLAN_AUTH_TYPE_SUITEB_EAP_SHA384, }; /** * enum qca_wlan_vendor_attr_get_station_info - Station Info queried * through QCA_NL80211_VENDOR_SUBCMD_GET_STATION. * * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_INVALID: Invalid Attribute * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_LINK_STANDARD_NL80211_ATTR: * Get the standard NL attributes Nested with this attribute. * Ex : Query BW , BITRATE32 , NSS , Signal , Noise of the Link - * NL80211_ATTR_SSID / NL80211_ATTR_SURVEY_INFO (Connected Channel) / * NL80211_ATTR_STA_INFO * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_STANDARD_NL80211_ATTR: * Get the standard NL attributes Nested with this attribute. * Ex : Query HT/VHT Capability advertised by the AP. * NL80211_ATTR_VHT_CAPABILITY / NL80211_ATTR_HT_CAPABILITY * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ROAM_COUNT: * Number of successful Roam attempts before a * disconnect, Unsigned 32 bit value * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AKM: * Authentication Key Management Type used for the connected session. * Signified by enum qca_wlan_auth_type * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_802_11_MODE: 802.11 Mode of the * connected Session, signified by enum qca_wlan_802_11_mode * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_HS20_INDICATION: * HS20 Indication Element * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_FAIL_REASON: * Status Code Corresponding to the Association Failure. * Unsigned 32 bit value. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_MAX_PHY_RATE: * Max phy rate of remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_PACKETS: * TX packets to remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_BYTES: * TX bytes to remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_PACKETS: * RX packets from remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BYTES: * RX bytes from remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_TX_RATE: * Last TX rate with remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_RX_RATE: * Last RX rate with remote station * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_WMM: * Remote station enable/disable WMM * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SUPPORTED_MODE: * Remote station connection mode * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AMPDU: * Remote station AMPDU enable/disable * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_STBC: * Remote station TX Space-time block coding enable/disable * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_STBC: * Remote station RX Space-time block coding enable/disable * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH: * Remote station channel width * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SGI_ENABLE: * Remote station short GI enable/disable * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_PAD: Attribute type for padding * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_BEACON_IES: Binary attribute * containing the raw information elements from Beacon frames. Represents * the Beacon frames of the current BSS in the connected state. When queried * in the disconnected state, these IEs correspond to the last connected BSSID. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_DRIVER_DISCONNECT_REASON: u32, Driver * disconnect reason for the last disconnection if the disconnection is * triggered from the host driver. The values are referred from * enum qca_disconnect_reason_codes. If the disconnect is from * peer/userspace this value is QCA_DISCONNECT_REASON_UNSPECIFIED. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_REQ_IES: Binary attribute * Applicable in AP mode only. It contains the raw information elements * from assoc request frame of the given peer station. User queries with the * mac address of peer station when it disconnects. Host driver sends * assoc request frame of the given station. Host driver doesn't provide * the IEs when the peer station is still in connected state. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_HE_OPERATION: Attribute type for * sending HE operation info. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH_V2: Attribute * type for remote channel width greater than 160 MHz. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_EHT_OPERATION: Attribute type for * sending EHT operation info. * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST: After last * */ enum qca_wlan_vendor_attr_get_station_info { QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_LINK_STANDARD_NL80211_ATTR, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_STANDARD_NL80211_ATTR, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ROAM_COUNT, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AKM, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_802_11_MODE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_HS20_INDICATION, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_HT_OPERATION, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_VHT_OPERATION, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_FAIL_REASON, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_MAX_PHY_RATE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_PACKETS, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_BYTES, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_PACKETS, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BYTES, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_TX_RATE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_RX_RATE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_WMM, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SUPPORTED_MODE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AMPDU, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_STBC, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_STBC, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SGI_ENABLE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_PAD, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_RETRY_COUNT, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BC_MC_COUNT, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_FAILURE, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AVG_RSSI_PER_CHAIN, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_SUCCEED, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_LAST_PKT_RSSI, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_EXHAUST, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_TOTAL_FW, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_FW, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_EXHAUST_FW, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_BEACON_IES, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_DRIVER_DISCONNECT_REASON, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_REQ_IES, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_HE_OPERATION, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH_V2, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_EHT_OPERATION, /* keep last */ QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_MAX = QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST - 1, }; /** * qca_chip_power_save_failure_reason: Power save failure reason * @QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL: Indicates power save failure * due to protocol/module. * @QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE: power save failure * due to hardware */ enum qca_chip_power_save_failure_reason { QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, }; /** * qca_attr_chip_power_save_failure: attributes to vendor subcmd * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carry the requisite * information leading to the power save failure. * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID : invalid * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON : power save failure reason * represented by enum qca_chip_power_save_failure_reason * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST : Last * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX : Max value */ enum qca_attr_chip_power_save_failure { QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, /* keep last */ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, }; /* enum's to provide TDLS capabilities */ enum qca_wlan_vendor_attr_get_tdls_capabilities { QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS = 1, QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, }; /* Compatibility defines for previously used subcmd names. * These values should not be used in any new implementation. */ #define QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY \ QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY enum qca_wlan_vendor_attr { QCA_WLAN_VENDOR_ATTR_INVALID = 0, /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ QCA_WLAN_VENDOR_ATTR_DFS = 1, /* used by QCA_NL80211_VENDOR_SUBCMD_NAN */ QCA_WLAN_VENDOR_ATTR_NAN = 2, /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, /* * used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined * by enum qca_roaming_policy. */ QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, QCA_WLAN_VENDOR_ATTR_TEST = 8, /* * used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES * Unsigned 32-bit value. */ QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, /* Unsigned 32-bit value from enum qca_set_band. Also, the acceptable * value for this attribute are only till QCA_SETBAND_2G. This attribute * is deprecated. Recommendation is to use * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK instead. If the band is configured * using both the attributes, the ones configured through * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK take the precedence. */ QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, /* Dummy (NOP) attribute for 64 bit padding */ QCA_WLAN_VENDOR_ATTR_PAD = 13, /* * Unique FTM session cookie (Unsigned 64 bit). Specified in * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. */ QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, /* * Indoor location capabilities, returned by * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. * see enum qca_wlan_vendor_attr_loc_capa. */ QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, /* * Array of nested attributes containing information about each peer * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info * for supported attributes for each peer. */ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, /* * Array of nested attributes containing measurement results for * one or more peers, reported by the * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. * See enum qca_wlan_vendor_attr_peer_result for list of supported * attributes. */ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, /* Flag attribute for enabling or disabling responder functionality. */ QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, /* * Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER * command to specify the LCI report that will be sent by * the responder during a measurement exchange. The format is * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. */ QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, /* * Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER * command to specify the location civic report that will * be sent by the responder during a measurement exchange. * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. */ QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, /* * Session/measurement completion status code, * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT * see enum qca_vendor_attr_loc_session_status. */ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, /* * Initial dialog token used by responder (0 if not specified), * unsigned 8 bit value. */ QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, /* * AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if * AOA measurements are needed as part of an FTM session. * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See * enum qca_wlan_vendor_attr_aoa_type. */ QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, /* * A bit mask (unsigned 32 bit value) of antenna arrays used * by indoor location measurements. Refers to the antenna * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. */ QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, /* * AOA measurement data. Its contents depends on the AOA measurement * type and antenna array mask: * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, * phase of the strongest CIR path for each antenna in the measured * array(s). * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 * values, phase and amplitude of the strongest CIR path for each * antenna in the measured array(s). */ QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, /* * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to specify the chain number (unsigned 32 bit value) to inquire * the corresponding antenna RSSI value */ QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, /* * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to report the specific antenna RSSI value (unsigned 32 bit value) */ QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, /* Frequency in MHz, various uses. Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_FREQ = 28, /* * TSF timer value, unsigned 64 bit value. * May be returned by various commands. */ QCA_WLAN_VENDOR_ATTR_TSF = 29, /* * DMG RF sector index, unsigned 16 bit number. Valid values are * 0..127 for sector indices or 65535 as special value used to * unlock sector selection in * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, /* * DMG RF sector type, unsigned 8 bit value. One of the values * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, /* * Bitmask of DMG RF modules for which information is requested. Each * bit corresponds to an RF module with the same index as the bit * number. Unsigned 32 bit number but only low 8 bits can be set since * all DMG chips currently have up to 8 RF modules. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, /* * Array of nested attributes where each entry is DMG RF sector * configuration for a single RF module. * Attributes for each entry are taken from enum * qca_wlan_vendor_attr_dmg_rf_sector_cfg. * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, /* * Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command * to report frame aggregation statistics to userspace. */ QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, /* * Unsigned 8-bit value representing MBO transition reason code as * provided by the AP used by subcommand * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is * specified by the userspace in the request to the driver. */ QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, /* * Array of nested attributes, BSSID and status code, used by subcommand * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. * The userspace space specifies the list/array of candidate BSSIDs in * the order of preference in the request. The driver specifies the * status code, for each BSSID in the list, in the response. The * acceptable candidates are listed in the order preferred by the * driver. */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, /* * Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. */ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, /* * Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command * to define the number of antennas to use for BRP. * different purpose in each ANT_LIMIT_MODE: * DISABLE - ignored * EFFECTIVE - upper limit to number of antennas to be used * FORCE - exact number of antennas to be used * unsigned 8 bit value */ QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, /* * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to report the corresponding antenna index to the chain RSSI value */ QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, /* * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to report the specific antenna EVM value (unsigned 32 bit value). * With a determinate group of antennas, the driver specifies the * EVM value for each antenna ID, and application extract them * in user space. */ QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41, /* * Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report * wlan firmware current state. FW state is an unsigned 8 bit value, * one of the values in enum qca_wlan_vendor_attr_fw_state. */ QCA_WLAN_VENDOR_ATTR_FW_STATE = 42, /* Unsigned 32-bitmask value from enum qca_set_band. Substitutes the * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE for which only the * integer values of enum qca_set_band till QCA_SETBAND_2G are valid. * This attribute shall consider the bitmask combinations to define * the respective Band combinations and always takes precedence over * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE. */ QCA_WLAN_VENDOR_ATTR_SETBAND_MASK = 43, /* Unsigned 8-bit used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES. * This field describes the maximum number of links supported by the * chip for MLO association. * This is an optional attribute. */ QCA_WLAN_VENDOR_ATTR_MLO_CAPABILITY_MAX_ASSOCIATION_COUNT = 44, /* Unsigned 8-bit used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES. * This field describes the maximum number of Simultaneous Transmit * and Receive (STR) links used in Multi-Link Operation. * The maximum number of STR links used can be different * from the maximum number of radios supported by the chip. * This is a static configuration of the chip. * This is an optional attribute. */ QCA_WLAN_VENDOR_ATTR_MLO_CAPABILITY_MAX_STR_LINK_COUNT = 45, /* keep last */ QCA_WLAN_VENDOR_ATTR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1 }; enum qca_wlan_vendor_attr_extscan_config_params { QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, /* * Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS sub command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND = 2, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS = 3, /* * Attributes for input params used by * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START sub command. */ /* Unsigned 32-bit value; channel frequency */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_CHANNEL = 4, /* Unsigned 32-bit value; dwell time in ms. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_DWELL_TIME = 5, /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_PASSIVE = 6, /* Unsigned 8-bit value; channel class */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_CLASS = 7, /* Unsigned 8-bit value; bucket index, 0 based */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_INDEX = 8, /* Unsigned 8-bit value; band. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_BAND = 9, /* Unsigned 32-bit value; desired period, in ms. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_PERIOD = 10, /* Unsigned 8-bit value; report events semantics. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, /* * Unsigned 32-bit value. Followed by a nested array of * EXTSCAN_CHANNEL_SPEC_* attributes. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, /* * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_* attributes. * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC = 13, /* Unsigned 32-bit value; base timer period in ms. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, /* * Unsigned 32-bit value; number of APs to store in each scan in the * BSSID/RSSI history buffer (keep the highest RSSI APs). */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, /* * Unsigned 8-bit value; in %, when scan buffer is this much full, wake * up AP. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT = 16, /* * Unsigned 8-bit value; number of scan bucket specs; followed by a * nested array of_EXTSCAN_BUCKET_SPEC_* attributes and values. The size * of the array is determined by NUM_BUCKETS. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, /* * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_* attributes. * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC = 18, /* Unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH = 19, /* Unsigned 32-bit value; maximum number of results to be returned. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX = 20, /* An array of 6 x unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_BSSID = 21, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, /* * Number of hotlist APs as unsigned 32-bit value, followed by a nested * array of AP_THRESHOLD_PARAM attributes and values. The size of the * array is determined by NUM_AP. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, /* * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_* attributes. * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM = 26, /* Unsigned 32-bit value; number of samples for averaging RSSI. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE = 27, /* Unsigned 32-bit value; number of samples to confirm AP loss. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE = 28, /* Unsigned 32-bit value; number of APs breaching threshold. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, /* * Unsigned 32-bit value; number of APs. Followed by an array of * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, /* Unsigned 32-bit value; number of samples to confirm AP loss. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE = 31, /* * Unsigned 32-bit value. If max_period is non zero or different than * period, then this bucket is an exponential backoff bucket. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_MAX_PERIOD = 32, /* Unsigned 32-bit value. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_BASE = 33, /* * Unsigned 32-bit value. For exponential back off bucket, number of * scans to perform for a given period. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_STEP_COUNT = 34, /* * Unsigned 8-bit value; in number of scans, wake up AP after these * many scans. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS = 35, /* * Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST sub command. */ /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE = 36, /* * Number of hotlist SSIDs as unsigned 32-bit value, followed by a * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The * size of the array is determined by NUM_SSID. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, /* * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_* * attributes. * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_NUM_SSID */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM = 38, /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_SSID = 39, /* Unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_BAND = 40, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, /* Unsigned 32-bit value; a bitmask with additional extscan config flag. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CONFIGURATION_FLAGS = 43, /* keep last */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_extscan_results { QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_INVALID = 0, /* * Unsigned 32-bit value; must match the request Id supplied by * Wi-Fi HAL in the corresponding subcmd NL msg. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_REQUEST_ID = 1, /* * Unsigned 32-bit value; used to indicate the status response from * firmware/driver for the vendor sub-command. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_STATUS = 2, /* * EXTSCAN Valid Channels attributes */ /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_CHANNELS = 3, /* * An array of NUM_CHANNELS x unsigned 32-bit value integers * representing channel numbers. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CHANNELS = 4, /* EXTSCAN Capabilities attributes */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN = 7, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE = 8, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD = 9, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS = 11, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES = 12, /* * EXTSCAN Attributes used with * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE sub-command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, /* * EXTSCAN attributes used with * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT sub-command. */ /* * An array of NUM_RESULTS_AVAILABLE x * QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_* */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST = 14, /* Unsigned 64-bit value; age of sample at the time of retrieval */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, /* 33 x unsigned 8-bit value; NULL terminated SSID */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_SSID = 16, /* An array of 6 x unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_BSSID = 17, /* Unsigned 32-bit value; channel frequency in MHz */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RSSI = 19, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RTT = 20, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, /* Unsigned 16-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, /* Unsigned 16-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, /* Unsigned 32-bit value; size of the IE DATA blob */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, /* * An array of IE_LENGTH x unsigned 8-bit value; blob of all the * information elements found in the beacon; this data should be a * packed list of wifi_information_element objects, one after the * other. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, /* * Unsigned 8-bit value; set by driver to indicate more scan results are * available. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, /* * EXTSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT sub-command. */ /* Unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_EVENT_TYPE = 27, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_EVENT_STATUS = 28, /* * EXTSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND sub-command. */ /* * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE * to indicate number of results. * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the * list of results. */ /* * EXTSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE sub-command. */ /* An array of 6 x unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL = 30, /* Unsigned 32-bit value. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI = 31, /* * A nested array of signed 32-bit RSSI values. Size of the array is * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST = 32, /* * EXTSCAN attributes used with * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS sub-command. */ /* * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE * to indicate number of extscan cached results returned. * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_LIST to indicate * the list of extscan cached results. */ /* * An array of NUM_RESULTS_AVAILABLE x * QCA_NL80211_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_* */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_LIST = 33, /* Unsigned 32-bit value; a unique identifier for the scan unit. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_SCAN_ID = 34, /* * Unsigned 32-bit value; a bitmask w/additional information about scan. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_FLAGS = 35, /* * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE * to indicate number of wifi scan results/bssids retrieved by the scan. * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the * list of wifi scan results returned for each cached result block. */ /* * EXTSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. */ /* * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE for * number of results. * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the nested * list of wifi scan results returned for each * wifi_passpoint_match_result block. * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE. */ /* * EXTSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES = 36, /* * A nested array of * QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_* * attributes. Array size = * *_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, /* Unsigned 32-bit value; network block id for the matched network */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, /* * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the nested * list of wifi scan results returned for each * wifi_passpoint_match_result block. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, /* * An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; * ANQP data in the information_element format. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID = 43, /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID = 44, QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_BUCKETS_SCANNED = 45, QCA_WLAN_VENDOR_ATTR_EXTSCAN_MAX_NUM_BLACKLISTED_BSSID = 46, /* keep last */ QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_MAX = QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_AFTER_LAST - 1, }; /** * enum qca_vendor_interop_issues_ap_type - interop issues type * This enum defines the valid set of values of interop issues type. These * values are used by attribute %QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE. * * @QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS: the ap has power save interop issue * when the STA's Qpower feature is enabled. */ enum qca_vendor_interop_issues_ap_type { QCA_VENDOR_INTEROP_ISSUES_AP_INVALID = 0, QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS = 1, }; /** * enum qca_vendor_attr_interop_issues_ap - attribute for ap with interop issues * values are used by %QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP. * * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE: interop issues type * 32-bit unsigned value, The type defined in enum * qca_vendor_interop_issues_ap_type are used. * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST: aps' bssid container * array of nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID attributes, * it is present and mandatory for the command but is not used for * the event since only a single BSSID is reported in an event. * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID: ap's bssid * 6-byte MAC address. It is used within the nested * QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST attribute in command case * and without such encapsulation in the event case. * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST: last value * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX: max value */ enum qca_vendor_attr_interop_issues_ap { QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID, QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE, QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST, QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID, /* keep last */ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX = QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST - 1 }; #ifdef WLAN_FEATURE_LINK_LAYER_STATS enum qca_wlan_vendor_attr_ll_stats_set { QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1, }; /** * qca_wlan_ll_stats_clr_req_bitmap - Represents the bitmap to clear LL STATS * values for %QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO: Clear all radio statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CCA: Clear cca_busy_time within * radio statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CHANNEL: Clear all channel * statistics within radio statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_SCAN: Clear all scan statistics within * radio statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE: Clear all interface statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_TXRATE: Clear all TX rate statistics * within interface statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_AC: Clear all AC statistics within * interface statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_CONTENTION: Clear all contention * (min, max, avg) statistics within AC statistics. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_ALL_PEER: Clear all peer statistics * on this interface. * * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_PER_PEER: Clear particular peer * statistics depending on the peer_mac. */ enum qca_wlan_ll_stats_clr_req_bitmap { QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO = BIT(0), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CCA = BIT(1), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CHANNELS = BIT(2), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_SCAN = BIT(3), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE = BIT(4), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_TXRATE = BIT(5), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_AC = BIT(6), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_CONTENTION = BIT(7), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_ALL_PEER = BIT(8), QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_PER_PEER = BIT(9), }; enum qca_wlan_vendor_attr_ll_stats_clr { QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, /* Unsigned 32bit bitmap for clearing statistics, specified * in the enum qca_wlan_ll_stats_clr_req_bitmap. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1, /* Unsigned 8 bit value: Request to stop statistics collection */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2, /* Unsigned 32 bit bitmap: Response from the driver * for the cleared statistics */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3, /* Unsigned 8 bit value: Response from driver/firmware * for the stop request */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1, }; /** * qca_wlan_ll_stats_get_req_bitmap - Represents the bitmap to request LL STATS * values for %QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK. * * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_RADIO: Request all radio statistics. * * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_IFACE: Request interface statistics. * * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_ALL_PEER: Request all peer statistics. * * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_PER_PEER: Request per peer statistics. */ enum qca_wlan_ll_stats_get_req_bitmap { QCA_WLAN_LL_STATS_GET_REQ_BITMAP_RADIO = BIT(0), QCA_WLAN_LL_STATS_GET_REQ_BITMAP_IFACE = BIT(1), QCA_WLAN_LL_STATS_GET_REQ_BITMAP_ALL_PEER = BIT(2), QCA_WLAN_LL_STATS_GET_REQ_BITMAP_PER_PEER = BIT(3), }; enum qca_wlan_vendor_attr_ll_stats_get { QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, /* Unsigned 32 bit value provided by the caller issuing the GET stats * command. When reporting the stats results, the driver uses the same * value to indicate which GET request the results correspond to. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1, /* Unsigned 32 bit value - bit mask to identify what statistics are * requested for retrieval specified in the enum * qca_wlan_ll_stats_get_req_bitmap */ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_ll_stats_results { QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, /* * For Multi Link Operation (MLO) connection, per-link statistics will * be sent inside of %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and * cumulative statistics will be sent outside of * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to maintain backward * compatibility with legacy user space. Attributes which don't have * explicit documentation for MLO will be sent only outside of * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK, such attributes values * don't depend on whether the connection is MLO capable or not, e.g., * radio and channel specific attributes. */ /* Unsigned 32bit value. Used by the driver; must match the request id * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are * nested within the interface stats. */ /* Interface mode, e.g., STA, SOFTAP, IBSS, etc. * Type = enum wifi_interface_mode. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, /* Interface MAC address. An array of 6 Unsigned int8 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, /* Type = enum wifi_connection_state, e.g., DISCONNECTED, * AUTHENTICATING, etc. valid for STA, CLI only. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, /* NULL terminated SSID. An array of 33 Unsigned 8bit values */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, /* For non-MLO connection, BSSID of the AP. For MLO connection, MLD * address of the AP. An array of 6 unsigned 8 bit values */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, /* Country string advertised by AP. An array of 3 unsigned 8 bit * values. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, /* Country string for this association. An array of 3 unsigned 8 bit * values. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could * be nested within the interface stats. * For an MLO connection, all %QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* * attributes except %QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_* * indicate the aggregate of all links outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. * %QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_* attributes * indicate value of the MLO link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. * These attributes indicate the link specific value inside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, /* Unsigned 32 bit value. Number of peers */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are * nested within the interface stats. */ /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, /* MAC addr corresponding to respective peer. An array of 6 unsigned * 8 bit values. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, /* Unsigned int 32 bit value representing capabilities corresponding * to respective peer. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, /* Unsigned 32 bit value. Number of rates */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* * are nested within the rate stat. */ /* Wi-Fi Rate - separate attributes defined for individual fields */ /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std * in the units of 0.5 Mbps HT/VHT it would be MCS index */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, /* Unsigned 32 bit value. Bit rate in units of 100 kbps */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be * nested within the peer info stats. */ /* Unsigned int 32 bit value. Number of successfully transmitted data * packets, i.e., with ACK received corresponding to the respective * rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, /* Unsigned int 32 bit value. Number of received data packets * corresponding to the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK * received corresponding to the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, /* Unsigned int 32 bit value. Total number of data packet retries for * the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, /* Unsigned int 32 bit value. Total number of short data packet retries * for the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, /* Unsigned int 32 bit value. Total number of long data packet retries * for the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, /* Unsigned 32 bit value. This is used to indicate radio ID of the radio * statistics when %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE is * %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO. This is also used * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to indicate radio ID * of the MLO link. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, /* Unsigned 32 bit value. Total number of msecs the radio is awake * accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, /* Unsigned 32 bit value. Total number of msecs the radio is * transmitting accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, /* Unsigned 32 bit value. Total number of msecs the radio is in active * receive accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to all scan accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to NAN accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to GSCAN accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to roam scan accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to PNO scan accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to Hotspot 2.0 scans and GAS exchange accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, /* Unsigned 32 bit value. Number of channels. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could * be nested within the channel stats. */ /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, /* Unsigned 32 bit value. Primary 20 MHz channel. This is used to * indicate the primary frequency of the channel when * %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE is * %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO. This is also used inside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to indicate the frequency * on which the MLO link is operating. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, /* Unsigned 32 bit value. Center frequency (MHz) first segment. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, /* Unsigned 32 bit value. Center frequency (MHz) second segment. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be * nested within the radio stats. */ /* Unsigned int 32 bit value representing total number of msecs the * radio is awake on that channel accruing over time, corresponding to * the respective channel. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, /* Unsigned int 32 bit value representing total number of msecs the CCA * register is busy accruing over time corresponding to the respective * channel. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, /* Signifies the nested list of channel attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, /* Signifies the nested list of peer info attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*. For MLO connection, * this also contains %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK_ID to * indicate on which link the peer is connected. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, /* Signifies the nested list of rate info attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, /* Signifies the nested list of wmm info attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates * that more stats, e.g., peers or radio, are to follow in the next * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. * Otherwise, it is set to 0. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, /* Unsigned 64 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, /* Number of msecs the radio spent in transmitting for each power level */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, /* Unsigned 32 bit value. For an MLO connection, indicates the value of * the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, /* Unsigned int 32 value. * Pending MSDUs corresponding to respective AC. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83, /* u32 value representing total time in milliseconds for which the radio * is transmitting on this channel. This attribute will be nested * within QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_TX_TIME = 84, /* u32 value representing total time in milliseconds for which the radio * is receiving all 802.11 frames intended for this device on this * channel. This attribute will be nested within * QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_RX_TIME = 85, /* u8 value representing the channel load percentage. Possible values * are 0-100. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_LOAD_PERCENTAGE = 86, /* u8 value representing the time slicing duty cycle percentage. * Possible values are 0-100. For an MLO connection, indicates the value * of the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_TS_DUTY_CYCLE = 87, /* Unsigned 32 bit value. The number of Beacon frames which are received * from the associated AP and indicate buffered unicast frame(s) for us * in the TIM element. For an MLO connection, indicates the value of the * link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON = 88, /* Unsigned 32 bit value. The total number of Beacon frames received * from the associated AP that have wrongly indicated buffered unicast * traffic in the TIM element for us. * Below scenarios will be considered as wrong TIM element beacon: * 1) The related TIM element is set in the beacon for STA but STA * doesn’t receive any unicast data after this beacon. * 2) The related TIM element is still set in the beacon for STA * after STA has indicated power save exit by QoS Null Data frame. * For an MLO connection, indicates the value of the link with the best * RSSI outside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link * specific value inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON_ERR = 89, /* Signed 32 bit value. It represents the noise floor calibration value. * Possible values are -120~-50 dBm. For an MLO connection, indicates * the value of the link with the best RSSI outside * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NF_CAL_VAL = 90, /* Attribute used for padding for 64-bit alignment */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD = 91, /* Unsigned u8 value, link ID of an MLO link. Used inside nested * attribute %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to represent the * link ID of the MLO link for which the statistics are embedded in the * nested attribute. Used inside nested attribute * %QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO to represent the connected * link ID of the peer. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK_ID = 92, /* A nested array of attributes for each MLO link, each containing * per-link statistics of a multi link connection. The attributes used * inside this nested attribute are defined in enum * qca_wlan_vendor_attr_ll_stats_results. * * For non-MLO connection, this attribute is not present and the * statistics will be sent outside this attribute (without nesting). * * For MLO connection, this attribute is present and also cumulative * statistics of all the links will be sent outside of this attribute * to be compatible with legacy user space. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK = 93, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_ll_stats_type { QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, /* keep last */ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, }; #endif /* WLAN_FEATURE_LINK_LAYER_STATS */ /** * enum qca_wlan_vendor_attr_get_supported_features - get supported feature * * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET: Unsigned 32bit value * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX: Max value */ enum qca_wlan_vendor_attr_get_supported_features { QCA_WLAN_VENDOR_ATTR_FEATURE_SET_INVALID = 0, QCA_WLAN_VENDOR_ATTR_FEATURE_SET = 1, QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX = QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_set_scanning_mac_oui - set scanning mac oui * * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI: An array of 3 x Unsigned 8-bit * value * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_MAX: Max value */ enum qca_wlan_vendor_attr_set_scanning_mac_oui { QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI = 1, QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_MAX = QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_scan_priority - Specifies the valid values that the * vendor scan attribute QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY can take. * @QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_LOW: Very low priority * @QCA_WLAN_VENDOR_SCAN_PRIORITY_LOW: Low priority * @QCA_WLAN_VENDOR_SCAN_PRIORITY_MEDIUM: Medium priority * @QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH: High priority * @QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_HIGH: Very high priority */ enum qca_wlan_vendor_scan_priority { QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_LOW = 0, QCA_WLAN_VENDOR_SCAN_PRIORITY_LOW = 1, QCA_WLAN_VENDOR_SCAN_PRIORITY_MEDIUM = 2, QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH = 3, QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_HIGH = 4, }; /** * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes * * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes * with frequencies to be scanned (in MHz) * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported * rates to be included * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests * at non CCK rate in 2GHz band * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the * driver for the specific scan request * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan * request decoded as in enum scan_status * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation * scan flag is set * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with * randomisation * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the * specific BSSID to scan for. * @QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME: Unsigned 64-bit dwell time in * microseconds. This is a common value which applies across all * frequencies specified by QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES. * @QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY: Priority of vendor scan relative to * other scan requests. It is a u32 attribute and takes values from enum * qca_wlan_vendor_scan_priority. This is an optional attribute. * If this attribute is not configured, the driver shall use * QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH as the priority of vendor scan. */ enum qca_wlan_vendor_attr_scan { QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1, QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2, QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3, QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4, QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5, QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6, QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7, QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8, QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9, QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10, QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11, QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME = 12, QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY = 13, QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SCAN_MAX = QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 }; /** * enum scan_status - Specifies the valid values the vendor scan attribute * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with * new scan results * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between */ enum scan_status { VENDOR_SCAN_STATUS_NEW_RESULTS, VENDOR_SCAN_STATUS_ABORTED, VENDOR_SCAN_STATUS_MAX, }; /** * enum qca_wlan_vendor_attr_get_concurrency_matrix - get concurrency matrix * * NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX sub command. * * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_CONFIG_PARAM_SET_SIZE_MAX: * Unsigned 32-bit value * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET_SIZE: * Unsigned 32-bit value * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET: Set results. An * array of SET_SIZE x Unsigned 32bit values representing concurrency * combinations * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_MAX: Max value */ enum qca_wlan_vendor_attr_get_concurrency_matrix { QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_INVALID = 0, QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_CONFIG_PARAM_SET_SIZE_MAX = 1, QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET_SIZE = 2, QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET = 3, QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_MAX = QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_set_no_dfs_flag - vendor attribute set no dfs flag * * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG: Unsigned 32-bit value * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_MAX: Max value */ enum qca_wlan_vendor_attr_set_no_dfs_flag { QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG = 1, QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_MAX = QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST - 1, }; /** * enum qca_vendor_attr_wisa_cmd * @QCA_WLAN_VENDOR_ATTR_WISA_INVALID: Invalid attr * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value attr (u32) * @QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_WISA_MAX: Max Value * WISA setup vendor commands */ enum qca_vendor_attr_wisa_cmd { QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WISA_MODE, QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WISA_MAX = QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 }; enum qca_roaming_policy { QCA_ROAMING_NOT_ALLOWED, QCA_ROAMING_ALLOWED_WITHIN_ESS, }; /** * enum qca_roam_reason - Represents the reason codes for roaming. Used by * QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON. * * @QCA_ROAM_REASON_UNKNOWN: Any reason that do not classify under the below * reasons. * * @QCA_ROAM_REASON_PER: Roam triggered when packet error rates(PER) breached * the configured threshold. * * @QCA_ROAM_REASON_BEACON_MISS: Roam triggered due to the continuous configured * beacon misses from the then connected AP. * * @QCA_ROAM_REASON_POOR_RSSI: Roam triggered due to the poor RSSI reported * by the connected AP. * * @QCA_ROAM_REASON_BETTER_RSSI: Roam triggered for finding a BSSID with a * better RSSI than the connected BSSID. Here the RSSI of the current BSSID is * not poor. * * @QCA_ROAM_REASON_CONGESTION: Roam triggered considering the connected channel * or environment being very noisy / congested. * * @QCA_ROAM_REASON_EXPLICIT_REQUEST: Roam triggered due to an explicit request * from the user (user space). * * @QCA_ROAM_REASON_BTM: Roam triggered due to BTM request frame received from * connected AP. * * @QCA_ROAM_REASON_BSS_LOAD: Roam triggered due to the channel utilization * breaching out the configured threshold. * * @QCA_ROAM_REASON_WTC: Roam triggered due to Wireless to Cellular BSS * transition request. * * @QCA_ROAM_REASON_IDLE: Roam triggered when device is suspended, * there is no data activity with the AP and the current rssi falls below a * certain threshold. * * @QCA_ROAM_REASON_DISCONNECTION: Roam triggered due to * deauthentication or disassociation frames received from the connected AP. * * @QCA_ROAM_REASON_PERIODIC_TIMER: Roam triggered as part of the periodic * scan that happens when there is no candidate AP found during the poor * RSSI scan trigger. * * @QCA_ROAM_REASON_BACKGROUND_SCAN: Roam triggered based on the scan * results obtained from an external scan (not aimed at roaming). * * @QCA_ROAM_REASON_BT_ACTIVITY: Roam triggered due to bluetooth * connection is established when the station is connected in 2.4 Ghz band. * * @QCA_ROAM_REASON_STA_KICKOUT: Roam triggered due to continuous TX Data frame * failures to the connected AP. */ enum qca_roam_reason { QCA_ROAM_REASON_UNKNOWN, QCA_ROAM_REASON_PER, QCA_ROAM_REASON_BEACON_MISS, QCA_ROAM_REASON_POOR_RSSI, QCA_ROAM_REASON_BETTER_RSSI, QCA_ROAM_REASON_CONGESTION, QCA_ROAM_REASON_USER_TRIGGER, QCA_ROAM_REASON_BTM, QCA_ROAM_REASON_BSS_LOAD, QCA_ROAM_REASON_WTC, QCA_ROAM_REASON_IDLE, QCA_ROAM_REASON_DISCONNECTION, QCA_ROAM_REASON_PERIODIC_TIMER, QCA_ROAM_REASON_BACKGROUND_SCAN, QCA_ROAM_REASON_BT_ACTIVITY, QCA_ROAM_REASON_STA_KICKOUT, }; /** * enum qca_wlan_vendor_attr_roam_auth - vendor event for roaming * * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE: Request IE * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE: Response IE * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED: Authorization Status * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR: Replay Counter * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK: KCK of the PTK * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK: KEK of the PTK * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS: subnet change status * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS: * Indicates the status of re-association requested by user space for * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. * Type u16. * Represents the status code from AP. Use * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the * real status code for failures. * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION: * This attribute indicates that the old association was maintained when * a re-association is requested by user space and that re-association * attempt fails (i.e., cannot connect to the requested BSS, but can * remain associated with the BSS with which the association was in * place when being requested to roam). Used along with * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current * re-association status. Type flag. * This attribute is applicable only for re-association failure cases. * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK: AUTH PMK * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID: AUTH PMKID * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM: FILS erp next * seq number * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON: A 16-bit unsigned value * representing the reasons for the roaming. Defined by enum * qca_roam_reason. */ enum qca_wlan_vendor_attr_roam_auth { QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, /* Indicates BSSID of the roamed AP for non-MLO roaming and MLD address * of the roamed AP for MLO roaming. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON, /* A nested attribute containing per-link information of all the links * of MLO connection done while roaming. The attributes used inside this * nested attribute are defined in enum qca_wlan_vendor_attr_mlo_links. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MLO_LINKS = 15, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_mlo_links - Definition of attributes used inside * nested attribute QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MLO_LINKS. * * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_ID: u8 attribute, link ID of this MLO link. * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_MAC_ADDR: Own MAC address of this MLO link. * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_BSSID: AP link MAC address of this MLO link. */ enum qca_wlan_vendor_attr_mlo_links { QCA_WLAN_VENDOR_ATTR_MLO_LINK_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MLO_LINK_ID = 1, QCA_WLAN_VENDOR_ATTR_MLO_LINK_MAC_ADDR = 2, QCA_WLAN_VENDOR_ATTR_MLO_LINK_BSSID = 3, /* Keep last */ QCA_WLAN_VENDOR_ATTR_MLO_LINK_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MLO_LINK_MAX = QCA_WLAN_VENDOR_ATTR_MLO_LINK_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_wifi_config - wifi config * * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_DYNAMIC_DTIM: dynamic DTIM * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_STATS_AVG_FACTOR: avg factor * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_GUARD_TIME: guard time * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST: after last * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_MAX: max value */ enum qca_wlan_vendor_attr_wifi_config { QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_DYNAMIC_DTIM = 1, QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_STATS_AVG_FACTOR = 2, QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_GUARD_TIME = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_epno_type - the type of request to the EPNO command * @QCA_WLAN_EPNO: epno type request * @QCA_WLAN_PNO: pno type request */ enum qca_wlan_epno_type { QCA_WLAN_EPNO, QCA_WLAN_PNO }; /** * enum qca_wlan_vendor_attr_pno_config_params - pno config params * * @QCA_WLAN_VENDOR_ATTR_PNO_INVALID - Invalid initial value * * NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM: * Unsigned 32-bit value; pno passpoint number of networks * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY: * Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* * attributes. Array size = * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID: * Unsigned 32-bit value; network id * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM: * An array of 256 x Unsigned 8-bit value; NULL terminated UTF8 encoded * realm, 0 if unspecified. * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID: * An array of 16 x Unsigned 32-bit value; roaming consortium ids * to match, 0 if unspecified. * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN: * An array of 6 x Unsigned 8-bit value; mcc/mnc combination, 0s if * unspecified. * * NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS: * Unsigned 32-bit value; set pno number of networks * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST: * Array of nested * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* * attributes. Array size = * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID: * An array of 33 x Unsigned 8-bit value; NULL terminated SSID * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD: * Signed 8-bit value; threshold for considering this SSID as found, * required granularity for this threshold is 4dBm to 8dBm * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS: * Unsigned 8-bit value; WIFI_PNO_FLAG_XXX * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT: * Unsigned 8-bit value; auth bit field for matching WPA IE * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE * Unsigned 8-bit to indicate ePNO type; values from qca_wlan_epno_type *@QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST * Nested attribute to send the channel list *@QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL * Unsigned 32-bit value; indicates the Interval between PNO scan * cycles in msec *@QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI * Signed 32-bit value; minimum 5GHz RSSI for a BSSID to be considered *@QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI * Signed 32-bit value; minimum 2.4GHz RSSI for a BSSID to be considered * This attribute is obsolete now. *@QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX * Signed 32-bit value; the maximum score that a network * can have before bonuses *@QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS * Signed 32-bit value; only report when there is a network's * score this much higher han the current connection *@QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS * Signed 32-bit value; score bonus for all networks with * the same network flag *@QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS * Signed 32-bit value; score bonus for networks that are not open *@QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS * Signed 32-bit value; 5GHz RSSI score bonus applied to all * 5GHz networks *@QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID * Unsigned 32-bit value, representing the PNO Request ID * @QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_PNO_MAX: max */ enum qca_wlan_vendor_attr_pno_config_params { QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD = 10, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, /* keep last */ QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PNO_MAX = QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, }; /** * enum qca_scan_freq_list_type: Frequency list types * * @QCA_PREFERRED_SCAN_FREQ_LIST: The driver shall use the scan frequency list * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as * a preferred frequency list for roaming. * * @QCA_SPECIFIC_SCAN_FREQ_LIST: The driver shall use the frequency list * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as * a specific frequency list for roaming. */ enum qca_scan_freq_list_type { QCA_PREFERRED_SCAN_FREQ_LIST = 1, QCA_SPECIFIC_SCAN_FREQ_LIST = 2, }; /** * enum qca_roam_scan_scheme: scan scheme * * @QCA_ROAM_SCAN_SCHEME_NO_SCAN: No Frequencies specified to scan. * Indicates the driver to not scan on a Roam Trigger scenario, but * Disconnect.e.g., On a BTM request from the AP driver/firmware shall * disconnect from the current connected AP by notifying a failure * code in the BTM response. * * @QCA_ROAM_SCAN_SCHEME_PARTIAL_SCAN: Indicates the driver/firmware to * trigger partial frequency scans. These frequencies are the ones learnt * or maintained by the driver based on the probability of finding the * BSSID's in the ESS for which the roaming is triggered. * * @QCA_ROAM_SCAN_SCHEME_FULL_SCAN: Indicates the driver/firmware to * trigger the scan on all the valid frequencies to find the better * candidates to roam. */ enum qca_roam_scan_scheme { QCA_ROAM_SCAN_SCHEME_NO_SCAN = 0, QCA_ROAM_SCAN_SCHEME_PARTIAL_SCAN = 1, QCA_ROAM_SCAN_SCHEME_FULL_SCAN = 2, }; /** * enum qca_vendor_attr_scan_freq_list_scheme: Frequency list scheme * * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST: An array of unsigned 32-bit values. * List of frequencies in MHz to be considered for a roam scan. * * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE: Unsigned 32-bit value. * Type of frequency list scheme being configured/gotten as defined by the * enum qca_scan_freq_list_type. */ enum qca_vendor_attr_scan_freq_list_scheme { QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST = 1, QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE = 2, /* keep last */ QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST, QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_MAX = QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST - 1, }; /* * enum qca_vendor_roam_triggers: Bitmap of roaming triggers * * @QCA_ROAM_TRIGGER_REASON_PER: Set if the roam has to be triggered based on * a bad packet error rates (PER). * @QCA_ROAM_TRIGGER_REASON_BEACON_MISS: Set if the roam has to be triggered * based on beacon misses from the connected AP. * @QCA_ROAM_TRIGGER_REASON_POOR_RSSI: Set if the roam has to be triggered * due to poor RSSI of the connected AP. * @QCA_ROAM_TRIGGER_REASON_BETTER_RSSI: Set if the roam has to be triggered * upon finding a BSSID with a better RSSI than the connected BSSID. * Also, set if the roam has to be triggered due to the high RSSI of the * current connected AP (better than * QCA_ATTR_ROAM_CONTROL_CONNECTED_HIGH_RSSI_OFFSET). Here the RSSI of * the current BSSID need not be poor. * @QCA_ROAM_TRIGGER_REASON_PERIODIC: Set if the roam has to be triggered * by triggering a periodic scan to find a better AP to roam. * @QCA_ROAM_TRIGGER_REASON_DENSE: Set if the roam has to be triggered * when the connected channel environment is too noisy/congested. * @QCA_ROAM_TRIGGER_REASON_BTM: Set if the roam has to be triggered * when BTM Request frame is received from the connected AP. * @QCA_ROAM_TRIGGER_REASON_BSS_LOAD: Set if the roam has to be triggered * when the channel utilization is goes above the configured threshold. * @QCA_ROAM_TRIGGER_REASON_USER_TRIGGER: Set if the roam has to be triggered * based on the request from the user (space). * @QCA_ROAM_TRIGGER_REASON_DEAUTH: Set if the roam has to be triggered when * device receives Deauthentication/Disassociation frame from connected * AP. * @QCA_ROAM_TRIGGER_REASON_IDLE: Set if the roam has to be triggered when the * DUT is in idle state (no tx/rx) and suspend mode, if the current RSSI * is determined to be a poor one. * @QCA_ROAM_TRIGGER_REASON_TX_FAILURES: Set if the roam has to be triggered * based on continuous TX Data Frame failures to the connected AP. * @QCA_ROAM_TRIGGER_REASON_EXTERNAL_SCAN: Set if the roam has to be triggered * based on the scan results obtained from an external scan (not * triggered to aim roaming) * * Set the corresponding roam trigger reason bit to consider it for roam * trigger. * Userspace can set multiple bits and send to the driver. The driver shall * consider all of them to trigger/initiate a roam scan. */ enum qca_vendor_roam_triggers { QCA_ROAM_TRIGGER_REASON_PER = 1 << 0, QCA_ROAM_TRIGGER_REASON_BEACON_MISS = 1 << 1, QCA_ROAM_TRIGGER_REASON_POOR_RSSI = 1 << 2, QCA_ROAM_TRIGGER_REASON_BETTER_RSSI = 1 << 3, QCA_ROAM_TRIGGER_REASON_PERIODIC = 1 << 4, QCA_ROAM_TRIGGER_REASON_DENSE = 1 << 5, QCA_ROAM_TRIGGER_REASON_BTM = 1 << 6, QCA_ROAM_TRIGGER_REASON_BSS_LOAD = 1 << 7, QCA_ROAM_TRIGGER_REASON_USER_TRIGGER = 1 << 8, QCA_ROAM_TRIGGER_REASON_DEAUTH = 1 << 9, QCA_ROAM_TRIGGER_REASON_IDLE = 1 << 10, QCA_ROAM_TRIGGER_REASON_TX_FAILURES = 1 << 11, QCA_ROAM_TRIGGER_REASON_EXTERNAL_SCAN = 1 << 12, }; /* * enum qca_vendor_roam_fail_reasons: Defines the various roam * fail reasons. This enum value is used in * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON attribute. * * @QCA_ROAM_FAIL_REASON_SCAN_NOT_ALLOWED: Roam module in the firmware is not * able to trigger the scan. * @QCA_ROAM_FAIL_REASON_NO_AP_FOUND: No roamable APs found during roam scan. * @QCA_ROAM_FAIL_REASON_NO_CAND_AP_FOUND: No candidate APs found during roam * scan. * @QCA_ROAM_FAIL_REASON_HOST: Roam fail due to disconnect issued from host. * @QCA_ROAM_FAIL_REASON_AUTH_SEND: Unable to send Authentication frame. * @QCA_ROAM_FAIL_REASON_AUTH_RECV: Received Authentication frame with error * status code. * @QCA_ROAM_FAIL_REASON_NO_AUTH_RESP: Authentication frame not received. * @QCA_ROAM_FAIL_REASON_REASSOC_SEND: Unable to send Reassociation Request * frame. * @QCA_ROAM_FAIL_REASON_REASSOC_RECV: Received Reassociation Response frame * with error status code. * @QCA_ROAM_FAIL_REASON_NO_REASSOC_RESP: Reassociation Response frame not * received. * @QCA_ROAM_FAIL_REASON_SCAN_FAIL: Scan module not able to start scan. * @QCA_ROAM_FAIL_REASON_AUTH_NO_ACK: No ACK is received for Authentication * frame. * @QCA_ROAM_FAIL_REASON_AUTH_INTERNAL_DROP: Authentication frame is dropped * internally before transmission. * @QCA_ROAM_FAIL_REASON_REASSOC_NO_ACK: No ACK is received for Reassociation * Request frame. * @QCA_ROAM_FAIL_REASON_REASSOC_INTERNAL_DROP: Reassociation Request frame is * dropped internally. * @QCA_ROAM_FAIL_REASON_EAPOL_M1_TIMEOUT: EAPOL-Key M1 is not received and * times out. * @QCA_ROAM_FAIL_REASON_EAPOL_M2_SEND: Unable to send EAPOL-Key M2 frame. * @QCA_ROAM_FAIL_REASON_EAPOL_M2_INTERNAL_DROP: EAPOL-Key M2 frame dropped * internally. * @QCA_ROAM_FAIL_REASON_EAPOL_M2_NO_ACK: No ACK is received for EAPOL-Key * M2 frame. * @QCA_ROAM_FAIL_REASON_EAPOL_M3_TIMEOUT: EAPOL-Key M3 frame is not received. * @QCA_ROAM_FAIL_REASON_EAPOL_M4_SEND: Unable to send EAPOL-Key M4 frame. * @QCA_ROAM_FAIL_REASON_EAPOL_M4_INTERNAL_DROP: EAPOL-Key M4 frame dropped * internally. * @QCA_ROAM_FAIL_REASON_EAPOL_M4_NO_ACK: No ACK is received for EAPOL-Key M4 * frame. * @QCA_ROAM_FAIL_REASON_NO_SCAN_FOR_FINAL_BEACON_MISS: Roam scan is not * started for final beacon miss case. * @QCA_ROAM_FAIL_REASON_DISCONNECT: Deauthentication or Disassociation frame * received from the AP during roaming handoff. * @QCA_ROAM_FAIL_REASON_RESUME_ABORT: Firmware roams to the AP when the Apps * or host is suspended and gives the indication of the last roamed AP only * when the Apps is resumed. If the Apps is resumed while the roaming is in * progress, this ongoing roaming is aborted and the last roamed AP is * indicated to host. * @QCA_ROAM_FAIL_REASON_SAE_INVALID_PMKID: WPA3-SAE invalid PMKID. * @QCA_ROAM_FAIL_REASON_SAE_PREAUTH_TIMEOUT: WPA3-SAE pre-authentication times * out. * @QCA_ROAM_FAIL_REASON_SAE_PREAUTH_FAIL: WPA3-SAE pre-authentication fails. * @QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK: Roam scan did not happen since the * current network conditions are fine. */ enum qca_vendor_roam_fail_reasons { QCA_ROAM_FAIL_REASON_NONE = 0, QCA_ROAM_FAIL_REASON_SCAN_NOT_ALLOWED = 1, QCA_ROAM_FAIL_REASON_NO_AP_FOUND = 2, QCA_ROAM_FAIL_REASON_NO_CAND_AP_FOUND = 3, QCA_ROAM_FAIL_REASON_HOST = 4, QCA_ROAM_FAIL_REASON_AUTH_SEND = 5, QCA_ROAM_FAIL_REASON_AUTH_RECV = 6, QCA_ROAM_FAIL_REASON_NO_AUTH_RESP = 7, QCA_ROAM_FAIL_REASON_REASSOC_SEND = 8, QCA_ROAM_FAIL_REASON_REASSOC_RECV = 9, QCA_ROAM_FAIL_REASON_NO_REASSOC_RESP = 10, QCA_ROAM_FAIL_REASON_SCAN_FAIL = 11, QCA_ROAM_FAIL_REASON_AUTH_NO_ACK = 12, QCA_ROAM_FAIL_REASON_AUTH_INTERNAL_DROP = 13, QCA_ROAM_FAIL_REASON_REASSOC_NO_ACK = 14, QCA_ROAM_FAIL_REASON_REASSOC_INTERNAL_DROP = 15, QCA_ROAM_FAIL_REASON_EAPOL_M1_TIMEOUT = 16, QCA_ROAM_FAIL_REASON_EAPOL_M2_SEND = 17, QCA_ROAM_FAIL_REASON_EAPOL_M2_INTERNAL_DROP = 18, QCA_ROAM_FAIL_REASON_EAPOL_M2_NO_ACK = 19, QCA_ROAM_FAIL_REASON_EAPOL_M3_TIMEOUT = 20, QCA_ROAM_FAIL_REASON_EAPOL_M4_SEND = 21, QCA_ROAM_FAIL_REASON_EAPOL_M4_INTERNAL_DROP = 22, QCA_ROAM_FAIL_REASON_EAPOL_M4_NO_ACK = 23, QCA_ROAM_FAIL_REASON_NO_SCAN_FOR_FINAL_BEACON_MISS = 24, QCA_ROAM_FAIL_REASON_DISCONNECT = 25, QCA_ROAM_FAIL_REASON_RESUME_ABORT = 26, QCA_ROAM_FAIL_REASON_SAE_INVALID_PMKID = 27, QCA_ROAM_FAIL_REASON_SAE_PREAUTH_TIMEOUT = 28, QCA_ROAM_FAIL_REASON_SAE_PREAUTH_FAIL = 29, QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK = 30, }; /* * enum qca_vendor_roam_invoke_fail_reasons: Defines the various roam * invoke fail reasons. This enum value is used in * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON attribute. * * @QCA_ROAM_INVOKE_STATUS_IFACE_INVALID: Invalid interface ID is passed * in roam invoke command. * @QCA_ROAM_INVOKE_STATUS_OFFLOAD_DISABLE: Roam offload in firmware is not * enabled. * @QCA_ROAM_INVOKE_STATUS_AP_SSID_LENGTH_INVALID: Connected AP profile SSID * length is invalid. * @QCA_ROAM_INVOKE_STATUS_ROAM_DISALLOW: Firmware internal roaming is already * in progress. * @QCA_ROAM_INVOKE_STATUS_NON_ROAMABLE_AP: Host sends the Beacon/Probe Response * of the AP in the roam invoke command to firmware. This reason is sent by the * firmware when the given AP is configured to be ignored or SSID/security * does not match. * @QCA_ROAM_INVOKE_STATUS_ROAM_INTERNAL_FAIL: Roam handoff failed because of * firmware internal reasons. * @QCA_ROAM_INVOKE_STATUS_DISALLOW: Roam invoke trigger is not enabled. * @QCA_ROAM_INVOKE_STATUS_SCAN_FAIL: Scan start fail for roam invoke. * @QCA_ROAM_INVOKE_STATUS_START_ROAM_FAIL: Roam handoff start fail. * @QCA_ROAM_INVOKE_STATUS_INVALID_PARAMS: Roam invoke parameters are invalid. * @QCA_ROAM_INVOKE_STATUS_NO_CAND_AP: No candidate AP found to roam to. * @QCA_ROAM_INVOKE_STATUS_ROAM_FAIL: Roam handoff failed. */ enum qca_vendor_roam_invoke_fail_reasons { QCA_ROAM_INVOKE_STATUS_NONE = 0, QCA_ROAM_INVOKE_STATUS_IFACE_INVALID = 1, QCA_ROAM_INVOKE_STATUS_OFFLOAD_DISABLE = 2, QCA_ROAM_INVOKE_STATUS_AP_SSID_LENGTH_INVALID = 3, QCA_ROAM_INVOKE_STATUS_ROAM_DISALLOW = 4, QCA_ROAM_INVOKE_STATUS_NON_ROAMABLE_AP = 5, QCA_ROAM_INVOKE_STATUS_ROAM_INTERNAL_FAIL = 6, QCA_ROAM_INVOKE_STATUS_DISALLOW = 7, QCA_ROAM_INVOKE_STATUS_SCAN_FAIL = 8, QCA_ROAM_INVOKE_STATUS_START_ROAM_FAIL = 9, QCA_ROAM_INVOKE_STATUS_INVALID_PARAMS = 10, QCA_ROAM_INVOKE_STATUS_NO_CAND_AP = 11, QCA_ROAM_INVOKE_STATUS_ROAM_FAIL = 12, }; /** * enum qca_vendor_attr_roam_candidate_selection_criteria: * * Each attribute carries a weightage in percentage (%). * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI: Unsigned 8-bit value. * Represents the weightage to be given for the RSSI selection * criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE: Unsigned 8-bit value. * Represents the weightage to be given for the rate selection * criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW: Unsigned 8-bit value. * Represents the weightage to be given for the band width selection * criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND: Unsigned 8-bit value. * Represents the weightage to be given for the band selection * criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS: Unsigned 8-bit value. * Represents the weightage to be given for the NSS selection * criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION: Unsigned 8-bit value. * Represents the weightage to be given for the channel congestion * selection criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING: Unsigned 8-bit value. * Represents the weightage to be given for the beamforming selection * criteria among other parameters. * * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN: Unsigned 8-bit value. * Represents the weightage to be given for the OCE selection * criteria among other parameters. */ enum qca_vendor_attr_roam_candidate_selection_criteria { QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI = 1, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE = 2, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW = 3, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND = 4, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS = 5, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION = 6, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING = 7, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN = 8, /* keep last */ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST, QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_MAX = QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST - 1, }; /** * enum qca_vendor_attr_roam_control - Attributes to carry roam configuration * The following attributes are used to set/get/clear the respective * configurations to/from the driver. * For the get, the attribute for the configuration to be queried shall * carry any of its acceptable values to the driver. In return, the driver * shall send the configured values within the same attribute to the user * space. * * @QCA_ATTR_ROAM_CONTROL_ENABLE: Unsigned 8-bit value. * Signifies to enable/disable roam control in driver. * 1-enable, 0-disable * Enable: Mandates the driver to do the further roams using the * configuration parameters set through * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. * Disable: Disables the driver/firmware roaming triggered through * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. Further roaming is * expected to continue with the default configurations. * * @QCA_ATTR_ROAM_CONTROL_STATUS: Unsigned 8-bit value. * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET. * Roam control status is obtained through this attribute. * * @QCA_ATTR_ROAM_CONTROL_CLEAR_ALL: Flag attribute to indicate the * complete config set through QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET * is to be cleared in the driver. * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR * and shall be ignored if used with other sub commands. * If this attribute is specified along with subcmd * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR, the driver shall ignore * all other attributes, if there are any. * If this attribute is not specified when the subcmd * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR is sent, the driver shall * clear the data corresponding to the attributes specified. * * @QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME: Nested attribute to carry the * list of frequencies and its type, represented by * enum qca_vendor_attr_scan_freq_list_scheme. * Frequency list and its type are mandatory for this attribute to set * the frequencies. * Frequency type is mandatory for this attribute to get the frequencies * and the frequency list is obtained through * QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST. * Frequency list type is mandatory for this attribute to clear the * frequencies. * * @QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD: Unsigned 32-bit value. * Carries the value of scan period in seconds to set. * The value of scan period is obtained with the same attribute for get. * Clears the scan period in the driver when specified with clear command. * Scan period is the idle time in seconds between each subsequent * channel scans. * * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD: Unsigned 32-bit value. * Carries the value of full scan period in seconds to set. * The value of full scan period is obtained with the same attribute for * get. * Clears the full scan period in the driver when specified with clear * command. Full scan period is the idle period in seconds between two * successive full channel roam scans. * * @QCA_ATTR_ROAM_CONTROL_TRIGGERS: Unsigned 32-bit value. * Carries a bitmap of the roam triggers specified in * enum qca_vendor_roam_triggers. * The driver shall enable roaming by enabling corresponding roam triggers * based on the trigger bits sent with this attribute. * If this attribute is not configured, the driver shall proceed with * default behavior. * The bitmap configured is obtained with the same attribute for get. * Clears the bitmap configured in driver when specified with clear * command. * * @QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA: Nested attribute signifying the * weightage in percentage (%) to be given for each selection criteria. * Different roam candidate selection criteria are represented by * enum qca_vendor_attr_roam_candidate_selection_criteria. * The driver shall select the roam candidate based on corresponding * candidate selection scores sent. * * An empty nested attribute is used to indicate that no specific * preference score/criteria is configured (i.e., to disable this mechanism * in the set case and to show that the mechanism is disabled in the get * case). * * Userspace can send multiple attributes out of this enum to the driver. * Since this attribute represents the weight/percentage of preference for * the respective selection criteria, it is preferred to configure 100% * total weightage. The value in each attribute or cumulative weight of the * values in all the nested attributes should not exceed 100%. The driver * shall reject such configuration. * * If the weights configured through this attribute are less than 100%, * the driver shall honor the weights (x%) passed for the corresponding * selection criteria and choose/distribute rest of the weight (100-x)% * for the other selection criteria, based on its internal logic. * * The selection criteria configured is obtained with the same * attribute for get. * * Clears the selection criteria configured in the driver when specified * with clear command. * * @QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME: Unsigned 32-bit value. * Represents value of scan frequency scheme from * enum qca_roam_scan_scheme. * * @QCA_ATTR_ROAM_CONTROL_CONNECTED_RSSI_THRESHOLD: Signed 32-bit value in dBm, * signifying the RSSI threshold of the current connected AP, indicating * the driver to trigger roam only when the current connected AP's RSSI * is lesser than this threshold. * * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD: Signed 32-bit value in dBm, * signifying the RSSI threshold of the candidate AP, indicating * the driver to trigger roam only to the candidate AP with RSSI * better than this threshold. If RSSI thresholds for candidate APs found * in the 2.4GHz, 5GHz and 6Ghz bands are configured separately using * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ, * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ, and/or * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ, then those values * will take precedence over the value configured using * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute. * * @QCA_ATTR_ROAM_CONTROL_USER_REASON: Unsigned 32-bit value. Represents the * user triggered reason code to be sent to the AP in response to AP's * request to trigger the roam if the roaming cannot be triggered. * Applies to all the scenarios of AP assisted roaming (e.g., BTM). * * @QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS: Unsigned 32-bit value. * Carries a bitmap of the roam triggers specified in * enum qca_vendor_roam_triggers. * Represents the roam triggers for which the specific scan scheme from * enum qca_roam_scan_scheme has to be applied. * It's an optional attribute. If this attribute is not configured, but * QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME is specified, then the scan scheme * specified through QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME is applicable for * all the roams. * If both QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME and * QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS are not specified, the * driver shall proceed with the default behavior. * * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ: Signed 32-bit value * in dBm, signifying the RSSI threshold of the candidate AP found in * 2.4GHz band. The driver/firmware shall trigger roaming to the candidate * AP found in 2.4GHz band only if it's RSSI value is better than this * threshold. Optional attribute. If this attribute is not included, then * threshold value specified by the * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. * * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ: Signed 32-bit value in * dBm, signifying the RSSI threshold of the candidate AP found in 5GHz * band. The driver/firmware shall trigger roaming to the candidate AP * found in 5GHz band only if it's RSSI value is better than this * threshold. Optional attribute. If this attribute is not included, then * threshold value specified by the * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. * * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ: Signed 32-bit value in * dBm, signifying the RSSI threshold of the candidate AP found in 6GHz * band. The driver/firmware shall trigger roaming to the candidate AP * found in 6GHz band only if it's RSSI value is better than this * threshold. Optional attribute. If this attribute is not included, then * threshold value specified by the * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. * * @QCA_ATTR_ROAM_CONTROL_BAND_MASK: Unsigned 32-bit value. * Carries bitmask value of bits from &enum qca_set_band and represents * all the bands in which roaming is allowed. The configuration is valid * until next disconnection. If this attribute is not present, the * existing configuration shall be used. By default, roaming is allowed * on all bands supported by local device. When the value is set to * %QCA_SETBAND_AUTO, all supported bands shall be enabled. * * @QCA_ATTR_ROAM_CONTROL_RX_LINKSPEED_THRESHOLD: u16 value in Mbps. * Optional parameter. RX link speed threshold to disable roaming. * If the current RX link speed is above the threshold, roaming is not * needed. If this attribute is not configured, or if it is set to 0, the * driver will not consider the RX link speed in the roaming decision. * * @QCA_ATTR_ROAM_CONTROL_HO_DELAY_FOR_RX: u16 value in milliseconds. * Optional parameter. This configuration delays hand-off (in msec) by the * specified duration to receive pending rx frames from current BSS. * * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_NO_REUSE_PARTIAL_SCAN_FREQ: Unsigned 8-bit * value. * During the roam scan, if there are no desired APs found in the partial * frequency list, an immediate full scan on all the supported frequencies * is initiated as a fallback. This flag controls the frequency list * creation for the full scan on the following lines. * 1 - Full scan to exclude the frequencies that were already scanned by * the previous partial scan. * 0 - Full scan to include all the supported frequencies irrespective of * the ones part of the earlier partial scan. * If this flag is not specified, a full scan shall include all the * supported frequencies irrespective of the ones part of an earlier * partial scan. * * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_6GHZ_ONLY_ON_PRIOR_DISCOVERY: Unsigned 8-bit * value. * During the roam scan, if there are no desired APs found in the partial * frequency list, an immediate full scan on all the supported frequencies * is initiated as a fallback. This full scan would add the 2.4/5/6 GHz * frequencies, including all PSC frequencies by default. This attribute * controls the inclusion of the 6 GHz PSC frequencies for the full scan * as following. * 1 - Full scan to include the supported 6 GHz PSC frequencies only on the * prior discovery of any 6 GHz frequency support in the environment. * This discovery can happen through a prior RNR, 11k neighbor * request, 11v BTM request, host scan, etc. * 0 - Default behavior. Full scan to include all the supported 6 GHz * PSC frequencies regardless of whether 6 GHz BSSs have been * discovered. * The default behavior if this flag is not specified is to include all * the supported 6 GHz PSC frequencies in the roam full scan. * * @QCA_ATTR_ROAM_CONTROL_CONNECTED_HIGH_RSSI_OFFSET: Unsigned 8-bit value. * This attribute signifies the RSSI offset that is added to low RSSI * threshold (QCA_ATTR_ROAM_CONTROL_CONNECTED_LOW_RSSI_THRESHOLD) to imply * high RSSI threshold. STA is expected to trigger roam if the current * connected AP's RSSI gets above this high RSSI threshold. STA's roam * attempt on high RSSI threshold aims to find candidates from other * better Wi-Fi bands. E.g., STA would initially connect to a 2.4 GHz BSSID * and would migrate to 5/6 GHz when it comes closer to the AP (high RSSI * for 2.4 GHz BSS). */ enum qca_vendor_attr_roam_control { QCA_ATTR_ROAM_CONTROL_ENABLE = 1, QCA_ATTR_ROAM_CONTROL_STATUS = 2, QCA_ATTR_ROAM_CONTROL_CLEAR_ALL = 3, QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME = 4, QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD = 5, QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD = 6, QCA_ATTR_ROAM_CONTROL_TRIGGERS = 7, QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA = 8, QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME = 9, QCA_ATTR_ROAM_CONTROL_CONNECTED_RSSI_THRESHOLD = 10, QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD = 11, QCA_ATTR_ROAM_CONTROL_USER_REASON = 12, QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS = 13, QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ = 14, QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ = 15, QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ = 16, QCA_ATTR_ROAM_CONTROL_BAND_MASK = 17, QCA_ATTR_ROAM_CONTROL_RX_LINKSPEED_THRESHOLD = 24, QCA_ATTR_ROAM_CONTROL_HO_DELAY_FOR_RX = 25, QCA_ATTR_ROAM_CONTROL_FULL_SCAN_NO_REUSE_PARTIAL_SCAN_FREQ = 26, QCA_ATTR_ROAM_CONTROL_FULL_SCAN_6GHZ_ONLY_ON_PRIOR_DISCOVERY = 27, QCA_ATTR_ROAM_CONTROL_CONNECTED_HIGH_RSSI_OFFSET = 31, /* keep last */ QCA_ATTR_ROAM_CONTROL_AFTER_LAST, QCA_ATTR_ROAM_CONTROL_MAX = QCA_ATTR_ROAM_CONTROL_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_roaming_config_params: Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD: Unsigned 32-bit value. * Represents the different roam sub commands referred by * enum qca_wlan_vendor_roaming_subcmd. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID: Unsigned 32-bit value. * Represents the Request ID for the specific set of commands. * This also helps to map specific set of commands to the respective * ID / client. e.g., helps to identify the user entity configuring the * Blacklist BSSID and accordingly clear the respective ones with the * matching ID. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS: Unsigned * 32-bit value.Represents the number of whitelist SSIDs configured. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST: Nested attribute * to carry the list of Whitelist SSIDs. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID: SSID (binary attribute, * 0..32 octets). Represents the white list SSID. Whitelist SSIDs * represent the list of SSIDs to which the firmware/driver can consider * to roam to. * * The following PARAM_A_BAND_XX attributes are applied to 5GHz BSSIDs when * comparing with a 2.4GHz BSSID. They are not applied when comparing two * 5GHz BSSIDs.The following attributes are set through the Roaming SUBCMD - * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_EXTSCAN_ROAM_PARAMS. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD: Signed 32-bit * value, RSSI threshold above which 5GHz RSSI is favored. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD: Signed 32-bit * value, RSSI threshold below which 5GHz RSSI is penalized. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR: Unsigned 32-bit * value, factor by which 5GHz RSSI is boosted. * boost=(RSSI_measured-5GHz_boost_threshold)*5GHz_boost_factor * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR: Unsigned 32-bit * value, factor by which 5GHz RSSI is penalized. * penalty=(5GHz_penalty_threshold-RSSI_measured)*5GHz_penalty_factor * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST: Unsigned 32-bit * value, maximum boost that can be applied to a 5GHz RSSI. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS: Unsigned 32-bit * value, boost applied to current BSSID to ensure the currently * associated BSSID is favored so as to prevent ping-pong situations. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER: Signed 32-bit * value, RSSI below which "Alert" roam is enabled. * "Alert" mode roaming - firmware is "urgently" hunting for another BSSID * because the RSSI is low, or because many successive beacons have been * lost or other bad link conditions. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE: Unsigned 32-bit * value. 1-Enable, 0-Disable. Represents "Lazy" mode, where * firmware is hunting for a better BSSID or white listed SSID even though * the RSSI of the link is good. The parameters enabling the roaming are * configured through the PARAM_A_BAND_XX attrbutes. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS: Nested attribute, * represents the BSSIDs preferred over others while evaluating them * for the roaming. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID: Unsigned * 32-bit value. Represents the number of preferred BSSIDs set. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID: 6-byte MAC * address representing the BSSID to be preferred. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER: Signed * 32-bit value, representing the modifier to be applied to the RSSI of * the BSSID for the purpose of comparing it with other roam candidate. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: Nested attribute, * represents the BSSIDs to get blacklisted for roaming. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: Unsigned * 32-bit value, represents the number of blacklisted BSSIDs. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: 6-byte MAC * address representing the Blacklisted BSSID. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT: Flag attribute, * indicates this BSSID blacklist as a hint to the driver. The driver can * select this BSSID in the worst case (when no other BSSIDs are better). * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL: Nested attribute to * set/get/clear the roam control config as * defined @enum qca_vendor_attr_roam_control. * * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX: Max */ enum qca_wlan_vendor_attr_roaming_config_params { QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL = 22, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_roaming_subcmd: Referred by * QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST: Sub command to * configure the white list SSIDs. These are configured through * the following attributes. * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS, * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST, * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_EXTSCAN_ROAM_PARAMS: Sub command to * configure the Roam params. These parameters are evaluated on the extscan * results. Refers the attributes PARAM_A_BAND_XX above to configure the * params. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM: Sets the Lazy roam. Uses * the attribute QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE * to enable/disable Lazy roam. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS: Sets the BSSID * preference. Contains the attribute * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS to set the BSSID * preference. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PARAMS: set bssid params * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID: Sets the Blacklist * BSSIDs. Refers QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS to * set the same. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET: Command to set the * roam control config to the driver with the attribute * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET: Command to obtain the * roam control config from driver with the attribute * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. * For the get, the attribute for the configuration to be queried shall * carry any of its acceptable value to the driver. In return, the driver * shall send the configured values within the same attribute to the user * space. * * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR: Command to clear the * roam control config in the driver with the attribute * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. * The driver shall continue with its default roaming behavior when data * corresponding to an attribute is cleared. */ enum qca_wlan_vendor_roaming_subcmd { QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST = 1, QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_EXTSCAN_ROAM_PARAMS = 2, QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM = 3, QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS = 4, QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PARAMS = 5, QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID = 6, QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET = 7, QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET = 8, QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR = 9, }; /** * enum qca_wlan_vendor_attr_get_wifi_info - wifi driver information * * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION: get host driver version * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION: ger firmware version * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX - get radio index * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST: after last * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX: subcmd max */ enum qca_wlan_vendor_attr_get_wifi_info { QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX = 3, /* KEEP LAST */ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_logger_results { QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, /* * Unsigned 32-bit value; must match the request Id supplied by * Wi-Fi HAL in the corresponding subcmd NL msg. */ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, /* * Unsigned 32-bit value; used to indicate the size of memory * dump to be allocated. */ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, }; /** * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. */ enum qca_wlan_vendor_channel_prop_flags { /* Bits 0, 1, 2, and 3 are reserved */ /* Turbo channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, /* CCK channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, /* OFDM channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, /* 2.4 GHz spectrum channel. */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, /* 5 GHz spectrum channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, /* Only passive scan allowed */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, /* Dynamic CCK-OFDM channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, /* GFSK channel (FHSS PHY) */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, /* Radar found on channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, /* 11a static turbo channel only */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, /* Half rate channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, /* Quarter rate channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, /* HT 20 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, /* HT 40 with extension channel above */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, /* HT 40 with extension channel below */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, /* HT 40 intolerant */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, /* VHT 20 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, /* VHT 40 with extension channel above */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, /* VHT 40 with extension channel below */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, /* VHT 80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, /* HT 40 intolerant mark bit for ACS use */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, /* Channel temporarily blocked due to noise */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, /* VHT 160 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, /* VHT 80+80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, /* HE 20 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, /* HE 40 with extension channel above */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, /* HE 40 with extension channel below */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, /* HE 40 intolerant */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1U << 31, }; /** * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. */ enum qca_wlan_vendor_channel_prop_flags_2 { /* HE 40 intolerant mark bit for ACS use */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, /* HE 80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, /* HE 160 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, /* HE 80+80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, }; /** * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for * each channel. This is used by * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. */ enum qca_wlan_vendor_channel_prop_flags_ext { /* Radar found on channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, /* DFS required on channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, /* DFS required on channel for 2nd band of 80+80 */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, /* If channel has been checked for DFS */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, /* Excluded in 802.11d */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, /* Channel Switch Announcement received on this channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, /* Ad-hoc is not allowed */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, /* Station only channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, /* DFS radar history for slave device (STA mode) */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, /* DFS CAC valid for slave device (STA mode) */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, }; /** * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite * information to start/stop the NUD statistics collection. */ enum qca_attr_nud_stats_set { QCA_ATTR_NUD_STATS_SET_INVALID = 0, /* * Flag to start/stop the NUD statistics collection. * Start - If included, Stop - If not included */ QCA_ATTR_NUD_STATS_SET_START = 1, /* IPv4 address of the default gateway (in network byte order) */ QCA_ATTR_NUD_STATS_GW_IPV4 = 2, /* * Represents the data packet type to be monitored. * Host driver tracks the stats corresponding to each data frame * represented by these flags. * These data packets are represented by * enum qca_wlan_vendor_nud_stats_set_data_pkt_info. */ QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, /* keep last */ QCA_ATTR_NUD_STATS_SET_LAST, QCA_ATTR_NUD_STATS_SET_MAX = QCA_ATTR_NUD_STATS_SET_LAST - 1, }; /** * enum qca_attr_connectivity_check_stats_set - attribute to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite * information to start / stop the NUD stats collection. * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_STATS_PKT_INFO_TYPE: set pkt info stats * Bitmap to Flag to Start / Stop the NUD stats collection * Start - If included , Stop - If not included * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DNS_DOMAIN_NAME: set gateway ipv4 address * IPv4 address of Default Gateway (in network byte order) * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite * information to start / stop the NUD stats collection. * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_SRC_PORT: set nud debug stats * Flag to Start / Stop the NUD stats collection * Start - If included , Stop - If not included * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_PORT: set gateway ipv4 address * IPv4 address of Default Gateway (in network byte order) * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite * information to start / stop the NUD stats collection. * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV4: set nud debug stats * Flag to Start / Stop the NUD stats collection * Start - If included , Stop - If not included * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV6: set gateway ipv4 address * IPv4 address of Default Gateway (in network byte order) */ enum qca_attr_connectivity_check_stats_set { QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_INVALID = 0, QCA_ATTR_CONNECTIVITY_CHECK_STATS_STATS_PKT_INFO_TYPE = 1, QCA_ATTR_CONNECTIVITY_CHECK_STATS_DNS_DOMAIN_NAME = 2, QCA_ATTR_CONNECTIVITY_CHECK_STATS_SRC_PORT = 3, QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_PORT = 4, QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV4 = 5, QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV6 = 6, /* keep last */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_LAST, QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_MAX = QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_LAST - 1, }; /** * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various * data types for which the stats have to get collected. */ enum qca_wlan_vendor_connectivity_check_pkt_flags { QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ARP = 1 << 0, QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_DNS = 1 << 1, QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_HANDSHAKE = 1 << 2, QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ICMPV4 = 1 << 3, QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ICMPV6 = 1 << 4, /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get * to represent the stats of respective data type. */ QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_SYN = 1 << 5, QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_SYN_ACK = 1 << 6, QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_ACK = 1 << 7, }; enum qca_attr_connectivity_check_stats { QCA_ATTR_CONNECTIVITY_CHECK_STATS_INVALID = 0, /* Data packet type for which the stats are collected. * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_TYPE = 1, /* ID corresponding to the DNS frame for which the respective DNS stats * are monitored (u32). */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DNS_DOMAIN_NAME = 2, /* source / destination port on which the respective proto stats are * collected (u32). */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_SRC_PORT = 3, QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_PORT = 4, /* IPv4/IPv6 address for which the destined data packets are * monitored. (in network byte order) */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_IPV4 = 5, QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_IPV6 = 6, /* Data packet Request count received from netdev */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, /* Data packet Request count sent to lower MAC from upper MAC */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, /* Data packet Request count received by lower MAC from upper MAC */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, /* Data packet Request count successfully transmitted by the device */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, /* Data packet Response count received by lower MAC */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, /* Data packet Response count received by upper MAC */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, /* Data packet Response count delivered to netdev */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, /* Data Packet Response count that are dropped out of order */ QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, /* keep last */ QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_LAST, QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_MAX = QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_LAST - 1, }; /** * qca_attr_nud_stats_get: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite * NUD statistics collected when queried. */ enum qca_attr_nud_stats_get { QCA_ATTR_NUD_STATS_GET_INVALID = 0, /* ARP Request count from netdev */ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, /* ARP Request count sent to lower MAC from upper MAC */ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, /* ARP Request count received by lower MAC from upper MAC */ QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, /* ARP Request count successfully transmitted by the device */ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, /* ARP Response count received by lower MAC */ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, /* ARP Response count received by upper MAC */ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, /* ARP Response count delivered to netdev */ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, /* ARP Response count delivered to netdev */ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, /* * Flag indicating if the station's link to the AP is active. * Active Link - If included, Inactive link - If not included */ QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, /* * Flag indicating if there is any duplicate address detected (DAD). * Yes - If detected, No - If not detected. */ QCA_ATTR_NUD_STATS_IS_DAD = 10, /* * List of Data types for which the stats are requested. * This list does not carry ARP stats as they are done by the * above attributes. Represented by enum qca_attr_nud_data_stats. */ QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, /* keep last */ QCA_ATTR_NUD_STATS_GET_LAST, QCA_ATTR_NUD_STATS_GET_MAX = QCA_ATTR_NUD_STATS_GET_LAST - 1, }; enum qca_wlan_btm_candidate_status { QCA_STATUS_ACCEPT = 0, QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, QCA_STATUS_REJECT_LOW_RSSI = 4, QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, QCA_STATUS_REJECT_UNKNOWN = 6, }; enum qca_wlan_vendor_attr_btm_candidate_info { QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, /* 6-byte MAC address representing the BSSID of transition candidate */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, /* * Unsigned 32-bit value from enum qca_wlan_btm_candidate_status * returned by the driver. It says whether the BSSID provided in * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by * the driver, if not it specifies the reason for rejection. * Note that the user-space can overwrite the transition reject reason * codes provided by driver based on more information. */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, }; enum qca_attr_trace_level { QCA_ATTR_TRACE_LEVEL_INVALID = 0, /* * Nested array of the following attributes: * QCA_ATTR_TRACE_LEVEL_MODULE, * QCA_ATTR_TRACE_LEVEL_MASK. */ QCA_ATTR_TRACE_LEVEL_PARAM = 1, /* * Specific QCA host driver module. Please refer to the QCA host * driver implementation to get the specific module ID. */ QCA_ATTR_TRACE_LEVEL_MODULE = 2, /* Different trace level masks represented in the QCA host driver. */ QCA_ATTR_TRACE_LEVEL_MASK = 3, /* keep last */ QCA_ATTR_TRACE_LEVEL_AFTER_LAST, QCA_ATTR_TRACE_LEVEL_MAX = QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_logger_features - value for logger * supported features * @QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID - Invalid * @QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED - Indicate the supported features * @QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - To keep track of the last enum * @QCA_WLAN_VENDOR_ATTR_LOGGER_MAX - max value possible for this type * * enum values are used for NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET sub command. */ enum qca_wlan_vendor_attr_get_logger_features { QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_link_properties - link properties * * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID: Invalid initial value * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_NSS: Unsigned 8-bit value to * specify the number of spatial streams negotiated * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_RATE_FLAGS: Unsigned 8-bit value * to specify negotiated rate flags i.e. ht, vht and channel width * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_FREQ: Unsigned 32bit value to * specify the operating frequency * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC Address of the peer * (STA / AP ) for the connected link. * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a * &struct nl80211_sta_flag_update for the respective connected link. MAC * address of the peer represented by * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST: after last * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAX: max value */ enum qca_wlan_vendor_attr_link_properties { QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_NSS = 1, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_RATE_FLAGS = 2, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_FREQ = 3, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, /* KEEP LAST */ QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAX = QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_nd_offload - vendor NS offload support * * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID - Invalid * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG - Flag to set NS offload * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - To keep track of the last enum * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX - max value possible for this type * * enum values are used for NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD sub command. */ enum qca_wlan_vendor_attr_nd_offload { QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, /* Keep last */ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_features - Vendor device/driver feature flags * * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key * management offload, a mechanism where the station's firmware * does the exchange with the AP to establish the temporal keys * after roaming, rather than having the user space wpa_supplicant do it. * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic * band selection based on channel selection results. * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports * simultaneous off-channel operations. * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P * Listen offload; a mechanism where the station's firmware takes care of * responding to incoming Probe Request frames received from other P2P * Devices whilst in Listen state, rather than having the user space * wpa_supplicant do it. Information from received P2P requests are * forwarded from firmware to host whenever the host processor wakes up. * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA * specific features. * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific * features. * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON * specific features only. If a Device sets this bit but not the * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that * this Device may not support all OCE AP functionalities but can support * only OCE STA-CFON functionalities. * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self * managed regulatory. * @QCA_WLAN_VENDOR_FEATURE_TWT: Device supports TWT (Target Wake Time). * @QCA_WLAN_VENDOR_FEATURE_11AX: Device supports 802.11ax (HE) * @QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT: Device supports 6 GHz band operation * @QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG: Device is capable of receiving * and applying thermal configuration through * %QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL and * %QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW attributes from * userspace. * @QCA_WLAN_VENDOR_FEATURE_ADAPTIVE_11R: Device supports Adaptive 11r. * With Adaptive 11r feature, access points advertise the vendor * specific IEs and MDE but do not include FT AKM in the RSNE. * The Adaptive 11r supported stations are expected to identify * such vendor specific IEs and connect to the AP in FT mode though * the profile is configured in non-FT mode. * The driver-based SME cases also need to have this support for * Adaptive 11r to handle the connection and roaming scenarios. * This flag indicates the support for the same to the user space. * @QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS: Device supports * concurrent network sessions on different Wi-Fi Bands. This feature * capability is attributed to the hardware's capability to support * the same (e.g., DBS). * @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT: Flag indicating whether the * responses for the respective TWT operations are asynchronous (separate) * event message) from the driver. If not specified, the responses are * synchronous (in vendor command reply) to the request. Each TWT * operation is specifically mentioned (against its respective) * documentation) to support either of these or both modes. * @QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI: Flag indicates * that the driver requires add/del virtual interface path using the * generic nl80211 commands for NDP interface create/delete and to * register/unregister the netdev instead of creating/deleting the NDP * interface using the vendor commands * QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE and * QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE. With the latest kernel * (5.12 version onward), interface creation/deletion is not allowed using * vendor commands as it leads to a deadlock while acquiring the RTNL_LOCK * during the register/unregister of netdev. Create and delete NDP * interface using NL80211_CMD_NEW_INTERFACE and NL80211_CMD_DEL_INTERFACE * commands respectively if the driver advertises this capability set. * @QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_STA: Flag indicates that the device in * station mode supports secure LTF. If NL80211_EXT_FEATURE_SECURE_LTF is * set, then QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_STA will be ignored. * @QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_AP: Flag indicates that the device in AP * mode supports secure LTF. If NL80211_EXT_FEATURE_SECURE_LTF is set, then * QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_AP will be ignored. * @QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_STA: Flag indicates that the device in * station mode supports secure RTT measurement exchange. If * NL80211_EXT_FEATURE_SECURE_RTT is set, * QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_STA will be ignored. * @QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_AP: Flag indicates that the device in AP * mode supports secure RTT measurement exchange. If * NL80211_EXT_FEATURE_SECURE_RTT is set, * QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_AP will be ignored. * @QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_STA: Flag indicates that * the device in station mode supports protection of range negotiation and * measurement management frames. If * NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE is set, then * QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_STA will be ignored. * @QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_AP: Flag indicates that * the device in AP mode supports protection of range negotiation and * measurement management frames. If * NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE is set, then * QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_AP will be ignored. * @QCA_WLAN_VENDOR_FEATURE_AP_ALLOWED_FREQ_LIST: Flag indicates that the device * in AP mode supports configuring allowed frequency list for AP operation * with %QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST. * @QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN: Flag indicates * that the device supports enhanced audio experience over WLAN feature. * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits */ enum qca_wlan_vendor_features { QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, QCA_WLAN_VENDOR_FEATURE_TWT = 8, QCA_WLAN_VENDOR_FEATURE_11AX = 9, QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT = 10, QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG = 11, QCA_WLAN_VENDOR_FEATURE_ADAPTIVE_11R = 12, QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS = 13, QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT = 14, QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI = 15, QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_STA = 16, QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_AP = 17, QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_STA = 18, QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_AP = 19, QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_STA = 20, QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_AP = 21, QCA_WLAN_VENDOR_FEATURE_AP_ALLOWED_FREQ_LIST = 22, QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN = 23, NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */ }; /** * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for SAP * conditional channel switch * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID: Invalid initial * value * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST: Priority based * frequency list (an array of u32 values in host byte order) * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS: Status of the * conditional switch (u32)- 0: Success, Non-zero: Failure * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST: After last * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX: Subcommand max */ enum qca_wlan_vendor_attr_sap_conditional_chan_switch { QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, /* Keep Last */ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, }; /** * enum wifi_logger_supported_features - values for supported logger features * @WIFI_LOGGER_MEMORY_DUMP_SUPPORTED: Memory dump of FW * @WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_SUPPORTED: Per packet statistics * @WIFI_LOGGER_CONNECT_EVENT_SUPPORTED: Logging of Connectivity events * @WIFI_LOGGER_POWER_EVENT_SUPPORTED: Power of driver * @WIFI_LOGGER_WAKE_LOCK_SUPPORTE: Wakelock of driver * @WIFI_LOGGER_WATCHDOG_TIMER_SUPPORTED: monitor FW health * @WIFI_LOGGER_DRIVER_DUMP_SUPPORTED: support driver dump * @WIFI_LOGGER_PACKET_FATE_SUPPORTED: tracks connection packets fate */ enum wifi_logger_supported_features { WIFI_LOGGER_MEMORY_DUMP_SUPPORTED = (1 << (0)), WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_SUPPORTED = (1 << (1)), WIFI_LOGGER_CONNECT_EVENT_SUPPORTED = (1 << (2)), WIFI_LOGGER_POWER_EVENT_SUPPORTED = (1 << (3)), WIFI_LOGGER_WAKE_LOCK_SUPPORTED = (1 << (4)), WIFI_LOGGER_VERBOSE_SUPPORTED = (1 << (5)), WIFI_LOGGER_WATCHDOG_TIMER_SUPPORTED = (1 << (6)), WIFI_LOGGER_DRIVER_DUMP_SUPPORTED = (1 << (7)), WIFI_LOGGER_PACKET_FATE_SUPPORTED = (1 << (8)) }; /** * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get * capabilities features */ enum qca_wlan_tdls_caps_features_supported { WIFI_TDLS_SUPPORT = (1 << (0)), WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)), WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2)), /* Indicates if the TDLS session can be formed with the peer using * higher bandwidth than the bandwidth of the AP path. */ WIFI_TDLS_WIDER_BW_SUPPORT = (1 << (3)), }; /** * enum qca_wlan_vendor_attr_acs_offload - Defines attributes to be used with * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS. * * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL: Required (u8). * Used with event to notify the primary channel number selected in ACS * operation. * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL is deprecated; use * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY instead. * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL * is still used if either of the driver or user space application doesn't * support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL: Required (u8). * Used with event to notify the secondary channel number selected in ACS * operation. * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is deprecated; use * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY instead. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is still used if either of * the driver or user space application doesn't support 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE: Required (u8). * (a) Used with command to configure hw_mode from * enum qca_wlan_vendor_acs_hw_mode for ACS operation. * (b) Also used with event to notify the hw_mode of selected primary channel * in ACS operation. * * @QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED: Flag attribute. * Used with command to configure ACS operation for HT mode. * Disable (flag attribute not present) - HT disabled and * Enable (flag attribute present) - HT enabled. * * @QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED: Flag attribute. * Used with command to configure ACS operation for HT40 mode. * Disable (flag attribute not present) - HT40 disabled and * Enable (flag attribute present) - HT40 enabled. * * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED: Flag attribute. * Used with command to configure ACS operation for VHT mode. * Disable (flag attribute not present) - VHT disabled and * Enable (flag attribute present) - VHT enabled. * * @QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH: Optional (u16) with command and * mandatory with event. * If specified in command path, ACS operation is configured with the given * channel width (in MHz). * In event path, specifies the channel width of the primary channel selected. * * @QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST: Required and type is NLA_UNSPEC. * Used with command to configure channel list using an array of * channel numbers (u8). * Note: If both the driver and user-space application supports the 6 GHz band, * the driver mandates use of QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST whereas * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST is optional. * * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL: Required (u8). * Used with event to notify the VHT segment 0 center channel number selected in * ACS operation. * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is deprecated; use * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY instead. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is still used if either of * the driver or user space application doesn't support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL: Required (u8). * Used with event to notify the VHT segment 1 center channel number selected in * ACS operation. * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is deprecated; use * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY instead. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is still used if either of * the driver or user space application doesn't support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST: Required and type is NLA_UNSPEC. * Used with command to configure the channel list using an array of channel * center frequencies in MHz (u32). * Note: If both the driver and user-space application supports the 6 GHz band, * the driver first parses the frequency list and if it fails to get a frequency * list, parses the channel list specified using * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST (considers only 2 GHz and 5 GHz channels in * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST). * * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY: Required (u32). * Used with event to notify the primary channel center frequency (MHz) selected * in ACS operation. * Note: If the driver supports the 6 GHz band, the event sent from the driver * includes this attribute along with QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL. * * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY: Required (u32). * Used with event to notify the secondary channel center frequency (MHz) * selected in ACS operation. * Note: If the driver supports the 6 GHz band, the event sent from the driver * includes this attribute along with * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL. * * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY: Required (u32). * Used with event to notify the VHT segment 0 center channel frequency (MHz) * selected in ACS operation. * Note: If the driver supports the 6 GHz band, the event sent from the driver * includes this attribute along with * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL. * * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY: Required (u32). * Used with event to notify the VHT segment 1 center channel frequency (MHz) * selected in ACS operation. * Note: If the driver supports the 6 GHz band, the event sent from the driver * includes this attribute along with * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL. * * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED: Flag attribute. * Used with command to notify the driver of EDMG request for ACS * operation. * * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL: Optional (u8). * Used with event to notify the EDMG channel number selected in ACS * operation. * EDMG primary channel is indicated by QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL * * @QCA_WLAN_VENDOR_ATTR_ACS_PUNCTURE_BITMAP: Optional (u16). * Used with event to notify the puncture pattern selected in ACS operation. * Encoding for this attribute will follow the convention used in the Disabled * Subchannel Bitmap field of the EHT Operation IE. * * @QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED: Flag attribute. * Used with command to configure ACS operation for EHT mode. * Disable (flag attribute not present) - EHT disabled and * Enable (flag attribute present) - EHT enabled. * * @QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME: Optional (u32). * Used with command to configure how older scan can be considered for ACS * scoring. In case scan was performed on partial set of channels configured * with this command, within last QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME * (in ms), then scan only remaining channels. */ enum qca_wlan_vendor_attr_acs_offload { QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL = 1, QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL = 2, QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE = 3, QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED = 4, QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED = 5, QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED = 6, QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH = 7, QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST = 8, QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL = 9, QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL = 10, QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST = 11, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY = 12, QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY = 13, QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY = 14, QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY = 15, QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED = 16, QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL = 17, QCA_WLAN_VENDOR_ATTR_ACS_PUNCTURE_BITMAP = 18, QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED = 19, QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME = 20, /* keep last */ QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ACS_MAX = QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_acs_hw_mode - Defines HW mode to be used with the * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS. * * @QCA_ACS_MODE_IEEE80211B: 802.11b mode * @QCA_ACS_MODE_IEEE80211G: 802.11g mode * @QCA_ACS_MODE_IEEE80211A: 802.11a mode * @QCA_ACS_MODE_IEEE80211AD: 802.11ad mode * @QCA_ACS_MODE_IEEE80211ANY: all modes * @QCA_ACS_MODE_IEEE80211AX: 802.11ax mode */ enum qca_wlan_vendor_acs_hw_mode { QCA_ACS_MODE_IEEE80211B, QCA_ACS_MODE_IEEE80211G, QCA_ACS_MODE_IEEE80211A, QCA_ACS_MODE_IEEE80211AD, QCA_ACS_MODE_IEEE80211ANY, QCA_ACS_MODE_IEEE80211AX, }; /** * enum qca_access_policy - access control policy * * Access control policy is applied on the configured IE * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. * * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi Connections which match *» with the specific configuration (IE) set, i.e. allow all the *» connections which do not match the configuration. * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi Connections which match *» with the specific configuration (IE) set, i.e. deny all the *» connections which do not match the configuration. */ enum qca_access_policy { QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, }; /** * enum qca_ignore_assoc_disallowed - Ignore assoc disallowed values * * The valid values for the ignore assoc disallowed * * @QCA_IGNORE_ASSOC_DISALLOWED_DISABLE: Disable ignore assoc disallowed * @QCA_IGNORE_ASSOC_DISALLOWED_ENABLE: Enable ignore assoc disallowed * */ enum qca_ignore_assoc_disallowed { QCA_IGNORE_ASSOC_DISALLOWED_DISABLE, QCA_IGNORE_ASSOC_DISALLOWED_ENABLE }; /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. */ #define QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES\ QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES #define QCA_WLAN_VENDOR_ATTR_BEACON_REPORT_FAIL\ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL #define QCA_WLAN_VENDOR_ATTR_ROAM_REASON\ QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON enum qca_wlan_vendor_attr_config { QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, /* * Unsigned 32-bit value to set the DTIM period. * Whether the wifi chipset wakes at every dtim beacon or a multiple of * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 * DTIM beacons. */ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, /* * Unsigned 32-bit value to set the wifi_iface stats averaging factor * used to calculate statistics like average the TSF offset or average * number of frame leaked. * For instance, upon Beacon frame reception: * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 * For instance, when evaluating leaky APs: * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 */ QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, /* * Unsigned 32-bit value to configure guard time, i.e., when * implementing IEEE power management based on frame control PM bit, how * long the driver waits before shutting down the radio and after * receiving an ACK frame for a Data frame with PM bit set. */ QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, /* Unsigned 32-bit value to change the FTM capability dynamically */ QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, /* Unsigned 16-bit value to configure maximum TX rate dynamically */ QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, /* * Unsigned 32-bit value to configure the number of continuous * Beacon Miss which shall be used by the firmware to penalize * the RSSI. */ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, /* * Unsigned 8-bit value to configure the channel avoidance indication * behavior. Firmware to send only one indication and ignore duplicate * indications when set to avoid multiple Apps wakeups. */ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, /* * 8-bit unsigned value to configure the maximum TX MPDU for * aggregation. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, /* * 8-bit unsigned value to configure the maximum RX MPDU for * aggregation. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, /* * 8-bit unsigned value to configure the Non aggregate/11g sw * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, /* * 8-bit unsigned value to configure the aggregate sw * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, /* * 8-bit unsigned value to configure the MGMT frame * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, /* * 8-bit unsigned value to configure the CTRL frame * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, /* * 8-bit unsigned value to configure the propagation delay for * 2G/5G band (0~63, units in us) */ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, /* * Unsigned 32-bit value to configure the number of unicast TX fail * packet count. The peer is disconnected once this threshold is * reached. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, /* * Attribute used to set scan default IEs to the driver. * * These IEs can be used by scan operations that will be initiated by * the driver/firmware. * * For further scan requests coming to the driver, these IEs should be * merged with the IEs received along with scan request coming to the * driver. If a particular IE is present in the scan default IEs but not * present in the scan request, then that IE should be added to the IEs * sent in the Probe Request frames for that scan request. */ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, /* Unsigned 32-bit attribute for generic commands */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, /* Unsigned 32-bit value attribute for generic commands */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, /* Unsigned 32-bit data attribute for generic command response */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, /* * Unsigned 32-bit length attribute for * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, /* * Unsigned 32-bit flags attribute for * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, /* * Unsigned 32-bit, defining the access policy. * See enum qca_access_policy. Used with * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, /* * Sets the list of full set of IEs for which a specific access policy * has to be applied. Used along with * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. * Zero length payload can be used to clear this access constraint. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, /* * Unsigned 32-bit, specifies the interface index (netdev) for which the * corresponding configurations are applied. If the interface index is * not specified, the configurations are attributed to the respective * wiphy. */ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, /* * 8-bit unsigned value to trigger QPower: * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, /* * 8-bit unsigned value to configure the driver and below layers to * ignore the assoc disallowed set by APs while connecting * 1-Ignore, 0-Don't ignore */ QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, /* * 32-bit unsigned value to trigger antenna diversity features: * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, /* 32-bit unsigned value to configure specific chain antenna */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, /* * 32-bit unsigned value to trigger cycle selftest * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, /* * 32-bit unsigned to configure the cycle time of selftest * the unit is micro-second */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, /* 32-bit unsigned value to set reorder timeout for AC_VO */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, /* 32-bit unsigned value to set reorder timeout for AC_VI */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, /* 32-bit unsigned value to set reorder timeout for AC_BE */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, /* 32-bit unsigned value to set reorder timeout for AC_BK */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, /* 6-byte MAC address to point out the specific peer */ QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC = 35, /* Backward compatibility with the original name */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC, /* 32-bit unsigned value to set window size for specific peer */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, /* * 32-bit unsigned value to configure 5 or 10 MHz channel width for * station device while in disconnect state. The attribute use the * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or * 10 MHz channel width, the station will not connect to a BSS using 20 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to * clear this constraint. */ QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, /* * 32-bit unsigned value to configure the propagation absolute delay * for 2G/5G band (units in us) */ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, /* 32-bit unsigned value to set probe period */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, /* 32-bit unsigned value to set stay period */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, /* 32-bit unsigned value to set snr diff */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, /* 32-bit unsigned value to set probe dwell time */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, /* 32-bit unsigned value to set mgmt snr weight */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, /* 32-bit unsigned value to set data snr weight */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, /* 32-bit unsigned value to set ack snr weight */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, /* * 32-bit unsigned value to configure the listen interval. * This is in units of beacon intervals. This configuration alters * the negotiated listen interval with the AP during the connection. * It is highly recommended to configure a value less than or equal to * the one negotiated during the association. Configuring any greater * value can have adverse effects (frame loss, AP disassociating STA, * etc.). */ QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, /* * 8 bit unsigned value that is set on an AP/GO virtual interface to * disable operations that would cause the AP/GO to leave its operating * channel. * * This will restrict the scans to the AP/GO operating channel and the * channels of the other band, if DBS is supported.A STA/CLI interface * brought up after this setting is enabled, will be restricted to * connecting to devices only on the AP/GO interface's operating channel * or on the other band in DBS case. P2P supported channel list is * modified, to only include AP interface's operating-channel and the * channels of the other band if DBS is supported. * * These restrictions are only applicable as long as the AP/GO interface * is alive. If the AP/GO interface is brought down then this * setting/restriction is forgotten. * * If this variable is set on an AP/GO interface while a multi-channel * concurrent session is active, it has no effect on the operation of * the current interfaces, other than restricting the scan to the AP/GO * operating channel and the other band channels if DBS is supported. * However, if the STA is brought down and restarted then the new STA * connection will either be formed on the AP/GO channel or on the * other band in a DBS case. This is because of the scan being * restricted on these channels as mentioned above. * * 1-Disable offchannel operations, 0-Enable offchannel operations. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, /* * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) * on an interface. * 1 - Enable , 0 - Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, /* * 8 bit unsigned value to globally enable/disable scan * 1 - Enable, 0 - Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, /* 8-bit unsigned value to set the total beacon miss count */ QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, /* * Unsigned 32-bit value to configure the number of continuous * Beacon Miss which shall be used by the firmware to penalize * the RSSI for BTC. */ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, /* * 8-bit unsigned value to configure the driver and below layers to * enable/disable all fils features. * 0-enable, 1-disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, /* 16-bit unsigned value to configure the level of WLAN latency * module. See enum qca_wlan_vendor_attr_config_latency_level. */ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, /* * 8-bit unsigned value indicating the driver to use the RSNE as-is from * the connect interface. Exclusively used for the scenarios where the * device is used as a test bed device with special functionality and * not recommended for production. This helps driver to not validate the * RSNE passed from user space and thus allow arbitrary IE data to be * used for testing purposes. * 1-enable, 0-disable. * Applications set/reset this configuration. If not reset, this * parameter remains in use until the driver is unloaded. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, /* * 8-bit unsigned value to trigger green Tx power saving. * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, /* * Attribute to configure disconnect IEs to the driver. * This carries an array of unsigned 8-bit characters. * * If this is configured, driver shall fill the IEs in disassoc/deauth * frame. * These IEs are expected to be considered only for the next * immediate disconnection (disassoc/deauth frame) originated by * the DUT, irrespective of the entity (user space/driver/firmware) * triggering the disconnection. * The host drivers are not expected to use the IEs set through * this interface for further disconnections after the first immediate * disconnection initiated post the configuration. * If the IEs are also updated through cfg80211 interface (after the * enhancement to cfg80211_disconnect), host driver is expected to * take the union of IEs from both of these interfaces and send in * further disassoc/deauth frames. */ QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES = 58, /* 8-bit unsigned value for ELNA bypass. * 0 - Disable eLNA bypass. * 1 - Enable eLNA bypass. * 2 - Reset eLNA bypass configuration, the driver should * revert to the default configuration of eLNA bypass. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS = 59, /* 8-bit unsigned value. This attribute enables/disables the host driver * to send the Beacon Report response with failure reason for the * scenarios where STA cannot honor the Beacon report request from AP. * 1-Enable, 0-Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL = 60, /* 8-bit unsigned value. This attribute enables/disables the host driver * to send roam reason information in the reassociation request to the * AP. 1-Enable, 0-Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON = 61, /* 32-bit unsigned value to configure different PHY modes to the * driver/firmware. The possible values are defined in * enum qca_wlan_vendor_phy_mode. The configuration will be reset to * default value, i.e., QCA_WLAN_VENDOR_PHY_MODE_AUTO upon restarting * the driver. */ QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE = 62, /* 8-bit unsigned value to configure the maximum supported channel width * for STA mode. If this value is configured when STA is in connected * state, it should not exceed the negotiated channel width. If it is * configured when STA is in disconnected state, the configured value * will take effect for the next immediate connection. * This configuration can be sent inside * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINKS to specify the maximum * supported channel width per-MLO link. * * This uses values defined in enum nl80211_chan_width. */ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH = 63, /* 8-bit unsigned value to enable/disable dynamic bandwidth adjustment. * This attribute is only applicable for STA mode. When dynamic * bandwidth adjustment is disabled, STA will use static channel width * the value of which is negotiated during connection. * 1-enable (default), 0-disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_BW = 64, /* 8-bit unsigned value to configure the maximum number of subframes of * TX MSDU for aggregation. Possible values are 0-31. When set to 0, * it is decided by hardware. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MSDU_AGGREGATION = 65, /* 8-bit unsigned value to configure the maximum number of subframes of * RX MSDU for aggregation. Possible values are 0-31. When set to 0, * it is decided by hardware. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MSDU_AGGREGATION = 66, /* 8-bit unsigned value. This attribute is used to dynamically * enable/disable the LDPC capability of the device. When configured in * the disconnected state, the updated configuration will be considered * for the immediately following connection attempt. If this * configuration is modified while the device is in the connected state, * the LDPC TX will be updated with this configuration immediately, * while the LDPC RX configuration update will take place starting from * the subsequent association attempt. * 1-Enable, 0-Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_LDPC = 67, /* 8-bit unsigned value. This attribute is used to dynamically * enable/disable the TX STBC capability of the device. When configured * in the disconnected state, the updated configuration will be * considered for the immediately following connection attempt. If the * connection is formed with TX STBC enabled and if this configuration * is disabled during that association, the TX will be impacted * immediately. Further connection attempts will disable TX STBC. * However, enabling the TX STBC for a connected session with disabled * capability is not allowed and will fail. * 1-Enable, 0-Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_STBC = 68, /* 8-bit unsigned value. This attribute is used to dynamically * enable/disable the RX STBC capability of the device. When configured * in the disconnected state, the updated configuration will be * considered for the immediately following connection attempt. If the * configuration is modified in the connected state, there will be no * impact for the current association, but further connection attempts * will use the updated configuration. * 1-Enable, 0-Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_STBC = 69, /* 8-bit unsigned value. This attribute is used to dynamically configure * the number of spatial streams. When configured in the disconnected * state, the updated configuration will be considered for the * immediately following connection attempt. If the NSS is updated after * the connection, the updated NSS value is notified to the peer using * the Operating Mode Notification/Spatial Multiplexing Power Save * frame. The updated NSS value after the connection shall not be * greater than the one negotiated during the connection. Any such * higher value configuration shall be returned with a failure. * Only symmetric NSS configuration (such as 2X2 or 1X1) can be done * using this attribute. QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS and * QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attributes shall be used to * configure the asymmetric NSS configuration (such as 1X2). */ QCA_WLAN_VENDOR_ATTR_CONFIG_NSS = 70, /* 8-bit unsigned value to configure Optimized Power Management mode: * Modes are defined by enum qca_wlan_vendor_opm_mode. * * This attribute shall be configured along with * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO and * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE_INTERVAL attributes * when its value is set to %QCA_WLAN_VENDOR_OPM_MODE_USER_DEFINED. */ QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT = 71, /* 8-bit unsigned value. This attribute takes the QOS/access category * value represented by the enum qca_wlan_ac_type and expects the driver * to upgrade the UDP frames to this QOS. The value of QCA_WLAN_AC_ALL * is invalid for this attribute. This will override the DSCP value * configured in the frame with the intention to only upgrade the QOS. * That said, it is not intended to downgrade the QOS for the frames. * Set the value to 0 ( corresponding to BE ) if the QOS upgrade needs * to disable. * * If only UDP frames of BE or BK access category needs to be upgraded * without changing the access category of VO or VI UDP frames, refer to * attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE_FOR_BE_BK. * * This attribute is not recommended to be used as it blindly forces all * UDP packets to a higher access category which could impact the * traffic pattern of all apps using UDP and can cause unknown behavior. */ QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE = 72, /* 8-bit unsigned value. This attribute is used to dynamically configure * the number of chains to be used for transmitting data. This * configuration is allowed only when in connected state and will be * effective until disconnected. The driver rejects this configuration * if the number of spatial streams being used in the current connection * cannot be supported by this configuration. */ QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_TX_CHAINS = 73, /* 8-bit unsigned value. This attribute is used to dynamically configure * the number of chains to be used for receiving data. This * configuration is allowed only when in connected state and will be * effective until disconnected. The driver rejects this configuration * if the number of spatial streams being used in the current connection * cannot be supported by this configuration. */ QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_RX_CHAINS = 74, /* 8-bit unsigned value to configure ANI setting type. * See &enum qca_wlan_ani_setting for possible values. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_SETTING = 75, /* 32-bit signed value to configure ANI level. This is used when * ANI settings type is &QCA_WLAN_ANI_SETTING_FIXED. * The set and get of ANI level with &QCA_WLAN_ANI_SETTING_AUTO * is invalid, the driver will return a failure. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_LEVEL = 76, /* 8-bit unsigned value. This attribute is used to dynamically configure * the number of spatial streams used for transmitting the data. When * configured in the disconnected state, the configured value will * be considered for the following connection attempt. * If the NSS is updated after the connection, the updated NSS value * is notified to the peer using the Operating Mode Notification/Spatial * Multiplexing Power Save frame. * The TX NSS value configured after the connection shall not be greater * than the value negotiated during the connection. Any such higher * value configuration shall be treated as invalid configuration by * the driver. This attribute shall be configured along with * QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attribute to define the symmetric * configuration (such as 2X2 or 1X1) or the asymmetric * configuration (such as 1X2). * If QCA_WLAN_VENDOR_ATTR_CONFIG_NSS attribute is also provided along * with this QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS attribute the driver * will update the TX NSS based on QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS = 77, /* 8-bit unsigned value. This attribute is used to dynamically configure * the number of spatial streams used for receiving the data. When * configured in the disconnected state, the configured value will * be considered for the following connection attempt. * If the NSS is updated after the connection, the updated NSS value * is notified to the peer using the Operating Mode Notification/Spatial * Multiplexing Power Save frame. * The RX NSS value configured after the connection shall not be greater * than the value negotiated during the connection. Any such higher * value configuration shall be treated as invalid configuration by * the driver. This attribute shall be configured along with * QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS attribute to define the symmetric * configuration (such as 2X2 or 1X1) or the asymmetric * configuration (such as 1X2). * If QCA_WLAN_VENDOR_ATTR_CONFIG_NSS attribute is also provided along * with this QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attribute the driver * will update the RX NSS based on QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS = 78, /* * 8-bit unsigned value. This attribute, when set, indicates whether the * specified interface is the primary STA interface when there are more * than one STA interfaces concurrently active. * * This configuration helps the firmware/hardware to support certain * features (e.g., roaming) on this primary interface, if the same * cannot be supported on the concurrent STA interfaces simultaneously. * * This configuration is only applicable for a single STA interface on * a device and gives the priority for it only over other concurrent STA * interfaces. * * If the device is a multi wiphy/soc, this configuration applies to a * single STA interface across the wiphys. * * 1-Enable (is the primary STA), 0-Disable (is not the primary STA) */ QCA_WLAN_VENDOR_ATTR_CONFIG_CONCURRENT_STA_PRIMARY = 79, /* * 8-bit unsigned value. This attribute can be used to configure the * driver to enable/disable FT-over-DS feature. Possible values for * this attribute are 1-Enable and 0-Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS = 80, /* * 8-bit unsigned value. This attribute can be used to configure the * firmware to enable/disable ARP/NS offload feature. Possible values * for this attribute are 0-Disable and 1-Enable. * * This attribute is only applicable for STA/P2P-Client interface, * and is optional, default behavior is APR/NS offload Enable. * * This attribute can be set in disconncted and connected state, and * will restore to default behavior if interface is closed. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ARP_NS_OFFLOAD = 81, /* * 8-bit unsigned value. This attribute can be used to configure the * Dedicated Bluetooth Antenna Mode (DBAM) feature. Possible values * for this attribute are defined in the enum qca_dbam_config. */ QCA_WLAN_VENDOR_ATTR_CONFIG_DBAM = 83, /* 8-bit unsigned value. This attribute takes the QoS/access category * value represented by the enum qca_wlan_ac_type and expects the driver * to upgrade the UDP frames of BE or BK access category to this access * category. This attribute will not modify UDP frames of VO or VI * access category. The value of QCA_WLAN_AC_ALL is invalid for this * attribute. * * This will override the DSCP value configured in the frame with the * intention to only upgrade the access category. That said, it is not * intended to downgrade the access category for the frames. * Set the value to QCA_WLAN_AC_BK if the QoS upgrade needs to be * disabled, as BK is of the lowest priority and an upgrade to it does * not result in any changes for the frames. * * This attribute behavior is similar to * QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE with the difference that * only UDP frames of BE or BK access category are upgraded and not * UDP frames of VI or VO access category. * * This attribute is not recommended to be used as it blindly forces all * UDP packets of BE or BK access category to a higher access category * which could impact the traffic pattern of all apps using UDP and can * cause unknown behavior. */ QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE_FOR_BE_BK = 84, /* 8-bit unsigned value to configure the driver to enable/disable the * periodic sounding for Tx beamformer functionality. The default * behavior uses algorithm to do sounding based on packet stats. * * 0 - Default behavior. * 1 - Enable the periodic sounding for Tx beamformer. * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_CONFIG_BEAMFORMER_PERIODIC_SOUNDING = 85, /* 8-bit unsigned value, whenever wifi calling (wfc) begin or end, * Userspace sends this information to driver/firmware to configure * wfc state. Driver/Firmware uses this information to * optimize power savings, rate adaption, roaming, etc. * * 1 - wfc is on. * 0 - wfc is off. */ QCA_WLAN_VENDOR_ATTR_CONFIG_WFC_STATE = 86, /* 8-bit unsigned value to configure the driver to enable/disable the * EHT EML capability in management frame EHT capabilities. * 1 - Enable, 0 - Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_EML_CAPABILITY = 87, /* 8-bit unsigned value to configure the driver with EHT MLO max * simultaneous links to be used for MLO connection. * The range of the value is 0 to 14. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_SIMULTANEOUS_LINKS = 88, /* 8-bit unsigned value to configure the driver with EHT MLO maximum * number of links to be used for MLO connection. * The range of the value is 1 to 16. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_NUM_LINKS = 89, /* 8-bit unsigned value to configure the driver with EHT MLO mode. * Uses enum qca_wlan_eht_mlo_mode values. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MODE = 90, /* Nested attribute with frequencies in u32 attributes to configure a * list of allowed 20 MHz channel center frequencies in MHz for AP * operation. Whenever performing a channel selection operation, the * driver shall generate a new list based on this provided list by * filtering out channels that cannot be used at that time due to * regulatory or other constraints. The resulting list is used as the * list of all allowed channels, i.e., operation on any channel that is * not included is not allowed, whenever performing operations like ACS * and DFS. * * Userspace shall configure this before starting the AP and the * configuration is valid only from the next BSS start and until the * BSS is stopped. The driver shall clear this configuration when the * AP is stopped and fall back to the default behavior for subsequent * AP operation. * * The default behavior when this configuration is not applicable is the * driver can choose any of the channels supported by the hardware * except the channels that cannot be used due to regulatory or other * constraints. * * The driver shall reject this configuration if done after the AP is * started. This attribute can be used to specify user's choice of * frequencies and static puncture channel list, etc. */ QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST = 91, /* Nested attribute to indicate EHT MLO links to be forced active. * It contains link MAC address attributes. These nested attributes are * of the type NL80211_ATTR_MAC and are used to force enabling of the * MLO links corresponding to the indicated link MAC addresses. * Subsequently, the links corresponding to the link MAC addresses that * are not indicated are forced inactive. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_ACTIVE_LINKS = 92, /* 8-bit unsigned value to configure EMLSR mode entry or exit. * Uses enum qca_wlan_emlsr_mode values. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EMLSR_MODE_SWITCH = 93, /* 8-bit unsigned value. This attribute is used to dynamically * enable/suspend trigger based UL MU transmission. * This is supported in STA mode and the device sends Operating * Mode Indication to inform the change as described in * IEEE Std 802.11ax-2021, 26.9. * * This attribute can be configured when the STA is associated * to an AP and the configuration is maintained until the current * association terminates. * * By default all UL MU transmissions are enabled. * * Uses enum qca_ul_mu_config values. */ QCA_WLAN_VENDOR_ATTR_CONFIG_UL_MU_CONFIG = 95, /* 8-bit unsigned value. Optionally specified along with * %QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH when STA is in connected * state. This configuration is applicable only for the current * connection. This configuration not allowed in disconnected state. * This configuration can be sent inside * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINKS to specify the maximum * supported channel width update type per-MLO link. * * valid values: * 0 - The maximum allowed bandwidth change is applicable for both Tx * and Rx paths. The driver shall conduct OMI operation as defined * in 26.9 (Operating mode indication) or OMN operation as * defined in 11.40 (Notification of operating mode * changes) in IEEE P802.11-REVme/D2.0 with AP to indicate the * change in the maximum allowed operating bandwidth. * 1 - Limit the change in maximum allowed bandwidth only to Tx path. * In this case the driver doesn't need to conduct OMI/OMN * operation since %QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH is * expected to be less than the current connection maximum * negotiated bandwidth. * For example: Negotiated maximum bandwidth is 160 MHz and the new * maximum bandwidth configured is 80 MHz, now the driver limits * the maximum bandwidth to 80 MHz only in the Tx path. */ QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE = 96, /* 8-bit unsigned value to set EPCS (Emergency Preparedness * Communications Service) feature capability * 1 - Enable, 0 - Disable. * * This configuration is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EPCS_CAPABILITY = 97, /* 8-bit unsigned value to enable/disable EPCS priority access * 1 - Enable, 0 - Disable. * The EPCS priority access shall be enabled only when EPCS feature * capability is also enabled (see * QCA_WLAN_VENDOR_ATTR_CONFIG_EPCS_CAPABILITY). * * This configuration is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_CONFIG_EPCS_FUNCTION = 98, /* 8-bit unsigned value. Used to specify the MLO link ID of a link * that is being configured. This attribute must be included in each * record nested inside %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINKS, and * may be included without nesting to indicate the link that is the * target of other configuration attributes. */ QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID = 99, /* Array of nested links each identified by * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID. This uses values defined in * enum qca_wlan_vendor_attr_config, explicit documentation shall be * added for the attributes in enum qca_wlan_vendor_attr_config to * support per-MLO link configuration through * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINKS. * * Userspace can configure a single link or multiple links with this * attribute by nesting the corresponding configuration attributes and * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID for each link. * * Userspace can fetch the configuration attribute values for a single * link or multiple links with this attribute by nesting the * corresponding configuration attributes and * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID for each link. * * For STA interface, this attribute is applicable only in connected * state when the current connection is MLO capable. The valid values of * %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID are the link IDs of the * connected AP MLD links. * * For AP interface, this configuration applicable only after adding * MLO links to the AP interface with %NL80211_CMD_ADD_LINK and the * valid values of %QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID are the link * IDs specified in %NL80211_CMD_ADD_LINK while adding the MLO links to * the AP interface. */ QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINKS = 100, /* 16-bit unsigned value to configure power save inactivity timeout in * milliseconds. * * STA enters into power save mode (PM=1) after TX/RX inactivity of time * duration specified by %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO. * * This attribute shall be configured along with * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE_INTERVAL when * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT * is set to %QCA_WLAN_VENDOR_OPM_MODE_USER_DEFINED mode. */ QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO = 101, /* 16-bit unsigned value to configure speculative wake interval in * milliseconds. * * STA speculatively wakes up to look for buffered data by AP at * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE_INTERVAL interval after * entering into power save. If configured zero, STA wakes up at * upcoming DTIM beacon. * * This attribute shall be configured along with * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO and * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT * to %QCA_WLAN_VENDOR_OPM_MODE_USER_DEFINED mode. */ QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE_INTERVAL = 102, /* * 16-bit unsigned value to configure TX max A-MPDU count. * * For STA interface, this attribute is applicable only in connected * state, peer MAC address is not required to be provided. * * For AP interface, this attribute is applicable only in started * state and one of the associated peer STAs must be specified with * QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC. If this is for an ML * association, the peer MAC address provided is the link address of * the non-AP MLD. * * This attribute runtime configures the TX maximum aggregation size. * The value must be in range of 1 to BA window size for the specific * peer. */ QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_AMPDU_CNT = 103, /* * 8-bit unsigned value to configure TID-to-link mapping negotiation * type. * Uses enum qca_wlan_ttlm_negotiation_support values. * * This value applies to the complete AP/non-AP MLD interface, and the * MLD advertises it within the Basic Multi-Link element in the * association frames. If a new value is configured during an active * connection, it will take effect in the subsequent associations and * is not reset during disconnection. * * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TTLM_NEGOTIATION_SUPPORT = 104, /* 8-bit unsigned value * * This attribute configures a traffic shaping mode * applied during coex scenarios. * By default all coex traffic shaping modes are enabled, * i.e., shape WLAN traffic based on coex traffic pattern and priority. * To shape traffic, STA may enter in power save mode * and AP may send CTS-to-self frame. * * Uses enum qca_coex_traffic_shaping_mode values. */ QCA_WLAN_VENDOR_ATTR_CONFIG_COEX_TRAFFIC_SHAPING_MODE = 105, /* 8-bit unsigned value to configure BTM support. * * The attribute is applicable only for STA interface. Uses enum * qca_wlan_btm_support values. This configuration is not allowed in * connected state. */ QCA_WLAN_VENDOR_ATTR_CONFIG_BTM_SUPPORT = 107, /* 16-bit unsigned value to configure client's keep-alive interval in * seconds. The driver will reduce the keep-alive interval to this * configured value if the AP advertises BSS maximum idle period and if * that BSS max idle period is larger than this configured value. If the * AP does not advertise a maximum value, the configured value will be * used as a keep-alive period for unprotected frames. * * This configuration is applicable only during the STA's current * association. */ QCA_WLAN_VENDOR_ATTR_CONFIG_KEEP_ALIVE_INTERVAL = 108, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, }; /** * enum qca_ul_mu_config - UL MU configuration * @QCA_UL_MU_SUSPEND - All trigger based UL MU transmission is suspended * @QCA_UL_MU_ENABLE - All trigger based UL MU transmission is enabled */ enum qca_ul_mu_config { QCA_UL_MU_SUSPEND = 0, QCA_UL_MU_ENABLE = 1, }; /** * enum qca_dbam_config - Specifies DBAM config mode * @QCA_DBAM_DISABLE: Firmware disables DBAM * @QCA_DBAM_ENABLE: Firmware enables DBAM opportunistically when * internal criteria are met. * @QCA_DBAM_FORCE_ENABLE: Firmware enables DBAM forcefully. */ enum qca_dbam_config { QCA_DBAM_DISABLE = 0, QCA_DBAM_ENABLE = 1, QCA_DBAM_FORCE_ENABLE = 2, }; /** * enum qca_wlan_vendor_attr_wifi_logger_start - Enum for wifi logger starting * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID: Invalid attribute * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID: Ring ID * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL: Verbose level * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS: Flag * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST: Last value * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_MAX: Max value */ enum qca_wlan_vendor_attr_wifi_logger_start { QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, }; /* * enum qca_wlan_vendor_attr_wifi_logger_get_ring_data - Get ring data * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_INVALID: Invalid attribute * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_ID: Ring ID * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST: Last value * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_MAX: Max value */ enum qca_wlan_vendor_attr_wifi_logger_get_ring_data { QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_ID = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST - 1, }; #ifdef WLAN_FEATURE_OFFLOAD_PACKETS /** * enum wlan_offloaded_packets_control - control commands * @WLAN_START_OFFLOADED_PACKETS: start offloaded packets * @WLAN_STOP_OFFLOADED_PACKETS: stop offloaded packets * */ enum wlan_offloaded_packets_control { WLAN_START_OFFLOADED_PACKETS = 1, WLAN_STOP_OFFLOADED_PACKETS = 2 }; /** * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication * * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to * the offloaded data. * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded * data. * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload * indication. */ enum qca_wlan_vendor_attr_data_offload_ind { QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, /* keep last */ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS. */ enum qca_wlan_vendor_attr_offloaded_packets { QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, /* Takes valid value from the enum * qca_wlan_offloaded_packets_sending_control * Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, /* array of u8 len: Max packet size */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, /* 6-byte MAC address used to represent source MAC address */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, /* 6-byte MAC address used to represent destination MAC address */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, /* Unsigned 32-bit value, in milli seconds */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, /* This optional unsigned 16-bit attribute is used for specifying * ethernet protocol type. If not specified ethertype defaults to IPv4. */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_ETHER_PROTO_TYPE, /* keep last */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, }; #endif /* WLAN_FEATURE_OFFLOAD_PACKETS */ /** * enum qca_wlan_rssi_monitoring_control - rssi control commands * @QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID: invalid * @QCA_WLAN_RSSI_MONITORING_START: rssi monitoring start * @QCA_WLAN_RSSI_MONITORING_STOP: rssi monitoring stop */ enum qca_wlan_rssi_monitoring_control { QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, QCA_WLAN_RSSI_MONITORING_START, QCA_WLAN_RSSI_MONITORING_STOP, }; /** * enum qca_wlan_vendor_attr_rssi_monitoring - rssi monitoring * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID: Invalid * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL: control * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI: max rssi * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI: min rssi * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID: current bssid * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI: current rssi * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST: after last * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX: max */ enum qca_wlan_vendor_attr_rssi_monitoring { QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, /* attributes to be used/received in callback */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, /* keep last */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_NDP. * @QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID * @QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD: sub commands values in qca_wlan_ndp_sub_cmd * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID: * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID: indicates a service info * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL: channel frequency in MHz * @QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR: Interface Discovery MAC * address * @QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR: Interface name on which NDP is being * created * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY: CONFIG_SECURITY is deprecated, use * NCS_SK_TYPE/PMK/SCID instead * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS: value for QoS * @QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO: app info * @QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID: NDP instance Id * @QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY: Array of instance Ids * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE: initiator/responder NDP response * code: accept/reject * @QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR: NDI MAC address * @QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE: errors types returned by * driver * @QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE: value error values returned by * driver * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG: Channel setup configuration * @QCA_WLAN_VENDOR_ATTR_NDP_CSID: Cipher Suite Shared Key Type * @QCA_WLAN_VENDOR_ATTR_NDP_PMK: PMK_INFO * @QCA_WLAN_VENDOR_ATTR_NDP_SCID: Security Context Identifier that contains the * PMKID * @QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE: passphrase * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME: service name * @QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON: bitmap indicating schedule * update: * BIT_0: NSS Update * BIT_1: Channel list update * @QCA_WLAN_VENDOR_ATTR_NDP_NSS: nss * @QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS: NUMBER NDP CHANNEL * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH: CHANNEL BANDWIDTH: * 0:20 MHz, * 1:40 MHz, * 2:80 MHz, * 3:160 MHz * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO: Array of channel/band width * @QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR: IPv6 address used by NDP, 16 bytes array * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT: Unsigned 16-bit value indicating * transport port used by NDP. * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL: Unsigned 8-bit value indicating * protocol used by NDP and assigned by the Internet Assigned Numbers Authority * as per: www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml * @QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT: Unsigned 8-bit value indicating if * NDP remote peer supports NAN NDPE. 1:support 0:not support * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_ID: As per Wi-Fi Aware Specification v3.2 * Service Id is the first 48 bits of the SHA-256 hash of the Service Name. * A lower-case representation of the Service Name shall be used to * calculate the Service ID. * Array of u8: length is 6 bytes * This attribute is used and optional for ndp indication. * @QCA_WLAN_VENDOR_ATTR_NDP_CSIA_CAPABILITIES: Unsigned 8-bit value for Cipher * Suite * This attribute is used and optional in ndp request, ndp response, ndp * indication, and ndp confirm. * This attribute is used to indicate the Capabilities field of Cipher Suite * Information attribute (CSIA) of NDP frames as defined in Wi-Fi Aware * Specification v4.0, 9.5.21.2, Table 122. * Firmware can accept or ignore any of the capability bits. * @QCA_WLAN_VENDOR_ATTR_NDP_GTK_REQUIRED: Indicate if the GTK protection is * required for NDP. NLA_FLAG attribute. * This attribute can be used in ndp request, ndp response, ndp indication, and * ndp confirm. * GTK protection required is indicated in the NDPE attribute of NAN action * frame (NAF) during NDP negotiation as defined in Wi-Fi Aware Specification * v4.0, 9.5.16.2. * If the device and peer supports GTKSA and if GTK protection required bit is * set in NDPE IE, devices will share GTK to each other in SKDA of Data Path * Security Confirm and Data Path Security Install frames of NDP negotiation to * send and receive protected group addressed data frames from each other. * @QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST: id after last valid attribute * @QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX: max value of this enum type */ enum qca_wlan_vendor_attr_ndp_params { QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD = 1, QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID = 2, QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID = 3, QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL = 4, QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR = 5, QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR = 6, QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY = 7, QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS = 8, QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO = 9, QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID = 10, QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY = 11, QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE = 12, QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR = 13, QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE = 14, QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE = 15, QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG = 16, QCA_WLAN_VENDOR_ATTR_NDP_CSID = 17, QCA_WLAN_VENDOR_ATTR_NDP_PMK = 18, QCA_WLAN_VENDOR_ATTR_NDP_SCID = 19, QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE = 20, QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME = 21, QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON = 22, QCA_WLAN_VENDOR_ATTR_NDP_NSS = 23, QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS = 24, QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH = 25, QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO = 26, QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT = 30, QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_ID = 31, QCA_WLAN_VENDOR_ATTR_NDP_CSIA_CAPABILITIES = 32, QCA_WLAN_VENDOR_ATTR_NDP_GTK_REQUIRED = 33, /* keep last */ QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, }; /** * enum qca_wlan_ndp_sub_cmd - NDP sub commands types for * QCA_NL80211_VENDOR_SUBCMD_NDP. * @QCA_WLAN_VENDOR_ATTR_NDP_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE: Command to create a NAN * data path interface. * This command was initially designed to both create and start a NAN * data path interface. However, changes to Linux 5.12 no longer allow * interface creation via vendor commands. When the driver advertises * QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI * userspace must explicitly first create the interface using * NL80211_CMD_NEW_INTERFACE before subsequently invoking this command * to start the interface. * @QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE: command to delete a NAN * data path interface. * This command was initially designed to both stop and delete a NAN * data path interface. However, changes to Linux 5.12 no longer allow * interface deletion via vendor commands. When the driver advertises * QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI * userspace must explicitly delete the interface using * NL80211_CMD_DEL_INTERFACE after calling this command. * @QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE: response for above * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST: respond to ndp session * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE: response for above * @QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST: initiate a ndp end * @QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE: response for above * @QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND: notify the peer about the end request * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND: confirm the ndp session is complete * @QCA_WLAN_VENDOR_ATTR_NDP_END_IND: indicate the peer about the end request * being received * @QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND: indicate the peer of schedule * update */ enum qca_wlan_ndp_sub_cmd { QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 }; /** * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel * information. These attributes are sent as part of * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following * attributes correspond to a single channel. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS: A bitmask (u16) * with flags specified in qca_wlan_vendor_channel_prop_flags_ext. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT: A bitmask (u16) * with flags specified in qca_wlan_vendor_channel_prop_flags_ext. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ: frequency * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER: maximum * regulatory transmission power * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER: maximum * transmission power * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER: minimum * transmission power * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID: regulatory * class id * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN: maximum * antenna gain in dbm * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0: vht segment 0 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1: vht segment 1 * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0: Segment 0 * center frequency in MHz. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0: vht * segment 0 in center freq in MHz. (this is the legacy alias) * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1: Segment 1 * center frequency in MHz. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1: vht * segment 1 in center freq in MHz. (this is the legacy alias) * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_SUPP_POWER_MODES: 3-bits * flag indicating the AP power modes supported by the channel, as given by * enum qca_wlan_vendor_external_acs_chan_power_level. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR: Array of nested * attributes for each power mode. It takes attr as defined in enum * qca_wlan_vendor_external_acs_event_chan_power_info_attr. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_OVERLAP_SEG_1: * This indicates the overlapping 320 MHz center frequency in MHz, if the * given primary channel supports more than one 320 MHz channel bonding. * */ enum qca_wlan_vendor_external_acs_event_chan_info_attr { QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, /* * A bitmask (u32) with flags specified in * enum qca_wlan_vendor_channel_prop_flags_2. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, /* * Segment 0 in MHz (u32). * * For 20/40/80 MHz bandwidth, this indicates the channel center * frequency index for the 20/40/80 MHz operating channel. * For 160 MHz bandwidth, this indicates the channel center * frequency of the primary 80 MHz channel. * For 320 MHz bandwidth, indicates the channel center frequency * of the primary 160 MHz channel. * * To maintain backward compatibility, * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 * is also maintained. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0 = 12, /* Legacy alias for the Segment 0 attribute. * * VHT segment 0 in MHz (u32) and the attribute is mandatory. * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 * along with * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0. * * If both the driver and user-space application supports the 6 GHz * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 * is deprecated and * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 * should be used. * * To maintain backward compatibility, * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 * is still used if either of the driver or user space application * doesn't support the 6 GHz band. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 = QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0, /* * Segment 1 in MHz (u32). * * For 20/40/80 MHz bandwidth, this is set to 0. * For 160 MHz bandwidth, indicates the channel center frequency of the * 160 MHz channel. * For 320 MHz bandwidth, indicates the channel center frequency of the * 320 MHz channel. * * To maintain backward compatibility, * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 * is also maintained. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1 = 13, /* Legacy alias for the Segment 1 attribute. * * VHT segment 1 in MHz (u32) and the attribute is mandatory. * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 * along with * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1. * * If both the driver and user-space application supports the 6 GHz * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 * is deprecated and * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 * should be considered. * * To maintain backward compatibility, * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 * is still used if either of the driver or user space application * doesn't support the 6 GHz band. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 = QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1, /* * 16-bit attribute of bits indicating the AP power modes supported by * the channel (u16). * Note: Currently, only 3 bits are used in the attribute and each bit * corresponds to the power mode mentioned in enum * qca_wlan_vendor_external_acs_chan_power_level and a given bit is * set if the associated mode is supported. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_SUPP_POWER_MODES = 14, /* Array of nested attributes for each power mode. It takes attr as * defined in enum * qca_wlan_vendor_external_acs_event_chan_power_info_attr. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR = 15, /* * This indicates the overlapping 320 MHz center frequency in MHz * (u32), if the given primary channel supports more than one * 320 MHz channel bonding. * * Example: * For 6 GHz, channel frequency 6115 MHz (channel number 33) segment 0 * center frequency (primary 160 MHz) is 6185 MHz and there can be two * possible segment 2 frequencies for this (320 MHz center * frequencies): * * 1) Center frequency 6105 MHz (channel 31): 320 MHz channel bonding * from frequency 5945 MHz - 6265 MHz * 2) Center frequency 6265 MHz (channel 63): 320 MHz channel bonding * from frequency 6105 MHz - 6425 MHz * * In this case, * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0 will * return 6185 MHz. * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1 will * return 6105 MHz. * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_OVERLAP_SEG_1 * will return 6265 MHz. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_OVERLAP_SEG_1 = 16, /* keep last */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, }; /** * qca_wlan_vendor_external_acs_chan_power_level - Specifies the valid * values that the vendor external ACS channel power attribute * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_MODE can * take. * @QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_LOW_POWER: Low power/Indoor mode * @QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_STANDARD_POWER: Standard power mode * @QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_VERY_LOW_POWER: Very low power mode */ enum qca_wlan_vendor_external_acs_chan_power_level { QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_LOW_POWER = 0, QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_STANDARD_POWER = 1, QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_VERY_LOW_POWER = 2, }; /** * qca_wlan_vendor_external_acs_event_chan_power_info_attr: Represents nested * attributes for power mode type and power values corresponding to that. * These attributes are sent as part of * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR. */ enum qca_wlan_vendor_external_acs_event_chan_power_info_attr { QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_INVALID = 0, /* * Power mode (u8) takes the values defined in enum * qca_wlan_vendor_external_acs_chan_power_mode */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_MODE = 1, /* * Indicates if power value is a PSD/EIRP value (flag). If flag is * present, it indicates a PSD value. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_PSD_FLAG = 2, /* * Power value (u32) PSD/EIRP as indicated by * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_PSD_FLAG, * for power mode corresponding to the * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_MODE. * Units for PSD - dBm/MHz * Units for EIRP - dBm */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_VALUE = 3, /* keep last */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_LAST, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_MAX = QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_LAST - 1, }; /** * enum qca_wlan_vendor_attr_start_acs_config: attribute to vendor sub-command * QCA_NL80211_VENDOR_SUBCMD_START_ACS. This will be triggered by host * driver. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON: This reason refers to * qca_wlan_vendor_acs_select_reason. This helps acs module to understand why * ACS need to be started * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED: Does * driver supports spectral scanning or not * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED: Is 11ac is * offloaded to firmware. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT: Does driver * provides additional channel capability as part of scan operation. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP:Flag attribute to indicate * interface status is UP * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE: Operating mode of * interface. It takes one of nl80211_iftype values. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH: This is the upper bound * of chan width. ACS logic should try to get a channel with specified width * if not found then look for lower values. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND: nl80211_bands * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE: PHY/HW mode such as * a/b/g/n/ac. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST: Supported frequency list * among which ACS should choose best frequency. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL:Preferred Chan List by the * driver which will have format as array of * nested values. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO: Array of nested attribute * for each channel. It takes attr as defined in * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY:External ACS policy such as * PCL mandatory, PCL preferred, etc.It uses values defined in enum * qca_wlan_vendor_attr_external_acs_policy. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO: Reference RF * Operating Parameter (RROP) availability information (u16). It uses values * defined in enum qca_wlan_vendor_attr_rropavail_info. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AFC_CAPABILITY: Flag attribute to * indicate if driver supports 6 GHz AFC trigger for External ACS. */ enum qca_wlan_vendor_attr_external_acs_event { QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AFC_CAPABILITY = 15, /* keep last */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, }; enum qca_iface_type { QCA_IFACE_TYPE_STA, QCA_IFACE_TYPE_AP, QCA_IFACE_TYPE_P2P_CLIENT, QCA_IFACE_TYPE_P2P_GO, QCA_IFACE_TYPE_IBSS, QCA_IFACE_TYPE_TDLS, }; /** * enum qca_wlan_vendor_attr_pcl_config: attribute to vendor sub-command * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST. * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_CHANNEL: pcl channel number * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_WEIGHT: pcl channel weight * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_FREQ: pcl channel frequency * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_FLAG: pcl channel flag bitmask */ enum qca_wlan_vendor_attr_pcl_config { QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3, QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4, }; enum qca_set_band { QCA_SETBAND_AUTO = 0, QCA_SETBAND_5G = BIT(0), QCA_SETBAND_2G = BIT(1), QCA_SETBAND_6G = BIT(2), }; /** * enum set_reset_packet_filter - set packet filter control commands * @QCA_WLAN_SET_PACKET_FILTER: Set Packet Filter * @QCA_WLAN_GET_PACKET_FILTER: Get Packet filter * @QCA_WLAN_WRITE_PACKET_FILTER: Write packet filter program/data * @QCA_WLAN_READ_PACKET_FILTER: Read packet filter program/data * @QCA_WLAN_ENABLE_PACKET_FILTER: Enable APF interpreter * @QCA_WLAN_DISABLE_PACKET_FILTER: Disable APF interpreter */ enum set_reset_packet_filter { QCA_WLAN_SET_PACKET_FILTER = 1, QCA_WLAN_GET_PACKET_FILTER = 2, QCA_WLAN_WRITE_PACKET_FILTER = 3, QCA_WLAN_READ_PACKET_FILTER = 4, QCA_WLAN_ENABLE_PACKET_FILTER = 5, QCA_WLAN_DISABLE_PACKET_FILTER = 6, }; /** * enum qca_wlan_vendor_attr_packet_filter - APF control commands * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID: Invalid * @QCA_WLAN_VENDOR_ATTR_SET_RESET_PACKET_FILTER: Filter ID * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION: Filter Version * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE: Total Length * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET: Current offset * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM: length of APF instructions * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH: length of the program * section in packet filter buffer */ enum qca_wlan_vendor_attr_packet_filter { QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SET_RESET_PACKET_FILTER, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH, /* keep last */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS. */ enum qca_wlan_vendor_attr_wake_stats { QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0, /* Unsigned 32-bit value indicating the total count of wake event */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE, /* Array of individual wake count, each index representing wake reason */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR, /* Unsigned 32-bit value representing wake count array */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ, /* Unsigned 32-bit total wake count value of driver/fw */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE, /* Array of wake stats of driver/fw */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR, /* Unsigned 32-bit total wake count value of driver/fw */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ, /* Unsigned 32-bit total wake count value of packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE, /* Unsigned 32-bit wake count value unicast packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT, /* Unsigned 32-bit wake count value multicast packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value broadcast packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT, /* Unsigned 32-bit wake count value of ICMP packets */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT, /* Unsigned 32-bit wake count value of ICMP6 packets */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT, /* Unsigned 32-bit value ICMP6 router advertisement */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA, /* Unsigned 32-bit value ICMP6 neighbor advertisement */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA, /* Unsigned 32-bit value ICMP6 neighbor solicitation */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS, /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value of receive side multicast */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value of a given RSSI breach */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT, /* Unsigned 32-bit wake count value of low RSSI */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT, /* Unsigned 32-bit value GSCAN count */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT, /* Unsigned 32-bit value PNO complete count */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT, /* Unsigned 32-bit value PNO match count */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT, /* keep last */ QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_thermal_level - Defines various thermal levels * configured by userspace to the driver/firmware. The values will be * encapsulated in QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL attribute. * The driver/firmware takes necessary actions requested by userspace * such as throttling wifi tx etc. in order to mitigate high temperature. * * @QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE: Stop/clear all throttling actions. * @QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT: Throttle tx lightly. * @QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE: Throttle tx moderately. * @QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE: Throttle tx severely. * @QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL: Critical thermal level reached. * @QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY: Emergency thermal level reached. */ enum qca_wlan_vendor_thermal_level { QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE = 0, QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT = 1, QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE = 2, QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE = 3, QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL = 4, QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY = 5, }; /** * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set * cmd value. Used for NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. */ enum qca_wlan_vendor_attr_thermal_cmd { QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0, /* The value of command, driver will implement different operations * according to this value. It uses values defined in * enum qca_wlan_vendor_attr_thermal_cmd_type. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1, /* Userspace uses this attribute to configure thermal level to the * driver/firmware, or get thermal level from the driver/firmware. * Used in request or response, u32 attribute, * possible values are defined in enum qca_wlan_vendor_thermal_level. */ QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL = 2, /* Userspace uses this attribute to configure the time in which the * driver/firmware should complete applying settings it received from * userspace with QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL * command type. Used in request, u32 attribute, value is in * milliseconds. A value of zero indicates to apply the settings * immediately. The driver/firmware can delay applying the configured * thermal settings within the time specified in this attribute if * there is any critical ongoing operation. */ QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW = 3, /* Nested attribute, driver/firmware uses this attribute to report * thermal stats of different thermal levels to userspace when requested * using QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS command * type. This attribute contains nested array of records of thermal * statistics of multiple levels. The attributes used inside this nested * attribute are defined in enum qca_wlan_vendor_attr_thermal_stats. */ QCA_WLAN_VENDOR_ATTR_THERMAL_STATS = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1 }; /** * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the * thermal command types sent to driver. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to * get thermal shutdown configuration parameters for display. Parameters * responded from driver are defined in * enum qca_wlan_vendor_attr_get_thermal_params_rsp. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to * get temperature. Host should respond with a temperature data. It is defined * in enum qca_wlan_vendor_attr_thermal_get_temperature. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal * suspend action. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal * resume action. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL: Configure thermal level to * the driver/firmware. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_LEVEL: Request to get the current * thermal level from the driver/firmware. The driver should respond with a * thermal level defined in enum qca_wlan_vendor_thermal_level. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS: Request to get the * current thermal stats from the driver/firmware. The driver should respond * with stats of all thermal levels encapsulated in attribute * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS: Request to clear * the current thermal stats all thermal levels maintained in the * driver/firmware and start counting from zero again. */ enum qca_wlan_vendor_attr_thermal_cmd_type { QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_LEVEL, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS, }; /** * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes * to get chip temperature by user. * enum values are used for NL attributes for data used by * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. */ enum qca_wlan_vendor_attr_thermal_get_temperature { QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0, /* Temperature value (degree Celsius) from driver. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to * report thermal events from driver to user space. * enum values are used for NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command. */ enum qca_wlan_vendor_attr_thermal_event { QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0, /* Temperature value (degree Celsius) from driver. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE, /* Indication of resume completion from power save mode. * NLA_FLAG attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE, /* Thermal level from the driver. * u32 attribute. Possible values are defined in * enum qca_wlan_vendor_thermal_level. */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_LEVEL = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1, }; /** * enum qca_vendor_element_id - QCA Vendor Specific element types * * These values are used to identify QCA Vendor Specific elements. The * payload of the element starts with the three octet OUI (OUI_QCA) and * is followed by a single octet type which is defined by this enum. * * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. * This element can be used to specify preference order for supported * channels. The channels in this list are in preference order (the first * one has the highest preference) and are described as a pair of * (global) Operating Class and Channel Number (each one octet) fields. * * This extends the standard P2P functionality by providing option to have * more than one preferred operating channel. When this element is present, * it replaces the preference indicated in the Operating Channel attribute. * For supporting other implementations, the Operating Channel attribute is * expected to be used with the highest preference channel. Similarly, all * the channels included in this Preferred channel list element are * expected to be included in the Channel List attribute. * * This vendor element may be included in GO Negotiation Request, P2P * Invitation Request, and Provision Discovery Request frames. * * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID. The payload of this * vendor specific element is defined by the latest P802.11ax draft. * Please note that the draft is still work in progress and this element * payload is subject to change. * * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID. The payload of this * vendor specific element is defined by the latest P802.11ax draft. * Please note that the draft is still work in progress and this element * payload is subject to change. * * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set * element). * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID extension. The payload of * this vendor specific element is defined by the latest P802.11ax draft * (not including the Element ID Extension field). Please note that the * draft is still work in progress and this element payload is subject to * change. * * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID extension. The payload of * this vendor specific element is defined by the latest P802.11ax draft * (not including the Element ID Extension field). Please note that the * draft is still work in progress and this element payload is subject to * change. * * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID extension. The payload of * this vendor specific element is defined by the latest P802.11ax draft * (not including the Element ID Extension field). Please note that the * draft is still work in progress and this element payload is subject to * change. */ enum qca_vendor_element_id { QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, QCA_VENDOR_ELEM_HE_CAPAB = 1, QCA_VENDOR_ELEM_HE_OPER = 2, QCA_VENDOR_ELEM_RAPS = 3, QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, }; /** * enum qca_vendor_attr_tsf_cmd: Vendor attributes for TSF capture * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: Required (u32) * Specify the TSF command. Possible values are defined in * &enum qca_tsf_cmd. * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Optional (u64) * This attribute contains TSF timer value. This attribute is only available * in %QCA_TSF_GET or %QCA_TSF_SYNC_GET response. * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Optional (u64) * This attribute contains SOC timer value at TSF capture. This attribute is * only available in %QCA_TSF_GET or %QCA_TSF_SYNC_GET response. * @QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL: Optional (u32) * This attribute is used to provide TSF sync interval and only applicable when * TSF command is %QCA_TSF_SYNC_START. If this attribute is not provided, the * driver will use the default value. Time unit is in milliseconds. */ enum qca_vendor_attr_tsf_cmd { QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TSF_CMD, QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL, QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TSF_MAX = QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 }; /** * enum qca_tsf_cmd: TSF driver commands * @QCA_TSF_CAPTURE: Initiate TSF Capture * @QCA_TSF_GET: Get TSF capture value * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value * @QCA_TSF_AUTO_REPORT_ENABLE: Used in STA mode only. Once set, the target * will automatically send TSF report to the host. To query * %QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY, this operation needs to be * initiated first. * @QCA_TSF_AUTO_REPORT_DISABLE: Used in STA mode only. Once set, the target * will not automatically send TSF report to the host. If * %QCA_TSF_AUTO_REPORT_ENABLE is initiated and * %QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY is not queried anymore, this * operation needs to be initiated. * @QCA_TSF_SYNC_START: Start periodic TSF sync feature. The driver periodically * fetches TSF and host time mapping from the firmware with interval configured * through the %QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL attribute. If the * interval value is not provided the driver will use the default value. The * userspace can query the TSF and host time mapping via the %QCA_TSF_GET * command. * @QCA_TSF_SYNC_STOP: Stop periodic TSF sync feature. */ enum qca_tsf_cmd { QCA_TSF_CAPTURE, QCA_TSF_GET, QCA_TSF_SYNC_GET, QCA_TSF_AUTO_REPORT_ENABLE, QCA_TSF_AUTO_REPORT_DISABLE, QCA_TSF_SYNC_START, QCA_TSF_SYNC_STOP, }; /** * enum qca_vendor_attr_get_preferred_freq_list - get preferred channel list * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE: interface type * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST: preferred frequency list * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL: pcl with weight * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST: after last * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX: max */ enum qca_vendor_attr_get_preferred_freq_list { QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, /* A 32-unsigned value; the interface type/mode for which the preferred * frequency list is requested (see enum qca_iface_type for possible * values); used in both south- and north-bound. */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, /* An array of 32-unsigned values; values are frequency (MHz); used * in north-bound only. */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, /* An array of nested values as per enum * qca_wlan_vendor_attr_pcl_config attribute. * Each element contains frequency (MHz), weight, and flag * bit mask indicating how the frequency should be used in P2P * negotiation. */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL, /* keep last */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 }; /** * enum qca_vendor_attr_probable_oper_channel - channel hint * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE: interface type * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ: frequency hint value * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST: last * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX: max */ enum qca_vendor_attr_probable_oper_channel { QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, /* 32-bit unsigned value; indicates the connection/iface type likely to * come on this channel (see enum qca_iface_type). */ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, /* keep last */ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_gw_param_config - gateway param config * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_INVALID: Invalid * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_GW_MAC_ADDR: gateway mac addr * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV4_ADDR: ipv4 addr * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV6_ADDR: ipv6 addr */ enum qca_wlan_vendor_attr_gw_param_config { QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_GW_MAC_ADDR, QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV4_ADDR, QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV6_ADDR, QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_AFTER_LAST - 1, }; /** * enum drv_dbs_capability - DBS capability * @DRV_DBS_CAPABILITY_DISABLED: DBS disabled * @DRV_DBS_CAPABILITY_1X1: 1x1 * @DRV_DBS_CAPABILITY_2X2: 2x2 */ enum drv_dbs_capability { DRV_DBS_CAPABILITY_DISABLED, /* not supported or disabled */ DRV_DBS_CAPABILITY_1X1, DRV_DBS_CAPABILITY_2X2, }; /** * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease * * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. */ enum qca_vendor_attr_txpower_decr_db { QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, /* * 8-bit unsigned value to indicate the reduction of TX power in dB for * a virtual interface. */ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, /* keep last */ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 }; /** * enum qca_vendor_attr_ota_test - Enable OTA test * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable OTA test * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST: after last * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX: max */ enum qca_vendor_attr_ota_test { QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, /* 8-bit unsigned value to indicate if OTA test is enabled */ QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, /* keep last */ QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 }; /** enum qca_vendor_attr_txpower_scale - vendor sub commands index * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST: last value * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX: max value */ enum qca_vendor_attr_txpower_scale { QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, /* 8-bit unsigned value to indicate the scaling of tx power */ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, /* keep last */ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 }; /** * enum qca_vendor_attr_txpower_scale_decr_db - vendor sub commands index * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB: scaling value * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST: last value * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_MAX: max value */ enum qca_vendor_attr_txpower_scale_decr_db { QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_INVALID, /* 8-bit unsigned value to indicate the scaling of tx power */ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB, /* keep last */ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_MAX = QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST - 1 }; /** * enum dfs_mode - state of DFS mode * @DFS_MODE_NONE: DFS mode attribute is none * @DFS_MODE_ENABLE: DFS mode is enabled * @DFS_MODE_DISABLE: DFS mode is disabled * @DFS_MODE_DEPRIORITIZE: Deprioritize DFS channels in scanning */ enum dfs_mode { DFS_MODE_NONE, DFS_MODE_ENABLE, DFS_MODE_DISABLE, DFS_MODE_DEPRIORITIZE }; /** * enum qca_wlan_vendor_attr_acs_config - Defines Configuration attributes * used by the vendor command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY. * * @QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE: Required (u8) * DFS mode for ACS operation from enum qca_acs_dfs_mode. * * @QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT: Required (u8) * channel number hint for ACS operation, if valid channel is specified then * ACS operation gives priority to this channel. * Note: If both the driver and user space application supports the 6 GHz band, * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT * should be used. * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT * is still used if either of the driver or user space application doesn't * support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT: Required (u32). * Channel center frequency (MHz) hint for ACS operation, if a valid center * frequency is specified, ACS operation gives priority to this channel. */ enum qca_wlan_vendor_attr_acs_config { QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE = 1, QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT = 2, QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT = 3, QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX = QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability */ enum qca_wlan_vendor_attr_get_hw_capability { QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, /* * Antenna isolation * An attribute used in the response. * The content of this attribute is encoded in a byte array. Each byte * value is an antenna isolation value. The array length is the number * of antennas. */ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, /* * Request HW capability * An attribute used in the request. * The content of this attribute is a u32 array for one or more of * hardware capabilities (attribute IDs) that are being requested. Each * u32 value has a value from this * enum qca_wlan_vendor_attr_get_hw_capability * identifying which capabilities are requested. */ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, /* keep last */ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_sta_connect_roam_policy_config - * config params for sta roam policy * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_INVALID: Invalid * @QCA_WLAN_VENDOR_ATTR_STA_DFS_MODE: If sta should skip Dfs channels * @QCA_WLAN_VENDOR_ATTR_STA_SKIP_UNSAFE_CHANNEL: * If sta should skip unsafe channels or not in scanning * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_LAST: * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_MAX: max attribute */ enum qca_wlan_vendor_attr_sta_connect_roam_policy_config { QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_STA_DFS_MODE, QCA_WLAN_VENDOR_ATTR_STA_SKIP_UNSAFE_CHANNEL, QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_MAX = QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_AFTER_LAST - 1, }; /* Attributes for FTM commands and events */ /** * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities * * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See * enum qca_wlan_vendor_attr_loc_capa_flags. * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number * of measurement sessions that can run concurrently. * Default is one session (no session concurrency). * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique * peers that are supported in running sessions. For example, * if the value is 8 and maximum number of sessions is 2, you can * have one session with 8 unique peers, or 2 sessions with 4 unique * peers each, and so on. * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number * of bursts per peer, as an exponent (2^value). Default is 0, * meaning no multi-burst support. * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number * of measurement exchanges allowed in a single burst. * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement * types. A bit mask (unsigned 32 bit value), each bit corresponds * to an AOA type as defined by enum qca_vendor_attr_aoa_type. */ enum qca_wlan_vendor_attr_loc_capa { QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, /* keep last */ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags * * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver * can be configured as an FTM responder (for example, an AP that * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER * will be supported if set. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION * will be supported if set. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder * supports immediate (ASAP) response. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports * requesting AOA measurements as part of an FTM session. */ enum qca_wlan_vendor_attr_loc_capa_flags { QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, }; /** * enum qca_wlan_ani_setting - ANI setting type * @QCA_WLAN_ANI_SETTING_AUTO: Automatically determine ANI level * @QCA_WLAN_ANI_SETTING_FIXED: Fix ANI level to the dBm parameter */ enum qca_wlan_ani_setting { QCA_WLAN_ANI_SETTING_AUTO = 0, QCA_WLAN_ANI_SETTING_FIXED = 1, }; /** * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration * * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL: Optional (u8) * Channel number on which Access Point should restart. * Note: If both the driver and user space application supports the 6 GHz band, * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY * should be used. * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL * is still used if either of the driver or user space application doesn't * support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST: Required * Nested attribute to hold list of center frequencies on which AP is * expected to operate. This is irrespective of ACS configuration. * This list is a priority based one and is looked for before the AP is * created to ensure the best concurrency sessions (avoid MCC and use DBS/SCC) * co-exist in the system. * * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY: Optional (u32) * Channel center frequency (MHz) on which the access point should restart. */ enum qca_wlan_vendor_attr_sap_config { QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL = 1, QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY = 3, /* Keep last */ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_info: Information about * a single peer in a measurement session. * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for * list of supported attributes. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for * secure measurement. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA * measurement every bursts. If 0 or not specified, * AOA measurements will be disabled for this peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where * the measurement frames are exchanged. Optional; if not * specified, try to locate the peer in the kernel scan * results cache and use frequency from there. */ enum qca_wlan_vendor_attr_ftm_peer_info { QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, * per-peer * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request * immediate (ASAP) response from peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request * LCI report from peer. The LCI report includes the absolute * location of the peer in "official" coordinates (similar to GPS). * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request * Location civic report from peer. The LCR includes the location * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, * 11.24.6.7 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, * request a secure measurement. * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. */ enum qca_wlan_vendor_attr_ftm_peer_meas_flags { QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, }; /** * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters * * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements * to perform in a single burst. * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to * perform, specified as an exponent (2^value). * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. */ enum qca_wlan_vendor_attr_ftm_meas_param { QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported * peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement * request for this peer. * See enum qca_wlan_vendor_attr_ftm_peer_result_status. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related * to measurement results for this peer. * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when * request failed and peer requested not to send an additional request * for this number of seconds. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, * 9.4.2.22.10. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, * 9.4.2.22.13. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer * overridden some measurement request parameters. See * enum qca_wlan_vendor_attr_ftm_meas_param. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement * results. Each entry is a nested attribute defined * by enum qca_wlan_vendor_attr_ftm_meas. */ enum qca_wlan_vendor_attr_ftm_peer_result { QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_result_status * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results * will be provided. Peer may have overridden some measurement parameters, * in which case overridden parameters will be report by * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable * of performing the measurement request. No more results will be sent * for this peer in this session. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request * failed, and requested not to send an additional request for number * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS * attribute. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation * failed. Request was not sent over the air. */ enum qca_wlan_vendor_attr_ftm_peer_result_status { QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, }; /** * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags * for measurement result, per-peer * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, * measurement completed for this peer. No more results will be reported * for this peer in this session. */ enum qca_wlan_vendor_attr_ftm_peer_result_flags { QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, }; /** * enum qca_vendor_attr_loc_session_status: Session completion status code * * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed * successfully. * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted * by request. * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request * was invalid and was not started. * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error * and did not complete normally (for example out of resources). */ enum qca_vendor_attr_loc_session_status { QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, }; /** * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data * * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as * recorded by responder, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at * initiator, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by * initiator, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at * responder, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded * during this measurement exchange. Optional and will be provided if * the hardware can measure it. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by * responder. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by * responder. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by * initiator. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by * initiator. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. */ enum qca_wlan_vendor_attr_ftm_meas { QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_p2p_listen_offload - vendor sub commands index * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID: invalid value * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL: * A 32-bit unsigned value; the P2P listen frequency (MHz); must be one * of the social channels. * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD: listen offload period * A 32-bit unsigned value; the P2P listen offload period (ms). * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL: * A 32-bit unsigned value; the P2P listen interval duration (ms). * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT: * A 32-bit unsigned value; number of interval times the Firmware needs * to run the offloaded P2P listen operation before it stops. * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES: device types * An array of unsigned 8-bit characters; vendor information elements. * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE: vendor IEs * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG: control flag for FW * A 32-bit unsigned value; a control flag to indicate whether listen * results need to be flushed to wpa_supplicant. * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON: offload stop reason * A 8-bit unsigned value; reason code for P2P listen offload stop * event. * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST: last value * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX: max value */ enum qca_wlan_vendor_attr_p2p_listen_offload { QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, /* keep last */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_drv_info - WLAN driver info * @QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID: Invalid * @QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE: Maximum Message size info * between Firmware & Host. */ enum qca_wlan_vendor_drv_info { QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, /* keep last */ QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type * * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest * CIR (channel impulse response) path for each antenna. * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude * of the strongest CIR path for each antenna. */ enum qca_wlan_vendor_attr_aoa_type { QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX }; /** * enum qca_wlan_vendor_attr_encryption_test - Attributes to * validate encryption engine * * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. * This will be included if the request is for decryption; if not included, * the request is treated as a request for encryption by default. * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value * indicating the key cipher suite. Takes same values as * NL80211_ATTR_KEY_CIPHER. * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value * Key Id to be used for encryption * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. * Key (TK) to be used for encryption/decryption * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. * Packet number to be specified for encryption/decryption * 6 bytes for TKIP/CCMP/GCMP. * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values * representing the 802.11 packet (header + payload + FCS) that * needs to be encrypted/decrypted. * Encrypted/decrypted response from the driver will also be sent * to userspace with the same attribute. */ enum qca_wlan_vendor_attr_encryption_test { QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, /* keep last */ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of * sector for DMG RF sector operations. * * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector */ enum qca_wlan_vendor_attr_dmg_rf_sector_type { QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX }; /** * enum qca_wlan_vendor_attr_fw_state - State of firmware * * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active */ enum qca_wlan_vendor_attr_fw_state { QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR, QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE, QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX }; /** * BRP antenna limit mode * * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force * antenna limit, BRP will be performed as usual. * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal * antennas limit. the hardware may use less antennas than the * maximum limit. * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will * use exactly the specified number of antennas for BRP. */ enum qca_wlan_vendor_attr_brp_ant_limit_mode { QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX }; /** * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for * DMG RF sector configuration for a single RF module. * The values are defined in a compact way which closely matches * the way it is stored in HW registers. * The configuration provides values for 32 antennas and 8 distribution * amplifiers, and together describes the characteristics of the RF * sector - such as a beam in some direction with some gain. * * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index * of RF module for this configuration. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge * amplifier gain index. Unsigned 32 bit number containing * bits for all 32 antennas. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge * amplifier gain index. Unsigned 32 bit number containing * bits for all 32 antennas. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge * amplifier gain index. Unsigned 32 bit number containing * bits for all 32 antennas. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values * for first 16 antennas, 2 bits per antenna. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values * for last 16 antennas, 2 bits per antenna. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains * DTYPE values (3 bits) for each distribution amplifier, followed * by X16 switch bits for each distribution amplifier. There are * total of 8 distribution amplifiers. */ enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS configuration to the host driver. * * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode * represents the different TDLS trigger modes. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number * of packets shall meet the criteria for implicit TDLS setup. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx * packets within a duration. * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD to initiate * a TDLS setup. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate * a TDLS Discovery to the Peer. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of * discovery attempts to know the TDLS capability of the peer. A peer is * marked as TDLS not capable if there is no response for all the attempts. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD * number of TX / RX frames meet the criteria for TDLS teardown. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number * (u32) of Tx/Rx packets within a duration * CA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold * corresponding to the RSSI of the peer below which a TDLS * setup is triggered. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold * corresponding to the RSSI of the peer above which * a TDLS teardown is triggered. */ enum qca_wlan_vendor_attr_tdls_configuration { QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, /* Attributes configuring the TDLS Implicit Trigger */ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in * the driver. * * The following are the different values for * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. * * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to * initiate/teardown the TDLS connection to a respective peer comes * from the user space. wpa_supplicant provides the commands * TDLS_SETUP, TDLS_TEARDOWN, TDLS_DISCOVER to do this. * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS * setup/teardown to the eligible peer once the configured criteria * (such as TX/RX threshold, RSSI) is met. The attributes * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to * the different configuration criteria for the TDLS trigger from the * host driver. * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger * the TDLS setup / teardown through the implicit mode, only to the * configured MAC addresses(wpa_supplicant, with tdls_external_control = 1, * configures the MAC address through TDLS_SETUP/TDLS_TEARDOWN commands). * External mode works on top of the implicit mode, thus the host Driver * is expected to be configured in TDLS Implicit mode too to operate in * External mode. Configuring External mode alone without Implicit * mode is invalid. * * All the above implementations work as expected only when the host driver * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - * representing that the TDLS message exchange is not internal to the host * driver, but depends on wpa_supplicant to do the message exchange. */ enum qca_wlan_vendor_tdls_trigger_mode { QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, }; /** * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any * source of SAR power limits, thereby disabling the SAR power * limit feature. * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. * * This enumerates the valid set of values that may be supplied for * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in * the response to an instance of the * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. */ enum qca_vendor_attr_sar_limits_selections { QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, }; /** * enum qca_vendor_attr_sar_limits_spec_modulations - * SAR limits specification modulation * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - * CCK modulation * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - * OFDM modulation * * This enumerates the valid set of values that may be supplied for * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor * command or in the response to an instance of the * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. */ enum qca_vendor_attr_sar_limits_spec_modulations { QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, }; /** * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to * select which SAR power limit table should be used. Valid * values are enumerated in enum * %qca_vendor_attr_sar_limits_selections. The existing SAR * power limit selection is unchanged if this attribute is not * present. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value * which specifies the number of SAR power limit specifications * which will follow. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power * limit specifications. The number of specifications is * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each * specification contains a set of * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A * specification is uniquely identified by the attributes * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always * contains as a payload the attribute * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT. * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is * needed based upon the value of * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to * indicate for which band this specification applies. Valid * values are enumerated in enum %nl80211_band (although not all * bands may be supported by a given device). If the attribute is * not supplied then the specification will be applied to all * supported bands. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value * to indicate for which antenna chain this specification * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the * attribute is not supplied then the specification will be * applied to all chains. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) * value to indicate for which modulation scheme this * specification applies. Valid values are enumerated in enum * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute * is not supplied then the specification will be applied to all * modulation schemes. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) * value to specify the actual power limit value in units of 0.5 * dBm (i.e., a value of 11 represents 5.5 dBm). * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. * * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. */ enum qca_vendor_attr_sar_limits { QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring * offload which is an extension for LL_STATS. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. * If MAC counters do not exceed the threshold, FW will report monitored * link layer counters periodically as this setting. The first report is * always triggered by this timer. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). * For each MAC layer counter, FW holds two copies. One is the current value. * The other is the last report. Once a current counter's increment is larger * than the threshold, FW will indicate that counter to host even if the * monitoring timer does not expire. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same * failure code. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code * 1: TX packet discarded * 2: No ACK * 3: Postpone * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. * Threshold for all monitored parameters. If per counter dedicated threshold * is not enabled, this threshold will take effect. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters * Bit0: TX counter unit in MSDU * Bit1: TX counter unit in MPDU * Bit2: TX counter unit in PPDU * Bit3: TX counter unit in byte * Bit4: Dropped MSDUs * Bit5: Dropped Bytes * Bit6: MPDU retry counter * Bit7: MPDU failure counter * Bit8: PPDU failure counter * Bit9: MPDU aggregation counter * Bit10: MCS counter for ACKed MPDUs * Bit11: MCS counter for Failed MPDUs * Bit12: TX Delay counter * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters * Bit0: MAC RX counter unit in MPDU * Bit1: MAC RX counter unit in byte * Bit2: PHY RX counter unit in PPDU * Bit3: PHY RX counter unit in byte * Bit4: Disorder counter * Bit5: Retry counter * Bit6: Duplication counter * Bit7: Discard counter * Bit8: MPDU aggregation size counter * Bit9: MCS counter * Bit10: Peer STA power state change (wake to sleep) counter * Bit11: Peer STA power save counter, total time in PS mode * Bit12: Probe request counter * Bit13: Other management frames counter * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA * Bit0: Idle time * Bit1: TX time * Bit2: time RX in current bss * Bit3: Out of current bss time * Bit4: Wireless medium busy time * Bit5: RX in bad condition time * Bit6: TX in bad condition time * Bit7: time wlan card not available * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal * Bit0: Per channel SNR counter * Bit1: Per channel noise floor counter * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: * aggregation stats buffer length * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats * buffer for ACKed MPDUs. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats * buffer for failed MPDUs. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: * length of delay stats array. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets * flagged as retransmissions * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets * flagged as duplicated * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX * packets discarded * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation * stats buffer. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs * stats buffer. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe * requests received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt * frames received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time * there is no TX, nor RX, nor interference. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time * transmitting packets. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time * for receiving. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time * interference detected. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time * receiving packets with errors. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time * TX no-ACK. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time * the chip is unable to work in normal conditions. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time * receiving packets in current BSS. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time * receiving packets not in current BSS. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: * This is a container for per antenna signal stats. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon */ enum qca_wlan_vendor_attr_ll_stats_ext { QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, /* Attributes for configurations */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, /* Peer STA power state change */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, /* TX failure event */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, /* MAC counters */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, /* Sub-attributes for PEER_AC_TX */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, /* Sub-attributes for PEER_AC_RX */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, /* Sub-attributes for CCA_BSS */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, /* sub-attribute for BSS_RX_TIME */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, /* Sub-attributes for PEER_SIGNAL */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, /* Sub-attributes for IFACE_BSS */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 }; /** * enum qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels * in priority order as decided after ACS operation in userspace. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON: Required (u8). * One of reason code from enum qca_wlan_vendor_acs_select_reason. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST: Required * Array of nested values for each channel with following attributes: * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST is deprecated and use * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST * is still used if either of the driver or user space application doesn't * support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY: Required (u8). * Primary channel number * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY is deprecated and use * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY * is still used if either of the driver or user space application doesn't * support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY: Required (u8). * Secondary channel number, required only for 160 and 80+80 MHz bandwidths. * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY is deprecated and use * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY * is still used if either of the driver or user space application * doesn't support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0: Required (u8). * VHT seg0 channel number * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 is deprecated and use * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 * is still used if either of the driver or user space application * doesn't support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1: Required (u8). * VHT seg1 channel number * Note: If both the driver and user-space application supports the 6 GHz band, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 is deprecated and use * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1. * To maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 * is still used if either of the driver or user space application * doesn't support the 6 GHz band. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH: Required (u8). * Takes one of enum nl80211_chan_width values. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST: Required * Array of nested values for each channel with following attributes: * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY in MHz (u32), * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY in MHz (u32), * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 in MHz (u32), * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 in MHz (u32), * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH * Note: If user-space application has no support of the 6 GHz band, this * attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY: Required (u32) * Primary channel frequency in MHz * Note: If user-space application has no support of the 6 GHz band, this * attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY: Required (u32) * Secondary channel frequency in MHz used for HT 40 MHz channels. * Note: If user-space application has no support of the 6 GHz band, this * attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0: Required (u32) * VHT seg0 channel frequency in MHz * Note: If user-space application has no support of the 6GHz band, this * attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1: Required (u32) * VHT seg1 channel frequency in MHz * Note: If user-space application has no support of the 6 GHz band, this * attribute is optional. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_PUNCTURE_BITMAP: Required (u16) * Puncture Bitmap for selected primary channel. Optional if no support * for EHT (IEEE 802.11be). Encoding for this attribute follows the * convention used in the Disabled Subchannel Bitmap field of the EHT Operation * element. */ enum qca_wlan_vendor_attr_external_acs_channels { QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, /* Array of nested values for each channel with following attributes: * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, /* This (u8) will hold values of one of enum nl80211_bands */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, /* Primary channel (u8) */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, /* Secondary channel (u8) used for HT 40 MHz channels */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, /* VHT seg0 channel (u8) */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, /* VHT seg1 channel (u8) */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, /* Channel width (u8). Takes one of enum nl80211_chan_width values. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST = 9, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY = 10, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY = 11, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 = 12, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 = 13, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_PUNCTURE_BITMAP = 14, /* keep last */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 }; /** * qca_wlan_vendor_acs_select_reason: This represents the different reasons why * the ACS has to be triggered. These values are used by * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON */ enum qca_wlan_vendor_acs_select_reason { /* Represents the reason that the ACS triggered during the AP start */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, /* Represents the reason that DFS found with the current channel */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, /* Represents the reason that LTE co-exist in the current band. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, /* Represents the reason that generic, uncategorized interference has * been found in the current channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_GENERIC_INTERFERENCE, /* Represents the reason that excessive 802.11 interference has been * found in the current channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_80211_INTERFERENCE, /* Represents the reason that generic Continuous Wave (CW) interference * has been found in the current channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_CW_INTERFERENCE, /* Represents the reason that Microwave Oven (MWO) interference has been * found in the current channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_MWO_INTERFERENCE, /* Represents the reason that generic Frequency-Hopping Spread Spectrum * (FHSS) interference has been found in the current channel. This may * include 802.11 waveforms. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_FHSS_INTERFERENCE, /* Represents the reason that non-802.11 generic Frequency-Hopping * Spread Spectrum (FHSS) interference has been found in the current * channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_FHSS_INTERFERENCE, /* Represents the reason that generic Wideband (WB) interference has * been found in the current channel. This may include 802.11 waveforms. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_WB_INTERFERENCE, /* Represents the reason that non-802.11 generic Wideband (WB) * interference has been found in the current channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_WB_INTERFERENCE, /* Represents the reason that Jammer interference has been found in the * current channel. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_JAMMER_INTERFERENCE, /* Represents the reason that ACS triggered by AFC */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_AFC_TRIGGER, }; /** * enum qca_wlan_gpio_attr - Parameters for GPIO configuration * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND: Required (u32) * value to specify the gpio command, please refer to enum qca_gpio_cmd_type * to get the available value that this item can use. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM: Required (u32) * value to specify the gpio number. * Required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG or %.QCA_WLAN_VENDOR_GPIO_OUTPUT. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE: Required (u32) * value to specify the gpio output level, please refer to enum qca_gpio_value * to get the available value that this item can use. * Required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_OUTPUT. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE: Optional (u32) * value to specify the gpio pull type, please refer to enum qca_gpio_pull_type * to get the available value that this item can use. * Required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG and * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG * attribute is present. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE: Optional (u32) * value to specify the gpio interrupt mode, please refer to enum * qca_gpio_interrupt_mode to get the available value that this item can use. * Required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG and * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG * attribute is present. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR: Optional (u32) * value to specify the gpio direction, please refer to enum qca_gpio_direction * to get the available value that this item can use. * Required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG and * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG * attribute is present. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG: Optional (u32) * Value to specify the mux config. Meaning of a given value is dependent * on the target chipset and gpio pin. Must be of the range 0-15. * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to 0. * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE: Optional (u32) * Value to specify the drive, Refer to enum qca_gpio_drive. * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to QCA_WLAN_GPIO_DRIVE_2MA(0). * * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG: Optional (flag) * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is * %QCA_WLAN_VENDOR_GPIO_CONFIG. When present this attribute signals that all * other parameters for the given GPIO will be obtained from internal * configuration. Only %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM must be * specified to indicate the GPIO pin being configured. */ enum qca_wlan_gpio_attr { QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, /* Unsigned 32-bit attribute for GPIO command */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND = 1, /* Unsigned 32-bit attribute for GPIO PIN number to configure */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM = 2, /* Unsigned 32-bit attribute for GPIO value to configure */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE = 3, /* Unsigned 32-bit attribute for GPIO pull type */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE = 4, /* Unsigned 32-bit attribute for GPIO interrupt mode */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE = 5, /* Unsigned 32-bit attribute for GPIO direction to configure */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR = 6, /* Unsigned 32-bit attribute for GPIO mux config */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG = 7, /* Unsigned 32-bit attribute for GPIO drive */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE = 8, /* Flag attribute for using internal gpio configuration */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG = 9, /* keep last */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1, }; /** * enum gpio_cmd_type - GPIO configuration command type * @QCA_WLAN_VENDOR_GPIO_CONFIG: set gpio configuration info * @QCA_WLAN_VENDOR_GPIO_OUTPUT: set gpio output level */ enum qca_gpio_cmd_type { QCA_WLAN_VENDOR_GPIO_CONFIG = 0, QCA_WLAN_VENDOR_GPIO_OUTPUT = 1, }; /** * enum qca_gpio_pull_type - GPIO pull type * @QCA_WLAN_GPIO_PULL_NONE: set gpio pull type to none * @QCA_WLAN_GPIO_PULL_UP: set gpio pull up * @QCA_WLAN_GPIO_PULL_DOWN: set gpio pull down */ enum qca_gpio_pull_type { QCA_WLAN_GPIO_PULL_NONE = 0, QCA_WLAN_GPIO_PULL_UP = 1, QCA_WLAN_GPIO_PULL_DOWN = 2, QCA_WLAN_GPIO_PULL_MAX, }; /** * enum qca_gpio_direction - GPIO direction * @QCA_WLAN_GPIO_INPUT: set gpio as input mode * @QCA_WLAN_GPIO_OUTPUT: set gpio as output mode * @QCA_WLAN_GPIO_VALUE_MAX: invalid value */ enum qca_gpio_direction { QCA_WLAN_GPIO_INPUT = 0, QCA_WLAN_GPIO_OUTPUT = 1, QCA_WLAN_GPIO_DIR_MAX, }; /** * enum qca_gpio_value - GPIO Value * @QCA_WLAN_GPIO_LEVEL_LOW: set gpio output level to low * @QCA_WLAN_GPIO_LEVEL_HIGH: set gpio output level to high * @QCA_WLAN_GPIO_LEVEL_MAX: invalid value */ enum qca_gpio_value { QCA_WLAN_GPIO_LEVEL_LOW = 0, QCA_WLAN_GPIO_LEVEL_HIGH = 1, QCA_WLAN_GPIO_LEVEL_MAX, }; /** * enum gpio_interrupt_mode - GPIO interrupt mode * @QCA_WLAN_GPIO_INTMODE_DISABLE: disable interrupt trigger * @QCA_WLAN_GPIO_INTMODE_RISING_EDGE: interrupt with gpio rising edge trigger * @QCA_WLAN_GPIO_INTMODE_FALLING_EDGE: interrupt with gpio falling edge trigger * @QCA_WLAN_GPIO_INTMODE_BOTH_EDGE: interrupt with gpio both edge trigger * @QCA_WLAN_GPIO_INTMODE_LEVEL_LOW: interrupt with gpio level low trigger * @QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH: interrupt with gpio level high trigger * @QCA_WLAN_GPIO_INTMODE_MAX: invalid value */ enum qca_gpio_interrupt_mode { QCA_WLAN_GPIO_INTMODE_DISABLE = 0, QCA_WLAN_GPIO_INTMODE_RISING_EDGE = 1, QCA_WLAN_GPIO_INTMODE_FALLING_EDGE = 2, QCA_WLAN_GPIO_INTMODE_BOTH_EDGE = 3, QCA_WLAN_GPIO_INTMODE_LEVEL_LOW = 4, QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH = 5, QCA_WLAN_GPIO_INTMODE_MAX, }; /** * enum gpio_drive - GPIO drive * @QCA_WLAN_GPIO_DRIVE_2MA: drive 2MA * @QCA_WLAN_GPIO_DRIVE_4MA: drive 4MA * @QCA_WLAN_GPIO_DRIVE_6MA: drive 6MA * @QCA_WLAN_GPIO_DRIVE_8MA: drive 8MA * @QCA_WLAN_GPIO_DRIVE_10MA: drive 10MA * @QCA_WLAN_GPIO_DRIVE_12MA: drive 12MA * @QCA_WLAN_GPIO_DRIVE_14MA: drive 14MA * @QCA_WLAN_GPIO_DRIVE_16MA: drive 16MA * @QCA_WLAN_GPIO_DRIVE_MAX: invalid gpio drive */ enum qca_gpio_drive { QCA_WLAN_GPIO_DRIVE_2MA = 0, QCA_WLAN_GPIO_DRIVE_4MA = 1, QCA_WLAN_GPIO_DRIVE_6MA = 2, QCA_WLAN_GPIO_DRIVE_8MA = 3, QCA_WLAN_GPIO_DRIVE_10MA = 4, QCA_WLAN_GPIO_DRIVE_12MA = 5, QCA_WLAN_GPIO_DRIVE_14MA = 6, QCA_WLAN_GPIO_DRIVE_16MA = 7, QCA_WLAN_GPIO_DRIVE_MAX, }; /** * qca_wlan_set_qdepth_thresh_attr - Parameters for setting * MSDUQ depth threshold per peer per tid in the target * * Associated Vendor Command: * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH */ enum qca_wlan_set_qdepth_thresh_attr { QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, /* 6-byte MAC address */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, /* Unsigned 32-bit attribute for holding the TID */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, /* Unsigned 32-bit attribute for holding the update mask * bit 0 - Update high priority msdu qdepth threshold * bit 1 - Update low priority msdu qdepth threshold * bit 2 - Update UDP msdu qdepth threshold * bit 3 - Update Non UDP msdu qdepth threshold * rest of bits are reserved */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, /* Unsigned 32-bit attribute for holding the threshold value */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, /* keep last */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, }; /** * qca_wlan_vendor_attr_external_acs_policy: Attribute values for * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the * external ACS policies to select the channels w.r.t. the PCL weights. * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and * their PCL weights.) * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to * select a channel with non-zero PCL weight. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a * channel with non-zero PCL weight. * */ enum qca_wlan_vendor_attr_external_acs_policy { QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, }; /** * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters */ enum qca_wlan_vendor_attr_spectral_scan { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, /* * Number of times the chip enters spectral scan mode before * deactivating spectral scans. When set to 0, chip will enter spectral * scan mode continuously. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, /* * Spectral scan period. Period increment resolution is 256*Tclk, * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, /* Spectral scan priority. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, /* Number of FFT data points to compute. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, /* * Enable targeted gain change before starting the spectral scan FFT. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, /* Restart a queued spectral scan. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, /* * Noise floor reference number for the calculation of bin power. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, /* * Disallow spectral scan triggers after TX/RX packets by setting * this delay value to roughly SIFS time period or greater. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, /* * Number of strong bins (inclusive) per sub-channel, below * which a signal is declared a narrow band tone. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, /* * Specify the threshold over which a bin is declared strong (for * scan bandwidth analysis). u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, /* Spectral scan report mode. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, /* * RSSI report mode, if the ADC RSSI is below * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, * then FFTs will not trigger, but timestamps and summaries get * reported. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, /* * ADC RSSI must be greater than or equal to this threshold (signed dB) * to ensure spectral scan reporting with normal error code. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, /* * Format of frequency bin magnitude for spectral scan triggered FFTs: * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, /* * Format of FFT report to software for spectral scan triggered FFTs. * 0: No FFT report (only spectral scan summary report) * 1: 2-dword summary of metrics for each completed FFT + spectral scan * report * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled * bins (in-band) per FFT + spectral scan summary report * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled * bins (all) per FFT + spectral scan summary report * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, /* * Number of LSBs to shift out in order to scale the FFT bins. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, /* * Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes * in dBm power. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, /* * Per chain enable mask to select input ADC for search FFT. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, /* * An unsigned 64-bit integer provided by host driver to identify the * spectral scan request. This attribute is included in the scan * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START * and used as an attribute in * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the * specific scan to be stopped. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, /* Skip interval for FFT reports. u32 attribute */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, /* Set to report only one set of FFT results. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, /* Debug level for spectral module in driver. * 0 : Verbosity level 0 * 1 : Verbosity level 1 * 2 : Verbosity level 2 * 3 : Matched filterID display * 4 : One time dump of FFT report * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, /* Type of spectral scan request. u32 attribute. * It uses values defined in enum * qca_wlan_vendor_attr_spectral_scan_request_type. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, /* This specifies the frequency span over which spectral * scan would be carried out. Its value depends on the * value of QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and * the relation is as follows. * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL * Not applicable. Spectral scan would happen in the * operating span. * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE * Center frequency (in MHz) of the span of interest or * for convenience, center frequency (in MHz) of any channel * in the span of interest. For 80+80 MHz agile spectral scan * request it represents center frequency (in MHz) of the primary * 80 MHz span or for convenience, center frequency (in MHz) of any * channel in the primary 80 MHz span. If agile spectral scan is * initiated without setting a valid frequency it returns the * error code * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED). * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY = 24, /* Spectral scan mode. u32 attribute. * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode. * If this attribute is not present, it is assumed to be * normal mode (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL). */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE = 25, /* Spectral scan error code. u32 attribute. * It uses values defined in enum * qca_wlan_vendor_spectral_scan_error_code. * This attribute is included only in failure scenarios. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE = 26, /* 8-bit unsigned value to enable/disable debug of the * Spectral DMA ring. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG = 27, /* 8-bit unsigned value to enable/disable debug of the * Spectral DMA buffers. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG = 28, /* This specifies the frequency span over which spectral scan would be * carried out. Its value depends on the value of * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and the relation is as * follows. * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL * Not applicable. Spectral scan would happen in the operating span. * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE * This attribute is applicable only for agile spectral scan * requests in 80+80 MHz mode. It represents center frequency (in * MHz) of the secondary 80 MHz span or for convenience, center * frequency (in MHz) of any channel in the secondary 80 MHz span. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2 = 29, /* This attribute specifies the bandwidth to be used for Spectral scan * operation. This is an u8 attribute and uses the values in enum * nl80211_chan_width. This is an optional attribute. * If this attribute is not populated, the driver should configure the * Spectral scan bandwidth to the maximum value supported by the target * for the current operating bandwidth. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BANDWIDTH = 30, /* Spectral FFT recapture flag attribute, to enable/disable FFT * recapture. Recapture can only be enabled for Scan period greater * than 52us. * If this attribute is enabled, re-triggers will be enabled in uCode * when AGC gain changes. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_RECAPTURE = 31, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. */ enum qca_wlan_vendor_attr_spectral_diag_stats { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, /* Number of spectral TLV signature mismatches. * u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, /* Number of spectral phyerror events with insufficient length when * parsing for secondary 80 search FFT report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, /* Number of spectral phyerror events without secondary 80 * search FFT report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, /* Number of spectral phyerror events with vht operation segment 1 id * mismatches in search fft report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, /* Number of spectral phyerror events with vht operation segment 2 id * mismatches in search fft report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. */ enum qca_wlan_vendor_attr_spectral_cap { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, /* Flag attribute to indicate phydiag capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, /* Flag attribute to indicate radar detection capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, /* Flag attribute to indicate spectral capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, /* Flag attribute to indicate advanced spectral capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, /* Spectral hardware generation. u32 attribute. * It uses values defined in enum * qca_wlan_vendor_spectral_scan_cap_hw_gen. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, /* Spectral bin scaling formula ID. u16 attribute. * It uses values defined in enum * qca_wlan_vendor_spectral_scan_cap_formula_id. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6, /* Spectral bin scaling param - low level offset. * s16 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7, /* Spectral bin scaling param - high level offset. * s16 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8, /* Spectral bin scaling param - RSSI threshold. * s16 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9, /* Spectral bin scaling param - default AGC max gain. * u8 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10, /* Flag attribute to indicate agile spectral scan capability * for 20/40/80 MHz modes. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL = 11, /* Flag attribute to indicate agile spectral scan capability * for 160 MHz mode. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_160 = 12, /* Flag attribute to indicate agile spectral scan capability * for 80+80 MHz mode. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_80_80 = 13, /* Number of spectral detectors used for scan in 20 MHz. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_20_MHZ = 14, /* Number of spectral detectors used for scan in 40 MHz. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_40_MHZ = 15, /* Number of spectral detectors used for scan in 80 MHz. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80_MHZ = 16, /* Number of spectral detectors used for scan in 160 MHz. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_160_MHZ = 17, /* Number of spectral detectors used for scan in 80+80 MHz. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80P80_MHZ = 18, /* Flag attribute to indicate agile spectral scan capability * for 320 MHz mode. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_320 = 19, /* Number of spectral detectors used for scan in 320 MHz. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_320_MHZ = 20, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. */ enum qca_wlan_vendor_attr_spectral_scan_status { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, /* Flag attribute to indicate whether spectral scan is enabled */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, /* Flag attribute to indicate whether spectral scan is in progress*/ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, /* Spectral scan mode. u32 attribute. * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode. * If this attribute is not present, normal mode * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL is assumed to be * requested. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE = 3, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_config_latency_level - Level for * wlan latency module. * * There will be various of Wi-Fi functionality like scan/roaming/adaptive * power saving which would causing data exchange out of service, this * would be a big impact on latency. For latency sensitive applications over * Wi-Fi are intolerant to such operations and thus would configure them * to meet their respective needs. It is well understood by such applications * that altering the default behavior would degrade the Wi-Fi functionality * w.r.t the above pointed WLAN operations. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: * Default WLAN operation level which throughput orientated. * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_XR: * Use XR level to benefit XR (extended reality) application to achieve * latency and power by via constraint scan/roaming/adaptive PS. * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: * Use low latency level to benefit application like concurrent * downloading or video streaming via constraint scan/adaptive PS. * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: * Use ultra low latency level to benefit for gaming/voice * application via constraint scan/roaming/adaptive PS. */ enum qca_wlan_vendor_attr_config_latency_level { QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_XR = 2, /* legacy name */ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_XR, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, }; /** * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the * spectral scan request types. * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to * set the spectral parameters and start scan. * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to * only set the spectral parameters. * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to * only start the spectral scan. */ enum qca_wlan_vendor_attr_spectral_scan_request_type { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, }; /** * qca_wlan_vendor_spectral_scan_mode: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE in the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START and * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE in the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. This represents the * spectral scan modes. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL: Normal spectral scan: * spectral scan in the current operating span. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE: Agile spectral scan: * spectral scan in the configured agile span. */ enum qca_wlan_vendor_spectral_scan_mode { QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL = 0, QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE = 1, }; /** * qca_wlan_vendor_spectral_scan_error_code: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE in the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED: Changing the value * of a parameter is not supported. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED: Requested spectral scan * mode is not supported. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE: A parameter * has invalid value. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED: A parameter * is not initialized. */ enum qca_wlan_vendor_spectral_scan_error_code { QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED = 0, QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED = 1, QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE = 2, QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED = 3, }; /** * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the * spectral hardware generation. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 */ enum qca_wlan_vendor_spectral_scan_cap_hw_gen { QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, }; /** * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the * Spectral bin scaling formula ID. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain * and RSSI threshold based formula. */ enum qca_wlan_vendor_spectral_scan_cap_formula_id { QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0, QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1, }; /** * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative * RF Operating Parameter (RROP) information is available, and if so, at which * point in the application-driver interaction sequence it can be retrieved by * the application from the driver. This point may vary by architecture and * other factors. This is a u16 value. */ enum qca_wlan_vendor_attr_rropavail_info { /* RROP information is unavailable. */ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, /* RROP information is available and the application can retrieve the * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS * event from the driver. */ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, /* RROP information is available only after a vendor specific scan * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has * successfully completed. The application can retrieve the information * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from * the driver. */ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, }; /** * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific * Representative RF Operating Parameter (RROP) information. It is sent for the * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is * intended for use by external Auto Channel Selection applications. It provides * guidance values for some RF parameters that are used by the system during * operation. These values could vary by channel, band, radio, and so on. */ enum qca_wlan_vendor_attr_rrop_info { QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, /* Representative Tx Power List (RTPL) which has an array of nested * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. */ QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list * entry instances in the Representative Tx Power List (RTPL). It provides * simplified power values intended for helping external Auto channel Selection * applications compare potential Tx power performance between channels, other * operating conditions remaining identical. These values are not necessarily * the actual Tx power values that will be used by the system. They are also not * necessarily the max or average values that will be used. Instead, they are * relative, summarized keys for algorithmic use computed by the driver or * underlying firmware considering a number of vendor specific factors. */ enum qca_wlan_vendor_attr_rtplinst { QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, /* Primary channel number (u8). * Note: If both the driver and user space application support the * 6 GHz band, this attribute is deprecated and * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY should be used. To * maintain backward compatibility, * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if either the * driver or user space application or both do not support the 6 GHz * band. */ QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, /* Representative Tx power in dBm (s32) with emphasis on throughput. */ QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, /* Representative Tx power in dBm (s32) with emphasis on range. */ QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, /* Primary channel center frequency (u32) in MHz */ QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY = 4, QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mac - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. * * @QCA_WLAN_VENDOR_ATTR_MAC_INFO: MAC mode info list which has an * array of nested values as per attributes in * enum qca_wlan_vendor_attr_mac_mode_info. */ enum qca_wlan_vendor_attr_mac { QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAC_MAX = QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected * WiFi netdev interface on a respective MAC. Used by the attribute * QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. * * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_ID: Wi-Fi Netdev's interface id(u32). * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ: Associated frequency in MHz of * the connected Wi-Fi interface(u32). */ enum qca_wlan_vendor_attr_mac_iface_info { QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. * * @QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID: Hardware MAC ID associated for the * MAC (u32) * @QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND: Band supported by the respective MAC * at a given point. This is a u32 bitmask of BIT(NL80211_BAND_*) as described * in enum nl80211_band. * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO: Refers to list of WLAN net dev * interfaces associated with this MAC. Represented by enum * qca_wlan_vendor_attr_mac_iface_info. */ enum qca_wlan_vendor_attr_mac_info { QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_thermal_stats - vendor subcmd attributes * to get thermal status from driver/firmware. * enum values are used for NL attributes encapsulated inside * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS nested attribute. * * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MIN_TEMPERATURE: Minimum temperature * of a thermal level in Celsius. u32 size. * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX_TEMPERATURE: Maximum temperature * of a thermal level in Celsius. u32 size. * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_DWELL_TIME: The total time spent on each * thermal level in milliseconds. u32 size. * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_TEMP_LEVEL_COUNTER: Indicates the number * of times the temperature crossed into the temperature range defined by the * thermal level from both higher and lower directions. u32 size. */ enum qca_wlan_vendor_attr_thermal_stats { QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MIN_TEMPERATURE, QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX_TEMPERATURE, QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_DWELL_TIME, QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_TEMP_LEVEL_COUNTER, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_AFTER_LAST - 1, }; /** * enum he_fragmentation_val - HE fragmentation support values * Indicates level of dynamic fragmentation that is supported by * a STA as a recipient. * HE fragmentation values are defined as per 11ax spec and are used in * HE capability IE to advertise the support. These values are validated * in the driver to check the device capability and advertised in the HE * capability element. * * @HE_FRAG_DISABLE: no support for dynamic fragmentation * @HE_FRAG_LEVEL1: support for dynamic fragments that are * contained within an MPDU or S-MPDU, no support for dynamic fragments * within an A-MPDU that is not an S-MPDU. * @HE_FRAG_LEVEL2: support for dynamic fragments that are * contained within an MPDU or S-MPDU and support for up to one dynamic * fragment for each MSDU, each A-MSDU if supported by the recipient, and * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an * MPDU or S-MPDU. * @HE_FRAG_LEVEL3: support for dynamic fragments that are * contained within an MPDU or S-MPDU and support for multiple dynamic * fragments for each MSDU and for each A-MSDU if supported by the * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. */ enum he_fragmentation_val { HE_FRAG_DISABLE, HE_FRAG_LEVEL1, HE_FRAG_LEVEL2, HE_FRAG_LEVEL3, }; /** * enum he_mcs_config - HE MCS support configuration * * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. * These values are used in driver to configure the HE MCS map to advertise * Tx/Rx MCS map in HE capability and these values are applied for all the * streams supported by the device. To configure MCS for different bandwidths, * vendor command needs to be sent using this attribute with appropriate value. * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS * attribute with QCA_WLAN_VENDOR_ATTR_HE_80_MCS0_7. And to configure HE MCS * for HE_160_MCS0_11 send this command using HE MCS config attribute with * value QCA_WLAN_VENDOR_ATTR_HE_160_MCS0_11; * * @HE_80_MCS0_7: support for HE 80/40/20MHz MCS 0 to 7 * @HE_80_MCS0_9: support for HE 80/40/20MHz MCS 0 to 9 * @HE_80_MCS0_11: support for HE 80/40/20MHz MCS 0 to 11 * @HE_160_MCS0_7: support for HE 160MHz MCS 0 to 7 * @HE_160_MCS0_9: support for HE 160MHz MCS 0 to 9 * @HE_160_MCS0_11: support for HE 160MHz MCS 0 to 11 * @HE_80p80_MCS0_7: support for HE 80p80MHz MCS 0 to 7 * @HE_80p80_MCS0_9: support for HE 80p80MHz MCS 0 to 9 * @HE_80p80_MCS0_11: support for HE 80p80MHz MCS 0 to 11 */ enum he_mcs_config { HE_80_MCS0_7 = 0, HE_80_MCS0_9 = 1, HE_80_MCS0_11 = 2, HE_160_MCS0_7 = 4, HE_160_MCS0_9 = 5, HE_160_MCS0_11 = 6, HE_80p80_MCS0_7 = 8, HE_80p80_MCS0_9 = 9, HE_80p80_MCS0_11 = 10, }; /** * enum qca_wlan_ba_session_config - BA session configuration * * Indicates the configuration values for BA session configuration attribute. * * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. */ enum qca_wlan_ba_session_config { QCA_WLAN_ADD_BA = 1, QCA_WLAN_DELETE_BA = 2, }; /** * enum qca_wlan_ac_type - access category type * * Indicates the access category type value. * * @QCA_WLAN_AC_BE: BE access category * @QCA_WLAN_AC_BK: BK access category * @QCA_WLAN_AC_VI: VI access category * @QCA_WLAN_AC_VO: VO access category * @QCA_WLAN_AC_ALL: All ACs */ enum qca_wlan_ac_type { QCA_WLAN_AC_BE = 0, QCA_WLAN_AC_BK = 1, QCA_WLAN_AC_VI = 2, QCA_WLAN_AC_VO = 3, QCA_WLAN_AC_ALL = 4, }; /** * enum qca_wlan_he_ltf_cfg - HE LTF configuration * * Indicates the HE LTF configuration value. * * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to * the mandatory HE-LTF based on the GI setting * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF */ enum qca_wlan_he_ltf_cfg { QCA_WLAN_HE_LTF_AUTO = 0, QCA_WLAN_HE_LTF_1X = 1, QCA_WLAN_HE_LTF_2X = 2, QCA_WLAN_HE_LTF_4X = 3, }; /** * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration * * Indicates the HE trigger frame MAC padding duration value. * * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to * process the trigger frame. * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for * trigger frame. * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for * trigger frame. */ enum qca_wlan_he_mac_padding_dur { QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, }; /** * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration * * Indicates the HE Operating mode control channel width setting value. * * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz */ enum qca_wlan_he_om_ctrl_ch_bw { QCA_WLAN_HE_OM_CTRL_BW_20M = 0, QCA_WLAN_HE_OM_CTRL_BW_40M = 1, QCA_WLAN_HE_OM_CTRL_BW_80M = 2, QCA_WLAN_HE_OM_CTRL_BW_160M = 3, }; /** * enum qca_wlan_keep_alive_data_type - Keep alive data type configuration * * Indicates the frame types to use for keep alive data. * * @QCA_WLAN_KEEP_ALIVE_DEFAULT: Driver default type used for keep alive. * @QCA_WLAN_KEEP_ALIVE_DATA: Data frame type for keep alive. * @QCA_WLAN_KEEP_ALIVE_MGMT: Management frame type for keep alive. */ enum qca_wlan_keep_alive_data_type { QCA_WLAN_KEEP_ALIVE_DEFAULT = 0, QCA_WLAN_KEEP_ALIVE_DATA = 1, QCA_WLAN_KEEP_ALIVE_MGMT = 2, }; /** * enum eht_mcs_config - EHT MCS support configuration * * Configures the EHT Tx/Rx MCS map in EHT Capability element. * These values are used in the driver to configure the EHT MCS map to advertise * Tx/Rx MCS map in EHT capability and these values are applied for all the * streams supported by the device. * @EHT_MCS0_7: EHT MCS 0 to 7 support * @EHT_MCS0_9: EHT MCS 0 to 9 support * @EHT_MCS0_11: EHT MCS 0 to 11 support * @EHT_MCS0_13: EHT MCS 0 to 13 support */ enum eht_mcs_config { EHT_MCS0_7 = 0, EHT_MCS0_9 = 1, EHT_MCS0_11 = 2, EHT_MCS0_13 = 3, }; /** * enum qca_wlan_eht_mlo_mode: EHT MLO mode configuration. * @QCA_WLAN_EHT_MODE_INVALID: Invalid. * @QCA_WLAN_EHT_MLSR: Multi-link single radio mode * @QCA_WLAN_EHT_EMLSR: Enhanced multi-link single radio mode. * @QCA_WLAN_EHT_NON_STR_MLMR: Non simultaneous transmit and receive * multi-link multi radio mode. * @QCA_WLAN_EHT_STR_MLMR: Simultaneous transmit and receive * multi-link multi radio mode. */ enum qca_wlan_eht_mlo_mode { QCA_WLAN_EHT_MODE_INVALID = 0, QCA_WLAN_EHT_MLSR = 1, QCA_WLAN_EHT_EMLSR = 2, QCA_WLAN_EHT_NON_STR_MLMR = 3, QCA_WLAN_EHT_STR_MLMR = 4, }; /** * enum qca_wlan_emlsr_mode: Enhanced Multi-link Single Radio mode configuration * @QCA_WLAN_EMLSR_MODE_ENTER: Enter EMLSR mode * @QCA_WLAN_EMLSR_MODE_EXIT: Exit EMLSR mode */ enum qca_wlan_emlsr_mode { QCA_WLAN_EMLSR_MODE_ENTER = 0, QCA_WLAN_EMLSR_MODE_EXIT = 1, }; /** * enum qca_wlan_ttlm_negotiation_support: TID-To-Link Mapping Negotiation * support * @QCA_WLAN_TTLM_DISABLE: TTLM disabled * @QCA_WLAN_TTLM_SAME_LINK_SET: Mapping of all TIDs to the same link set, * both DL and UL * @QCA_WLAN_TTLM_SAME_DIFF_LINK_SET: Mapping of each TID to the same or * different link set */ enum qca_wlan_ttlm_negotiation_support { QCA_WLAN_TTLM_DISABLE = 0, QCA_WLAN_TTLM_SAME_LINK_SET = 1, QCA_WLAN_TTLM_SAME_DIFF_LINK_SET = 2, }; /** * enum qca_coex_traffic_shaping_mode: Coex traffic shaping mode * @QCA_COEX_TRAFFIC_SHAPING_MODE_DISABLE: Coex policies disabled * @QCA_COEX_TRAFFIC_SHAPING_MODE_ENABLE: All coex policies enabled */ enum qca_coex_traffic_shaping_mode { QCA_COEX_TRAFFIC_SHAPING_MODE_DISABLE = 0, QCA_COEX_TRAFFIC_SHAPING_MODE_ENABLE = 1, }; /** * enum qca_wlan_vendor_attr_omi_tx: Represents attributes for HE and * EHT operating mode control transmit request. These attributes are * sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OMI_TX and * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. * * @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value * indicates the maximum number of spatial streams, NSS, that the STA * supports in reception for PPDU bandwidths less than or equal to 80 MHz * and is set to NSS - 1. * * @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value * indicates the operating channel width supported by the STA for both * reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values. * * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value * indicates the all trigger based UL MU operations by the STA. * 0 - UL MU operations are enabled by the STA. * 1 - All triggered UL MU transmissions are suspended by the STA. * * @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value * indicates the maximum number of space-time streams, NSTS, that * the STA supports in transmission and is set to NSTS - 1. * * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE: 8-bit unsigned value * combined with the UL MU Disable subfield and the recipient's setting * of the OM Control UL MU Data Disable RX Support subfield in the HE MAC * capabilities to determine which HE TB PPDUs are possible by the * STA to transmit. * 0 - UL MU data operations are enabled by the STA. * 1 - Determine which HE TB PPDU types are allowed by the STA if UL MU disable * bit is not set, else UL MU Tx is suspended. * * @QCA_WLAN_VENDOR_ATTR_EHT_OMI_RX_NSS_EXTN: 8-bit unsigned value in the EHT OM * Control subfield combined with the Rx NSS subfield in the OM Control subfield * indicates NSS - 1, where NSS is the maximum number of spatial streams that * STA supports in reception for PPDU bandwidths less than or equal to 80 MHz. * * @QCA_WLAN_VENDOR_ATTR_EHT_OMI_CH_BW_EXTN: 8-bit unsigned value indicates * 320 MHz operating channel width supported by the EHT STA for both reception * and transmission. * * @QCA_WLAN_VENDOR_ATTR_EHT_OMI_TX_NSS_EXTN: 8-bit unsigned value in the EHT OM * Control subfield combined with the Tx NSTS subfield in OM Control subfield * indicates NSTS - 1, where NSTS is the maximum number of space-time streams * that the STA supports in transmission for PPDU bandwidths less than or equal * to 80 MHz. */ enum qca_wlan_vendor_attr_omi_tx { QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0, QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1, QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2, QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3, QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4, QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE = 5, QCA_WLAN_VENDOR_ATTR_EHT_OMI_RX_NSS_EXTN = 6, QCA_WLAN_VENDOR_ATTR_EHT_OMI_CH_BW_EXTN = 7, QCA_WLAN_VENDOR_ATTR_EHT_OMI_TX_NSS_EXTN = 8, /* keep last */ QCA_WLAN_VENDOR_ATTR_OMI_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OMI_MAX = QCA_WLAN_VENDOR_ATTR_OMI_AFTER_LAST - 1, }; /* deprecated legacy names */ #define QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX \ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OMI_TX #define qca_wlan_vendor_attr_he_omi_tx \ qca_wlan_vendor_attr_omi_tx #define QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST \ QCA_WLAN_VENDOR_ATTR_OMI_AFTER_LAST #define QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX \ QCA_WLAN_VENDOR_ATTR_OMI_MAX /** * enum qca_wlan_vendor_phy_mode - Different PHY modes * These values are used with %QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE. * * @QCA_WLAN_VENDOR_PHY_MODE_AUTO: autoselect * @QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO: 2.4 GHz 802.11b/g/n/ax autoselect * @QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO: 5 GHz 802.11a/n/ac/ax autoselect * @QCA_WLAN_VENDOR_PHY_MODE_11A: 5 GHz, OFDM * @QCA_WLAN_VENDOR_PHY_MODE_11B: 2.4 GHz, CCK * @QCA_WLAN_VENDOR_PHY_MODE_11G: 2.4 GHz, OFDM * @QCA_WLAN_VENDOR_PHY_MODE_11AGN: Support 802.11n in both 2.4 GHz and 5 GHz * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20: 2.4 GHz, HT20 * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS: 2.4 GHz, HT40 (ext ch +1) * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS: 2.4 GHz, HT40 (ext ch -1) * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40: 2.4 GHz, Auto HT40 * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20: 5 GHz, HT20 * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS: 5 GHz, HT40 (ext ch +1) * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS: 5 GHz, HT40 (ext ch -1) * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40: 5 GHz, Auto HT40 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20: 5 GHz, VHT20 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS: 5 GHz, VHT40 (Ext ch +1) * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS: 5 GHz VHT40 (Ext ch -1) * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40: 5 GHz, VHT40 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80: 5 GHz, VHT80 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80: 5 GHz, VHT80+80 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160: 5 GHz, VHT160 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20: HE20 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40: HE40 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS: HE40 (ext ch +1) * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS: HE40 (ext ch -1) * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80: HE80 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80: HE 80P80 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160: HE160 */ enum qca_wlan_vendor_phy_mode { QCA_WLAN_VENDOR_PHY_MODE_AUTO = 0, QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO = 1, QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO = 2, QCA_WLAN_VENDOR_PHY_MODE_11A = 3, QCA_WLAN_VENDOR_PHY_MODE_11B = 4, QCA_WLAN_VENDOR_PHY_MODE_11G = 5, QCA_WLAN_VENDOR_PHY_MODE_11AGN = 6, QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20 = 7, QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS = 8, QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS = 9, QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40 = 10, QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20 = 11, QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS = 12, QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS = 13, QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40 = 14, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20 = 15, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS = 16, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS = 17, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40 = 18, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80 = 19, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80 = 20, QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160 = 21, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20 = 22, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40 = 23, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS = 24, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS = 25, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80 = 26, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80 = 27, QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160 = 28, }; /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION */ enum qca_wlan_vendor_attr_wifi_test_config { QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, /* 8-bit unsigned value to configure the driver to enable/disable * WMM feature. This attribute is used to configure testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, /* 8-bit unsigned value to configure the driver to accept/reject * the addba request from peer. This attribute is used to configure * the testbed device. * 1-accept addba, 0-reject addba */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, /* 8-bit unsigned value to configure the driver to send or not to * send the addba request to peer. * This attribute is used to configure the testbed device. * 1-send addba, 0-do not send addba */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, /* 8-bit unsigned value to indicate the HE fragmentation support. * Uses enum he_fragmentation_val values. * This attribute is used to configure the testbed device to * allow the advertised hardware capabilities to be downgraded * for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, /* 8-bit unsigned value to indicate the HE MCS support. * Uses enum he_mcs_config values. * This attribute is used to configure the testbed device to * allow the advertised hardware capabilities to be downgraded * for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, /* 8-bit unsigned value to configure the driver to allow or not to * allow the connection with WEP/TKIP in HT/VHT/HE modes. * This attribute is used to configure the testbed device. * 1-allow wep/tkip in HT/VHT/HE, 0-do not allow wep/tkip */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, /* 8-bit unsigned value to configure the driver to add a * new BA session or delete the existing BA session for * given TID. ADDBA command uses the buffer size and tid * configuration if user specifies the values else default * value for buffer size is used for all tids if the tid * also not specified. For DEL_BA command TID value is * required to process the command. * Uses enum qca_wlan_ba_session_config values. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, /* 16-bit unsigned value to configure the buffer size in addba * request and response frames. * This attribute is used to configure the testbed device. * The range of the value is 0 to 256. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, /* 8-bit unsigned value to configure the buffer size in addba * request and response frames. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, /* 8-bit unsigned value to configure the no ack policy. * To configure no ack policy, access category value * is required to process the command. * This attribute is used to configure the testbed device. * 1 - enable no ack, 0 - disable no ack */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, /* 8-bit unsigned value to configure the AC for no ack policy * This attribute is used to configure the testbed device. * uses the enum qca_wlan_ac_type values */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, /* 8-bit unsigned value to configure the HE LTF * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_he_ltf_cfg values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, /* 8-bit unsigned value to configure the tx beamformee. * This attribute is used to configure the testbed device. * 1 - enable, 0 - disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, /* 8-bit unsigned value to configure the tx beamformee number of * space-time streams. * This attribute is used to configure the testbed device. * The range of the value is 0 to 8 */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, /* 8-bit unsigned value to configure the MU EDCA params for given AC * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_ac_type values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC * To configure MU EDCA AIFSN value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, /* 8-bit unsigned value to configure the MU EDCA ECW min value for * given AC. * To configure MU EDCA ECW min value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, /* 8-bit unsigned value to configure the MU EDCA ECW max value for * given AC. * To configure MU EDCA ECW max value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, /* 8-bit unsigned value to configure the MU EDCA timer for given AC * To configure MU EDCA timer value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, /* 8-bit unsigned value to configure the HE trigger frame MAC padding * duration. * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_he_mac_padding_dur values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, /* 8-bit unsigned value to override the MU EDCA params to defaults * regardless of the AP beacon MU EDCA params. If it is enabled use * the default values else use the MU EDCA params from AP beacon. * This attribute is used to configure the testbed device. * 1 - enable override, 0 - disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, /* 8-bit unsigned value to configure the support for receiving * an MPDU that contains an operating mode control subfield. * This attribute is used to configure the testbed device. * 1-enable, 0-disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, /* Nested attribute values required to setup the TWT session. * enum qca_wlan_vendor_attr_twt_setup provides the necessary * information to set up the session. It contains broadcast flags, * set_up flags, trigger value, flow type, flow ID, wake interval * exponent, protection, target wake time, wake duration, wake interval * mantissa. These nested attributes are used to setup a host triggered * TWT session. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, /* This nested attribute is used to terminate the current TWT session. * It does not currently carry any attributes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, /* This nested attribute is used to suspend the current TWT session. * It does not currently carry any attributes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, /* Nested attribute values to indicate the request for resume. * This attribute is used to resume the TWT session. * enum qca_wlan_vendor_attr_twt_resume provides the necessary * parameters required to resume the TWT session. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, /* 8-bit unsigned value to set the HE operating mode control * (OM CTRL) Channel Width subfield. * The Channel Width subfield indicates the operating channel width * supported by the STA for both reception and transmission. * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. * This setting is cleared with the * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG * flag attribute to reset defaults. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, /* 8-bit unsigned value to configure the number of spatial * streams in HE operating mode control field. * This setting is cleared with the * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG * flag attribute to reset defaults. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, /* Flag attribute to configure the UL MU disable bit in * HE operating mode control field. * This setting is cleared with the * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG * flag attribute to reset defaults. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, /* Flag attribute to clear the previously set HE operating mode * control field configuration. * This attribute is used to configure the testbed device to reset * defaults to clear any previously set HE operating mode control * field configuration. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, /* 8-bit unsigned value to configure HE single user PPDU * transmission. By default this setting is disabled and it * is disabled in the reset defaults of the device configuration. * This attribute is used to configure the testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, /* 8-bit unsigned value to configure action frame transmission * in HE trigger based PPDU transmission. * By default this setting is disabled and it is disabled in * the reset defaults of the device configuration. * This attribute is used to configure the testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, /* Nested attribute to indicate HE operating mode control field * transmission. It contains operating mode control field Nss, * channel bandwidth, Tx Nsts and UL MU disable attributes. * These nested attributes are used to send HE operating mode control * with configured values. * Uses the enum qca_wlan_vendor_attr_omi_tx attributes. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OMI_TX = 33, /* 8-bit unsigned value to configure +HTC_HE support to indicate the * support for the reception of a frame that carries an HE variant * HT Control field. * This attribute is used to configure the testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34, /* 8-bit unsigned value to configure VHT support in 2.4G band. * This attribute is used to configure the testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_2G_VHT = 35, /* 8-bit unsigned value to configure HE testbed defaults. * This attribute is used to configure the testbed device. * 1-set the device HE capabilities to testbed defaults. * 0-reset the device HE capabilities to supported config. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_HE_TESTBED_DEFAULTS = 36, /* 8-bit unsigned value to configure twt request support. * This attribute is used to configure the testbed device. * 1-enable, 0-disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TWT_REQ_SUPPORT = 37, /* 8-bit unsigned value to configure protection for Management * frames when PMF is enabled for the association. * This attribute is used to configure the testbed device. * 0-use the correct key, 1-use an incorrect key, 2-disable protection. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PMF_PROTECTION = 38, /* Flag attribute to inject Disassociation frame to the connected AP. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISASSOC_TX = 39, /* 8-bit unsigned value to configure an override for the RSNXE Used * subfield in the MIC control field of the FTE in FT Reassociation * Request frame. * 0 - Default behavior, 1 - override with 1, 2 - override with 0. * This attribute is used to configure the testbed device. * This attribute can be configured when STA is in disconnected or * associated state and the configuration is valid until the next * disconnection. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FT_REASSOCREQ_RSNXE_USED = 40, /* 8-bit unsigned value to configure the driver to ignore CSA (Channel * Switch Announcement) when STA is in connected state. * 0 - Default behavior, 1 - Ignore CSA. * This attribute is used to configure the testbed device. * This attribute can be configured when STA is in disconnected or * associated state and the configuration is valid until the next * disconnection. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_CSA = 41, /* Nested attribute values required to configure OCI (Operating Channel * Information). Attributes defined in enum * qca_wlan_vendor_attr_oci_override are nested within this attribute. * This attribute is used to configure the testbed device. * This attribute can be configured when STA is in disconnected or * associated state and the configuration is valid until the next * disconnection. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE = 42, /* 8-bit unsigned value to configure the driver/firmware to ignore SA * Query timeout. If this configuration is enabled STA shall not send * Deauthentication frmae when SA Query times out (mainly, after a * channel switch when OCV is enabled). * 0 - Default behavior, 1 - Ignore SA Query timeout. * This attribute is used to configure the testbed device. * This attribute can be configured only when STA is in associated state * and the configuration is valid until the disconnection. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_SA_QUERY_TIMEOUT = 43, /* 8-bit unsigned value to configure the driver/firmware to start or * stop transmitting FILS discovery frames. * 0 - Stop transmitting FILS discovery frames * 1 - Start transmitting FILS discovery frames * This attribute is used to configure the testbed device. * This attribute can be configured only in AP mode and the * configuration is valid until AP restart. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FILS_DISCOVERY_FRAMES_TX = 44, /* 8-bit unsigned value to configure the driver/firmware to enable or * disable full bandwidth UL MU-MIMO subfield in the HE PHY capabilities * information field. * 0 - Disable full bandwidth UL MU-MIMO subfield * 1 - Enable full bandwidth UL MU-MIMO subfield * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO = 45, /* 16-bit unsigned value to configure the driver with a specific BSS * max idle period to advertise in the BSS Max Idle Period element * (IEEE Std 802.11-2016, 9.4.2.79) in (Re)Association Request frames. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BSS_MAX_IDLE_PERIOD = 46, /* 8-bit unsigned value to configure the driver to use only RU 242 tone * for data transmission. * 0 - Default behavior, 1 - Configure RU 242 tone for data Tx. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_RU_242_TONE_TX = 47, /* 8-bit unsigned value to configure the driver to disable data and * management response frame transmission to test the BSS max idle * feature. * 0 - Default behavior, 1 - Disable data and management response Tx. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISABLE_DATA_MGMT_RSP_TX = 48, /* 8-bit unsigned value to configure the driver/firmware to enable or * disable Punctured Preamble Rx subfield in the HE PHY capabilities * information field. * 0 - Disable Punctured Preamble Rx subfield * 1 - Enable Punctured Preamble Rx subfield * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PUNCTURED_PREAMBLE_RX = 49, /* 8-bit unsigned value to configure the driver to ignore the SAE H2E * requirement mismatch for 6 GHz connection. * 0 - Default behavior, 1 - Ignore SAE H2E requirement mismatch. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_H2E_RSNXE = 50, /* 8-bit unsigned value to configure the driver to allow 6 GHz * connection with all security modes. * 0 - Default behavior, 1 - Allow 6 GHz connection with all security * modes. * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_6GHZ_SECURITY_TEST_MODE = 51, /* 8-bit unsigned value to configure the driver to transmit data with * ER SU PPDU type. * * 0 - Default behavior, 1 - Enable ER SU PPDU type TX. * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ER_SU_PPDU_TYPE = 52, /* 8-bit unsigned value to configure the driver to use Data or * Management frame type for keep alive data. * Uses enum qca_wlan_keep_alive_data_type values. * * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_KEEP_ALIVE_FRAME_TYPE = 53, /* 8-bit unsigned value to configure the driver to use scan request * BSSID value in Probe Request frame RA(A1) during the scan. The * driver saves this configuration and applies this setting to all user * space scan requests until the setting is cleared. If this * configuration is set, the driver uses the BSSID value from the scan * request to set the RA(A1) in the Probe Request frames during the * scan. * * 0 - Default behavior uses the broadcast RA in Probe Request frames. * 1 - Uses the scan request BSSID in RA in Probe Request frames. * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_USE_BSSID_IN_PROBE_REQ_RA = 54, /* 8-bit unsigned value to configure the driver to enable/disable the * BSS max idle period support. * * 0 - Disable the BSS max idle support. * 1 - Enable the BSS max idle support. * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BSS_MAX_IDLE_PERIOD_ENABLE = 55, /* 8-bit unsigned value to configure the driver/firmware to enable or * disable Rx control frame to MultiBSS subfield in the HE MAC * capabilities information field. * 0 - Disable Rx control frame to MultiBSS subfield * 1 - Enable Rx control frame to MultiBSS subfield * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_RX_CTRL_FRAME_TO_MBSS = 56, /* 8-bit unsigned value to configure the driver/firmware to enable or * disable Broadcast TWT support subfield in the HE MAC capabilities * information field. * 0 - Disable Broadcast TWT support subfield * 1 - Enable Broadcast TWT support subfield * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BCAST_TWT_SUPPORT = 57, /* 8-bit unsigned value to configure the driver/firmware to allow eMLSR * mode for 802.11be MLO capable devices. If the attribute is set to 1, * and if the FW supports this capability too, then the STA host * advertises this capability to AP over assoc request frame. This * attribute will not have any effect on legacy devices with no 802.11be * support. * 0 - Default behavior * 1 - Enable eMLSR (Enhanced Multi-link Single-Radio) mode * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_11BE_EMLSR_MODE = 58, /* 8-bit unsigned value to configure the driver to enable/disable the * periodic sounding for Tx beamformer functionality. The default * behavior uses algorithm to do sounding based on packet stats. * * 0 - Default behavior. * 1 - Enable the periodic sounding for Tx beamformer. * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BEAMFORMER_PERIODIC_SOUNDING = 59, /* 8-bit unsigned value to configure beamformee SS EHT capability * to indicate the maximum number of spatial streams that the STA * can receive in an EHT sounding NDP for <= 80 MHz bandwidth. * The range of the value is 3 to 7. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_BEAMFORMEE_SS_80MHZ = 60, /* 8-bit unsigned value to configure beamformee SS EHT capability * to indicate the maximum number of spatial streams that the STA * can receive in an EHT sounding NDP for 160 MHz bandwidth. * The range of the value is 3 to 7. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_BEAMFORMEE_SS_160MHZ = 61, /* 8-bit unsigned value to configure beamformee SS EHT capability * to indicate the maximum number of spatial streams that the STA * can receive in an EHT sounding NDP for 320 MHz bandwidth. * The range of the value is 3 to 7. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_BEAMFORMEE_SS_320MHZ = 62, /* 8-bit unsigned value to configure the driver to exclude station * profile in Probe Request frame Multi-Link element. * 0 - Default behavior, sends the Probe Request frame with station * profile data included in the Multi-Link element. * 1 - Exclude station profile in Probe Request frame Multi-Link * element. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EXCLUDE_STA_PROF_IN_PROBE_REQ = 63, /* 8-bit unsigned value to configure EHT testbed defaults. * This attribute is used to configure the testbed device. * 1 - Set the device EHT capabilities to testbed defaults. * 0 - Reset the device EHT capabilities to supported config. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_EHT_TESTBED_DEFAULTS = 64, /* 8-bit unsigned value to indicate the EHT MCS support. * Uses enum eht_mcs_config values. * This attribute is used to configure the testbed device to * allow the advertised hardware capabilities to be downgraded * for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_MCS = 65, /* 8-bit unsigned value to configure EHT TB Sounding Feedback * Rate Limit capability. * This attribute is used to configure the testbed device. * 0 - Indicates no maximum supported data rate limitation. * 1 - Indicates the maximum supported data rate is the lower of * the 1500 Mb/s and the maximum supported data rate. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_TB_SOUNDING_FB_RL = 66, /* 8-bit unsigned value to configure the support for receiving an MPDU * that contains an EHT operating mode control subfield. * This attribute is used to configure the testbed device. * 1-enable, 0-disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_OM_CTRL_SUPPORT = 67, /* 8-bit unsigned value to configure the driver with EMLSR padding delay * subfield value. * * 0 - 0 us * 1 - 32 us * 2 - 64 us * 3 - 128 us * 4 - 256 us * 5-255 - Reserved * * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EMLSR_PADDING_DELAY = 68, /* * 8-bit unsigned value to indicate the firmware to force the active MLO * links to power save mode for the configured number of beacon periods. * This allows the firmware to suspend STA links for X beacon periods * and remain asleep even if the AP advertises TIM as opposed to regular * power save mode where STA links wake up if the AP indicates that it * has buffered data to send. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FORCE_MLO_POWER_SAVE_BCN_PERIOD = 69, /* * 8-bit unsigned value to indicate the firmware to be in STR MLMR mode * to enable simultaneous transmission of PPDUs on all active links. * 0 - Default behavior * 1 - Enter STR mode for simultaneous data transmission on all links */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_MLO_STR_TX = 70, /* Nested attribute to indicate EHT MLO links on which powersave to be * enabled. It contains link ID attributes. These nested attributes are * of the type u8 and are used to enable the powersave on associated * MLO links corresponding to the link IDs provided in the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_MLO_LINK_POWER_SAVE = 71, /* 8-bit unsigned value to configure the MLD ID of the BSS whose link * info is requested in the ML Probe Request frame. In the MLO-MBSSID * testcase, STA can request information of non-Tx BSS through Tx BSS * by configuring non-Tx BSS MLD ID within the ML probe request that * is transmitted via host initiated scan request. * * This attribute is used for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MLD_ID_ML_PROBE_REQ = 72, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_twt_operation - Operation of the config TWT request * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION. * The response for the respective operations can be either synchronous or * asynchronous (wherever specified). If synchronous, the response to this * operation is obtained in the corresponding vendor command reply to the user * space. For the asynchronous case the response is obtained as an event with * the same operation type. * * Drivers shall support either of these modes but not both simultaneously. * This support for asynchronous mode is advertised through the flag * QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If this flag is not advertised, * the driver shall support synchronous mode. * * @QCA_WLAN_TWT_SET: Setup a TWT session. Required parameters are configured * through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum * qca_wlan_vendor_attr_twt_setup. Depending upon the * @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, this is either a * synchronous or asynchronous operation. * * @QCA_WLAN_TWT_GET: Get the configured TWT parameters. Required parameters are * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum * qca_wlan_vendor_attr_twt_setup. This is a synchronous operation. * * @QCA_WLAN_TWT_TERMINATE: Terminate the TWT session. Required parameters are * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup. * This terminate can either get triggered by the user space or can as well be * a notification from the firmware if it initiates a terminate. * Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, * the request from user space can either be a synchronous or asynchronous * operation. * * @QCA_WLAN_TWT_SUSPEND: Suspend the TWT session. Required parameters are * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup. * Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, * this is either a synchronous or asynchronous operation. * * @QCA_WLAN_TWT_RESUME: Resume the TWT session. Required parameters are * configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum * qca_wlan_vendor_attr_twt_resume. Valid only after the TWT session is setup. * This can as well be a notification from the firmware on a QCA_WLAN_TWT_NUDGE * request. * request. Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT * capability, this is either a synchronous or asynchronous operation. * * @QCA_WLAN_TWT_NUDGE: Suspend and resume the TWT session. TWT nudge is a * combination of suspend and resume in a single request. Required parameters * are configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the * enum qca_wlan_vendor_attr_twt_nudge. Valid only after the TWT session is * setup. Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT * capability, this is either a synchronous or asynchronous operation. * * @QCA_WLAN_TWT_GET_STATS: Get the TWT session traffic statistics information. * Refers the enum qca_wlan_vendor_attr_twt_stats. Valid only after the TWT * session is setup. It's a synchronous operation. * * @QCA_WLAN_TWT_CLEAR_STATS: Clear TWT session traffic statistics information. * Valid only after the TWT session is setup. It's a synchronous operation. * * @QCA_WLAN_TWT_GET_CAPABILITIES: Get TWT capabilities of this device and its * peer. Refers the enum qca_wlan_vendor_attr_twt_capability. It's a synchronous * operation. * * @QCA_WLAN_TWT_SETUP_READY_NOTIFY: Notify userspace that the firmware is * ready for a new TWT session setup after it issued a twt teardown. * * @QCA_WLAN_TWT_SET_PARAM: Configure TWT related parameters. Required * parameters are obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refer * the enum qca_wlan_vendor_attr_twt_set_param. * * @QCA_WLAN_TWT_NOTIFY: Used to notify userspace about changes in TWT * related information for example TWT required bit in AP capabilities etc. * The reason for the notification is sent using * QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_NOTIFY_STATUS. */ enum qca_wlan_twt_operation { QCA_WLAN_TWT_SET = 0, QCA_WLAN_TWT_GET = 1, QCA_WLAN_TWT_TERMINATE = 2, QCA_WLAN_TWT_SUSPEND = 3, QCA_WLAN_TWT_RESUME = 4, QCA_WLAN_TWT_NUDGE = 5, QCA_WLAN_TWT_GET_STATS = 6, QCA_WLAN_TWT_CLEAR_STATS = 7, QCA_WLAN_TWT_GET_CAPABILITIES = 8, QCA_WLAN_TWT_SETUP_READY_NOTIFY = 9, QCA_WLAN_TWT_SET_PARAM = 10, QCA_WLAN_TWT_NOTIFY = 11, }; /* enum qca_wlan_vendor_attr_config_twt: Defines attributes used by * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION: * u8 attribute. Specify the TWT operation of this request. Possible values * are defined in enum qca_wlan_twt_operation. The parameters for the * respective operation is specified through * QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS: Nested attribute representing the * parameters configured for TWT. These parameters are represented by * enum qca_wlan_vendor_attr_twt_setup, enum qca_wlan_vendor_attr_twt_resume, * enum qca_wlan_vendor_attr_twt_set_param or * enum qca_wlan_vendor_attr_twt_stats based on the operation. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_NOTIFY_STATUS: Size is u8, mandatory when * QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION is set to QCA_WLAN_TWT_NOTIFY. * The values used by this attribute are defined in * enum qca_wlan_vendor_twt_status. */ enum qca_wlan_vendor_attr_config_twt { QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION = 1, QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS = 2, QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_NOTIFY_STATUS = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_MAX = QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST - 1, }; /** * qca_wlan_twt_setup_state: Represents the TWT session states. * * QCA_WLAN_TWT_SETUP_STATE_NOT_ESTABLISHED: TWT session not established. * QCA_WLAN_TWT_SETUP_STATE_ACTIVE: TWT session is active. * QCA_WLAN_TWT_SETUP_STATE_SUSPEND: TWT session is in suspended state. */ enum qca_wlan_twt_setup_state { QCA_WLAN_TWT_SETUP_STATE_NOT_ESTABLISHED = 0, QCA_WLAN_TWT_SETUP_STATE_ACTIVE = 1, QCA_WLAN_TWT_SETUP_STATE_SUSPEND = 2, }; /** * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for * TWT (Target Wake Time) setup request. These attributes are sent as part of * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. * Disable (flag attribute not present) - Individual TWT * Enable (flag attribute present) - Broadcast TWT. * Individual means the session is between the STA and the AP. * This session is established using a separate negotiation between * STA and AP. * Broadcast means the session is across multiple STAs and an AP. The * configuration parameters are announced in Beacon frames by the AP. * This is used in * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to * specify the TWT request type. This is used in TWT SET operation. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute * Enable (flag attribute present) - TWT with trigger support. * Disable (flag attribute not present) - TWT without trigger support. * Trigger means the AP will send the trigger frame to allow STA to send data. * Without trigger, the STA will wait for the MU EDCA timer before * transmitting the data. * This is used in * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) * 0 - Announced TWT - In this mode, STA may skip few service periods to * save more power. If STA wants to wake up, it will send a PS-POLL/QoS * NULL frame to AP. * 1 - Unannounced TWT - The STA will wakeup during every SP. * This is a required parameter for * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) * Flow ID is the unique identifier for each TWT session. * If not provided then dialog ID will be set to zero. * This is an optional parameter for * 1. TWT SET Request and Response * 2. TWT GET Request and Response * 3. TWT TERMINATE Request and Response * 4. TWT SUSPEND Request and Response * Flow Id values from 0 to 254 represent a single TWT session * Flow ID value of 255 represents all twt sessions for the following * 1. TWT TERMINATE Request and Response * 2. TWT SUSPEND Request and Response * 4. TWT CLEAR STATISTICS request * 5. TWT GET STATISTICS request and response * If an invalid dialog id is provided, status * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) * This attribute (exp) is used along with the mantissa to derive the * wake interval using the following formula: * pow(2,exp) = wake_intvl_us/wake_intvl_mantis * Wake interval is the interval between 2 successive SP. * This is a required parameter for * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute * Enable (flag attribute present) - Protection required. * Disable (flag attribute not present) - Protection not required. * If protection is enabled, then the AP will use protection * mechanism using RTS/CTS to self to reserve the airtime. * This is used in * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) * This attribute is used as the SP offset which is the offset from * TSF after which the wake happens. The units are in microseconds. If * this attribute is not provided, then the value will be set to zero. * This is an optional parameter for * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) * This is the duration of the service period. This is specified as * multiples of 256 microseconds. Valid values are 0x1 to 0xFF. * This is a required parameter for * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) * This attribute is used to configure wake interval mantissa. * The units are in TU. * This is a required parameter for * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS: Required (u8) * This field is applicable for TWT response only. * This contains status values in enum qca_wlan_vendor_twt_status * and is passed to the userspace. This is used in TWT SET operation. * This is a required parameter for * 1. TWT SET Response * 2. TWT TERMINATE Response * 3. TWT SUSPEND Response * 4. TWT RESUME Response * 5. TWT NUDGE Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE: Required (u8) * This field is applicable for TWT response only. * This field contains response type from the TWT responder and is * passed to the userspace. The values for this field are defined in * enum qca_wlan_vendor_twt_setup_resp_type. This is used in TWT SET * response. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF: Required (u64) * In TWT setup command this field contains absolute TSF that will * be used by TWT requester during setup. * In TWT response this field contains absolute TSF value of the * wake time received from the TWT responder and is passed to * the userspace. * This is an optional parameter for * 1. TWT SET Request * This is a required parameter for * 1. TWT SET Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED: Flag attribute. * Enable (flag attribute present) - Indicates that the TWT responder * supports reception of TWT information frame from the TWT requestor. * Disable (flag attribute not present) - Indicates that the responder * doesn't support reception of TWT information frame from requestor. * This is used in * 1. TWT SET Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR: 6-byte MAC address * Represents the MAC address of the peer for which the TWT session * is being configured. This is used in AP mode to represent the respective * client * In AP mode, this is a required parameter in response for * 1. TWT SET * 2. TWT GET * 3. TWT TERMINATE * 4. TWT SUSPEND * In STA mode, this is an optional parameter in request and response for * the above four TWT operations. * In AP mode, this is a required parameter in request for * 1. TWT GET * 2. TWT TERMINATE * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_INTVL: Optional (u32) * Minimum tolerance limit of wake interval parameter in microseconds. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_INTVL: Optional (u32) * Maximum tolerance limit of wake interval parameter in microseconds. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_DURATION: Optional (u32) * Minimum tolerance limit of wake duration parameter in microseconds. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_DURATION: Optional (u32) * Maximum tolerance limit of wake duration parameter in microseconds. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATE: Optional (u32) * TWT state for the given dialog id. The values for this are represented * by enum qca_wlan_twt_setup_state. * This is obtained through TWT GET operation. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA: Optional (u32) * This attribute is used to configure wake interval mantissa. * The unit is microseconds. This attribute, when specified, takes * precedence over QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA. * This parameter is used for * 1. TWT SET Request and Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_ID: Optional (u8) * This attribute is used to configure Broadcast TWT ID. * The Broadcast TWT ID indicates a specific Broadcast TWT for which the * transmitting STA is providing TWT parameters. The allowed values are 0 to 31. * This parameter is used for * 1. TWT SET Request * 2. TWT TERMINATE Request * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_RECOMMENDATION: Optional (u8) * This attribute is used to configure Broadcast TWT recommendation. * The Broadcast TWT Recommendation subfield contains a value that indicates * recommendations on the types of frames that are transmitted by TWT * scheduled STAs and scheduling AP during the broadcast TWT SP. * The allowed values are 0 - 3. * This parameter is used for * 1. TWT SET Request * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_PERSISTENCE: Optional (u8) * This attribute is used to configure Broadcast TWT Persistence. * The Broadcast TWT Persistence subfield indicates the number of * TBTTs during which the Broadcast TWT SPs corresponding to this * broadcast TWT Parameter set are present. The number of beacon intervals * during which the Broadcast TWT SPs are present is equal to the value in the * Broadcast TWT Persistence subfield plus 1 except that the value 255 * indicates that the Broadcast TWT SPs are present until explicitly terminated. * This parameter is used for * 1. TWT SET Request * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE: Optional (u8) * This attribute contains the value of the Responder PM Mode subfield (0 or 1) * from TWT response frame. * This parameter is used for * 1. TWT SET Response * 2. TWT GET Response * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_ANNOUNCE_TIMEOUT: Optional (u32) * This attribute is used to configure the announce timeout value (in us) in * firmware. This timeout value is only applicable for announced TWT. If * timeout value is non-zero then firmware waits upto timeout value to use * data frame as announcement frame. If timeout value is 0 then firmware sends * explicit QoS NULL frame as announcement frame on SP start. Default value in * firmware is 0. * This parameter is used for * 1. TWT SET Request */ enum qca_wlan_vendor_attr_twt_setup { QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, /* TWT Response only attributes */ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS = 11, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE = 12, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF = 13, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED = 14, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR = 15, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_INTVL = 16, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_INTVL = 17, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_DURATION = 18, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_DURATION = 19, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATE = 20, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA = 21, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_ID = 22, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_RECOMMENDATION = 23, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_PERSISTENCE = 24, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE = 25, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_ANNOUNCE_TIMEOUT = 26, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_twt_status - Represents the status of the requested * TWT operation * * @QCA_WLAN_VENDOR_TWT_STATUS_OK: TWT request successfully completed * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED: TWT not enabled * @QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID: TWT dialog ID is already used * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY: TWT session is busy * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST: TWT session does not exist * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED: TWT session not in suspend state * @QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM: Invalid parameters * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY: FW not ready * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE: FW resource exhausted * @QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK: Peer AP/STA did not ACK the * request/response frame * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE: Peer AP did not send the response * frame * @QCA_WLAN_VENDOR_TWT_STATUS_DENIED: AP did not accept the request * @QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR: Adding TWT dialog failed due to an * unknown reason * @QCA_WLAN_VENDOR_TWT_STATUS_ALREADY_SUSPENDED: TWT session already in * suspend state * @QCA_WLAN_VENDOR_TWT_STATUS_IE_INVALID: FW has dropped the frame due to * invalid IE in the received TWT frame * @QCA_WLAN_VENDOR_TWT_STATUS_PARAMS_NOT_IN_RANGE: Parameters received from * the responder are not in the specified range * @QCA_WLAN_VENDOR_TWT_STATUS_PEER_INITIATED_TERMINATE: FW terminated the TWT * session due to request from the responder. Used on the TWT_TERMINATE * notification from the firmware. * @QCA_WLAN_VENDOR_TWT_STATUS_ROAM_INITIATED_TERMINATE: FW terminated the TWT * session due to roaming. Used on the TWT_TERMINATE notification from the * firmware. * @QCA_WLAN_VENDOR_TWT_STATUS_SCC_MCC_CONCURRENCY_TERMINATE: FW terminated the * TWT session due to SCC (Single Channel Concurrency) and MCC (Multi Channel) * Concurrency). Used on the TWT_TERMINATE notification from the firmware. * @QCA_WLAN_VENDOR_TWT_STATUS_ROAMING_IN_PROGRESS: FW rejected the TWT setup * request due to roaming in progress. * @QCA_WLAN_VENDOR_TWT_STATUS_CHANNEL_SWITCH_IN_PROGRESS: FW rejected the TWT * setup request due to channel switch in progress. * @QCA_WLAN_VENDOR_TWT_STATUS_SCAN_IN_PROGRESS: FW rejected the TWT setup * request due to scan in progress. * QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE: The driver requested to * terminate an existing TWT session on power save exit request from userspace. * Used on the TWT_TERMINATE notification from the driver/firmware. * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_REQUIRED: The peer has set the TWT * required bit in its capabilities. * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_REQUIRED: The peer has cleared * the TWT required bit(1->0) in its capabilities. */ enum qca_wlan_vendor_twt_status { QCA_WLAN_VENDOR_TWT_STATUS_OK = 0, QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED = 1, QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID = 2, QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY = 3, QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST = 4, QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED = 5, QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM = 6, QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY = 7, QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE = 8, QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK = 9, QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE = 10, QCA_WLAN_VENDOR_TWT_STATUS_DENIED = 11, QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR = 12, QCA_WLAN_VENDOR_TWT_STATUS_ALREADY_SUSPENDED = 13, QCA_WLAN_VENDOR_TWT_STATUS_IE_INVALID = 14, QCA_WLAN_VENDOR_TWT_STATUS_PARAMS_NOT_IN_RANGE = 15, QCA_WLAN_VENDOR_TWT_STATUS_PEER_INITIATED_TERMINATE = 16, QCA_WLAN_VENDOR_TWT_STATUS_ROAM_INITIATED_TERMINATE = 17, QCA_WLAN_VENDOR_TWT_STATUS_SCC_MCC_CONCURRENCY_TERMINATE = 18, QCA_WLAN_VENDOR_TWT_STATUS_ROAMING_IN_PROGRESS = 19, QCA_WLAN_VENDOR_TWT_STATUS_CHANNEL_SWITCH_IN_PROGRESS = 20, QCA_WLAN_VENDOR_TWT_STATUS_SCAN_IN_PROGRESS = 21, QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE = 22, QCA_WLAN_VENDOR_TWT_STATUS_TWT_REQUIRED = 23, QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_REQUIRED = 24, }; /** * enum qca_wlan_vendor_attr_twt_resume - Represents attributes for * TWT (Target Wake Time) resume request. These attributes are sent as part of * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. * * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT: Optional (u32) * These attributes are used as the SP offset which is the offset from TSF after * which the wake happens. The units are in microseconds. Please note that * _NEXT_TWT is limited to u8 whereas _NEXT2_TWT takes the u32 data. * _NEXT2_TWT takes the precedence over _NEXT_TWT and thus the recommendation * is to use _NEXT2_TWT. If neither of these attributes is provided, the value * will be set to zero. * * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) * This attribute represents the next TWT subfield size. * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits, * and 4 for 64 bits. * * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID: Required (u8). * Flow ID is the unique identifier for each TWT session. This attribute * represents the respective TWT session to resume. * Flow Id values from 0 to 254 represent a single TWT session * Flow ID value of 255 represents all TWT sessions. * If an invalid dialog id is provided, status * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. * * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR: 6-byte MAC address * Represents the MAC address of the peer to which TWT Resume is * being sent. This is used in AP mode to represent the respective * client and is a required parameter. In STA mode, this is an optional * parameter * */ enum qca_wlan_vendor_attr_twt_resume { QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID = 3, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT = 4, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_twt_nudge - Represents attributes for * TWT (Target Wake Time) nudge request. TWT nudge is a combination of suspend * and resume in a single request. These attributes are sent as part of * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID: Required (u8) * Flow ID is the unique identifier for each TWT session. This attribute * represents the respective TWT session to suspend and resume. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID: Required (u8) * Flow ID is the unique identifier for each TWT session. This attribute * represents the respective TWT session to suspend and resume. * Flow Id values from 0 to 254 represent a single TWT session * Flow ID value of 255 represents all TWT sessions in TWT NUDGE request * and response. * If an invalid dialog id is provided, status * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME: Required (u32) * This attribute is used as the SP offset which is the offset from * TSF after which the wake happens. The units are in microseconds. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_NEXT_TWT_SIZE: Required (u32) * This attribute represents the next TWT subfield size. * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits, * and 4 for 64 bits. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAC_ADDR: 6-byte MAC address * Represents the MAC address of the peer to which TWT Suspend and Resume is * being sent. This is used in AP mode to represent the respective * client and is a required parameter. In STA mode, this is an optional * parameter. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME_TSF: Optional (u64) * This field contains absolute TSF value of the time at which twt * sesion will be resumed. * * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_SP_START_OFFSET: Optional (s32) * This field will be used when device supports Flexible TWT. * This field contains an offset value by which to shift the starting time * of the next service period. The value of offset can be negative or positive. * If provided, this attribute will override * QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME. The units are in microseconds. */ enum qca_wlan_vendor_attr_twt_nudge { QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID = 1, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME = 2, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_NEXT_TWT_SIZE = 3, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAC_ADDR = 4, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME_TSF = 5, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_SP_START_OFFSET = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAX = QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_twt_stats: Represents attributes for * TWT (Target Wake Time) get statistics and clear statistics request. * These attributes are sent as part of * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_FLOW_ID: Required (u8) * Flow ID is the unique identifier for each TWT session. This attribute * represents the respective TWT session for get and clear TWT statistics. * Flow Id values from 0 to 254 represent a single TWT session * Flow ID value of 255 represents all TWT sessions in * 1) TWT GET STATISTICS request and response * 2) TWT CLEAR STATISTICS request * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAC_ADDR: 6-byte MAC address * Represents the MAC address of the peer for which TWT Statistics * is required. * In AP mode this is used to represent the respective * client and is a required parameter for * 1) TWT GET STATISTICS request and response * 2) TWT CLEAR STATISTICS request and response * In STA mode, this is an optional parameter. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_SESSION_WAKE_DURATION: Required (u32) * This is the duration of the service period in microseconds. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVG_WAKE_DURATION: Required (u32) * Average of actual wake duration observed so far. Unit is microseconds. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS: Required (u32) * Number of TWT service period elapsed so far. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION: Required (u32) * This is the minimum value of wake duration observed across * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. Unit is * microseconds. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION: Required (u32) * This is the maximum value of wake duration observed across * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. Unit is * microseconds. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_MPDU: Required (u32) * Average number of MPDU's transmitted successfully across * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_MPDU: Required (u32) * Average number of MPDU's received successfully across * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_PACKET_SIZE: Required (u32) * Average number of bytes transmitted successfully across * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_PACKET SIZE: Required (u32) * Average number of bytes received successfully across * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. * * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS: Required (u32) * Status of the TWT GET STATISTICS request. * This contains status values in enum qca_wlan_vendor_twt_status * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. */ enum qca_wlan_vendor_attr_twt_stats { QCA_WLAN_VENDOR_ATTR_TWT_STATS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_STATS_FLOW_ID = 1, QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAC_ADDR = 2, QCA_WLAN_VENDOR_ATTR_TWT_STATS_SESSION_WAKE_DURATION = 3, QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVG_WAKE_DURATION = 4, QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS = 5, QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION = 6, QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX_WAKE_DURATION = 7, QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_MPDU = 8, QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_MPDU = 9, QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_PACKET_SIZE = 10, QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_PACKET_SIZE = 11, QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS = 12, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX = QCA_WLAN_VENDOR_ATTR_TWT_STATS_AFTER_LAST - 1, }; /** * qca_wlan_twt_get_capa - Represents the Bitmap of TWT capabilities * supported by the device and peer. * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_GET_CAPABILITIES * * @QCA_WLAN_TWT_CAPA_REQUESTOR: TWT requestor support is advertised by * TWT non-scheduling STA. This capability is advertised in the HE * capability/Extended capabilities information element in the * Association request frame by the device. * * @QCA_WLAN_TWT_CAPA_RESPONDER: TWT responder support is advertised * by the TWT scheduling AP. This capability is advertised in the extended * capabilities/HE capabilities information element. * * @QCA_WLAN_TWT_CAPA_BROADCAST: On requestor side, this indicates support * for the broadcast TWT functionality. On responder side, this indicates * support for the role of broadcast TWT scheduling functionality. This * capability is advertised in the HE capabilities information element. * * @QCA_WLAN_TWT_CAPA_TWT_FLEXIBLE: Device supports flexible TWT schedule. * This capability is advertised in the HE capabilities information element. * * @QCA_WLAN_TWT_CAPA_REQUIRED: The TWT Required is advertised by AP to indicate * that it mandates the associated HE STAs to support TWT. This capability is * advertised by AP in the HE Operation Parameters field of the HE operation * information element. */ enum qca_wlan_twt_capa { QCA_WLAN_TWT_CAPA_REQUESTOR = BIT(0), QCA_WLAN_TWT_CAPA_RESPONDER = BIT(1), QCA_WLAN_TWT_CAPA_BROADCAST = BIT(2), QCA_WLAN_TWT_CAPA_FLEXIBLE = BIT(3), QCA_WLAN_TWT_CAPA_REQUIRED = BIT(4), }; /** * enum qca_wlan_vendor_attr_twt_capability - Represents attributes for TWT * get capabilities request type. Used by QCA_WLAN_TWT_GET_CAPABILITIES TWT * operation. * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAC_ADDR: 6-byte MAC address * Represents the MAC address of the peer for which the TWT capabilities * are being queried. This is used in AP mode to represent the respective * client. In STA mode, this is an optional parameter. * * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_SELF: (u16). * Self TWT capabilities. Carries a bitmap of TWT capabilities specified in * enum qca_wlan_twt_capa. * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_PEER: (u16). * Peer TWT capabilities. Carries a bitmap of TWT capabilities specified in * enum qca_wlan_twt_capa. */ enum qca_wlan_vendor_attr_twt_capability { QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_SELF = 2, QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_PEER = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAX = QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_twt_set_param: Represents attributes for * TWT (Target Wake Time) related parameters. It is used when * %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION is set to %QCA_WLAN_TWT_SET_PARAM. * These attributes are sent as part of %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. * * @QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE: Optional (u8) * This attribute configures AC parameters to be used for all TWT * sessions in AP mode. * Uses the enum qca_wlan_ac_type values. */ enum qca_wlan_vendor_attr_twt_set_param { QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_twt_setup_resp_type - Represents the response type by * the TWT responder * * @QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE: TWT responder suggests TWT * parameters that are different from TWT requesting STA suggested * or demanded TWT parameters * @QCA_WLAN_VENDOR_TWT_RESP_DICTATE: TWT responder demands TWT * parameters that are different from TWT requesting STA TWT suggested * or demanded parameters * @QCA_WLAN_VENDOR_TWT_RESP_REJECT: TWT responder rejects TWT * setup * @QCA_WLAN_VENDOR_TWT_RESP_ACCEPT: TWT responder accepts the TWT * setup. */ enum qca_wlan_vendor_twt_setup_resp_type { QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE = 1, QCA_WLAN_VENDOR_TWT_RESP_DICTATE = 2, QCA_WLAN_VENDOR_TWT_RESP_REJECT = 3, QCA_WLAN_VENDOR_TWT_RESP_ACCEPT = 4, }; /** * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) * Represents the setup type being requested for TWT. * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT * parameters but relying on AP to fill the parameters during the negotiation. * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested * values which the AP may accept or AP may provide alternative parameters * which the STA may accept. * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any * alternate parameters than the requested ones. */ enum qca_wlan_vendor_twt_setup_req_type { QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, }; /** * enum qca_wlan_throughput_level - Current throughput level * * Indicates the current level of throughput calculated by driver. The driver * may choose different thresholds to decide whether the throughput level is * low or medium or high based on variety of parameters like physical link * capacity of current connection, number of pakcets being dispatched per * second etc. The throughput level events might not be consistent with the * actual current throughput value being observed. * * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput */ enum qca_wlan_throughput_level { QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, }; /** * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to * report throughput changes from driver to user space. enum values are used * for NL attributes sent with * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. */ enum qca_wlan_vendor_attr_throughput_change { QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, /* * Indicates the direction of throughput in which the change is being * reported. u8 attribute. Value is 0 for TX and 1 for RX. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, /* * Indicates the newly observed throughput level. * qca_wlan_throughput_level describes the possible range of values. * u8 attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, /* * Indicates the driver's guidance on the new value to be set to * kernel's tcp parameter tcp_limit_output_bytes. u32 attribute. Driver * may optionally include this attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, /* * Indicates the driver's guidance on the new value to be set to * kernel's tcp parameter tcp_adv_win_scale. s8 attribute. Possible * values are from -31 to 31. Driver may optionally include this * attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, /* * Indicates the driver's guidance on the new value to be set to * kernel's tcp parameter tcp_delack_seg. u32 attribute. Driver may * optionally include this attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, }; /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. */ enum qca_wlan_nan_ext_subcmd_type { /* Subcmd of type NAN Enable Request */ QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, /* Subcmd of type NAN Disable Request */ QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, }; /** * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. */ enum qca_wlan_vendor_attr_nan_params { QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, /* Carries NAN command for firmware component. Every vendor command * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a * payload containing the NAN command. NLA_BINARY attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, /* Indicates the type of NAN command sent with * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type * describes the possible range of values. This attribute is mandatory * if the command being issued is either * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz * band. This attribute is mandatory when command type is * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz * band. This attribute is optional and should be included when command * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_cfr_data_transport_modes - Defines QCA vendor CFR data * transport modes and is used by attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE as part of vendor command * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. * @QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS: Use RELAY FS to send CFR data. * @QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS: Use netlink events to send CFR * data. The data shall be encapsulated within * QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA along with vendor sub command * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG as an asynchronous event. */ enum qca_wlan_vendor_cfr_data_transport_modes { QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS = 0, QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS = 1, }; /** * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. * @QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL: CFR method using QOS Null frame. * @QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE: CFR method using QOS Null frame * with phase * @QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE: CFR method using probe response frame */ enum qca_wlan_vendor_cfr_method { QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0, QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE = 1, QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE = 2, }; /** * enum qca_wlan_vendor_cfr_capture_type - QCA vendor CFR capture type used by * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE. * @QCA_WLAN_VENDOR_CFR_DIRECT_FTM: Filter directed FTM ACK frames. * @QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK: Filter all FTM ACK frames. * @QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP: Filter NDPA NDP directed frames. * @QCA_WLAN_VENDOR_CFR_TA_RA: Filter frames based on TA/RA/Subtype which * is provided by one or more of below attributes: * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER * @QCA_WLAN_CFR_ALL_PACKET: Filter all packets. * @QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL: Filter all NDPA NDP frames. */ enum qca_wlan_vendor_cfr_capture_type { QCA_WLAN_VENDOR_CFR_DIRECT_FTM = 0, QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK = 1, QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP = 2, QCA_WLAN_VENDOR_CFR_TA_RA = 3, QCA_WLAN_VENDOR_CFR_ALL_PACKET = 4, QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL = 5, }; /** * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer * Channel Frequency Response capture parameters and enable periodic CFR * capture. * * @QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR: Optional (6-byte MAC address) * MAC address of peer. This is for CFR version 1 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE: Required (flag) * Enable peer CFR Capture. This attribute is mandatory to * enable peer CFR capture. If this attribute is not present, * peer CFR capture is disabled. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH: Optional (u8) * BW of measurement, attribute uses the values in enum nl80211_chan_width * Supported values: 20, 40, 80, 80+80, 160. * Note that all targets may not support all bandwidths. * This attribute is mandatory for version 1 if attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY: Optional (u32) * Periodicity of CFR measurement in msec. * Periodicity should be a multiple of Base timer. * Current Base timer value supported is 10 msecs (default). * 0 for one shot capture. * This attribute is mandatory for version 1 if attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD: Optional (u8) * Method used to capture Channel Frequency Response. * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method. * This attribute is mandatory for version 1 if attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. * * @QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE: Optional (flag) * Enable periodic CFR capture. * This attribute is mandatory for version 1 to enable Periodic CFR capture. * If this attribute is not present, periodic CFR capture is disabled. * * @QCA_WLAN_VENDOR_ATTR_CFR_VERSION: Optional (u8) * Value is 1 or 2 since there are two versions of CFR capture. Two versions * can't be enabled at same time. This attribute is mandatory if target * support both versions and use one of them. * * @QCA_WLAN_VENDOR_ATTR_CFR_ENABLE_GROUP_BITMAP: Optional (u32) * This attribute is mandatory for version 2 if * QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY is used. * Bits 15:0 Bit fields indicating which group to be enabled. * Bits 31:16 Reserved for future use. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION: Optional (u32) * CFR capture duration in microsecond. This attribute is mandatory for * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL is used. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL: Optional (u32) * CFR capture interval in microsecond. This attribute is mandatory for * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION is used. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE: Optional (u32) * CFR capture type is defined in enum qca_wlan_vendor_cfr_capture_type. * This attribute is mandatory for version 2. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK: Optional (u64) * Bit fields indicating which user in the current UL MU * transmissions are enabled for CFR capture. Bits 36 to 0 indicating * user indexes for 37 users in a UL MU transmission. If bit 0 is set, * then the CFR capture will happen for user index 0 in the current * UL MU transmission. If bits 0,2 are set, then CFR capture for UL MU * TX corresponds to user indices 0 and 2. Bits 63:37 Reserved for future use. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT: Optional (u32) * Indicates the number of consecutive Rx packets to be skipped * before CFR capture is enabled again. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE: Nested attribute containing * one or more %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY attributes. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY: Nested attribute containing * the following GROUP attributes: * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER, * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER: Optional (u32) * Target support multiple groups for some configurations. Group number could be * any value between 0 and 15. This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA: Optional (6-byte MAC address) * Transmitter address which is used to filter packets, this MAC address takes * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA: Optional (6-byte MAC address) * Receiver address which is used to filter packets, this MAC address takes * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK: Optional (6-byte MAC address) * Mask of transmitter address which is used to filter packets. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK: Optional (6-byte MAC address) * Mask of receiver address which is used to filter packets. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS: Optional (u32) * Indicates packets with a specific NSS will be filtered for CFR capture. * This is for CFR version 2 only. This is a bitmask. Bits 7:0, CFR capture will * be done for packets matching the NSS specified within this bitmask. * Bits 31:8 Reserved for future use. Bits 7:0 map to NSS: * bit 0 : NSS 1 * bit 1 : NSS 2 * ... * bit 7 : NSS 8 * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW: Optional (u32) * Indicates packets with a specific BW will be filtered for CFR capture. * This is for CFR version 2 only. This is a bitmask. Bits 4:0, CFR capture * will be done for packets matching the bandwidths specified within this * bitmask. Bits 31:5 Reserved for future use. Bits 4:0 map to bandwidth * numerated in enum nl80211_band (although not all bands may be supported * by a given device). * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER: Optional (u32) * Management packets matching the subtype filter categories will be * filtered in by MAC for CFR capture. This is a bitmask, in which each bit * represents the corresponding mgmt subtype value as per * IEEE 802.11(2016) 9.2.4.1.3 Type and Subtype subfields. * For example, beacon frame control type is 8, its value is 1<<8 = 0x100. * This is for CFR version 2 only * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER: Optional (u32) * Control packets matching the subtype filter categories will be * filtered in by MAC for CFR capture. This is a bitmask, in which each bit * represents the corresponding control subtype value as per * IEEE 802.11(2016) 9.2.4.1.3 Type and Subtype subfields. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER: Optional (u32) * Data packets matching the subtype filter categories will be * filtered in by MAC for CFR capture. This is a bitmask, in which each bit * represents the corresponding data subtype value as per * IEEE 802.11(2016) 9.2.4.1.3 Type and Subtype subfields. * This is for CFR version 2 only. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE: Optional (u8) * Userspace can use this attribute to specify the driver about which transport * mode shall be used by the driver to send CFR data to userspace. Uses values * from enum qca_wlan_vendor_cfr_data_transport_modes. When this attribute is * not present, driver shall choose the default transport mechanism which is * QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID: Optional (u32) * Userspace can use this attribute to specify the nl port id of the application * which receives the CFR data and processes it further so that the drivers can * unicast the NL events to a specific application. Optionally included when * QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE is set to * QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS, not required otherwise. The drivers * shall multicast the netlink events when this attribute is not included. * * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA: Required (NLA_BINARY). * This attribute will be used by the driver to encapsulate and send CFR data * to userspace along with QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG as an * asynchronous event when the driver is configured to send CFR data using NL * events with %QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS * */ enum qca_wlan_vendor_peer_cfr_capture_attr { QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2, QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3, QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4, QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5, QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6, QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION = 7, QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP = 8, QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION = 9, QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL = 10, QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE = 11, QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK = 12, QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT = 13, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE = 14, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY = 15, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER = 16, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA = 17, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA = 18, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK = 19, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK = 20, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS = 21, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW = 22, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER = 23, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER = 24, QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER = 25, QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE = 26, QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID = 27, QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA = 28, /* Keep last */ QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX = QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1, }; /** * enum qca_coex_config_profiles - This enum defines different types of * traffic streams that can be prioritized one over the other during coex * scenarios. * The types defined in this enum are categorized in the below manner. * 0 - 31 values corresponds to WLAN * 32 - 63 values corresponds to BT * 64 - 95 values corresponds to Zigbee * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP * @QCA_BT_A2DP: Prioritize BT A2DP * @QCA_BT_BLE: Prioritize BT BLE * @QCA_BT_SCO: Prioritize BT SCO * @QCA_ZB_LOW: Prioritize Zigbee Low * @QCA_ZB_HIGH: Prioritize Zigbee High */ enum qca_coex_config_profiles { /* 0 - 31 corresponds to WLAN */ QCA_WIFI_STA_DISCOVERY = 0, QCA_WIFI_STA_CONNECTION = 1, QCA_WIFI_STA_CLASS_3_MGMT = 2, QCA_WIFI_STA_DATA = 3, QCA_WIFI_STA_ALL = 4, QCA_WIFI_SAP_DISCOVERY = 5, QCA_WIFI_SAP_CONNECTION = 6, QCA_WIFI_SAP_CLASS_3_MGMT = 7, QCA_WIFI_SAP_DATA = 8, QCA_WIFI_SAP_ALL = 9, QCA_WIFI_CASE_MAX = 31, /* 32 - 63 corresponds to BT */ QCA_BT_A2DP = 32, QCA_BT_BLE = 33, QCA_BT_SCO = 34, QCA_BT_CASE_MAX = 63, /* 64 - 95 corresponds to Zigbee */ QCA_ZB_LOW = 64, QCA_ZB_HIGH = 65, QCA_ZB_CASE_MAX = 95, /* 0xff is default value if the u8 profile value is not set. */ QCA_PROFILE_DEFAULT_VALUE = 255 }; /** * enum qca_vendor_attr_coex_config_types - Coex configurations types. * This enum defines the valid set of values of coex configuration types. These * values may used by attribute * %QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE. * * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET: Reset all the * weights to default values. * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START: Start to config * weights with configurability value. */ enum qca_vendor_attr_coex_config_types { QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET = 1, QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START = 2, QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_TYPE_MAX }; /** * enum qca_vendor_attr_coex_config_three_way - Specifies vendor coex config * attributes * Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG * * QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE: u32 attribute. * Indicate config type. * the config types are 32-bit values from qca_vendor_attr_coex_config_types * * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1: u32 attribute. * Indicate the Priority 1 profiles. * the profiles are 8-bit values from enum qca_coex_config_profiles * In same priority level, maximum to 4 profiles can be set here. * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2: u32 attribute. * Indicate the Priority 2 profiles. * the profiles are 8-bit values from enum qca_coex_config_profiles * In same priority level, maximum to 4 profiles can be set here. * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3: u32 attribute. * Indicate the Priority 3 profiles. * the profiles are 8-bit values from enum qca_coex_config_profiles * In same priority level, maximum to 4 profiles can be set here. * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4: u32 attribute. * Indicate the Priority 4 profiles. * the profiles are 8-bit values from enum qca_coex_config_profiles * In same priority level, maximum to 4 profiles can be set here. * NOTE: * limitations for QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_x priority * arrangement: * 1: In the same u32 attribute(priority x), the profiles enum values own * same priority level. * 2: 0xff is default value if the u8 profile value is not set. * 3: max to 4 rules/profiles in same priority level. * 4: max to 4 priority level (priority 1 - priority 4) * 5: one priority level only supports one scenario from WLAN/BT/ZB, * hybrid rules not support. * 6: if WMI_COEX_CONFIG_THREE_WAY_COEX_RESET called, priority x will * remain blank to reset all parameters. * For example: * * If the attributes as follow: * priority 1: * ------------------------------------ * | 0xff | 0 | 1 | 2 | * ------------------------------------ * priority 2: * ------------------------------------- * | 0xff | 0xff | 0xff | 32 | * ------------------------------------- * priority 3: * ------------------------------------- * | 0xff | 0xff | 0xff | 65 | * ------------------------------------- * then it means: * 1: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION * owns same priority level. * 2: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION * has priority over BT_A2DP and ZB_HIGH. * 3: BT_A2DP has priority over ZB_HIGH. */ enum qca_vendor_attr_coex_config_three_way { QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_INVALID = 0, QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE = 1, QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1 = 2, QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2 = 3, QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3 = 4, QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4 = 5, /* Keep last */ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST, QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_MAX = QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST - 1, }; /** * enum qca_vendor_attr_peer_stats_cache_type - Represents peer stats cache type * This enum defines the valid set of values of peer stats cache types. These * values are used by attribute * %QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE_INVALID. * * @QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS: Represents peer tx rate statistics. * @QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS: Represents peer rx rate statistics. * @QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS: Represents peer tx sojourn * statistics */ enum qca_vendor_attr_peer_stats_cache_type { QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS, QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS, QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS, }; /** * enum qca_wlan_vendor_attr_peer_stats_cache_params - This enum defines * attributes required for QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH * Attributes are required to flush peer rate statistics from driver to * user application. * * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE: Unsigned 32-bit attribute * Indicate peer stats cache type. * The statistics types are 32-bit values from * qca_vendor_attr_peer_stats_cache_type * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC: Unsigned 8-bit array * of size 6, representing peer mac address. * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA: Opaque data attribute * containing buffer of statistics to send event to application layer entity. * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE: Unsigned 64-bit attribute * representing cookie for peer unique session. */ enum qca_wlan_vendor_attr_peer_stats_cache_params { QCA_WLAN_VENDOR_ATTR_PEER_STATS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE = 1, QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC = 2, QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA = 3, QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE = 4, /* Keep last */ QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST, QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_MAX = QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST - 1 }; /** * enum qca_mpta_helper_attr_zigbee_state - current states of zegbee. * this enum defines all the possible state of zigbee, which can be * delivered by NetLink attribute QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE. * * @ZIGBEE_IDLE: zigbee in idle state * @ZIGBEE_FORM_NETWORK: zibee forming network * @ZIGBEE_WAIT_JOIN: zigbee waiting for joining network * @ZIGBEE_JOIN: zigbee joining network * @ZIGBEE_NETWORK_UP: zigbee network is up * @ZIGBEE_HMI: zigbee in HMI mode */ enum qca_mpta_helper_attr_zigbee_state { ZIGBEE_IDLE = 0, ZIGBEE_FORM_NETWORK = 1, ZIGBEE_WAIT_JOIN = 2, ZIGBEE_JOIN = 3, ZIGBEE_NETWORK_UP = 4, ZIGBEE_HMI = 5, }; /** * enum qca_mpta_helper_vendor_attr - used for NL attributes sent by * vendor sub-command QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG. */ enum qca_mpta_helper_vendor_attr { QCA_MPTA_HELPER_VENDOR_ATTR_INVALID = 0, /* Optional attribute used to update zigbee state. * enum qca_mpta_helper_attr_zigbee_state. * NLA_U32 attribute. */ QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE = 1, /* Optional attribute used to configure wlan duration for Shape-OCS * during interrupt. * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION. * Value range 0 ~ 300 (ms). * NLA_U32 attribute. */ QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION = 2, /* Optional attribute used to configure non wlan duration for Shape-OCS * during interrupt. * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION. * Value range 0 ~ 300 (ms). * NLA_U32 attribute. */ QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION = 3, /* Optional attribute used to configure wlan duration for Shape-OCS * monitor period. * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION. * Value range 0 ~ 300 (ms) * NLA_U32 attribute */ QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION = 4, /* Optional attribute used to configure non wlan duration for Shape-OCS * monitor period. * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION. * Value range 0 ~ 300 (ms) * NLA_U32 attribute */ QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION = 5, /* Optional attribute used to configure ocs interrupt duration. * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION. * Value range 1000 ~ 20000 (ms) * NLA_U32 attribute */ QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION = 6, /* Optional attribute used to configure ocs monitor duration. * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION. * Value range 1000 ~ 20000 (ms) * NLA_U32 attribute */ QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION = 7, /* Optional attribute used to notify wlan FW current zigbee channel. * Value range 11 ~ 26 * NLA_U32 attribute */ QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_CHAN = 8, /* Optional attribute used to configure wlan mute duration. * Value range 0 ~ 400 (ms) * NLA_U32 attribute */ QCA_MPTA_HELPER_VENDOR_ATTR_WLAN_MUTE_DURATION = 9, /* keep last */ QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST, QCA_MPTA_HELPER_VENDOR_ATTR_MAX = QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_beacon_reporting_op_types - Defines different types of * operations for which %QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING can be * used. Will be used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE. * * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START: Sent by userspace to the driver * to request the driver to start reporting Beacon frames. * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP: Sent by userspace to the driver * to request the driver to stop reporting Beacon frames. * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO: Sent by the driver to * userspace to report received Beacon frames. * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE: Sent by the driver to userspace * to indicate that the driver is going to pause reporting Beacon frames. */ enum qca_wlan_vendor_beacon_reporting_op_types { QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START = 0, QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP = 1, QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO = 2, QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE = 3, }; /** * enum qca_wlan_vendor_beacon_reporting_pause_reasons - Defines different * types of reasons for which the driver is pausing reporting Beacon frames. * Will be used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON. * * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED: For unspecified * reasons. * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED: When the * driver/firmware is starting a scan. * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED: When the * driver/firmware disconnects from the ESS and indicates the disconnection to * userspace (non-seamless roaming case). This reason code will be used by the * driver/firmware to indicate stopping of beacon report events. Userspace * will need to start beacon reporting again (if desired) by sending vendor * command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING with * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START after the next connection is * completed. */ enum qca_wlan_vendor_beacon_reporting_pause_reasons { QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED = 0, QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED = 1, QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED = 2, }; /* * enum qca_wlan_vendor_attr_beacon_reporting_params - List of attributes used * in vendor sub-command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING. */ enum qca_wlan_vendor_attr_beacon_reporting_params { QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_INVALID = 0, /* Specifies the type of operation that the vendor command/event is * intended for. Possible values for this attribute are defined in * enum qca_wlan_vendor_beacon_reporting_op_types. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE = 1, /* Optionally set by userspace to request the driver to report Beacon * frames using asynchronous vendor events when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute. * If this flag is not set, the driver will only update Beacon frames * in cfg80211 scan cache but not send any vendor events. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_ACTIVE_REPORTING = 2, /* Optionally used by userspace to request the driver/firmware to * report Beacon frames periodically when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. * u32 attribute, indicates the period of Beacon frames to be reported * and in the units of beacon interval. * If this attribute is missing in the command, then the default value * of 1 will be assumed by driver, i.e., to report every Beacon frame. * Zero is an invalid value. * If a valid value is received for this attribute, the driver will * update the cfg80211 scan cache periodically as per the value * received in this attribute in addition to updating the cfg80211 scan * cache when there is significant change in Beacon frame IEs. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PERIOD = 3, /* Used by the driver to encapsulate the SSID when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. * u8 array with a maximum size of 32. * * When generating beacon report from non-MBSSID Beacon frame, the SSID * will be taken from the SSID element of the received Beacon frame. * * When generating beacon report from Multiple BSSID Beacon frame and * if the BSSID of the current connected BSS matches the BSSID of the * transmitting BSS, the SSID will be taken from the SSID element of * the received Beacon frame. * * When generating beacon report from Multiple BSSID Beacon frame and * if the BSSID of the current connected BSS matches the BSSID of one * of the* nontransmitting BSSs, the SSID will be taken from the SSID * field included in the nontransmitted BSS profile whose derived BSSI * is same as the BSSID of the current connected BSS. When there is no * nontransmitted BSS profile whose derived BSSID is same as the BSSID * of current connected* BSS, this attribute will not be present. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_SSID = 4, /* Used by the driver to encapsulate the BSSID of the AP to which STA * is currently connected to when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array with a * fixed size of 6 bytes. * * When generating beacon report from a Multiple BSSID beacon and the * current connected BSSID matches one of the nontransmitted BSSIDs in * a Multiple BSSID set, this BSSID will be that particular * nontransmitted BSSID and not the transmitted BSSID (i.e., the * transmitting address of the Beacon frame). */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BSSID = 5, /* Used by the driver to encapsulate the frequency in MHz on which * the Beacon frame was received when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is * set to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_FREQ = 6, /* Used by the driver to encapsulate the Beacon interval * when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. * u16 attribute. The value will be copied from the Beacon frame and * the units are TUs. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BI = 7, /* Used by the driver to encapsulate the Timestamp field from the * Beacon frame when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE * is set to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. * u64 attribute. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_TSF = 8, /* Used by the driver to encapsulate the CLOCK_BOOTTIME when this * Beacon frame is received in the driver when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u64 attribute, in * the units of nanoseconds. This value is expected to have accuracy of * about 10 ms. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BOOTTIME_WHEN_RECEIVED = 9, /* Used by the driver to encapsulate the IEs of the Beacon frame from * which this event is generated when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_IES = 10, /* Used by the driver to specify the reason for the driver/firmware to * pause sending beacons to userspace when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. Possible values are * defined in enum qca_wlan_vendor_beacon_reporting_pause_reasons, u32 * attribute. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON = 11, /* Used by the driver to specify whether the driver will automatically * resume reporting beacon events to userspace later (for example after * the ongoing off-channel activity is completed etc.) when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. NLA_FLAG attribute. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES = 12, /* Optionally set by userspace to request the driver not to resume * beacon reporting after a pause is completed, when the * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute. * If this flag is set, the driver will not resume beacon reporting * after any pause in beacon reporting is completed. Userspace has to * send QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command again in order * to initiate beacon reporting again. If this flag is set in the recent * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command, then in the * subsequent QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE event (if any) * the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES shall not be * set by the driver. Setting this flag until and unless there is a * specific need is not recommended as there is a chance of some beacons * received after pause command and next start command being not * reported. */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME = 13, /* Keep last */ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST, QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_MAX = QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST - 1 }; /** * enum qca_vendor_oem_device_type - Represents the target device in firmware. * It is used by QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO. * * @QCA_VENDOR_OEM_DEVICE_VIRTUAL: The command is intended for * a virtual device. * * @QCA_VENDOR_OEM_DEVICE_PHYSICAL: The command is intended for * a physical device. */ enum qca_vendor_oem_device_type { QCA_VENDOR_OEM_DEVICE_VIRTUAL = 0, QCA_VENDOR_OEM_DEVICE_PHYSICAL = 1, }; /* * enum qca_wlan_vendor_attr_oem_data_params - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_OEM_DATA. * * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA: This NLA_BINARY attribute is * used to set/query the data to/from the firmware. On query, the same * attribute is used to carry the respective data in the reply sent by the * driver to userspace. The request to set/query the data and the format of the * respective data from the firmware are embedded in the attribute. The * maximum size of the attribute payload is 1024 bytes. * * @QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO: The binary blob will be routed * based on this field. This optional attribute is included to specify whether * the device type is a virtual device or a physical device for the command. * This attribute can be omitted for a virtual device (default) command. * This u8 attribute is used to carry information for the device type using * values defined by enum qca_vendor_oem_device_type. * * Userspace has to set the QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED * attribute when the data is queried from the firmware. * * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED: This NLA_FLAG attribute * is set when the userspace queries data from the firmware. This attribute * should not be set when userspace sets the OEM data to the firmware. */ enum qca_wlan_vendor_attr_oem_data_params { QCA_WLAN_VENDOR_ATTR_OEM_DATA_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA = 1, QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO = 2, QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_avoid_frequency_ext - Defines attributes to be * used with vendor command/event QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT. * * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE: Required * Nested attribute containing multiple ranges with following attributes: * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START, * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END, and * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM. * * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START: Required (u32) * Starting center frequency in MHz. * * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END: Required (u32) * Ending center frequency in MHz. * * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM: * s32 attribute, optional. It is a per frequency range attribute. * The maximum TX power limit from user space is to be applied on an * unrestricted interface for corresponding frequency range. It is also * possible that the actual TX power may be even lower than this cap due to * other considerations such as regulatory compliance, SAR, etc. In absence of * this attribute the driver shall follow current behavior which means * interface (SAP/P2P) function can keep operating on an unsafe channel with TX * power derived by the driver based on regulatory/SAR during interface up. * * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_IFACES_BITMASK: * u32 attribute, optional. Indicates all the interface types which are * restricted for all frequency ranges provided in * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START and * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END. * This attribute encapsulates bitmasks of interface types defined in * enum nl80211_iftype. If an interface is marked as restricted the driver must * move to a safe channel and if no safe channel is available the driver shall * terminate that interface functionality. In absence of this attribute, * interface (SAP/P2P) can still continue operating on an unsafe channel with * TX power limit derived from either * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM or based on * regulatory/SAE limits if %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM * is not provided. */ enum qca_wlan_vendor_attr_avoid_frequency_ext { QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE = 1, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START = 2, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END = 3, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM = 4, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_IFACES_BITMASK = 5, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_MAX = QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST - 1 }; /* * enum qca_wlan_vendor_attr_add_sta_node_params - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE. */ enum qca_wlan_vendor_attr_add_sta_node_params { QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_INVALID = 0, /* 6 byte MAC address of STA */ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_MAC_ADDR = 1, /* Authentication algorithm used by the station of size u16; * defined in enum nl80211_auth_type. */ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_AUTH_ALGO = 2, /* * This flag attribute is set if the node being added is an * MLD STA node. */ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_IS_ML = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST - 1 }; /** * enum qca_btc_chain_mode - Specifies BT coex chain mode. * This enum defines the valid set of values of BT coex chain mode. * These values are used by attribute %QCA_VENDOR_ATTR_BTC_CHAIN_MODE of * %QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE. * * @QCA_BTC_CHAIN_SHARED: chains of BT and WLAN 2.4 GHz are shared. * @QCA_BTC_CHAIN_SEPARATED_HYBRID: chains of BT and WLAN 2.4 GHz are * separated, hybrid mode. * @QCA_BTC_CHAIN_SEPARATED_FDD: chains of BT and WLAN 2.4 GHz are * separated, fixed FDD mode. */ enum qca_btc_chain_mode { QCA_BTC_CHAIN_SHARED = 0, QCA_BTC_CHAIN_SEPARATED_HYBRID = 1, QCA_BTC_CHAIN_SEPARATED_FDD = 2, }; /* deprecated legacy name */ #define QCA_BTC_CHAIN_SEPARATED QCA_BTC_CHAIN_SEPARATED_HYBRID /** * enum qca_vendor_attr_btc_chain_mode - Specifies attributes for BT coex * chain mode. * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE. * * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE: u32 attribute. * Indicates the BT coex chain mode, are 32-bit values from * enum qca_btc_chain_mode. This attribute is mandatory. * * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE_RESTART: flag attribute. * If set, vdev should be restarted when BT coex chain mode is updated. * This attribute is optional. */ enum qca_vendor_attr_btc_chain_mode { QCA_VENDOR_ATTR_BTC_CHAIN_MODE_INVALID = 0, QCA_VENDOR_ATTR_BTC_CHAIN_MODE = 1, QCA_VENDOR_ATTR_BTC_CHAIN_MODE_RESTART = 2, /* Keep last */ QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST, QCA_VENDOR_ATTR_BTC_CHAIN_MODE_MAX = QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST - 1, }; /** * enum qca_vendor_wlan_sta_flags - Station feature flags * Bits will be set to 1 if the corresponding features are enabled. * @QCA_VENDOR_WLAN_STA_FLAG_AMPDU: AMPDU is enabled for the station * @QCA_VENDOR_WLAN_STA_FLAG_TX_STBC: TX Space-time block coding is enabled for the station * @QCA_VENDOR_WLAN_STA_FLAG_RX_STBC: RX Space-time block coding is enabled for the station */ enum qca_vendor_wlan_sta_flags { QCA_VENDOR_WLAN_STA_FLAG_AMPDU = BIT(0), QCA_VENDOR_WLAN_STA_FLAG_TX_STBC = BIT(1), QCA_VENDOR_WLAN_STA_FLAG_RX_STBC = BIT(2), }; /** * enum qca_vendor_wlan_sta_guard_interval - Station guard interval * @QCA_VENDOR_WLAN_STA_GI_800_NS: Legacy normal guard interval * @QCA_VENDOR_WLAN_STA_GI_400_NS: Legacy short guard interval * @QCA_VENDOR_WLAN_STA_GI_1600_NS: Guard interval used by HE * @QCA_VENDOR_WLAN_STA_GI_3200_NS: Guard interval used by HE */ enum qca_vendor_wlan_sta_guard_interval { QCA_VENDOR_WLAN_STA_GI_800_NS = 0, QCA_VENDOR_WLAN_STA_GI_400_NS = 1, QCA_VENDOR_WLAN_STA_GI_1600_NS = 2, QCA_VENDOR_WLAN_STA_GI_3200_NS = 3, }; /** * enum qca_wlan_vendor_attr_get_sta_info - Defines attributes * used by QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC: * Required attribute in request for AP mode only, 6-byte MAC address, * corresponding to the station's MAC address for which information is * requested. For STA mode this is not required as the info always correspond * to the self STA and the current/last association. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS: * Optionally used in response, u32 attribute, contains a bitmap of different * fields defined in enum qca_vendor_wlan_sta_flags, used in AP mode only. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL: * Optionally used in response, u32 attribute, possible values are defined in * enum qca_vendor_wlan_sta_guard_interval, used in AP mode only. * Guard interval used by the station. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT: * Optionally used in response, u32 attribute, used in AP mode only. * Value indicates the number of data frames received from station with retry * bit set to 1 in FC. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT: * Optionally used in response, u32 attribute, used in AP mode only. * Counter for number of data frames with broadcast or multicast address in * the destination address received from the station. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED: * Optionally used in response, u32 attribute, used in both STA and AP modes. * Value indicates the number of data frames successfully transmitted only * after retrying the packets and for which the TX status has been updated * back to host from target. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED: * Optionally used in response, u32 attribute, used in both STA and AP mode. * Value indicates the number of data frames not transmitted successfully even * after retrying the packets for the number of times equal to the total number * of retries allowed for that packet and for which the TX status has been * updated back to host from target. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL: * Optionally used in response, u32 attribute, used in AP mode only. * Counter in the target for the number of data frames successfully transmitted * to the station. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY: * Optionally used in response, u32 attribute, used in AP mode only. * Value indicates the number of data frames successfully transmitted only * after retrying the packets. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED: * Optionally used in response, u32 attribute, used in both STA & AP mode. * Value indicates the number of data frames not transmitted successfully even * after retrying the packets for the number of times equal to the total number * of retries allowed for that packet. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT: u32, used in * the STA mode only. Represent the number of probe requests sent by the STA * while attempting to roam on missing certain number of beacons from the * connected AP. If queried in the disconnected state, this represents the * count for the last connected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT: u32, used in * the STA mode. Represent the number of probe responses received by the station * while attempting to roam on missing certain number of beacons from the * connected AP. When queried in the disconnected state, this represents the * count when in last connected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT: u32, used in the * STA mode only. Represents the total number of frames sent out by STA * including Data, ACK, RTS, CTS, Control Management. This data is maintained * only for the connect session. Represents the count of last connected session, * when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT: u32, used in the STA mode. * Total number of RTS sent out by the STA. This data is maintained per connect * session. Represents the count of last connected session, when queried in the * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT: u32, used in the * STA mode.Represent the number of RTS transmission failure that reach retry * limit. This data is maintained per connect session. Represents the count of * last connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT: u32, used in * the STA mode. Represent the total number of non aggregated frames transmitted * by the STA. This data is maintained per connect session. Represents the count * of last connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT: u32, used in the * STA mode. Represent the total number of aggregated frames transmitted by the * STA. This data is maintained per connect session. Represents the count of * last connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT: u32, used in * the STA mode. Represents the number of received frames with a good PLCP. This * data is maintained per connect session. Represents the count of last * connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT: u32, * used in the STA mode. Represents the number of occasions that no valid * delimiter is detected by A-MPDU parser. This data is maintained per connect * session. Represents the count of last connected session, when queried in the * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT: u32, used in the * STA mode. Represents the number of frames for which CRC check failed in the * MAC. This data is maintained per connect session. Represents the count of * last connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT: u32, used in the * STA mode. Represents the number of unicast ACKs received with good FCS. This * data is maintained per connect session. Represents the count of last * connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT: u32, used in the STA * mode. Represents the number of received Block Acks. This data is maintained * per connect session. Represents the count of last connected session, when * queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT: u32, used in the STA * mode. Represents the number of beacons received from the connected BSS. This * data is maintained per connect session. Represents the count of last * connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT: u32, used in the * STA mode. Represents the number of beacons received by the other BSS when in * connected state (through the probes done by the STA). This data is maintained * per connect session. Represents the count of last connected session, when * queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT: u64, used in * the STA mode. Represents the number of received DATA frames with good FCS and * matching Receiver Address when in connected state. This data is maintained * per connect session. Represents the count of last connected session, when * queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT: u32, used in the * STA mode. Represents the number of RX Data multicast frames dropped by the HW * when in the connected state. This data is maintained per connect session. * Represents the count of last connected session, when queried in the * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS: u32, used in the * STA mode. This represents the target power in dBm for the transmissions done * to the AP in 2.4 GHz at 1 Mbps (DSSS) rate. This data is maintained per * connect session. Represents the count of last connected session, when * queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS: u32, used in the * STA mode. This represents the Target power in dBm for transmissions done to * the AP in 2.4 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect * session. Represents the count of last connected session, when queried in the * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0: u32, used in the * STA mode. This represents the Target power in dBm for transmissions done to * the AP in 2.4 GHz at MCS0 rate. This data is maintained per connect session. * Represents the count of last connected session, when queried in the * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS: u32, used in the * STA mode. This represents the Target power in dBm for transmissions done to * the AP in 5 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect * session. Represents the count of last connected session, when queried in * the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0: u32, used in the * STA mode. This represents the Target power in dBm for for transmissions done * to the AP in 5 GHz at MCS0 rate. This data is maintained per connect session. * Represents the count of last connected session, when queried in the * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT: u32, used * in the STA mode. This represents the Nested attribute representing the * overflow counts of each receive buffer allocated to the hardware during the * STA's connection. The number of hw buffers might vary for each WLAN * solution and hence this attribute represents the nested array of all such * HW buffer count. This data is maintained per connect session. Represents * the count of last connected session, when queried in the disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER: u32, Max TX power (dBm) * allowed as per the regulatory requirements for the current or last connected * session. Used in the STA mode. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER: u32, Latest TX power * (dBm) used by the station in its latest unicast frame while communicating * to the AP in the connected state. When queried in the disconnected state, * this represents the TX power used by the STA with last AP communication * when in connected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL: u32, Adaptive noise immunity * level used to adjust the RX sensitivity. Represents the current ANI level * when queried in the connected state. When queried in the disconnected * state, this corresponds to the latest ANI level at the instance of * disconnection. * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT: u32, used in STA mode * only. This represents the number of group addressed robust management frames * received from this station with an invalid MIC or a missing MME when PMF is * enabled. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT: u32, used in STA mode * only. This represents the number of group addressed robust management frames * received from this station with the packet number less than or equal to the * last received packet number when PMF is enabled. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT: u32, used in STA * mode only. This represents the number of Beacon frames received from this * station with an invalid MIC or a missing MME when beacon protection is * enabled. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT: u32, used in STA mode * only. This represents number of Beacon frames received from this station with * the packet number less than or equal to the last received packet number when * beacon protection is enabled. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE: u32, used in * STA mode only. Driver uses this attribute to populate the connection failure * reason codes and the values are defined in * enum qca_sta_connect_fail_reason_codes. Userspace applications can send * QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command after receiving * connection failure from driver. The driver shall not include this attribute * in response to QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO command if there is no * connection failure observed in the last attempted connection. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_RATE: u32, latest TX rate (Kbps) * used by the station in its last TX frame while communicating to the AP in the * connected state. When queried in the disconnected state, this represents the * rate used by the STA in the last TX frame to the AP when it was connected. * This attribute is used for STA mode only. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_RIX: u32, used in STA mode only. * This represents the rate index used by the STA for the last TX frame to the * AP. When queried in the disconnected state, this gives the last RIX used by * the STA in the last TX frame to the AP when it was connected. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TSF_OUT_OF_SYNC_COUNT: u32, used in STA * mode only. This represents the number of times the STA TSF goes out of sync * from the AP after the connection. If queried in the disconnected state, this * gives the count of TSF out of sync for the last connection. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_TRIGGER_REASON: u32, used in STA * mode only. This represents the roam trigger reason for the last roaming * attempted by the firmware. This can be queried either in connected state or * disconnected state. Each bit of this attribute represents the different * roam trigger reason code which are defined in enum qca_vendor_roam_triggers. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON: u32, used in STA mode * only. This represents the roam fail reason for the last failed roaming * attempt by the firmware. Different roam failure reason codes are specified * in enum qca_vendor_roam_fail_reasons. This can be queried either in * connected state or disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON: u32, used in * STA mode only. This represents the roam invoke fail reason for the last * failed roam invoke. Different roam invoke failure reason codes * are specified in enum qca_vendor_roam_invoke_fail_reasons. This can be * queried either in connected state or disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY: u32, used in STA mode only. * This represents the average congestion duration of uplink frames in MAC * queue in unit of ms. This can be queried either in connected state or * disconnected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_TX_PACKETS: Mandatory u32 Nested * attribute, used in AP mode. This represents the MPDU packet count per MCS * rate value of TX packets. Every index of this nested attribute corresponds * to MCS index, for example Index 0 represents MCS0 TX rate. This can be * queried in connected state. * * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_RX_PACKETS: Mandatory u32 Nested * attribute, used in AP mode. This represents the MPDU packet count per MCS * rate value of RX packets. Every index of this nested attribute corresponds * to MCS index, for example Index 0 represents MCS0 RX rate. This can be * queried in connected state. */ enum qca_wlan_vendor_attr_get_sta_info { QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC = 1, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS = 2, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL = 3, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT = 4, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT = 5, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED = 6, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED = 7, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL = 8, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY = 9, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED = 10, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT = 11, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT = 12, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT = 13, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT = 14, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT = 15, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT = 16, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT = 17, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT = 18, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT = 19, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT = 20, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT = 21, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT = 22, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT = 23, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT = 24, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT = 25, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT = 26, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS = 27, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS = 28, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0 = 29, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS = 30, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0 = 31, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT = 32, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER = 33, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER = 34, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL = 35, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT = 39, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT = 40, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT = 41, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT = 42, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE = 43, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_RATE = 44, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_RIX = 45, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TSF_OUT_OF_SYNC_COUNT = 46, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_TRIGGER_REASON = 47, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON = 48, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON = 49, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY = 50, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_TX_PACKETS = 51, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_RX_PACKETS = 52, /* keep last */ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX = QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST - 1, }; /** * enum qca_disconnect_reason_codes - Specifies driver disconnect reason codes. * Used when the driver triggers the STA to disconnect from the AP. * * @QCA_DISCONNECT_REASON_UNSPECIFIED: The host driver triggered the * disconnection with the AP due to unspecified reasons. * * @QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE: The host driver triggered the * disconnection with the AP due to a roaming failure. This roaming is triggered * internally (host driver/firmware). * * @QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE: The driver disconnected from * the AP when the user/external triggered roaming fails. * * @QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE: This reason code is used * by the host driver whenever gateway reachability failure is detected and the * driver disconnects with AP. * * @QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA: The driver disconnected from * the AP on a channel switch announcement from it with an unsupported channel. * * @QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR: On a concurrent AP start * with indoor channels disabled and if the STA is connected on one of these * disabled channels, the host driver disconnected the STA with this reason * code. * * @QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED: Disconnection due to an * explicit request from the user to disable the current operating channel. * * @QCA_DISCONNECT_REASON_DEVICE_RECOVERY: STA disconnected from the AP due to * the internal host driver/firmware recovery. * * @QCA_DISCONNECT_REASON_KEY_TIMEOUT: The driver triggered the disconnection on * a timeout for the key installations from the user space. * * @QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE: The dDriver disconnected the * STA on a band change request from the user space to a different band from the * current operation channel/band. * * @QCA_DISCONNECT_REASON_IFACE_DOWN: The STA disconnected from the AP on an * interface down trigger from the user space. * * @QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL: The host driver disconnected the * STA on getting continuous transmission failures for multiple Data frames. * * @QCA_DISCONNECT_REASON_PEER_INACTIVITY: The STA does a keep alive * notification to the AP by transmitting NULL/G-ARP frames. This disconnection * represents inactivity from AP on such transmissions. * @QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT: This reason code is used on * disconnection when SA Query times out (AP does not respond to SA Query). * * @QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE: The host driver disconnected the * STA on missing the beacons continuously from the AP. * * @QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE: Disconnection due to STA not * able to move to the channel mentioned by the AP in CSA. * * @QCA_DISCONNECT_REASON_USER_TRIGGERED: User triggered disconnection. */ enum qca_disconnect_reason_codes { QCA_DISCONNECT_REASON_UNSPECIFIED = 0, QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE = 1, QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE = 2, QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE = 3, QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA = 4, QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR = 5, QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED = 6, QCA_DISCONNECT_REASON_DEVICE_RECOVERY = 7, QCA_DISCONNECT_REASON_KEY_TIMEOUT = 8, QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE = 9, QCA_DISCONNECT_REASON_IFACE_DOWN = 10, QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL = 11, QCA_DISCONNECT_REASON_PEER_INACTIVITY = 12, QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT = 13, QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE = 14, QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE = 15, QCA_DISCONNECT_REASON_USER_TRIGGERED = 16, }; /** * enum qca_wlan_vendor_attr_driver_disconnect_reason - Defines attributes * used by %QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON vendor command. * * @QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE: u32 attribute. * This attribute represents the driver specific reason codes (local * driver/firmware initiated reasons for disconnection) defined * in enum qca_disconnect_reason_codes. */ enum qca_wlan_vendor_attr_driver_disconnect_reason { QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_MAX = QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST - 1, }; /** * enum qca_wlan_tspec_operation - Operation of the config TSPEC request * * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION. */ enum qca_wlan_tspec_operation { QCA_WLAN_TSPEC_ADD = 0, QCA_WLAN_TSPEC_DEL = 1, QCA_WLAN_TSPEC_GET = 2, }; /** * enum qca_wlan_tspec_direction - Direction in TSPEC * As what is defined in IEEE Std 802.11-2016, Table 9-139. * * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION. */ enum qca_wlan_tspec_direction { QCA_WLAN_TSPEC_DIRECTION_UPLINK = 0, QCA_WLAN_TSPEC_DIRECTION_DOWNLINK = 1, QCA_WLAN_TSPEC_DIRECTION_DIRECT = 2, QCA_WLAN_TSPEC_DIRECTION_BOTH = 3, }; /** * enum qca_wlan_tspec_ack_policy - MAC acknowledgment policy in TSPEC * As what is defined in IEEE Std 802.11-2016, Table 9-141. * * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY. */ enum qca_wlan_tspec_ack_policy { QCA_WLAN_TSPEC_NORMAL_ACK = 0, QCA_WLAN_TSPEC_NO_ACK = 1, /* Reserved */ QCA_WLAN_TSPEC_BLOCK_ACK = 3, }; /** * enum qca_wlan_vendor_attr_config_tspec - Defines attributes * used by QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC vendor command. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION: * u8 attribute. Specify the TSPEC operation of this request. Possible values * are defined in enum qca_wlan_tspec_operation. * Mandatory attribute for all kinds of config TSPEC requests. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID: * u8 attribute. TS ID. Possible values are 0-7. * Applicable for operation: QCA_WLAN_TSPEC_ADD, QCA_WLAN_TSPEC_DEL, * QCA_WLAN_TSPEC_GET. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION: * u8 attribute. Direction of data carried by the TS. Possible values are * defined in enum qca_wlan_tspec_direction. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD: * Flag attribute. Indicate whether APSD is enabled for the traffic associated * with the TS. set - enabled, not set - disabled. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY: * u8 attribute. User priority to be used for the transport of MSDUs/ -MSDUs * belonging to this TS. Possible values are 0-7. * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY: * u8 attribute. Indicate whether MAC acknowledgements are required for * MPDUs/A-MSDUs belonging to this TS and the form of those acknowledgements. * Possible values are defined in enum qca_wlan_tspec_ack_policy. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE: * u16 attribute. Specify the nominal size in bytes of MSDUs/A-MSDUs * belonging to this TS. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE: * u16 attribute. Specify the maximum size in bytes of MSDUs/A-MSDUs * belonging to this TS. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL: * u32 attribute. Specify the minimum interval in microseconds between the * start of two successive SPs. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL: * u32 attribute. Specify the maximum interval in microseconds between the * start of two successive SPs. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL: * u32 attribute. Specify the minimum interval in microseconds that can elapse * without arrival or transfer of an MPDU belonging to the TS before this TS * is deleted by the MAC entity at the HC. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL: * u32 attribute. Specify the minimum interval in microseconds that can elapse * without arrival or transfer of an MSDU belonging to the TS before the * generation of successive QoS(+)CF-Poll is stopped for this TS. A value of * 0xFFFFFFFF disables the suspension interval. The value of the suspension * interval is always less than or equal to the inactivity interval. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE: * u32 attribute. Indicate the lowest data rate in bps specified at the MAC * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the * bounds of this TSPEC. * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE: * u32 attribute. Indicate the average data rate in bps specified at the MAC * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the * bounds of this TSPEC. * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE: * u32 attribute. Indicate the maximum allowable data rate in bps specified at * the MAC SAP for transport of MSDUs or A-MSDUs belonging to this TS within * the bounds of this TSPEC. * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE: * u32 attribute. Specify the maximum burst size in bytes of the MSDUs/A-MSDUs * belonging to this TS that arrive at the MAC SAP at the peak data rate. A * value of 0 indicates that there are no bursts. * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE: * u32 attribute. Indicate the minimum PHY rate in bps for transport of * MSDUs/A-MSDUs belonging to this TS within the bounds of this TSPEC. * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE: * u16 attribute. Specify the excess allocation of time (and bandwidth) over * and above the stated application rates required to transport an MSDU/A-MSDU * belonging to the TS in this TSPEC. * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. */ enum qca_wlan_vendor_attr_config_tspec { QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION = 1, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID = 2, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION = 3, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD = 4, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY = 5, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY = 6, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE = 7, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE = 8, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL = 9, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL = 10, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL = 11, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL = 12, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE = 13, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE = 14, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE = 15, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE = 16, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE = 17, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE = 18, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX = QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST - 1, }; /** * enum qca_wlan_medium_assess_type - Type of medium assess request * * Values for %QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE. */ enum qca_wlan_medium_assess_type { QCA_WLAN_MEDIUM_ASSESS_CCA = 0, QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT = 1, }; /** * enum qca_wlan_vendor_attr_medium_assess - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS vendor command. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE: * u8 attribute. Mandatory in all kinds of medium assess requests/responses. * Specify the type of medium assess request and indicate its type in response. * Possible values are defined in enum qca_wlan_medium_assess_type. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD: * u32 attribute. Mandatory in CCA request. * Specify the assessment period in terms of seconds. Assessment result will be * sent as the response to the CCA request after the assessment period. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT: * u32 attribute. Mandatory in response to CCA request. * Total timer tick count of the assessment cycle. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT: * u32 attribute. Mandatory in response to CCA request. * Timer tick count of idle time in the assessment cycle. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT: * u32 attribute. Mandatory in response to CCA request. * Timer tick count of Intra BSS traffic RX time in the assessment cycle. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT: * u32 attribute. Mandatory in response to CCA request. * Timer tick count of Overlapping BSS traffic RX time in the assessment cycle. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI: * s32 attribute. Mandatory in response to CCA request. * Maximum RSSI of Intra BSS traffic in the assessment cycle. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI: * s32 attribute. Mandatory in response to CCA request. * Minimum RSSI of Intra BSS traffic in the assessment cycle. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE: * u8 attribute. Mandatory in congestion report request. * 1-enable 0-disable. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD: * u8 attribute. Mandatory in congestion report enable request and will be * ignored if present in congestion report disable request. Possible values are * 0-100. A vendor event QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS with the type * QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT will be sent to userspace if * congestion percentage reaches the configured threshold. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL: * u8 attribute. Optional in congestion report enable request and will be * ignored if present in congestion report disable request. * Specify the interval of congestion report event in terms of seconds. Possible * values are 1-255. Default value 1 will be used if this attribute is omitted * or using invalid values. * * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE: * u8 attribute. Mandatory in congestion report event. * Indicate the actual congestion percentage. Possible values are 0-100. */ enum qca_wlan_vendor_attr_medium_assess { QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE = 1, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD = 2, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT = 3, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT = 4, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT = 5, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT = 6, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI = 7, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI = 8, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE = 9, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD = 10, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL = 11, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE = 12, /* keep last */ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX = QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mbssid_tx_vdev_status - Defines attributes * used by QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS vendor command. * * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_VAL: * u8 attribute. Notify the TX VDEV status. Possible values 0, 1 * belonging to MBSSID/EMA_AP configuration. 0 means Non-Tx VDEV, * 1 means Tx VDEV. Mandatory attribute for all MBSSID VDEV status events. * * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_EVENT: * u8 attribute, required. 1 means Tx VDEV up event.0 mean Tx VDEV down event. * * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_ID: * u8 attribute, required. indicates group id of Tx VDEV * * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO: * Nested attribute. This attribute shall be used by the driver to send * group information. The attributes defined in enum * qca_wlan_vendor_attr_mbssid_tx_vdev_group_info * are nested in this attribute. */ enum qca_wlan_vendor_attr_mbssid_tx_vdev_status { QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_VAL = 1, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_EVENT = 2, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_ID = 3, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_MAX = QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mbssid_tx_vdev_group_info - Attributes used * inside %QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO nested attribute. * * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_IF_INDEX: * u32 attribute, required. contains interface index. * * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_STATUS: * u8 attribute, required. 0 - means vdev is in down state. * 1- means vdev is in up state. */ enum qca_wlan_vendor_attr_mbssid_tx_vdev_group_info { QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_IF_INDEX = 1, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_STATUS = 2, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_MAX = QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO - 1, }; /** * enum qca_wlan_vendor_oci_override_frame_type - OCI override frame type * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ: SA Query Request frame * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP: SA Query Response frame * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ: FT Reassociation Request * frame * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ: FILS Reassociation * Request frame. */ enum qca_wlan_vendor_oci_override_frame_type { QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ = 1, QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP = 2, QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ = 3, QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ = 4, }; /** * enum qca_wlan_concurrent_sta_policy_config - Concurrent STA policies * * @QCA_WLAN_CONCURRENT_STA_POLICY_PREFER_PRIMARY: Preference to the primary * STA interface has to be given while selecting the connection policies * (e.g., BSSID, band, TX/RX chains, etc.) for the subsequent STA interface. * An interface is set as primary through the attribute * QCA_WLAN_VENDOR_ATTR_CONFIG_CONCURRENT_STA_PRIMARY. This policy is not * applicable if the primary interface has not been set earlier. * * The intention is not to downgrade the primary STA performance, such as: * - Do not reduce the number of TX/RX chains of primary connection. * - Do not optimize DBS vs. MCC/SCC, if DBS ends up reducing the number of * chains. * - If using MCC, should set the MCC duty cycle of the primary connection to * be higher than the secondary connection. * * @QCA_WLAN_CONCURRENT_STA_POLICY_UNBIASED: The connection policies for the * subsequent STA connection shall be chosen to balance with the existing * concurrent STA's performance. * Such as * - Can choose MCC or DBS mode depending on the MCC efficiency and hardware * capability. * - If using MCC, set the MCC duty cycle of the primary connection to be equal * to the secondary. * - Prefer BSSID candidates which will help provide the best "overall" * performance for all the STA connections. */ enum qca_wlan_concurrent_sta_policy_config { QCA_WLAN_CONCURRENT_STA_POLICY_PREFER_PRIMARY = 0, QCA_WLAN_CONCURRENT_STA_POLICY_UNBIASED = 1, }; /** * enum qca_wlan_concurrent_ap_policy_config - Concurrent AP policies * * @QCA_WLAN_CONCURRENT_AP_POLICY_UNSPECIFIED: No specific policy for this AP * interface. * * @QCA_WLAN_CONCURRENT_AP_POLICY_GAMING_AUDIO: Select interface concurrencies * to meet gaming audio latency requirements. * * @QCA_WLAN_CONCURRENT_AP_POLICY_LOSSLESS_AUDIO_STREAMING: Select interface * concurrencies to meet lossless audio streaming requirements. * * @QCA_WLAN_CONCURRENT_AP_POLICY_XR: Select interface concurrencies to meet * XR (eXtended Reality) requirements. */ enum qca_wlan_concurrent_ap_policy_config { QCA_WLAN_CONCURRENT_AP_POLICY_UNSPECIFIED = 0, QCA_WLAN_CONCURRENT_AP_POLICY_GAMING_AUDIO = 1, QCA_WLAN_CONCURRENT_AP_POLICY_LOSSLESS_AUDIO_STREAMING = 2, QCA_WLAN_CONCURRENT_AP_POLICY_XR = 3, }; /** * enum qca_wlan_vendor_attr_concurrent_policy - Defines attributes * used by QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY vendor command. * * @QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_STA_CONFIG: * u8 attribute. Configures the concurrent STA policy configuration. * Possible values are defined in enum qca_wlan_concurrent_sta_policy_config. * @QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG: * u8 attribute. Configures the concurrent AP policy configuration. * Possible values are defined in enum qca_wlan_concurrent_ap_policy_config. */ enum qca_wlan_vendor_attr_concurrent_policy { QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_STA_CONFIG = 1, QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_MAX = QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AFTER_LAST - 1, }; /* Compatibility defines for previously used enum * qca_wlan_vendor_attr_concurrent_policy names. These values should not be used * in any new implementation. */ #define QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_CONFIG \ QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_STA_CONFIG #define QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_MAX \ QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_MAX #define qca_wlan_vendor_attr_concurrent_sta_policy \ qca_wlan_vendor_attr_concurrent_policy /** * enum qca_sta_connect_fail_reason_codes - Defines values carried * by QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE vendor * attribute. * @QCA_STA_CONNECT_FAIL_REASON_NO_BSS_FOUND: No probe response frame received * for unicast probe request. * @QCA_STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL: STA failed to send auth request. * @QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED: AP didn't send ACK for * ath request. * @QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED: Auth response is not * received from AP. * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL: STA failed to send assoc * request. * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED: AP didn't send ACK for * assoc request. * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED: Assoc response is not * received from AP. */ enum qca_sta_connect_fail_reason_codes { QCA_STA_CONNECT_FAIL_REASON_NO_BSS_FOUND = 1, QCA_STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL = 2, QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED = 3, QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED = 4, QCA_STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL = 5, QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED = 6, QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED = 7, }; /** * enum qca_wlan_vendor_attr_oci_override: Represents attributes for * OCI override request. These attributes are used inside nested attribute * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE in QCA vendor command * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. * * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE: Required attribute, u8. * Values from enum qca_wlan_vendor_oci_override_frame_type used in this * attribute to specify the frame type in which the OCI is to be overridden. * * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY: Required (u32) * OCI frequency (in MHz) to override in the specified frame type. */ enum qca_wlan_vendor_attr_oci_override { QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE = 1, QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_MAX = QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_usable_channels_filter - Bitmask of different * filters defined in this enum are used in attribute * %QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK. * * @QCA_WLAN_VENDOR_FILTER_CELLULAR_COEX: When this bit is set, the driver * shall filter the channels which are not usable because of coexistence with * cellular radio. * @QCA_WLAN_VENDOR_FILTER_WLAN_CONCURRENCY: When this bit is set, the driver * shall filter the channels which are not usable because of existing active * interfaces in the driver and will result in Multi Channel Concurrency, etc. * */ enum qca_wlan_vendor_usable_channels_filter { QCA_WLAN_VENDOR_FILTER_CELLULAR_COEX = 0, QCA_WLAN_VENDOR_FILTER_WLAN_CONCURRENCY = 1, }; /** * enum qca_wlan_vendor_attr_chan_info - Attributes used inside * %QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO nested attribute. * * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_PRIMARY_FREQ: * u32 attribute, required. Indicates the center frequency of the primary * channel in MHz. * * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG0_FREQ: * u32 attribute. Indicates the center frequency of the primary segment of the * channel in MHz. This attribute is required when reporting 40 MHz, 80 MHz, * 160 MHz, and 320 MHz channels. * * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG1_FREQ: * u32 attribute. Indicates the center frequency of the secondary segment of * 80+80 channel in MHz. This attribute is required only when * QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH is set to NL80211_CHAN_WIDTH_80P80. * * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH: * u32 attribute, required. Indicates the bandwidth of the channel, possible * values are defined in enum nl80211_chan_width. * * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_IFACE_MODE_MASK: * u32 attribute, required. Indicates all the interface types for which this * channel is usable. This attribute encapsulates bitmasks of interface types * defined in enum nl80211_iftype. * */ enum qca_wlan_vendor_attr_chan_info { QCA_WLAN_VENDOR_ATTR_CHAN_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CHAN_INFO_PRIMARY_FREQ = 1, QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG0_FREQ = 2, QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG1_FREQ = 3, QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH = 4, QCA_WLAN_VENDOR_ATTR_CHAN_INFO_IFACE_MODE_MASK = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_CHAN_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CHAN_INFO_MAX = QCA_WLAN_VENDOR_ATTR_CHAN_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_usable_channels - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS vendor command. * * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_BAND_MASK: * u32 attribute. Indicates the bands from which the channels should be reported * in response. This attribute encapsulates bit masks of bands defined in enum * nl80211_band. Optional attribute, if not present in the request the driver * shall return channels from all supported bands. * * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_IFACE_MODE_MASK: * u32 attribute. Indicates all the interface types for which the usable * channels information is requested. This attribute encapsulates bitmasks of * interface types defined in enum nl80211_iftype. Optional attribute, if not * present in the request the driver shall send information of all supported * interface modes. * * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK: * u32 attribute. This attribute carries information of all filters that shall * be applied while populating usable channels information by the driver. This * attribute carries bit masks of different filters defined in enum * qca_wlan_vendor_usable_channels_filter. Optional attribute, if not present * in the request the driver shall send information of channels without applying * any of the filters that can be configured through this attribute. * * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO: * Nested attribute. This attribute shall be used by the driver to send * usability information of each channel. The attributes defined in enum * qca_wlan_vendor_attr_chan_info are used inside this attribute. */ enum qca_wlan_vendor_attr_usable_channels { QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_BAND_MASK = 1, QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_IFACE_MODE_MASK = 2, QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK = 3, QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_MAX = QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_radar_history: Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY to get DFS radar history. * * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES: Nested attribute to carry * the list of radar history entries. * Each entry contains freq, timestamp, and radar signal detect flag. * The driver shall add an entry when CAC has finished, or radar signal * has been detected post AP beaconing. The driver shall maintain at least * 8 entries in order to save CAC result for a 160 MHz channel. * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_FREQ: u32 attribute. * Channel frequency in MHz. * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_TIMESTAMP: u64 nanoseconds. * CLOCK_BOOTTIME timestamp when this entry is updated due to CAC * or radar detection. * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_DETECTED: NLA_FLAG attribute. * This flag indicates radar signal has been detected. */ enum qca_wlan_vendor_attr_radar_history { QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES = 1, QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_FREQ = 2, QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_TIMESTAMP = 3, QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_DETECTED = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_LAST, QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_MAX = QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_LAST - 1, }; /** * enum qca_wlan_vendor_mcc_quota_type: MCC channel time quota type * * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_CLEAR: In the event, it indicates that the * target exited MCC state and cleared the quota information. In the * command it clears MCC quota setting and restores adaptive scheduling. * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_FIXED: Channel time quota is fixed and * will not be changed. * This quota type is present in command/event. * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_DYNAMIC: Channel time quota is dynamic * and the target may change the quota based on the data activity. * This quota type is only present in event. * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY: Channel time quota is optimized * by the target for low latency. * This quota type is only present in command. */ enum qca_wlan_vendor_mcc_quota_type { QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_CLEAR = 0, QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_FIXED = 1, QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_DYNAMIC = 2, QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY = 3, }; /** * enum qca_wlan_vendor_attr_mcc_quota: Used by the vendor event * QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA to indicate MCC channel * quota information or as a command to set the required MCC quota for an * interface. * * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_TYPE: u32 attribute. * The type is defined in enum qca_wlan_vendor_mcc_quota_type. * In a command this specifies the MCC quota type to be set for the interface. * In an event this provides the current quota type in force. * This is required in a command and an event. * * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_ENTRIES: Nested attribute to carry * the list of channel quota entries. * In an event each entry contains the frequency and respective time quota for * all the MCC interfaces. * In a command it specifies the interface index and respective time quota. * In a command only one entry (ifindex, quota pair) may be specified. * * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_FREQ: u32 attribute. * Channel frequency in MHz. This is present only in an event. * * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_TIME_PERCENTAGE: u32 attribute. * Channel time quota expressed as percentage. * This is present in an event and a command. * In an command, the user shall specify the quota to be allocated for the * interface represented by %QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_IFINDEX. * In an event this provides the existing quota for the channel. * * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_IFINDEX: u32 attribute. * Specifies the interface index (netdev) for which the corresponding * configurations are applied. This is required in a command only. Only one * interface index may be specified. If not specified, the configuration is * rejected. * * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LOW_LATENCY_MODE_ENABLE * 8-bit unsigned value to enable/disable Multi-Channel Concurrency * low latency mode. The firmware will do optimization for low * latency in Multi-Channel concurrency state if enabled. And all existing * user quota setting will be overwritten by the target. * 0 - disable(default), 1 - enable. * It is only present in a command with quota type of * QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY. */ enum qca_wlan_vendor_attr_mcc_quota { QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_TYPE = 1, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_ENTRIES = 2, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_FREQ = 3, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_TIME_PERCENTAGE = 4, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_IFINDEX = 5, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LOW_LATENCY_MODE_ENABLE = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LAST, QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_MAX = QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LAST - 1, }; /** * enum qca_wlan_roam_stats_invoke_reason - Roam invoke reason. These values * are used by the attribute * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_USER_TRIGGER_INVOKE_REASON. * * @QCA_WLAN_ROAM_STATS_INVOKE_REASON_UNDEFINED: Default value when target * invoke roam. * @QCA_WLAN_ROAM_STATS_INVOKE_REASON_NUD_FAILURE: Neighbor unreachable * detection failed when the roam trigger. * @QCA_WLAN_ROAM_STATS_INVOKE_REASON_USER_SPACE: Invoke from user space. */ enum qca_wlan_roam_stats_invoke_reason { QCA_WLAN_ROAM_STATS_INVOKE_REASON_UNDEFINED = 0, QCA_WLAN_ROAM_STATS_INVOKE_REASON_NUD_FAILURE = 1, QCA_WLAN_ROAM_STATS_INVOKE_REASON_USER_SPACE = 2, }; /** * enum qca_wlan_roam_stats_tx_failures_reason - Roam TX failures reason. These * values are used by the attribute * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TX_FAILURES_REASON. * * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_UNSPECIFIED: Default value when * roam by kickout. * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_XRETRY: Excessive retry when roam * trigger by kickout. * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_INACTIVITY: Station inactivity when * roam trigger by kickout. * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_IBSS_DISCONNECT: IBSS disconnect when * roam trigger by kickout. * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_TDLS_DISCONNECT: TDLS peer has * disappeared, and all TX is failing when roam trigger by kickout. * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_SA_QUERY_TIMEOUT: SA query process * timeout when roam trigger by kickout. * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_ROAMING_EVENT: Directly connected * peer has roamed to a repeater. */ enum qca_wlan_roam_stats_tx_failures_reason { QCA_WLAN_ROAM_STATS_KICKOUT_REASON_UNSPECIFIED = 0, QCA_WLAN_ROAM_STATS_KICKOUT_REASON_XRETRY = 1, QCA_WLAN_ROAM_STATS_KICKOUT_REASON_INACTIVITY = 2, QCA_WLAN_ROAM_STATS_KICKOUT_REASON_IBSS_DISCONNECT = 3, QCA_WLAN_ROAM_STATS_KICKOUT_REASON_TDLS_DISCONNECT = 4, QCA_WLAN_ROAM_STATS_KICKOUT_REASON_SA_QUERY_TIMEOUT = 5, QCA_WLAN_ROAM_STATS_KICKOUT_REASON_ROAMING_EVENT = 6, }; /** * enum qca_wlan_roam_stats_abort_reason - Roam abort reason. These values * are used by the attribute %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ABORT_REASON. * * @QCA_WLAN_ROAM_STATS_ABORT_UNSPECIFIED: Target did not specify the * detailed reason for roam scan being aborted. * @QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_DATA_RSSI_HIGH: Roam scan is not * started due to high data RSSI during LOW-RSSI roaming. * @QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_LINK_SPEED_GOOD: Roam scan is not * started due to good link speed during LOW-RSSI roaming. * @QCA_WLAN_ROAM_STATS_ABORT_BG_DATA_RSSI_HIGH: Roam scan is not started * due to high data RSSI during background roaming. * @QCA_WLAN_ROAM_STATS_ABORT_BG_RSSI_ABOVE_THRESHOLD: Roam scan is not * started due to high beacon RSSI during background roaming */ enum qca_wlan_roam_stats_abort_reason { QCA_WLAN_ROAM_STATS_ABORT_UNSPECIFIED = 0, QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_DATA_RSSI_HIGH = 1, QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_LINK_SPEED_GOOD = 2, QCA_WLAN_ROAM_STATS_ABORT_BG_DATA_RSSI_HIGH = 3, QCA_WLAN_ROAM_STATS_ABORT_BG_RSSI_ABOVE_THRESHOLD = 4, }; /** * enum qca_wlan_roam_stats_scan_type - Roam scan type define. * These values are used by the attribute * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_TYPE. * * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_PARTIAL: Partial channel scan * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_FULL: Full channel scan * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_NO_SCAN: No roam scan was triggered. * This is generally used in BTM events to indicate BTM frame exchange logs. * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_5GHZ_6GHZ: Higher band roam scan * from 2.4 GHz to 5 GHz or 6 GHz * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_6GHZ: Higher band roam scan from * 5 GHz to 6 GHz */ enum qca_wlan_roam_stats_scan_type { QCA_WLAN_ROAM_STATS_SCAN_TYPE_PARTIAL = 0, QCA_WLAN_ROAM_STATS_SCAN_TYPE_FULL = 1, QCA_WLAN_ROAM_STATS_SCAN_TYPE_NO_SCAN = 2, QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_5GHZ_6GHZ = 3, QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_6GHZ = 4, }; /** * enum qca_wlan_roam_stats_scan_dwell_type - Roam scan dwell type. * These values are used by the attribute * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_DWELL_TYPE. * * @QCA_WLAN_ROAM_STATS_DWELL_TYPE_UNSPECIFIED: Target did not specify the * detailed roam scan type. * @QCA_WLAN_ROAM_STATS_DWELL_ACTIVE_TYPE: Active scan during roam. * @QCA_WLAN_ROAM_STATS_DWELL_PASSIVE_TYPE: Passive scan during roam. */ enum qca_wlan_roam_stats_scan_dwell_type { QCA_WLAN_ROAM_STATS_DWELL_TYPE_UNSPECIFIED = 0, QCA_WLAN_ROAM_STATS_DWELL_TYPE_ACTIVE = 1, QCA_WLAN_ROAM_STATS_DWELL_TYPE_PASSIVE = 2, }; /** * enum qca_wlan_vendor_attr_roam_stats_scan_chan_info - Attributes used inside * the %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_CHAN_INFO nested attribute. */ enum qca_wlan_vendor_attr_roam_stats_scan_chan_info { /* 32-bit unsigned value to indicate center frequency of the primary * channel in MHz for each roam scan channel. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_CHANNEL_FREQ = 1, /* 8-bit unsigned value to indicate channel scan type for each * roam scan channel, values in qca_wlan_roam_stats_scan_dwell_type. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_DWELL_TYPE = 2, /* 32-bit unsigned value to indicate maximum scan time in milliseconds * for each roam scan channel. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_MAX_DWELL_TIME = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_INFO_FRAME_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_roam_stats_frame_subtype - Roam frame subtypes. These values * are used by the attribute %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_SUBTYPE. * * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_RESP: Authentication Response frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_RESP: Reassociation Response frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M1: EAPOL-Key M1 frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M2: EAPOL-Key M2 frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M3: EAPOL-Key M3 frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M4: EAPOL-Key M4 frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M1: EAPOL-Key GTK M1 frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M2: EAPOL-Key GTK M2 frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_REQ: Authentication Request frame * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_REQ: Reassociation Request frame */ enum qca_wlan_roam_stats_frame_subtype { QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_RESP = 1, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_RESP = 2, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M1 = 3, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M2 = 4, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M3 = 5, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M4 = 6, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M1 = 7, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M2 = 8, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_REQ = 9, QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_REQ = 10, }; /* Compatibility defines for previously used names. * These values should not be used in any new implementation. */ #define QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_PREAUTH \ QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_RESP #define QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC \ QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_RESP /** * enum roam_frame_status - Specifies the valid values the vendor roam frame * attribute QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_STATUS can take. * * @QCA_WLAN_ROAM_FRAME_STATUS_SUCCESS: It indicates the roam frame was * sent or received successfully. * @QCA_WLAN_ROAM_FRAME_STATUS_FAIL: It indicates the roam frame sending or * receiving failed. */ enum qca_wlan_roam_stats_frame_status { QCA_WLAN_ROAM_STATS_FRAME_STATUS_SUCCESS = 0, QCA_WLAN_ROAM_STATS_FRAME_STATUS_FAIL = 1, }; /** * enum qca_wlan_vendor_attr_roam_stats_frame_info - Attributes used within the * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO nested attribute. */ enum qca_wlan_vendor_attr_roam_stats_frame_info { /* 8-bit unsigned value to indicate the frame subtype during * roaming, one of the values in qca_wlan_roam_stats_frame_subtype. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_SUBTYPE = 1, /* 8-bit unsigned value to indicate the frame is successful or failed * during roaming, one of the values in * qca_wlan_roam_stats_frame_status. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_STATUS = 2, /* 64-bit unsigned value to indicate the timestamp for frame of * preauthentication/reassociation/EAPOL-M1/EAPOL-M2/EAPOL-M3/EAPOL-M4 * when sent or received during roaming, timestamp in milliseconds * from system boot. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_TIMESTAMP = 3, /* This attribute indicates a 6-byte MAC address representing * the BSSID of the AP. * For non-MLO scenario, it indicates the AP BSSID. * For MLO scenario, it indicates the AP BSSID which may be the primary * link BSSID or a nonprimary link BSSID. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_BSSID = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_roam_stats_info - Used by the attribute * QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INFO. */ enum qca_wlan_vendor_attr_roam_stats_info { /* 64-bit unsigned value to indicate the timestamp when roam was * triggered by the firmware, timestamp in milliseconds from system * boot. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_TRIGGER_TIMESTAMP = 1, /* 32-bit unsigned value to indicate the roam trigger reason for the * last roaming attempted by the firmware. This can be queried either * in a connected state or disconnected state. The values of this * attribute represent the roam trigger reason codes, which * are defined in enum qca_roam_reason. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TRIGGER_REASON = 2, /* 8-bit unsigned value to indicate percentage of packets for which * the RX rate is lower than the RX rate threshold in total RX packets, * used for roaming trigger by per. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PER_RXRATE_THRESHOLD_PERCENT = 3, /* 8-bit unsigned value to indicate percentage of packets for which * the TX rate is lower than TX rate threshold in total TX packets, * used for roaming trigger by per. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PER_TXRATE_THRESHOLD_PERCENT = 4, /* 32-bit unsigned value to indicate final beacon miss count for * trigger reason of beacon miss. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FINAL_BMISS_CNT = 5, /* 32-bit unsigned value to indicate consecutive beacon miss count * for trigger reason of beacon miss. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONSECUTIVE_BMISS_CNT = 6, /* 8-bit unsigned value to indicate QOS-NULL TX status for trigger * reason of beacon miss, 0 - success, 1 - fail. * If QOS-NULL TX status is successful, beacon miss final count and * consecutive beacon miss count will be reset to zero, and roam will * not be triggered. If QOS-NULL TX status is failed, beacon miss final * count and consecutive beacon miss count continue to calculate until * roaming trigger by beacon miss. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BMISS_QOS_NULL_SUCCESS = 7, /* 8-bit signed value to indicate connected AP RSSI in dBm * for trigger reason of poor RSSI. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_POOR_RSSI_CURRENT_RSSI = 8, /* 8-bit signed value to indicate RSSI threshold value in dBm * for trigger reason of poor RSSI. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_POOR_RSSI_ROAM_RSSI_THRESHOLD = 9, /* 8-bit unsigned value to indicate RX link speed status * for trigger reason of poor RSSI, 0 - good link speed, * 1 - bad link speed. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_POOR_RSSI_RX_LINKSPEED_STATUS = 10, /* 8-bit signed value to indicate connected AP RSSI in dBm * for trigger reason of better RSSI. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BETTER_RSSI_CURRENT_RSSI = 11, /* 8-bit signed value to indicate RSSI threshold value in dBm * for trigger reason of better RSSI. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BETTER_RSSI_HIGH_RSSI_THRESHOLD = 12, /* 32-bit unsigned value to indicate RX throughput in bytes per second * for trigger reason of congestion. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONGESTION_RX_TPUT = 13, /* 32-bit unsigned value to indicate TX throughput in bytes per second * for trigger reason of congestion. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONGESTION_TX_TPUT = 14, /* 8-bit unsigned value to indicate roamable AP count * for trigger reason of congestion. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONGESTION_ROAMABLE_CNT = 15, /* 8-bit unsigned value to indicate invoke reason, one of the values * defined in qca_wlan_roam_stats_invoke_reason. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_USER_TRIGGER_INVOKE_REASON = 16, /* 8-bit unsigned value to indicate request mode for trigger reason * of BTM, values are defined in IEEE Std 802.11-2020, 9.6.13.9. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_REQUEST_MODE = 17, /* 32-bit unsigned value to indicate disassociate time in milliseconds * for trigger reason of BTM. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_DISASSOC_IMMINENT_TIME = 18, /* 32-bit unsigned value to indicate preferred candidate list valid * interval in milliseconds for trigger reason of BTM. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_VALID_INTERNAL = 19, /* 8-bit unsigned value to indicate the number of preferred * candidates for trigger reason of BTM. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_CANDIDATE_LIST_CNT = 20, /* 8-bit unsigned value to indicate response status for trigger * reason of BTM, values are defined in IEEE Std 802.11-2020, * Table 9-428 (BTM status code definitions). */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_RESPONSE_STATUS_CODE = 21, /* 32-bit unsigned value to indicate BSS termination timeout value * in milliseconds for trigger reason of BTM. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_BSS_TERMINATION_TIMEOUT = 22, /* 32-bit unsigned value to indicate MBO associate retry timeout * value in milliseconds for trigger reason of BTM. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_MBO_ASSOC_RETRY_TIMEOUT = 23, /* 8-bit unsigned value to indicate dialog token number * for trigger reason of BTM. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_REQ_DIALOG_TOKEN = 24, /* 8-bit unsigned value to indicate percentage of connected AP * channel congestion utilization for trigger reason of BSS load. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BSS_CU_LOAD = 25, /* 8-bit unsigned value to indicate disconnection type * for trigger reason of disconnection. 1 - Deauthentication, * 2 - Disassociation. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DISCONNECTION_TYPE = 26, /* 16-bit unsigned value to indicate deauthentication or disassociation * reason for trigger reason of disconnection, values are defined * in IEEE Std 802.11-2020, Table 9-49 (Reason codes). */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DISCONNECTION_REASON = 27, /* 32-bit unsigned value to indicate milliseconds of roam scan * periodicity when needing to roam to find a better AP for trigger * reason of periodic timer. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PERIODIC_TIMER_MS = 28, /* 8-bit signed value to indicate connected AP RSSI in dBm for * trigger reason of background scan. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BACKGROUND_SCAN_CURRENT_RSSI = 29, /* 8-bit signed value to indicate data RSSI in dBm for trigger reason * of background scan. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BACKGROUND_SCAN_DATA_RSSI = 30, /* 8-bit signed value to indicate data RSSI threshold in dBm * for trigger reason of background scan. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BACKGROUND_SCAN_DATA_RSSI_THRESH = 31, /* 32-bit unsigned value to indicate consecutive TX failure threshold * for trigger reason of TX failures. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TX_FAILURES_THRESHOLD = 32, /* 8-bit unsigned value to indicate TX failure reason for trigger * reason of TX failures, one of the values defined in * qca_wlan_roam_stats_tx_failures_reason. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TX_FAILURES_REASON = 33, /* 8-bit unsigned value to indicate detail abort reason. One of the * values in enum qca_wlan_roam_stats_abort_reason. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ABORT_REASON = 34, /* 8-bit signed value to indicate data RSSI in dBm when aborting the * roam scan. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DATA_RSSI = 35, /* 8-bit signed value to indicate data RSSI threshold in dBm when * aborting the roam scan. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DATA_RSSI_THRESHOLD = 36, /* 8-bit unsigned value to indicate data RSSI threshold in RX link * speed status when aborting the roam scan. * 0 - good link speed, 1 - bad link speed */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DATA_RX_LINKSPEED_STATUS = 37, /* 8-bit unsigned value to indicate roaming scan type. * One of the values in enum qca_wlan_roam_stats_scan_type. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_TYPE = 38, /* 8-bit unsigned value to indicate roaming result, used in STA mode * only. * 0-Roaming is successful, 1-Roaming is failed */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_STATUS = 39, /* 8-bit unsigned value to indicate the roam fail reason for the * last failed roaming attempt by the firmware. Different roam failure * reason codes are specified in enum qca_vendor_roam_fail_reasons. * This can be queried either in connected state or disconnected state. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FAIL_REASON = 40, /* Nested attribute. Indicate roam scan info for each channel, the * attributes defined in enum * qca_wlan_vendor_attr_roam_stats_scan_chan_info are used inside * this attribute. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_CHAN_INFO = 41, /* 32-bit unsigned value to indicate total scan time during roam scan * all channels, time in milliseconds. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TOTAL_SCAN_TIME = 42, /* Nested attribute. This attribute shall be used by the driver to * send roam information of each subtype. The attributes defined in * enum qca_wlan_vendor_attr_roam_stats_frame_info are used inside * this attribute. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO = 43, /* 6-byte MAC address used by the driver to send roam stats information * of the original AP BSSID. The original AP is the connected AP before * roam happens, regardless of the roam resulting in success or failure. * This attribute is only present when * QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_STATUS has a value of * 0 (success) or 1 (failure). * For non-MLO scenario, it indicates the original connected AP BSSID. * For MLO scenario, it indicates the original BSSID of the link * for which the reassociation occurred during the roam. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ORIGINAL_BSSID = 45, /* 6-byte MAC address used by the driver to send roam stats information * of the roam candidate AP BSSID when roam failed. This is only present * when QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_STATUS has a value of * 1 (failure). If the firmware updates more than one candidate AP BSSID * to the driver, the driver only fills the last candidate AP BSSID and * reports it to user space. * For non-MLO scenario, it indicates the last candidate AP BSSID. * For MLO scenario, it indicates the AP BSSID which may be the primary * link BSSID or a nonprimary link BSSID. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CANDIDATE_BSSID = 46, /* 6-byte MAC address used by the driver to send roam stats information * of the roamed AP BSSID when roam succeeds. This is only present when * QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_STATUS has a value of * 0 (success). * For non-MLO scenario, it indicates the new AP BSSID to which has * been successfully roamed. * For MLO scenario, it indicates the new AP BSSID of the link on * which the reassociation occurred during the roam. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAMED_BSSID = 47, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_STATS_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_STATS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_roam_cached_stats - Vendor subcmd attributes to * report cached roam info from the driver to user space, enum values are used * for netlink attributes sent with the * %QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS sub command. */ enum qca_wlan_vendor_attr_roam_cached_stats { QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INVALID = 0, /* Nested attribute, this attribute contains nested array roam info * statistics defined in enum qca_wlan_vendor_attr_roam_stats_info. */ QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INFO = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_CACHED_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_CACHED_STATS_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_CACHED_STATS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_supported_radio_cfg - Attributes for * radio configurations present in each radio combination. * * @QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_BAND: u32 attribute indicates * the band info in the radio configuration. Uses the enum qca_set_band values. * * @QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_ANTENNA: u8 attribute indicates * the number of antennas info in the radio configuration. */ enum qca_wlan_vendor_attr_supported_radio_cfg { QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_BAND = 1, QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_ANTENNA = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_LAST, QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_MAX = QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_LAST - 1, }; /** * enum qca_wlan_vendor_attr_radio_combination - Attributes for * radio combinations supported by the device. * * @QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_CFGS: Nested attribute * provides the radio configurations present in the radio combination. * Uses the enum qca_wlan_vendor_attr_supported_radio_cfg attributes. * This attribute provides the values for radio combination matrix. * For standalone config, the number of config values is one and the config * carries the band and antenna information for standalone configuration. For * Dual Band Simultaneous (DBS)/Single Band Simultaneous (SBS) mode * configuration the number of config values is two and the config carries the * band and antenna information for each simultaneous radio. */ enum qca_wlan_vendor_attr_radio_combination { QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_CFGS = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_LAST, QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_MAX = QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_LAST - 1, }; /** * enum qca_wlan_vendor_attr_radio_combination_matrix - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_GET_RADIO_COMBINATION_MATRIX * * @QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_SUPPORTED_CFGS: Nested attribute * provides the radio combinations supported by the device. * Uses the enum qca_wlan_vendor_attr_radio_combination attributes. * For example, in the radio combination matrix for a device which has two * radios, where one radio is capable of 2.4 GHz 2X2 only and another radio is * capable of either 5 GHz or 6 GHz 2X2, the possible number of radio * combinations is 5 and the radio combinations are * {{{2.4 GHz 2X2}}, //Standalone 2.4 GHz * {{5 GHz 2X2}}, //Standalone 5 GHz * {{6 GHz 2X2}}, //Standalone 6 GHz * {{2.4 GHz 2X2}, {5 GHz 2X2}}, //2.4 GHz + 5 GHz DBS * {{2.4 GHz 2X2}, {6 GHz 2X2}}} //2.4 GHz + 6 GHz DBS * The band and antenna info together as nested data provides one radio config. * Standalone configuration has one config with band and antenna nested data. * Dual Band Simultaneous (DBS)/Single Band Simultaneous (SBS) configuration * have two nested band and antenna info data. */ enum qca_wlan_vendor_attr_radio_combination_matrix { QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_INVALID = 0, QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_SUPPORTED_CFGS = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_LAST, QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_MAX = QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mdns_offload - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD vendor command. * * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENABLE: Required (flag) * Enable mDNS offload. This attribute is mandatory to enable * mDNS offload feature. If this attribute is not present, mDNS offload * is disabled. * * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_TABLE: Nested attribute containing * one or more %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY attributes. This * attribute is mandatory when enabling the feature, and not required when * disabling the feature. * * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY: Nested attribute containing * the following attributes: * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD * * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN: Required string attribute. * It consists of a hostname and ".local" as the domain name. The character * set is limited to UTF-8 encoding. The maximum allowed size is 63 bytes. * It is used to compare the domain the in the "QU" query. Only 1 FQDN is * supported per vdev. * For example: myphone.local * * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT: Required * u16 attribute. It specifies the total number of resource records present * in the answer section of the answer payload. This attribute is needed by the * firmware to populate the mDNS response frame for mNDS queries without having * to parse the answer payload. * * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD: Required Binary blob * attribute sent by the mdnsResponder from userspace. It contains resource * records of various types (Eg: A, AAAA, PTR, TXT) and service list. This * payload is passed down to firmware and is transmitted in response to * mDNS queries. * The maximum size of the answer payload supported is 512 bytes. */ enum qca_wlan_vendor_attr_mdns_offload { QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENABLE = 1, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_TABLE = 2, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY = 3, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN = 4, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT = 5, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_MAX = QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_AFTER_LAST - 1, }; /** * enum qca_vendor_attr_diag_event_type - Attributes used by * %QCA_WLAN_VENDOR_ATTR_DIAG_EVENT_TYPE attribute. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_CONNECTING: Diag event sent from * driver/firmware during Connection request from Userspace. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_SSID, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID_HINT, * QCA_WLAN_VENDOR_ATTR_DIAG_FREQ, * QCA_WLAN_VENDOR_ATTR_DIAG_FREQ_HINT, * QCA_WLAN_VENDOR_ATTR_DIAG_PAIRWISE_SUITE, * QCA_WLAN_VENDOR_ATTR_DIAG_GROUP_SUITE, * QCA_WLAN_VENDOR_ATTR_DIAG_AKM, * QCA_WLAN_VENDOR_ATTR_DIAG_AUTH_ALGO, * QCA_WLAN_VENDOR_ATTR_DIAG_GROUP_MGMT_SUITE, * QCA_WLAN_VENDOR_ATTR_DIAG_BT_COEX_ACTIVE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_CONNECTING_FAIL: Diag event sent from * driver/firmware when a connection is failed. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_FREQ, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_AUTH_REQ: Diag event sent from * driver/firmware during Authentication request from a device. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_AUTH_ALGO, * QCA_WLAN_VENDOR_ATTR_DIAG_SAE_AUTH_FRAME_TYPE, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_STATUS_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_AUTH_RESP: Diag event sent from * driver/firmware when device receives an authentication response. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_AUTH_ALGO, * QCA_WLAN_VENDOR_ATTR_DIAG_SAE_AUTH_FRAME_TYPE, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_STATUS_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ASSOC_REQ: Diag event sent from * driver/firmware when device sends an association request. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ASSOC_RESP: Diag event sent from * driver/firmware when device receives an association response. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_STATUS_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_ASSOC_ID. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DEAUTH_RX: Diag event sent from * driver/userspace when device receives a deauthentication response. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DEAUTH_TX: Diag event sent from * driver/userspace when device sends a deauthentication request. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DISASSOC_RX: Diag event sent from * driver/firmware when device receives a disassociation response. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DISASSOC_TX: Diag event sent from * driver/firmware when device sends a disassociation request. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BEACON_LOSS_DISCONN: Diag event sent from * driver/firmware when device did not receive beacon packets during connection. * Uses the following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCAN_START: Diag event sent from * driver/firmware when Roaming scan is triggered. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_REASON, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_SUB_REASON, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_CU, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCAN_TYPE, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_RSSI_THRESHOLD, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCAN_DONE: Diag event sent from * driver/firmware Roam scanning is processed. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_RANK, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_FREQ_LIST, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_COUNT, * QCA_WLAN_VENDOR_ATTR_DIAG_FREQ, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BT_COEX_ACTIVE. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCORE_CURR_AP: Diag event sent from * driver/firmware to provide Roam information of the current AP. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_FREQ, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_CU, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCORE, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCORE_CAND_AP: Diag event sent from * driver/firmware to provide Roam information of the candid AP. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_FREQ, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_CU, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCORE, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_ETP, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_RANK, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_RESULT: Diag event sent from * driver/firmware to provide Roam result after selecting a candidate. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SUCCESSFUL, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_CANCEL: Diag event sent from * driver/firmware to indicate Roam Cancellation due to higher priority events. * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_REQ: Diag event sent from driver * /firmware when STA sends a BTM request frame. Uses the following attributes * of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TOKEN, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_MODE, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_DISASSOC_TIMER, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_VALIDITY_INTERVAL, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_CANDIDATE_LIST_COUNT, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_QUERY: Diag event sent from * driver/firmware when STA queries about BTM transition. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TOKEN, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_QUERY_REASON, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_RESP: Diag event sent from driver * /firmware when STA receives BTM response frame. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TOKEN, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_STATUS_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_DELAY, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TARGET_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_REQ_CANDI: Diag event sent from * driver/firmware to provide BTM request candidate information. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_PREFERENCE, * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_RANK, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_WTC: Diag event sent from driver * /firmware when ROAM WTC trigger happens. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_WTC_SUB_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_BTM_WTC_DURATION, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_DISCOVER: Diag event sent from * driver/firmware to indicate DHCP discovery to AP. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_OFFER: Diag event sent from * driver/firmware to indicate DHCP offering to AP. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_REQUEST: Diag event sent from * driver/firmware to indicate driver sent DHCP packets. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_ACK: Diag event sent from driver * /firmware to indicate acknowledgement of DHCP packets. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_NACK: Diag event sent from driver * /firmware to indicate negative acknowledgement of DHCP packets. Uses the * following attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M1: Diag event sent from driver * /firmware to indicate EAPOL M1 message. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M2: Diag event sent from driver * /firmware to indicate EAPOL M2 message. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M3: Diag event sent from driver * /firmware to indicate EAPOL M3 message. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M4: Diag event sent from driver * /firmware to indicate EAPOL M4 message. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_GTK_M1: Diag event sent from driver * /firmware to indicate GTK rekey M1 frame. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_GTK_M2: Diag event sent from driver * /firmware to indicate GTK Rekey M2 frame. Uses the following attributes of * enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_REQUEST: Diag event sent from driver * /firmware to indicate device sent EAP request. Uses the following attributes * of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_EAP_TYPE, * QCA_WLAN_VENDOR_ATTR_DIAG_EAP_LEN, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_RESPONSE: Diag event sent from driver * /firmware to indicate device received EAP response. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_EAP_TYPE, * QCA_WLAN_VENDOR_ATTR_DIAG_EAP_LEN, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_SUCCESS: Diag event sent from driver * /firmware to indicate EAP frame transmission is success. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_FAILURE: Diag event sent from driver * /firmware to indicate EAP frame transmission is failed. Uses the following * attributes of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_REASSOC_REQ: Diag event sent from driver * /firmware to indicate Reassocation request. Uses the following attributes * of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_RSSI, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP. * * @QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_REASSOC_RES: Diag event sent from driver * /firmware to indicate Reassocation response. Uses the following attributes * of enum qca_wlan_vendor_attr_diag: * QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP, * QCA_WLAN_VENDOR_ATTR_DIAG_BSSID, * QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER, * QCA_WLAN_VENDOR_ATTR_DIAG_STATUS_CODE, * QCA_WLAN_VENDOR_ATTR_DIAG_ASSOC_ID, * QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX, * QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME, * QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP. */ enum qca_vendor_attr_diag_event_type { QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_CONNECTING = 0, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_CONNECTING_FAIL = 1, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_AUTH_REQ = 2, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_AUTH_RESP = 3, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ASSOC_REQ = 4, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ASSOC_RESP = 5, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DEAUTH_RX = 6, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DEAUTH_TX = 7, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DISASSOC_RX = 8, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DISASSOC_TX = 9, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BEACON_LOSS_DISCONN = 10, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCAN_START = 11, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCAN_DONE = 12, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCORE_CURR_AP = 13, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCORE_CAND_AP = 14, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_RESULT = 15, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_CANCEL = 16, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_REQ = 17, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_QUERY = 18, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_RESP = 19, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_REQ_CANDI = 20, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_BTM_WTC = 21, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_DISCOVER = 22, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_OFFER = 23, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_REQUEST = 24, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_ACK = 25, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_DHCP_NACK = 26, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M1 = 27, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M2 = 28, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M3 = 29, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAPOL_M4 = 30, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_GTK_M1 = 31, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_GTK_M2 = 32, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_REQUEST = 33, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_RESPONSE = 34, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_SUCCESS = 35, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_FAILURE = 36, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_REASSOC_REQ = 37, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_REASSOC_RES = 38, /* keep last */ QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_AFTER_LAST, QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_MAX = QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_tx_status - Used by attribute * QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS to indicate TX status. * @QCA_WLAN_VENDOR_TX_STATUS_FAIL: Indicates frame is not sent over the air. * @QCA_WLAN_VENDOR_TX_STATUS_NO_ACK: Indicates packet sent but acknowledgement * is not received. * @QCA_WLAN_VENDOR_TX_STATUS_ACK: Indicates the frame is successfully sent and * acknowledged. */ enum qca_wlan_vendor_tx_status { QCA_WLAN_VENDOR_TX_STATUS_FAIL = 1, QCA_WLAN_VENDOR_TX_STATUS_NO_ACK = 2, QCA_WLAN_VENDOR_TX_STATUS_ACK = 3, }; /** * enum qca_roam_sub_reason - Used by attribute * QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_SUB_REASON * @QCA_ROAM_SUB_REASON_PERIODIC_TIMER: Roam scan triggered due to periodic * timer expiry * @QCA_ROAM_SUB_REASON_INACTIVITY_TIMER_LOW_RSSI: Roam scan trigger due * to no candidate found during LOW RSSI trigger. * @QCA_ROAM_SUB_REASON_BTM_DI_TIMER: Roam scan triggered due to BTM Disassoc * Imminent timeout * @QCA_ROAM_SUB_REASON_FULL_SCAN: Roam scan triggered due to partial scan * failure * @QCA_ROAM_SUB_REASON_LOW_RSSI_PERIODIC: Roam trigger due to * emergency like deauth/disassoc. * @QCA_ROAM_SUB_REASON_CU_PERIODIC: Roam trigger due to * BSS transition management request. * @QCA_ROAM_SUB_REASON_PERIODIC_TIMER_AFTER_INACTIVITY_LOW_RSSI: * Roam scan triggered due to Low RSSI periodic timer * @QCA_ROAM_SUB_REASON_PERIODIC_TIMER_AFTER_INACTIVITY_CU: * Roam trigger due to periodic timer after no candidate found during CU * inactivity timer scan. * @QCA_ROAM_SUB_REASON_INACTIVITY_TIMER_CU: Roam trigger due to no candidate * found in high CU roam trigger. */ enum qca_roam_sub_reason { QCA_ROAM_SUB_REASON_PERIODIC_TIMER = 1, QCA_ROAM_SUB_REASON_INACTIVITY_TIMER_LOW_RSSI = 2, QCA_ROAM_SUB_REASON_BTM_DI_TIMER = 3, QCA_ROAM_SUB_REASON_FULL_SCAN = 4, QCA_ROAM_SUB_REASON_LOW_RSSI_PERIODIC = 5, QCA_ROAM_SUB_REASON_CU_PERIODIC = 6, QCA_ROAM_SUB_REASON_PERIODIC_TIMER_AFTER_INACTIVITY_LOW_RSSI = 7, QCA_ROAM_SUB_REASON_PERIODIC_TIMER_AFTER_INACTIVITY_CU = 8, QCA_ROAM_SUB_REASON_INACTIVITY_TIMER_CU = 9, }; /* * enum qca_wlan_vendor_attr_diag - Defines attributes used by the driver * to send diag data to the userspace. The attributes defined in this enum are * used with QCA_NL80211_VENDOR_SUBCMD_DIAG_DATA. * * @QCA_WLAN_VENDOR_ATTR_DIAG_EVENT: Required Attribute. Nested attribute used * by driver/firmware to send diag data. Each instance of this nested attribute * contains one QCA_WLAN_VENDOR_ATTR_DIAG_EVENT_TYPE attribute and other * attributes defined in enum qca_wlan_vendor_attr_diag that belong to the * event type defined by QCA_WLAN_VENDOR_ATTR_DIAG_EVENT_TYPE. Multiple of this * nested attribute can be sent with one vendor command * QCA_NL80211_VENDOR_SUBCMD_DIAG_DATA. * * @QCA_WLAN_VENDOR_ATTR_DIAG_EVENT_TYPE: Required u32 attribute. This * attribute indicates the type of the diag event from driver/firmware. Uses * values from enum qca_vendor_attr_diag_event_type. * * @QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP: Required u64 attribute. This * attribute indicates the system timestamp. Driver uses ktime_get_real_ts64() * API to send time of the day in microseconds to userspace. * * @QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP: Optional u64 attribute. * This attribute indicates firmware timestamp in microseconds. * * @QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX: Optional u8 attribute. This attribute * indicates wlan interface index. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BSSID: Optional attribute. This attribute * indicates 6-byte MAC address representing the BSSID of the AP. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BSSID_HINT: Optional attribute. This attribute * indicates the 6-byte MAC address representing the BSSID hint sent in * the connect request. * * @QCA_WLAN_VENDOR_ATTR_DIAG_SSID: Optional attribute. This attribute * indicates the SSID in u8 array with a maximum length of 32. * * @QCA_WLAN_VENDOR_ATTR_DIAG_FREQ: Optional u16 attribute. This attribute * indicates the frequency of AP in MHz. * * @QCA_WLAN_VENDOR_ATTR_DIAG_FREQ_HINT: Optional u16 attribute. This attribute * indicates frequency hint given in the connect request in MHz. * * @QCA_WLAN_VENDOR_ATTR_DIAG_RSSI: Optional signed 32 attribute. * This attribute indicates RSSI of the 802.11 frame in dBm. * * @QCA_WLAN_VENDOR_ATTR_DIAG_PAIRWISE_SUITE: Optional u32 attribute. * This attribute indicates Pairwise cipher suite defined in IEEE 802.11 2020 * Table 12-10—Integrity and key wrap algorithms. * * @QCA_WLAN_VENDOR_ATTR_DIAG_GROUP_SUITE: Optional u32 attribute. * This attribute indicates Group cipher suite defined in IEEE 802.11 2020 * Table 12-10—Integrity and key wrap algorithms. * * @QCA_WLAN_VENDOR_ATTR_DIAG_GROUP_MGMT_SUITE: Optional u32 attribute. This * attribute indicates Group management cipher suite defined in IEEE Std * 802.11‐2020 spec. Table 12-10—Integrity and key wrap algorithms. * * @QCA_WLAN_VENDOR_ATTR_DIAG_AKM: Optional u32 attribute. This attribute * indicates Auth key management suite defined in IEEE Std 802.11‐2020 * Table 9-151—AKM suite selectors. * * @QCA_WLAN_VENDOR_ATTR_DIAG_AUTH_ALGO: Optional u8 attribute. This attribute * indicates authentication algorithm number defined in IEEE Std 802.11‐2020 * Section 9.4.1.1 Authentication Algorithm Number field. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BT_COEX_ACTIVE: Optional flag. This attribute * indicates bluetooth COEX is active or not. * * @QCA_WLAN_VENDOR_ATTR_DIAG_SAE_AUTH_FRAME_TYPE: Optional u8 attribute. This * attribute indicates SAE authentication frame type. The possible values are * 1 - SAE commit frame * 2 - SAE confirm frame * * @QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE: Optional u16 attribute. This * attribute indicates the reason codes defined in IEEE Std 802.11‐2020 * Table 9-49—Reason codes. * * @QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER: Optional u16 attribute. This * attribute indicates sequence number of the frame defined in IEEE Std * 802.11‐2020 Section 9.4.1.2 Authentication Transaction Sequence Number * field. * * @QCA_WLAN_VENDOR_ATTR_DIAG_STATUS_CODE: Optional u8 attribute. This * attribute indicates the status codes defined in IEEE Std 802.11‐2020 Table * 9-50—Status codes. * * @QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS: Optional u8 attribute. * Uses enum qca_wlan_vendor_tx_status. * * @QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME: Optional flag. This attribute * indicates if frame transmission is retried. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_REASON: Optional u8 attribute. * Uses enum qca_roam_reason. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_SUB_REASON: Optional u8 attribute. * Uses enum qca_roam_sub_reason. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_CU: Optional u8 attribute. This attribute * indicates channel utilization in percentage. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCAN_TYPE: Optional u8 attribute. This * attribute indicates scan type used. Uses enum qca_roam_scan_scheme. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_RSSI_THRESHOLD: Optional signed 32 attribute. * This attribute indicates current RSSI threshold in dBm. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_FREQ_LIST: Required Attribute. * Nested attribute used by QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCAN_DONE * to carry list of QCA_WLAN_VENDOR_ATTR_DIAG_FREQ. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_COUNT: optional u8 attribute. * This attribute indicates number of scanned candidate APs. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_RANK: Optional u8 attribute. This * attribute indicates roam AP rank computed based on connection preference. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_ETP: Optional u32 attribute. * This attribute indicates expected throughput in kbps. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCORE: Optional u16 attribute. * This attribute indicates the preference value of candidate AP / connected AP * calculated in the firmware. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SUCCESSFUL: Optional flag. This attribute * indicates connection/roaming is successful or not. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_WTC_SUB_REASON_CODE: Optional u8 attribute. * This attribute indicates BTM WTC sub reason code in the WTC vendor specific * IE present in the BTM frame. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_WTC_DURATION: Optional u32 attribute. * This attribute indicates BTM WTC duration in milliseconds. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TOKEN: Optional u8 attribute. This attribute * indicates dialog token value of BTM query/request/response frames. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_QUERY_REASON: Optional u8 attribute. This * attribute indicates the Transition Reason field indicates the reason why * a transition attempt occurred and contains one of the values defined in IEEE * Std 802.11‐2020 Table 9-198—Transition and Transition Query reasons. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_MODE: Optional u8 attribute. This attribute * indicates BTM mode defined in IEEE Std 802.11‐2020 * Figure 9-924—Request Mode field format. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_DISASSOC_TIMER: Optional u16 attribute. * This attribute indicates the Disassociation Timer field which is the number * of beacon transmission times (TBTTs) until the serving AP will send a * Disassociation frame to this STA. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_VALIDITY_INTERVAL: Optional u8 attribute. * This attribute indicates BTM validity interval field in TBTTs defined in * IEEE Std 802.11‐2020 Figure 9-923—BSS Transition Management Request frame * Action field format. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_CANDIDATE_LIST_COUNT: Optional u8 attribute. * This attribute indicates BTM candidate list entries. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_PREFERENCE: Optional u8 attribute. * This attribute indicates network preference for BTM transition defined in * IEEE Std 802.11‐2020 Table 9-174—Preference field values. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_STATUS_CODE: Optional u8 attribute. * This attribute indicates BTM transition status code defined in IEEE Std * 802.11‐2020 Table 9-428—BTM status code definitions. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_DELAY: Optional u8 attribute. * This attribute indicates BSS termination delay defined in IEEE Std * 802.11‐2020 Section 9.6.13.10 BSS Transition Management Response frame format. * * @QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TARGET_BSSID: Optional attribute. * This attribute indicates 6-byte MAC address representing the BSSID of the * BSS that the non-AP STA transitions to. * * @QCA_WLAN_VENDOR_ATTR_DIAG_EAP_TYPE: Optional u8 attribute. This attribute * indicates EAP frame type. The methods are enumerated by IANA at * https://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml. * * @QCA_WLAN_VENDOR_ATTR_DIAG_EAP_LEN: Optional u8 attribute. This attribute * indicates EAP frame length. * * @QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP: Required u64 attribute. This * attribute indicates the kernel timestamp. Driver uses ktime_get() API * (Time from boot but not the time spent in suspend) to send in microseconds * to userspace. * * @QCA_WLAN_VENDOR_ATTR_DIAG_ASSOC_ID: Optional u16 attribute. This attribute * indicates the association id received in the (re)association response frame * defined in IEEE Std 802.11-2020 Figure 9-91-AID field format. */ enum qca_wlan_vendor_attr_diag { QCA_WLAN_VENDOR_ATTR_DIAG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DIAG_EVENT = 1, QCA_WLAN_VENDOR_ATTR_DIAG_EVENT_TYPE = 2, QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP = 3, QCA_WLAN_VENDOR_ATTR_DIAG_FIRMWARE_TIMESTAMP = 4, QCA_WLAN_VENDOR_ATTR_DIAG_IFINDEX = 5, QCA_WLAN_VENDOR_ATTR_DIAG_BSSID = 6, QCA_WLAN_VENDOR_ATTR_DIAG_BSSID_HINT = 7, QCA_WLAN_VENDOR_ATTR_DIAG_SSID = 8, QCA_WLAN_VENDOR_ATTR_DIAG_FREQ = 9, QCA_WLAN_VENDOR_ATTR_DIAG_FREQ_HINT = 10, QCA_WLAN_VENDOR_ATTR_DIAG_RSSI = 11, QCA_WLAN_VENDOR_ATTR_DIAG_PAIRWISE_SUITE = 12, QCA_WLAN_VENDOR_ATTR_DIAG_GROUP_SUITE = 13, QCA_WLAN_VENDOR_ATTR_DIAG_GROUP_MGMT_SUITE = 14, QCA_WLAN_VENDOR_ATTR_DIAG_AKM = 15, QCA_WLAN_VENDOR_ATTR_DIAG_AUTH_ALGO = 16, QCA_WLAN_VENDOR_ATTR_DIAG_BT_COEX_ACTIVE = 17, QCA_WLAN_VENDOR_ATTR_DIAG_SAE_AUTH_FRAME_TYPE = 18, QCA_WLAN_VENDOR_ATTR_DIAG_REASON_CODE = 19, QCA_WLAN_VENDOR_ATTR_DIAG_SEQUENCE_NUMBER = 20, QCA_WLAN_VENDOR_ATTR_DIAG_STATUS_CODE = 21, QCA_WLAN_VENDOR_ATTR_DIAG_FRAME_TX_STATUS = 22, QCA_WLAN_VENDOR_ATTR_DIAG_IS_RETRY_FRAME = 23, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_REASON = 24, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_TRIGGER_SUB_REASON = 25, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_CU = 26, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCAN_TYPE = 27, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_RSSI_THRESHOLD = 28, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_FREQ_LIST = 29, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_COUNT = 30, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_RANK = 31, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_AP_ETP = 32, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SCORE = 33, QCA_WLAN_VENDOR_ATTR_DIAG_ROAM_SUCCESSFUL = 34, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_WTC_SUB_REASON_CODE = 35, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_WTC_DURATION = 36, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TOKEN = 37, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_QUERY_REASON = 38, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_MODE = 39, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_DISASSOC_TIMER = 40, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_VALIDITY_INTERVAL = 41, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_CANDIDATE_LIST_COUNT = 42, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_PREFERENCE = 43, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_STATUS_CODE = 44, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_DELAY = 45, QCA_WLAN_VENDOR_ATTR_DIAG_BTM_TARGET_BSSID = 46, QCA_WLAN_VENDOR_ATTR_DIAG_EAP_TYPE = 47, QCA_WLAN_VENDOR_ATTR_DIAG_EAP_LEN = 48, QCA_WLAN_VENDOR_ATTR_DIAG_KERNEL_TIMESTAMP = 49, QCA_WLAN_VENDOR_ATTR_DIAG_ASSOC_ID = 50, /* keep last */ QCA_WLAN_VENDOR_ATTR_DIAG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DIAG_MAX = QCA_WLAN_VENDOR_ATTR_DIAG_AFTER_LAST - 1, }; /** * qca_wlan_vendor_monitor_data_frame_type - Represent the various * data types to be sent over the monitor interface. */ enum qca_wlan_vendor_monitor_data_frame_type { QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ALL = BIT(0), /* valid only if QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ALL is not set */ QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ARP = BIT(1), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DHCPV4 = BIT(2), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DHCPV6 = BIT(3), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_EAPOL = BIT(4), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DNSV4 = BIT(5), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DNSV6 = BIT(6), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_SYN = BIT(7), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_SYNACK = BIT(8), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_FIN = BIT(9), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_FINACK = BIT(10), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_ACK = BIT(11), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_RST = BIT(12), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ICMPV4 = BIT(13), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ICMPV6 = BIT(14), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_RTP = BIT(15), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_SIP = BIT(16), QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_QOS_NULL = BIT(17), }; /** * qca_wlan_vendor_monitor_mgmt_frame_type - Represent the various * mgmt types to be sent over the monitor interface. * @QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL: All the MGMT Frames. * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_NO_BEACON: All the MGMT Frames * except the Beacons. Valid only in the Connect state. * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_BEACON: Only the connected * BSSID Beacons. Valid only in the Connect state. * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_SCAN_BEACON: Represents * the Beacons obtained during the scan (off channel and connected channel) * when in connected state. */ enum qca_wlan_vendor_monitor_mgmt_frame_type { QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL = BIT(0), /* valid only if QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL is not set */ QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_NO_BEACON = BIT(1), QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_BEACON = BIT(2), QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_SCAN_BEACON = BIT(3), }; /** * qca_wlan_vendor_monitor_ctrl_frame_type - Represent the various * ctrl types to be sent over the monitor interface. * @QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL: All the ctrl Frames. * @QCA_WLAN_VENDOR_MONITOR_CTRL_TRIGGER_FRAME: Trigger Frame. */ enum qca_wlan_vendor_monitor_ctrl_frame_type { QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL = BIT(0), /* valid only if QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL is not set */ QCA_WLAN_VENDOR_MONITOR_CTRL_TRIGGER_FRAME = BIT(1), }; /** * enum qca_wlan_vendor_attr_set_monitor_mode - Used by the * vendor command QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE to set the * monitor mode. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_TX_FRAME_TYPE: u32 attribute, * Represents the tx data packet type to be monitored (u32). These data packets * are represented by enum qca_wlan_vendor_monitor_data_frame_type. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_RX_FRAME_TYPE: u32 attribute, * Represents the tx data packet type to be monitored (u32). These data packets * are represented by enum qca_wlan_vendor_monitor_data_frame_type. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_TX_FRAME_TYPE: u32 attribute, * Represents the tx data packet type to be monitored (u32). These mgmt packets * are represented by enum qca_wlan_vendor_monitor_mgmt_frame_type. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_RX_FRAME_TYPE: u32 attribute, * Represents the tx data packet type to be monitored (u32). These mgmt packets * are represented by enum qca_wlan_vendor_monitor_mgmt_frame_type. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_TX_FRAME_TYPE: u32 attribute, * Represents the tx data packet type to be monitored (u32). These ctrl packets * are represented by enum qca_wlan_vendor_monitor_ctrl_frame_type. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_RX_FRAME_TYPE: u32 attribute, * Represents the tx data packet type to be monitored (u32). These ctrl packets * are represented by enum qca_wlan_vendor_monitor_ctrl_frame_type. * * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CONNECTED_BEACON_INTERVAL: * u32 attribute, An interval only for the connected beacon interval, which * expects that the connected BSSID's beacons shall be sent on the monitor * interface only on this specific interval. */ enum qca_wlan_vendor_attr_set_monitor_mode { QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_TX_FRAME_TYPE = 1, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_RX_FRAME_TYPE = 2, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_TX_FRAME_TYPE = 3, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_RX_FRAME_TYPE = 4, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_TX_FRAME_TYPE = 5, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_RX_FRAME_TYPE = 6, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CONNECTED_BEACON_INTERVAL = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MAX = QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_roam_scan_state - Roam scan state flags. * Bits will be set to 1 if the corresponding state is enabled. * * @QCA_VENDOR_WLAN_ROAM_SCAN_STATE_START: Scan Start. * @QCA_VENDOR_WLAN_ROAM_SCAN_STATE_END: Scan end. */ enum qca_wlan_vendor_roam_scan_state { QCA_WLAN_VENDOR_ROAM_SCAN_STATE_START = BIT(0), QCA_WLAN_VENDOR_ROAM_SCAN_STATE_END = BIT(1), }; /** * enum qca_wlan_vendor_roam_event_type - Roam event type flags. * Bits will be set to 1 if the corresponding event is notified. * * @QCA_WLAN_VENDOR_ROAM_EVENT_TRIGGER_REASON: Represents that the roam event * carries the trigger reason. When set, it is expected that the roam event * carries the respective reason via the attribute * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON. This event also carries * the BSSID, RSSI, frequency info of the AP to which the roam is attempted. * * @QCA_WLAN_VENDOR_ROAM_EVENT_FAIL_REASON: Represents that the roam event * carries the roam fail reason. When set, it is expected that the roam event * carries the respective reason via the attribute * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_FAIL_REASON. This event also carries the * BSSID, RSSI, frequency info of the AP to which the roam was attempted. * * @QCA_WLAN_VENDOR_ROAM_EVENT_INVOKE_FAIL_REASON: Represents that the roam * event carries the roam invoke fail reason. When set, it is expected that * the roam event carries the respective reason via the attribute * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON. * * @QCA_WLAN_VENDOR_ROAM_EVENT_SCAN_STATE: Represents that the roam event * carries the roam scan state. When set, it is expected that the roam event * carries the respective scan state via the attribute * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE and the corresponding * frequency info via QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST. */ enum qca_wlan_vendor_roam_event_type { QCA_WLAN_VENDOR_ROAM_EVENT_TRIGGER_REASON = BIT(0), QCA_WLAN_VENDOR_ROAM_EVENT_FAIL_REASON = BIT(1), QCA_WLAN_VENDOR_ROAM_EVENT_INVOKE_FAIL_REASON = BIT(2), QCA_WLAN_VENDOR_ROAM_EVENT_ROAM_SCAN_STATE = BIT(3), }; /** * enum qca_wlan_vendor_attr_roam_events_candidate_info: Roam candidate info. * Referred by QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_BSSID: 6-byte MAC address * representing the BSSID of the AP to which the Roam is attempted. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_RSSI: Signed 32-bit value * in dBm, signifying the RSSI of the candidate BSSID to which the Roaming is * attempted. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ: u32, Frequency in MHz * on which the roam is attempted. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FAIL_REASON: u32, used in * STA mode only. This represents the roam fail reason for the last failed * roaming attempt by the firmware for the specific BSSID. Different roam * failure reason codes are specified in enum qca_vendor_roam_fail_reasons. */ enum qca_wlan_vendor_attr_roam_events_candidate_info { QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_BSSID = 1, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_RSSI = 2, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ = 3, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FAIL_REASON = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_roam_events - Used by the * vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS to either configure the * roam events to the driver or notify these events from the driver. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CONFIGURE: u8 attribute. Configures the * driver/firmware to enable/disable the notification of roam events. It's a * mandatory attribute and used only in the request from the userspace to the * host driver. 1-Enable, 0-Disable. * If the roaming is totally offloaded to the firmware, this request when * enabled shall mandate the firmware to notify all the relevant roam events * represented by the below attributes. If the host is in the suspend mode, * the behavior of the firmware to notify these events is guided by * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_DEVICE_STATE, and if the request is to get * these events in the suspend state, the firmware is expected to wake up the * host before the respective events are notified. Please note that such a * request to get the events in the suspend state will have a definite power * implication. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_SUSPEND_STATE: flag attribute. Represents * that the roam events need to be notified in the suspend state too. By * default, these roam events are notified in the resume state. With this flag, * the roam events are notified in both resume and suspend states. * This attribute is used in the request from the userspace to the host driver. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TYPE: u32, used in STA mode only. * Represents the different roam event types, signified by the enum * qca_wlan_vendor_roam_event_type. * Each bit of this attribute represents the different roam even types reported * through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON: u32, used in STA * mode only. This represents the roam trigger reason for the last roaming * attempted by the firmware. Each bit of this attribute represents the * different roam trigger reason code which are defined in enum * qca_vendor_roam_triggers. * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON: u32, used in * STA mode only. This represents the roam invoke fail reason for the last * failed roam invoke. Different roam invoke failure reason codes * are specified in enum qca_vendor_roam_invoke_fail_reasons. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO: Array of candidates info * for which the roam is attempted. Each entry is a nested attribute defined * by enum qca_wlan_vendor_attr_roam_events_candidate_info. * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE: u8 attribute. Represents * the scan state on which the roam events need to be notified. The values for * this attribute are referred from enum qca_wlan_vendor_roam_scan_state. * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. * * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST: Nested attribute of * u32 values. List of frequencies in MHz considered for a roam scan. * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. */ enum qca_wlan_vendor_attr_roam_events { QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CONFIGURE = 1, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_SUSPEND_STATE = 2, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TYPE = 3, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON = 4, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON = 5, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO = 6, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE = 7, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST = 8, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_AFTER_LAST - 1, }; /* * enum qca_wlan_ratemask_params_type - Rate mask config type. * * @QCA_WLAN_RATEMASK_PARAMS_TYPE_CCK_OFDM: CCK_OFDM rate mask config * @QCA_WLAN_RATEMASK_PARAMS_TYPE_HT: HT rate mask config * @QCA_WLAN_RATEMASK_PARAMS_TYPE_VHT: VHT rate mask config * @QCA_WLAN_RATEMASK_PARAMS_TYPE_HE: HE rate mask config */ enum qca_wlan_ratemask_params_type { QCA_WLAN_RATEMASK_PARAMS_TYPE_CCK_OFDM = 0, QCA_WLAN_RATEMASK_PARAMS_TYPE_HT = 1, QCA_WLAN_RATEMASK_PARAMS_TYPE_VHT = 2, QCA_WLAN_RATEMASK_PARAMS_TYPE_HE = 3, }; /* enum qca_wlan_vendor_attr_ratemask_params - Used by the * vendor command QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG. * This is used to set the rate mask value to be used in rate selection. * * @QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_LIST: * Array of nested containing attributes * QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_TYPE and * QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_BITMAP. * * @QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_TYPE: u8, represents * the different phy types to which the rate mask config is to be applied. * The values for this attribute are referred from enum * qca_wlan_vendor_ratemask_params_type. * * @QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_BITMAP: binary, rate mask bitmap. * A bit value of 1 represents rate is enabled and a value of 0 * represents rate is disabled. * For HE targets, 12 bits correpond to one NSS setting. * b0-13 => NSS1, MCS 0-13 * b14-27 => NSS2, MCS 0-13 and so on for other NSS. * For VHT targets, 10 bits correspond to one NSS setting. * b0-9 => NSS1, MCS 0-9 * b10-19 => NSS2, MCS 0-9 and so on for other NSS. * For HT targets, 8 bits correspond to one NSS setting. * b0-7 => NSS1, MCS 0-7 * b8-15 => NSS2, MCS 0-7 and so on for other NSS. * For OFDM/CCK targets, 8 bits correspond to one NSS setting. */ enum qca_wlan_vendor_attr_ratemask_params { QCA_WLAN_VENDOR_ATTR_RATEMASK_INVALID = 0, QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_LIST = 1, QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_TYPE = 2, QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_BITMAP = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_flush_pending_policy: Represents values for * the policy to flush pending frames, configured via * %QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING. This enumeration defines the * valid values for %QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_POLICY. * * @QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_NONE: This value clears all * the flush policy configured before. This command basically disables the * flush config set by the user. * @QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_IMMEDIATE: This value configures * the flush policy to be immediate. All pending packets for the peer/TID are * flushed when this command/policy is received. * @QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_TWT_SP_END: This value configures * the flush policy to the end of TWT SP. All pending packets for the peer/TID * are flushed when the end of TWT SP is reached. */ enum qca_wlan_vendor_flush_pending_policy { QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_NONE = 0, QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_IMMEDIATE = 1, QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_TWT_SP_END = 2, }; /** * enum qca_wlan_vendor_attr_flush_pending - Attributes for * flushing pending traffic in firmware. * * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address. * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK, * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to * flush packets with access category. This is optional. See below. * @QCA_WLAN_VENDOR_ATTR_TID_MASK: Configure TID mask of the pending packets. * It is a u32 value with bit 0-7 representing TID 0-7. Set corresponding * bit to 1 to act upon the TID. This is optional. Either this attribute or * %QCA_WLAN_VENDOR_ATTR_AC must be provided. If both are provided, * %QCA_WLAN_VENDOR_ATTR_TID_MASK takes precedence. If neither are provided * it is an error. * @QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_POLICY: Policy of flushing the pending * packets corresponding to the peer/TID provided. It is a u32 value, * represented by %enum qca_wlan_vendor_flush_pending_policy. This * value is honored only when TID mask is provided. This is not honored when AC * mask is provided. */ enum qca_wlan_vendor_attr_flush_pending { QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1, QCA_WLAN_VENDOR_ATTR_AC = 2, QCA_WLAN_VENDOR_ATTR_TID_MASK = 3, QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_POLICY = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX = QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_pasn_action - Action to authenticate (and generate keys * for) or drop existing PASN security association for the listed the * peers. Used by QCA_WLAN_VENDOR_ATTR_PASN_ACTION and sent from the driver * to userspace. * * @QCA_WLAN_VENDOR_PASN_ACTION_AUTH: Initiate PASN handshake with the peer * devices indicated with %QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR. * @QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT: Indication from * the driver to userspace to inform that the existing PASN keys of the * peer devices specified with %QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR are * not valid anymore. */ enum qca_wlan_vendor_pasn_action { QCA_WLAN_VENDOR_PASN_ACTION_AUTH, QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT, }; /** * enum qca_wlan_vendor_attr_pasn_peer: Defines the nested attributes used in * QCA_WLAN_VENDOR_ATTR_PASN_PEERS. * * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_SRC_ADDR: This attribute is optional in the * event from the driver to userspace and represents the local MAC address * to be used for PASN handshake. When this attribute is present, userspace * shall use the source address specified in this attribute by the driver * for PASN handshake with peer device. * This attribute is required in a command response from userspace to the * driver and represents the MAC address that was used in PASN handshake * with the peer device. * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR: Indicates the MAC address of the * peer device to which PASN handshake is requested in an event from the * driver to userspace when QCA_WLAN_VENDOR_ATTR_PASN_ACTION is set to * QCA_WLAN_VENDOR_PASN_ACTION_AUTH. * Indicates the MAC address of the peer device for which the keys are to * be invalidated in an event from the driver to userspace when * QCA_WLAN_VENDOR_ATTR_PASN_ACTION is set to * QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT. * Indicates the MAC address of the peer device for which the status is * being sent in a status report from userspace to the driver. * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_LTF_KEYSEED_REQUIRED: NLA_FLAG attribute used * in the event from the driver to userspace. When set, userspace is * required to derive LTF key seed from KDK and set it to the driver. * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_STATUS_SUCCESS: NLA_FLAG attribute. This * attribute is used in the command response from userspace to the driver. * If present, it indicates the successful PASN handshake with the peer. If * this flag is not present, it indicates that the PASN handshake with the * peer device failed. */ enum qca_wlan_vendor_attr_pasn_peer { QCA_WLAN_VENDOR_ATTR_PASN_PEER_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PASN_PEER_SRC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR = 2, QCA_WLAN_VENDOR_ATTR_PASN_PEER_LTF_KEYSEED_REQUIRED = 3, QCA_WLAN_VENDOR_ATTR_PASN_PEER_STATUS_SUCCESS = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_PASN_PEER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAX = QCA_WLAN_VENDOR_ATTR_PASN_PEER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_pasn: Defines the attributes used in the * QCA_NL80211_VENDOR_SUBCMD_PASN command. * * @QCA_WLAN_VENDOR_ATTR_PASN_ACTION: u32 attribute, possible values are * defined in enum qca_wlan_vendor_pasn_action and used only in an event * from the driver to userspace. * @QCA_WLAN_VENDOR_ATTR_PASN_PEERS: Nested attribute, used to pass PASN peer * details for each peer and used in both an event and a command response. * The nested attributes used inside QCA_WLAN_VENDOR_ATTR_PASN_PEERS are * defined in enum qca_wlan_vendor_attr_pasn_peer. */ enum qca_wlan_vendor_attr_pasn { QCA_WLAN_VENDOR_ATTR_PASN_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PASN_ACTION = 1, QCA_WLAN_VENDOR_ATTR_PASN_PEERS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_PASN_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PASN_MAX = QCA_WLAN_VENDOR_ATTR_PASN_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_secure_ranging_ctx_action - Used to add or delete * the ranging security context derived from PASN for each peer. Used in * QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_ACTION. * * @QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_ADD: Add the secure ranging * context for the peer. * @QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_DELETE: Delete the secure ranging * context for the peer. */ enum qca_wlan_vendor_secure_ranging_ctx_action { QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_ADD, QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_DELETE, }; /** * enum qca_wlan_vendor_sha_type - SHA types. Used to configure the SHA type * used for deriving PASN keys to the driver. Used in * QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE * @QCA_WLAN_VENDOR_SHA_256: SHA-256 * @QCA_WLAN_VENDOR_SHA_384: SHA-384 */ enum qca_wlan_vendor_sha_type { QCA_WLAN_VENDOR_SHA_256, QCA_WLAN_VENDOR_SHA_384, }; /** * enum qca_wlan_vendor_attr_secure_ranging_ctx: Defines the attributes used * to set security context for the PASN peer from userspace to the driver. * Used with QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT. * * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_ACTION: u32 attribute, possible * values are defined in enum qca_wlan_vendor_secure_ranging_ctx_action * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SRC_ADDR: The local MAC address that * was used during the PASN handshake. * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_PEER_MAC_ADDR: The MAC address of * the peer device for which secure ranging context is being configured. * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE: u32 attribute, defines the * hash algorithm to be used, possible values are defined in enum * qca_wlan_vendor_sha_type. * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_TK: Variable length attribute, holds * the temporal key generated from the PASN handshake. The length of this * attribute is dependent on the value of * %QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_CIPHER. * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_CIPHER: cipher suite to use with the * TK, u32, as defined in IEEE Std 802.11-2020, 9.4.2.24.2 (Cipher suites) * (e.g., 0x000FAC04). * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_LTF_KEYSEED: Variable length * attribute, holds the LTF keyseed derived from KDK of PASN handshake. * The length of this attribute is dependent on the value of * %QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE. * */ enum qca_wlan_vendor_attr_secure_ranging_ctx { QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_ACTION = 1, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SRC_ADDR = 2, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_PEER_MAC_ADDR = 3, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE = 4, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_TK = 5, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_CIPHER = 6, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_LTF_KEYSEED = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_MAX = QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_coap_offload_filter - Attributes used * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER * nested attribute. The packets that match a filter will be replied with * attributes configured in %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4: * u32 attribute. Destination IPv4 address in network byte order, the * IPv4 packets with different address will be filtered out. * This attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4_IS_BC: * Flag attribute. If it's present, indicates that * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4 is a broadcast * address; while if not, indicates that the address is a unicast/multicast * address. * This attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV6: * NLA_BINARY attribute, length is 16 bytes. * Destination IPv6 address in network byte order, the IPv6 packets * with different destination address will be filtered out. * This attribute is optional. * * At least one of %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4 and * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV6 must be configured. * Packets on both IPv4 and IPv6 will be processed if both are configured. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_PORT: * u16 attribute. Destination UDP port, the packets with different destination * UDP port will be filtered out. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_OFFSET: * u32 attribute. Represents the offset (in UDP payload) of the data * to be matched. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_DATA: * NLA_BINARY attribute, the maximum allowed size is 16 bytes. * Binary data that is compared bit-by-bit against the data (specified * by %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_OFFSET) in UDP * payload, the packets don't match will be filtered out. * This attribute is mandatory. */ enum qca_wlan_vendor_attr_coap_offload_filter { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4 = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4_IS_BC = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV6 = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_PORT = 4, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_OFFSET = 5, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_DATA = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_coap_offload_reply - Attributes used * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY nested attribute. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV4: * u32 attribute. Source address (in network byte order) for replying * the matching broadcast/multicast IPv4 packets. * This attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV6: * NLA_BINARY attribute, length is 16 bytes. * Source address (in network byte order) for replying the matching * multicast IPv6 packets. * This attribute is optional. * * For broadcast/multicast offload reply, one of * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV4 and * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV6 or both must be * configured according to version of the IP address(es) configured in * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER; * while for unicast case, firmware will take the destination IP address * in the received matching packet as the source address for replying. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER: * Nested attribute. Filter for the received UDP packets, only the matching * packets will be replied and cached. * See enum qca_wlan_vendor_attr_coap_offload_filter for list of supported * attributes. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_MSG: * NLA_BINARY attribute, the maximum allowed size is 1152 bytes. * CoAP message (UDP payload) to be sent upon receiving matching packets. * Firmware is responsible for adding any necessary protocol headers. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_CACHE_EXPTIME: * u32 attribute. Expiration time in milliseconds of the cached CoAP messages. * A cached message will be dropped by firmware if it's expired. * This attribute is optional. A default value of 40000 will be used in the * absence of it. */ enum qca_wlan_vendor_attr_coap_offload_reply { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV4 = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV6 = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_MSG = 4, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_CACHE_EXPTIME = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_coap_offload_tx_ipv4 - Represents parameters for * CoAP message (UDP) transmitting on IPv4. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_ADDR: * u32 attribute. Source address (in network byte order) for transmitting * packets on IPv4. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_PORT: * u16 attribute. Source UDP port. * This attribute is optional, a random port is taken if it's not present. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_ADDR: * u32 attribute. Destination IPv4 address (in network byte order). * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_IS_BC: * Flag attribute. If it's present, indicates that * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_ADDR is a broadcast * address; while if not, indicates that the address is unicast/multicast * address. * This attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_PORT: * u16 attribute. Destination UDP port. * This attribute is mandatory. */ enum qca_wlan_vendor_attr_coap_offload_tx_ipv4 { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_PORT = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_ADDR = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_IS_BC = 4, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_PORT = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_coap_offload_tx_ipv6 - Represents parameters for * CoAP message (UDP) transmitting on IPv6. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_ADDR: * NLA_BINARY attribute, length is 16 bytes. * Source address (in network byte order) for transmitting packets on IPv6. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_PORT: * u16 attribute. Source UDP port. * This attribute is optional, a random port is taken if it's not present. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_ADDR: * NLA_BINARY attribute, length is 16 bytes. * Destination IPv6 address (in network byte order). * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_PORT: * u16 attribute. Destination UDP port. * This attribute is mandatory. */ enum qca_wlan_vendor_attr_coap_offload_tx_ipv6 { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_PORT = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_ADDR = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_PORT = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_coap_offload_periodic_tx - Attributes used * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX nested attribute. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV4: * Nested attribute. The IPv4 source/destination address/port for offload * transmitting. See enum qca_wlan_vendor_attr_coap_offload_tx_ipv4 for the list * of supported attributes. * This attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV6: * Nested attribute. The IPv6 source/destination address/port for offload * transmitting. See enum qca_wlan_vendor_attr_coap_offload_tx_ipv6 for the list * of supported attributes. * This attribute is optional. * * At least one of %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV4 and * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV6 must be configured. * Firmware will transmit the packets on both IPv4 and IPv6 if both are * configured. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_PERIOD: * u32 attribute. Period in milliseconds for the periodic transmitting. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_MSG: * NLA_BINARY attribute, the maximum allowed size is 1152 bytes. * CoAP message (UDP payload) to be periodically transmitted. Firmware * is responsible for adding any necessary protocol headers. * This attribute is mandatory. */ enum qca_wlan_vendor_attr_coap_offload_periodic_tx { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV4 = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV6 = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_PERIOD = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_MSG = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_coap_offload_cache_info - Attributes used * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHES nested attribute. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_TS: * u64 attribute. Received time (since system booted in microseconds) of * the cached CoAP message. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV4: * u32 attribute. Source IPv4 address (in network byte order) of the cached * CoAP message. * This attribute is optional. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV6: * NLA_BINARY attribute, length is 16 bytes. * Source IPv6 address (in network byte order) of the cached CoAP message. * This attribute is optional. * * At most and at least one of * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV4 and * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV6 is given for * an entry. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_MSG: * NLA_BINARY attribute, the maximum allowed size is 1152 bytes. * The cached CoAP message (UDP payload). If the actual message size is * greater than the maximum size, it will be truncated and leaving only * the first 1152 bytes. * This attribute is mandatory. */ enum qca_wlan_vendor_attr_coap_offload_cache_info { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_TS = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV4 = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV6 = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_MSG = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_coap_offload_action - Actions for * vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD. * * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_ENABLE: * Enable CoAP offload reply. * If it's enabled, firmware will start offload processing on each suspend * and stop on each resume. * * Offload reply on match works as follows: * Reply the packets that match the filter with the given CoAP * message (with necessary protocol headers), increase the CoAP message * ID in the given CoAP message by one for the next use after each successful * transmission, and try to store the information of the received packet, * including the received time, source IP address, and CoAP message (UDP * payload). * * Firmware has a limit to the maximum stored entries, it takes the source IP * address as the key of an entry, and keeps at most one entry for each key. * A packet won't be stored if no entry for the same key is present and the * total number of the existing unexpired entries reaches the maximum value. * * If any configured item is changed, user space should disable offload reply * first and then issue a new enable request. * * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_DISABLE: * Disable CoAP offload reply and return information of any cached CoAP * messages. * * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_ENABLE: * Enable CoAP offload periodic transmitting. * If it's enabled, firmware will start offload periodic transmitting on * each suspend and stop on each resume. * * Offload periodic transmitting works as follows: * Send the given CoAP message (with necessary protocol headers) with the given * source/destination IP address/UDP port periodically based on the given * period and increase the CoAP message ID in the given CoAP message by one * for the next use after each successful transmission. * * If any configured item is changed, user space should disable offload * periodic transmitting first and then issue a new enable request. * * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_DISABLE: * Disable CoAP offload periodic transmitting. * * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_CACHE_GET: * Get information of the CoAP messages cached during offload reply * processing. The cache is cleared after retrieval. */ enum qca_wlan_vendor_coap_offload_action { QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_ENABLE = 0, QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_DISABLE = 1, QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_ENABLE = 2, QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_DISABLE = 3, QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_CACHE_GET = 4, }; /** * enum qca_wlan_vendor_attr_coap_offload - Used by the * vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD. * This is used to set parameters for CoAP offload processing, or get * cached CoAP messages from firmware. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION: * u32 attribute. Action to take in this vendor command. * See enum qca_wlan_vendor_coap_offload_action for supported actions. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REQ_ID: * u32 attribute. Represents the Request ID for the CoAP offload * configuration, which can help to identify the user entity starting * the CoAP offload processing and accordingly stop the respective * ones/get the cached CoAP messages with the matching ID. * This attribute is mandatory. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY: * Nested attribute. Parameters for offload reply. * See enum qca_wlan_vendor_attr_coap_offload_reply for the list of * supported attributes. * This attribute is mandatory if %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION * is QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_ENABLE, and is ignored * otherwise. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX: * Nested attribute. Parameters for offload periodic transmitting. * See enum qca_wlan_vendor_attr_coap_offload_periodic_tx for the list of * supported attributes. * This attribute is mandatory if %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION is * QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_ENABLE, and is ignored * otherwise. * * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHES: * Array of nested attributes. Information of the cached CoAP messages, * where each entry is taken from * enum qca_wlan_vendor_attr_coap_offload_cache_info. * This attribute is used for reporting the cached CoAP messages * in reply for command in which %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION * is QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_CACHE_GET or * QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_DISABLE. It means there is no * cached item if this attribute is not present. */ enum qca_wlan_vendor_attr_coap_offload { QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_INVALID = 0, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION = 1, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REQ_ID = 2, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY = 3, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX = 4, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHES = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_MAX = QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_scs_rule_config - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG to configure Stream Classification * Service (SCS) rule. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_RULE_ID: Mandatory u32 attribute. * Represents the unique id of SCS rule to be configured. * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_REQUEST_TYPE: Mandatory u8 attribute. * Represents the request type: add, remove, or change. * Values as defined in IEEE Std 802.11-2020, Table 9-246 (SCS Request * Type definitions). * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_OUTPUT_TID: Mandatory u8 attribute * in case of add/change request type. * Represents the output traffic identifier (TID) to be assigned to the flow * matching the rule. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_CLASSIFIER_TYPE: Mandatory u8 * attribute in case of add/change request type. * Represents type of classifier parameters present in SCS rule. * Refer IEEE Std 802.11-2020 Table 9-164 (Frame classifier type). * Only classifier types 4 and 10 are supported for SCS. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_VERSION: Mandatory u8 attribute * in case of add/change request type when classifier type is TCLAS4. * Represents the IP version (4: IPv4, 6: IPv6) of the rule. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV4_ADDR: Optional * attribute in case of add/change request type when classifier type is TCLAS4 * and version attribute is IPv4. * Represents the source IPv4 address in the rule which is to be compared * against the source IP address in the IPv4 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV4_ADDR: Optional * attribute in case of add/change request type when classifier type is TCLAS4 * and version attribute is IPv4. * Represents the destination IPv4 address in the rule which is to be compared * against the destination IP address in the IPv4 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV6_ADDR: Optional * attribute in case of add/change request type when classifier type is TCLAS4 * and version attribute is IPv6. * Represents the source IPv6 address in the rule which is to be compared * against the source IP address in the IPv6 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV6_ADDR: Optional * attribute in case of add/change request type when classifier type is TCLAS4 * and version attribute is IPv6. * Represents the destination IPv6 address in the rule which is to be compared * against the destination IP address in the IPv6 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_PORT: Optional u16 attribute * in case of add/change request type when classifier type is TCLAS4. * Represents the source port number in the rule which is to be compared against * the source port number in the protocol header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_PORT: Optional u16 attribute * in case of add/change request type when classifier type is TCLAS4. * Represents the destination port number in the rule which is to be compared * against the destination port number in the protocol header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DSCP: Optional u8 attribute * in case of add/change request type when classifier type is TCLAS4. * Represents the DSCP value in the rule which is to be compared against the * DSCP field present in the IP header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_NEXT_HEADER: Optional u8 * attribute in case of add/change request type when classifier type is TCLAS4. * Represents the protocol/next header in the rule which is to be compared * against the protocol/next header field present in the IPv4/IPv6 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_FLOW_LABEL: Optional * attribute of size 3 bytes present in case of add/change request type * when classifier type is TCLAS4 and version is IPv6. * Represents the flow label value in the rule which is to be compared against * the flow label field present in the IPv6 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_PROTOCOL_INSTANCE: Optional u8 * attribute in case of add/change request type when classifier type is TCLAS10. * Represents the protocol instance number in the rule. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER: Optional u8 * attribute in case of add/change request type when classifier type is TCLAS10. * Represents the protocol/next header in the rule which is to be compared * against the protocol/next header field present in the IPv4/IPv6 header. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_MASK: Optional * attribute of variable length present when request type is add/change and * classifier type is TCLAS10. * Represents the mask to be used for masking the header contents of the header * specified by QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER * attribute. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_VALUE: Optional * attribute of variable length present when request type is add/change and * classifier type is TCLAS10. * Represents the value to be compared against after masking the header contents * of the header specified by the * QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER attribute with the * filter mask specified by the * QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_MASK attribute. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_SERVICE_CLASS_ID: Optional u16 * attribute. * Represents the service class id of the configured SCS rule. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_DST_MAC_ADDR: Optional 6 bytes * MAC address. * Represents the destination MAC address in the rule. * * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_NETDEV_IF_INDEX: Optional u32 attribute * Represents the netdevice interface index in the rule. */ enum qca_wlan_vendor_attr_scs_rule_config { QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_RULE_ID = 1, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_REQUEST_TYPE = 2, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_OUTPUT_TID = 3, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_CLASSIFIER_TYPE = 4, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_VERSION = 5, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV4_ADDR = 6, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV4_ADDR = 7, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV6_ADDR = 8, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV6_ADDR = 9, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_PORT = 10, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_PORT = 11, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DSCP = 12, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_NEXT_HEADER = 13, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_FLOW_LABEL = 14, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_PROTOCOL_INSTANCE = 15, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER = 16, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_MASK = 17, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_VALUE = 18, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_SERVICE_CLASS_ID = 19, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_DST_MAC_ADDR = 20, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_NETDEV_IF_INDEX = 21, /* Keep last */ QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_sar_version - This describes the current SAR version * used in the firmware. * * @QCA_WLAN_VENDOR_SAR_VERSION_1: The firmware supports legacy SAR. * In legacy SAR, the firmware supports 5 static and 1 user defined SAR limits. * * @QCA_WLAN_VENDOR_SAR_VERSION_2: The firmware supports SAR version 2, * i.e., SAR Non DBS mode. In SAR version 2, the firmware has 6 SAR tables for * each CTL group. So user can select up to 6 SAR indexes from the current CTL * groups. * * @QCA_WLAN_VENDOR_SAR_VERSION_3: The firmware supports SAR version 3, * i.e., SAR DBS mode. In SAR version 3, the firmware has 6 SAR tables for each * CTL group but user can choose up to 3 SAR set index only, as the top half * of the SAR index (0 to 2) is used for non DBS purpose and the bottom half of * the SAR index (3 to 5) is used for DBS mode. * * @QCA_WLAN_VENDOR_SAR_VERSION_4: The firmware supports SAR version 4, * known as SAR Smart Transmit (STX) mode. STX is time averaging algorithmic * for power limit computation in collaboration with WWAN. * In STX mode, firmware has 41 indexes and there is no ctl grouping uses. * * @QCA_WLAN_VENDOR_SAR_VERSION_5: The firmware supports SAR version 5, * known as TAS (Time Averaging SAR) mode. In TAS mode, as name implies * instead of fixed static SAR power limit firmware uses time averaging * to adjust the SAR limit dynamically. It is wlan soc standalone mechanism. * In this mode firmware has up to 43 indexes. */ enum qca_wlan_vendor_sar_version { QCA_WLAN_VENDOR_SAR_VERSION_INVALID = 0, QCA_WLAN_VENDOR_SAR_VERSION_1 = 1, QCA_WLAN_VENDOR_SAR_VERSION_2 = 2, QCA_WLAN_VENDOR_SAR_VERSION_3 = 3, QCA_WLAN_VENDOR_SAR_VERSION_4 = 4, QCA_WLAN_VENDOR_SAR_VERSION_5 = 5, }; /** * enum qca_wlan_vendor_sar_ctl_group_state - This describes whether * CTL grouping is enabled or disabled in the firmware. * * @QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_ENABLED: CTL grouping * is enabled in firmware. * * @QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_DISABLED: CTL grouping * is disabled in firmware. * */ enum qca_wlan_vendor_sar_ctl_group_state { QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_INVALID = 0, QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_ENABLED = 1, QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_DISABLED = 2, }; /** * enum qca_wlan_vendor_attr_sar_capability - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY to get SAR capabilities * supported by the firmware. * @QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_VERSION: * u32 attribute. This field describes current SAR version supported by the * firmware. * See enum qca_wlan_vendor_sar_version for more information. * This attribute is mandatory. * @QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_CTL_GROUP_STATE: * u32 attribute. This field describes whether CTL groups are enabled * or disabled in the firmware. * See enum qca_wlan_vendor_sar_ctl_group_state for more information. * This attribute is optional. */ enum qca_wlan_vendor_attr_sar_capability { QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_VERSION = 1, QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_CTL_GROUP_STATE = 2, /* Keep last */ QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_MAX = QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_sr_stats - Attributes for Spatial Reuse statistics. * These statistics are sent from the driver in a response when userspace * queries to get the statistics using the operation * %QCA_WLAN_SR_OPERATION_GET_STATS. These statistics are reset * by the driver when the SR feature is enabled, when the driver receives * %QCA_WLAN_SR_OPERATION_CLEAR_STATS operation, or when disconnected. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_OPPORTUNITIES_COUNT: u32 attribute. * Mandatory only when non-SRG is supported by the AP and optional otherwise. * This represents the number of non-SRG TX opportunities. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_TRIED_COUNT: u32 attribute. * Mandatory only when non-SRG is supported by the AP and optional otherwise. * This represents the number of non-SRG PPDUs tried to transmit. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_SUCCESS_COUNT: u32 attribute. * Mandatory only when non-SRG is supported by the AP and optional otherwise. * This represents the number of non-SRG PPDUs successfully transmitted. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_OPPORTUNITIES_COUNT: u32 attribute. * Mandatory only when SRG is supported by the AP and optional otherwise. * This represents the number of SRG TX opportunities. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_TRIED_COUNT: u32 attribute. * Mandatory only when SRG is supported by the AP and optional otherwise. * This represents the number of SRG PPDUs tried to transmit. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_SUCCESS_COUNT: u32 attribute. * Mandatory only when SRG is supported by the AP and optional otherwise. * This represents the number of SRG PPDUs successfully transmitted. */ enum qca_wlan_vendor_attr_sr_stats { QCA_WLAN_VENDOR_ATTR_SR_STATS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_OPPORTUNITIES_COUNT = 1, QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_TRIED_COUNT = 2, QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_SUCCESS_COUNT = 3, QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_OPPORTUNITIES_COUNT = 4, QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_TRIED_COUNT = 5, QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_SUCCESS_COUNT = 6, /* Keep last */ QCA_WLAN_VENDOR_ATTR_SR_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SR_STATS_MAX = QCA_WLAN_VENDOR_ATTR_SR_STATS_AFTER_LAST - 1, }; /** * enum qca_wlan_sr_reason_code - Defines the different reason codes used in * Spatial Reuse feature. * * @QCA_WLAN_SR_REASON_CODE_ROAMING: The SR feature is disabled/enabled due to * roaming to an AP that doesn't support/supports SR feature, respectively. * * @QCA_WLAN_SR_REASON_CODE_CONCURRENCY: The SR feature is disabled/enabled due * to change in concurrent interfaces that are supported by the driver. */ enum qca_wlan_sr_reason_code { QCA_WLAN_SR_REASON_CODE_ROAMING = 0, QCA_WLAN_SR_REASON_CODE_CONCURRENCY = 1, }; /** * enum qca_wlan_sr_operation - Defines the different types of SR operations. * The values are used inside attribute %QCA_WLAN_VENDOR_ATTR_SR_OPERATION. * * @QCA_WLAN_SR_OPERATION_SR_ENABLE: Userspace sends this operation to the * driver to enable the Spatial Reuse feature. Attributes * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD and * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD are used with this * operation. * * @QCA_WLAN_SR_OPERATION_SR_DISABLE: Userspace sends this operation to the * driver to disable the Spatial Reuse feature. * * @QCA_WLAN_SR_OPERATION_SR_SUSPEND: The driver uses this operation in an * asynchronous event sent to userspace when the SR feature is disabled. * The disable reason is encoded in QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE * and sent along with the asynchronous event. * * @QCA_WLAN_SR_OPERATION_SR_RESUME: The driver uses this operation in an * asynchronous event when the SR feature is enabled again after the SR feature * was suspended by the driver earlier. The enable reason is * encoded in QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE. Attributes used are * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD and * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD. * * @QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_PROHIBIT: This operation is * used to prohibit PSR-based spatial reuse and non-SRG OBSS PD-based spatial * reuse transmissions. Userspace sends this operation to the driver. * The driver/firmware upon receiving this operation shall prohibit PSR-based * spatial reuse and non-SRG OBSS PD-based spatial reuse transmissions. * * @QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_ALLOW: This operation is * used to allow PSR-based spatial reuse and non-SRG OBSS PD-based spatial * reuse transmissions. Userspace sends this operation to the driver. * The driver/firmware upon receiving this operation shall allow PSR-based * spatial reuse and non-SRG OBSS PD-based spatial reuse transmissions. * * @QCA_WLAN_SR_OPERATION_GET_STATS: Userspace sends this operation to the * driver to get the SR statistics and the driver sends a synchronous response * with the attributes defined in enum qca_wlan_vendor_attr_sr_stats using the * nested attribute %QCA_WLAN_VENDOR_ATTR_SR_STATS. * * @QCA_WLAN_SR_OPERATION_CLEAR_STATS: Userspace sends this operation to the * driver to clear the SR statistics and upon receiving this operation * the driver/firmware shall clear the SR statistics. * * @QCA_WLAN_SR_OPERATION_GET_PARAMS: Userspace sends this operation to the * driver to get the SR parameters and the driver sends the synchronous response * with the following required attributes: * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW. * * @QCA_WLAN_SR_OPERATION_UPDATE_PARAMS: The driver uses this operation in an * asynchronous event to userspace to update any changes in SR parameters. * The following attributes are used with this operation: * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE, * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW. */ enum qca_wlan_sr_operation { QCA_WLAN_SR_OPERATION_SR_ENABLE = 0, QCA_WLAN_SR_OPERATION_SR_DISABLE = 1, QCA_WLAN_SR_OPERATION_SR_SUSPEND = 2, QCA_WLAN_SR_OPERATION_SR_RESUME = 3, QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_PROHIBIT = 4, QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_ALLOW = 5, QCA_WLAN_SR_OPERATION_GET_STATS = 6, QCA_WLAN_SR_OPERATION_CLEAR_STATS = 7, QCA_WLAN_SR_OPERATION_GET_PARAMS = 8, QCA_WLAN_SR_OPERATION_UPDATE_PARAMS = 9, }; /** * enum qca_wlan_vendor_attr_sr_params - Defines attributes for SR configuration * parameters used by attribute %QCA_WLAN_VENDOR_ATTR_SR_PARAMS. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE: Flag attribute. * This attribute is optionally set in response to * %QCA_WLAN_SR_OPERATION_GET_PARAMS and in request when operation is set to * %QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_PROHIBIT. Refer IEEE Std * 802.11ax-2021 Figure 9-788r-SR Control field format to understand more * about HESIGA_Spatial_reuse_value15_allowed. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW: Flag attribute. * This attribute is used in response to %QCA_WLAN_SR_OPERATION_GET_PARAMS * operation. This indicates whether non-SRG OBSS PD SR transmissions are * allowed or not at non-AP STAs that are associated with the AP. If present * non-SRG OBSS PD SR transmissions are not allowed else are allowed. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET: Optional u8 * attribute. This attribute is used in response to * %QCA_WLAN_SR_OPERATION_GET_PARAMS operation. This indicates the SRG OBSS PD * Min Offset field which contains an unsigned integer that is added to -82 dBm * to generate the value of the SRG OBSS PD Min parameter. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET: Optional u8 * attribute. This attribute is used in response to * %QCA_WLAN_SR_OPERATION_GET_PARAMS operation. This indicates the SRG OBSS PD * Max Offset field which contains an unsigned integer that is added to -82 dBm * to generate the value of the SRG OBSS PD Max parameter. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET: Optional u8 * attribute. This attribute is used in response to * %QCA_WLAN_SR_OPERATION_GET_PARAMS operation. This indicates the Non-SRG OBSS * PD Max Offset field which contains an unsigned integer that is added to -82 * dBm to generate the value of the Non-SRG OBSS PD Max parameter. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD: s32 attribute (in dBm). * Userspace optionally sends this attribute with * %QCA_WLAN_SR_OPERATION_SR_ENABLE operation to the driver to specify the * preferred SRG PD threshold. The driver shall send this attribute to * userspace in SR resume event to indicate the PD threshold being used for SR. * When there is change in SRG PD threshold (for example, due to roaming, etc.) * the driver shall indicate the userspace the newly configured SRG PD threshold * using an asynchronous event. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD: s32 attribute (in dBm). * Userspace optionally sends this attribute with * %QCA_WLAN_SR_OPERATION_SR_ENABLE operation to the driver to specify the * preferred non-SRG PD threshold. The driver shall send this attribute to * userspace in SR resume event to indicate the PD threshold being used for SR. * When there is change in non-SRG PD threshold (for example, due to roaming, * etc.) the driver shall indicate the userspace the newly configured non-SRG PD * threshold using an asynchronous event. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE: u32 attribute. The possible * values are defined in enum qca_wlan_sr_reason_code. This * attribute is used with %QCA_WLAN_SR_OPERATION_SR_RESUME and * %QCA_WLAN_SR_OPERATION_SR_SUSPEND operations. */ enum qca_wlan_vendor_attr_sr_params { QCA_WLAN_VENDOR_ATTR_SR_PARAMS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE = 1, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW = 2, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET = 3, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET = 4, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET = 5, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD = 6, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD = 7, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE = 8, /* keep last */ QCA_WLAN_VENDOR_ATTR_SR_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SR_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_SR_PARAMS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_sr - Defines the attributes used by the vendor * command QCA_NL80211_VENDOR_SUBCMD_SR. * * @QCA_WLAN_VENDOR_ATTR_SR_OPERATION: Mandatory u8 attribute for all requests * from userspace to the driver. Possible values are defined in enum * qca_wlan_sr_operation. * * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS: Nested attribute, contains the SR * configuration parameters. The possible attributes inside this attribute are * defined in enum qca_wlan_vendor_attr_sr_params. * This attribute is used when QCA_WLAN_VENDOR_ATTR_SR_OPERATION is set to * %QCA_WLAN_SR_OPERATION_SR_ENABLE in requests from userspace to the driver and * also in response from the driver to userspace when the response is sent for * %QCA_WLAN_SR_OPERATION_GET_PARAMS. * The driver uses this attribute in asynchronous events in which the operation * is set to %QCA_WLAN_SR_OPERATION_SR_RESUME, * %QCA_WLAN_SR_OPERATION_SR_SUSPEND or %QCA_WLAN_SR_OPERATION_UPDATE_PARAMS. * * @QCA_WLAN_VENDOR_ATTR_SR_STATS: Nested attribute, contains the SR * statistics. These attributes used inside this are defined in enum * qca_wlan_vendor_attr_sr_stats. * This attribute is used in response from the driver to a command in which * %QCA_WLAN_VENDOR_ATTR_SR_OPERATION is set to * %QCA_WLAN_SR_OPERATION_GET_STATS. */ enum qca_wlan_vendor_attr_sr { QCA_WLAN_VENDOR_ATTR_SR_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SR_OPERATION = 1, QCA_WLAN_VENDOR_ATTR_SR_PARAMS = 2, QCA_WLAN_VENDOR_ATTR_SR_STATS = 3, /* Keep last */ QCA_WLAN_VENDOR_ATTR_SR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SR_MAX = QCA_WLAN_VENDOR_ATTR_SR_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event - Defines the attributes * used in the QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT subcommand. * * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MACADDR: 6 byte MAC address * used by the peer on the link that corresponds to the link used for sending * the event notification. * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MLD_MAC_ADDR: 6 byte * MLD MAC address of the peer. * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_PRIM_IFINDEX: u32 attribute, * used to pass ifindex of the primary netdev. * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MLD_IFINDEX: u32 attribute, * used to pass ifindex of the MLD netdev. * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_NUM_LINKS: u8 attribute, * used to indicate the number of links that the non-AP MLD negotiated to be * used in the ML connection. * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_LINK_INFO: Nested * attribute, contains information regarding links of the non-AP MLD. * User applications need to know all the links of a non-AP MLD that are * participating in the ML association. The possible attributes inside this * attribute are defined in enum qca_wlan_vendor_attr_mlo_link_info. */ enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event { QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MACADDR = 1, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MLD_MAC_ADDR = 2, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_PRIM_IFINDEX = 3, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MLD_IFINDEX = 4, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_NUM_LINKS = 5, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_LINK_INFO = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mlo_link_info - Defines attributes for * non-AP MLD link parameters used by the attribute * %QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_LINK_INFO. * * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_IFINDEX: u32 attribute, used * to pass the netdev ifindex of the non-AP MLD link. * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_MACADDR: 6 byte MAC address of * the non-AP MLD link. */ enum qca_wlan_vendor_attr_mlo_link_info { QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_IFINDEX = 1, QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_MACADDR = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_MAX = QCA_WLAN_VENDOR_ATTR_MLO_LINK_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_afc_freq_psd_info: This enum is used with * nested attributes QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO and * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST to update the frequency range * and PSD information. * * @QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_START: Required and type is * u32. This attribute is used to indicate the start of the queried frequency * range in MHz. * * @QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_END: Required and type is u32. * This attribute is used to indicate the end of the queried frequency range * in MHz. * * @QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_PSD: Required and type is u32. * This attribute will contain the PSD information for a single range as * specified by the QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_START and * QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_END attributes. * * The PSD power info (dBm/MHz) from user space should be multiplied * by a factor of 100 when sending to the driver to preserve granularity * up to 2 decimal places. * Example: * PSD power value: 10.21 dBm/MHz * Value to be updated in QCA_WLAN_VENDOR_ATTR_AFC_PSD_INFO: 1021. * * Note: QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_PSD attribute will be used only * with nested attribute QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO and with * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE. * * The following set of attributes will be used to exchange frequency and * corresponding PSD information for AFC between the user space and the driver. */ enum qca_wlan_vendor_attr_afc_freq_psd_info { QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_START = 1, QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_END = 2, QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_PSD = 3, QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_MAX = QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_afc_chan_eirp_info: This enum is used with * nested attribute QCA_WLAN_VENDOR_ATTR_AFC_CHAN_LIST_INFO to update the * channel list and corresponding EIRP information. * * @QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM: Required and type is u8. * This attribute is used to indicate queried channel from * the operating class indicated in QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO. * * @QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP: Optional and type is u32. * This attribute is used to configure the EIRP power info corresponding * to the channel number indicated in QCA_WLAN_VENDOR_ATTR_AFC_CHAN_NUM. * The EIRP power info(dBm) from user space should be multiplied * by a factor of 100 when sending to Driver to preserve granularity up to * 2 decimal places. * Example: * EIRP power value: 34.23 dBm * Value to be updated in QCA_WLAN_VENDOR_ATTR_AFC_EIRP_INFO: 3423. * * Note: QCA_WLAN_VENDOR_ATTR_AFC_EIRP_INFO attribute will only be used with * nested attribute QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO and * with QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_LIST when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE: * * The following set of attributes will be used to exchange Channel and * corresponding EIRP information for AFC between the user space and Driver. */ enum qca_wlan_vendor_attr_afc_chan_eirp_info { QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM = 1, QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP = 2, QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_MAX = QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_afc_opclass_info: This enum is used with nested * attributes QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO and * QCA_WLAN_VENDOR_ATTR_AFC_REQ_OPCLASS_CHAN_INFO to update the operating class, * channel, and EIRP related information. * * @QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS: Required and type is u8. * This attribute is used to indicate the operating class, as listed under * IEEE Std 802.11-2020 Annex E Table E-4, for the queried channel list. * * @QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST: Array of nested attributes * for updating the channel number and EIRP power information. * It uses the attributes defined in * enum qca_wlan_vendor_attr_afc_chan_eirp_info. * * Operating class information packing format for * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_INFO when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE_EXPIRY. * * m - Total number of operating classes. * n, j - Number of queried channels for the corresponding operating class. * * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[0] * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[0] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] * ..... * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[n - 1] * .... * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[m] * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[m] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] * .... * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[j - 1] * * Operating class information packing format for * QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO and * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_INFO when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE. * * m - Total number of operating classes. * n, j - Number of channels for the corresponding operating class. * * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[0] * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[0] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[0] * ..... * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[n - 1] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[n - 1] * .... * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[m] * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[m] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[0] * .... * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[j - 1] * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[j - 1] * * The following set of attributes will be used to exchange operating class * information for AFC between the user space and the driver. */ enum qca_wlan_vendor_attr_afc_opclass_info { QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS = 1, QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST = 2, QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_MAX = QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_afc_event_type: Defines values for AFC event type. * Attribute used by QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE attribute. * * @QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY: AFC expiry event sent from the * driver to userspace in order to query the new AFC power values. * * @QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE: Power update * complete event will be sent from the driver to userspace to indicate * processing of the AFC response. * * @QCA_WLAN_VENDOR_AFC_EVENT_TYPE_PAYLOAD_RESET: AFC payload reset event * will be sent from the driver to userspace to indicate last received * AFC response data has been cleared on the AP due to invalid data * in the QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE. * * The following enum defines the different event types that will be * used by the driver to help trigger corresponding AFC functionality in user * space. */ enum qca_wlan_vendor_afc_event_type { QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY = 0, QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE = 1, QCA_WLAN_VENDOR_AFC_EVENT_TYPE_PAYLOAD_RESET = 2, }; /** * enum qca_wlan_vendor_afc_ap_deployment_type: Defines values for AP * deployment type. * Attribute used by QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AP_DEPLOYMENT attribute. * * @QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_UNKNOWN: Unknown AP deployment. * * @QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_INDOOR: Indoor AP deployment. * * @QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_OUTDOOR: Outdoor AP deployment. * * The following enum defines different deployment modes that the AP might * come up in. This information will be essential to retrieve deployment-type * specific SP power values for AFC operation. */ enum qca_wlan_vendor_afc_ap_deployment_type { QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_UNKNOWN = 0, QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_INDOOR = 1, QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_OUTDOOR = 2, }; /** * enum qca_wlan_vendor_afc_evt_status_code: Defines values AP will use to * indicate AFC response status. * Enum used by QCA_WLAN_VENDOR_ATTR_AFC_EVENT_STATUS_CODE attribute. * * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_SUCCESS: Success * * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_TIMEOUT: Indicates AFC indication * command was not received within the expected time of the AFC expiry event * being triggered. * * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_PARSING_ERROR: Indicates AFC data * parsing error by the driver. * * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_LOCAL_ERROR: Indicates any other local * error. * * The following enum defines the status codes that the driver will use to * indicate whether the AFC data is valid or not. */ enum qca_wlan_vendor_afc_evt_status_code { QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_SUCCESS = 0, QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_TIMEOUT = 1, QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_PARSING_ERROR = 2, QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_LOCAL_ERROR = 3, }; /** * enum qca_wlan_vendor_attr_afc_event: Defines attributes to be used with * vendor event QCA_NL80211_VENDOR_SUBCMD_AFC_EVENT. These attributes will * support sending only a single request to the user space at a time. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE: Required u8 attribute. * Used with event to notify the type of AFC event received. * Valid values are defined in enum qca_wlan_vendor_afc_event_type. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AP_DEPLOYMENT: u8 attribute. Required when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY, * otherwise unused. * * This attribute is used to indicate the AP deployment type in the AFC request. * Valid values are defined in enum qca_wlan_vendor_afc_ap_deployment_type. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_REQ_ID: Required u32 attribute. * Unique request identifier generated by the AFC client for every * AFC expiry event trigger. See also QCA_WLAN_VENDOR_ATTR_AFC_RESP_REQ_ID. * The user space application is responsible for ensuring no duplicate values * are in-flight with the server, e.g., by delaying a request, should the same * value be received from different radios in parallel. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFC_WFA_VERSION: u32 attribute. Optional. * It is used when the QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY, otherwise unused. * * This attribute indicates the AFC spec version information. This will * indicate the AFC version AFC client must use to query the AFC data. * Bits 15:0 - Minor version * Bits 31:16 - Major version * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_MIN_DES_POWER: u16 attribute. Required when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY, * otherwise unused. * This attribute indicates the minimum desired power (in dBm) for * the queried spectrum. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_STATUS_CODE: u8 attribute. Required when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. * * Valid values are defined in enum qca_wlan_vendor_afc_evt_status_code. * This attribute is used to indicate if there were any errors parsing the * AFC response. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_SERVER_RESP_CODE: s32 attribute. Required * when QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. * * This attribute indicates the AFC response code. The AFC response codes are * in the following categories: * -1: General Failure. * 0: Success. * 100 - 199: General errors related to protocol. * 300 - 399: Error events specific to message exchange * for the Available Spectrum Inquiry. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_DATE: u32 attribute. Required when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. * * This attribute indicates the date until which the current response is * valid for in UTC format. * Date format: bits 7:0 - DD (Day 1-31) * bits 15:8 - MM (Month 1-12) * bits 31:16 - YYYY (Year) * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_TIME: u32 attribute. Required when * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. * * This attribute indicates the time until which the current response is * valid for in UTC format. * Time format: bits 7:0 - SS (Seconds 0-59) * bits 15:8 - MM (Minutes 0-59) * bits 23:16 - HH (Hours 0-23) * bits 31:24 - Reserved * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST: Array of nested attributes * for updating the list of frequency ranges to be queried. * Required when QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY or * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. * It uses the attributes defined in * enum qca_wlan_vendor_attr_afc_freq_psd_info. * * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_LIST: Array of nested attributes * for updating the list of operating classes and corresponding channels to be * queried. * Required when QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY or * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. * It uses the attributes defined in enum qca_wlan_vendor_attr_afc_opclass_info. */ enum qca_wlan_vendor_attr_afc_event { QCA_WLAN_VENDOR_ATTR_AFC_EVENT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE = 1, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AP_DEPLOYMENT = 2, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_REQ_ID = 3, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFC_WFA_VERSION = 4, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_MIN_DES_POWER = 5, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_STATUS_CODE = 6, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_SERVER_RESP_CODE = 7, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_DATE = 8, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_TIME = 9, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST = 10, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_LIST = 11, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AFC_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_afc_response: Defines attributes to be used * with vendor command QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE. These attributes * will support sending only a single AFC response to the driver at a time. * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_DATA: Type is NLA_STRING. Required attribute. * This attribute will be used to send a single Spectrum Inquiry response object * from the 'availableSpectrumInquiryResponses' array object from the response * JSON. * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_TIME_TO_LIVE: Required u32 attribute. * * This attribute indicates the period (in seconds) for which the response * data received is valid for. * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_REQ_ID: Required u32 attribute. * * This attribute indicates the request ID for which the corresponding * response is being sent for. See also QCA_WLAN_VENDOR_ATTR_AFC_EVENT_REQ_ID. * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_DATE: Required u32 attribute. * * This attribute indicates the date until which the current response is * valid for in UTC format. * Date format: bits 7:0 - DD (Day 1-31) * bits 15:8 - MM (Month 1-12) * bits 31:16 - YYYY (Year) * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_TIME: Required u32 attribute. * * This attribute indicates the time until which the current response is * valid for in UTC format. * Time format: bits 7:0 - SS (Seconds 0-59) * bits 15:8 - MM (Minutes 0-59) * bits 23:16 - HH (Hours 0-23) * bits 31:24 - Reserved * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFC_SERVER_RESP_CODE: Required s32 attribute. * * This attribute indicates the AFC response code. The AFC response codes are * in the following categories: * -1: General Failure. * 0: Success. * 100 - 199: General errors related to protocol. * 300 - 399: Error events specific to message exchange * for the Available Spectrum Inquiry. * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO: Array of nested attributes * for PSD info of all the queried frequency ranges. It uses the attributes * defined in enum qca_wlan_vendor_attr_afc_freq_psd_info. Required attribute. * * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO: Array of nested * attributes for EIRP info of all queried operating class/channels. It uses * the attributes defined in enum qca_wlan_vendor_attr_afc_opclass_info and * enum qca_wlan_vendor_attr_afc_chan_eirp_info. Required attribute. * */ enum qca_wlan_vendor_attr_afc_response { QCA_WLAN_VENDOR_ATTR_AFC_RESP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AFC_RESP_DATA = 1, QCA_WLAN_VENDOR_ATTR_AFC_RESP_TIME_TO_LIVE = 2, QCA_WLAN_VENDOR_ATTR_AFC_RESP_REQ_ID = 3, QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_DATE = 4, QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_TIME = 5, QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFC_SERVER_RESP_CODE = 6, QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO = 7, QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO = 8, QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AFC_RESP_MAX = QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFTER_LAST - 1, }; /** * enum qca_wlan_dozed_ap_state - Doze states for AP interface * * @QCA_WLAN_DOZED_AP_DISABLE: Disable doze state on the AP interface. * * @QCA_WLAN_DOZED_AP_ENABLE: Enable doze state on the AP interface. AP starts * beaconing at higher beacon interval with Rx disabled. */ enum qca_wlan_dozed_ap_state { QCA_WLAN_DOZED_AP_DISABLE = 0, QCA_WLAN_DOZED_AP_ENABLE = 1, }; /** * enum qca_wlan_vendor_attr_dozed_ap - Used by the vendor command * @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP to configure or receive dozed AP mode * configuration. * * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_STATE: u8 attribute. * Configures the doze state for an AP interface. Possible values are defined * in enum qca_wlan_dozed_ap_state. @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP event * gets triggered asynchronously to provide updated AP interface configuration. * * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_COOKIE: Unsigned 64-bit cookie provided by * the driver in the response to specific @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP * command, which is used later to maintain synchronization between commands * and asynchronous events. * * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_NEXT_TSF: u64 attribute. * Used in event to indicate the next TBTT TSF timer value after applying the * doze mode configuration. Next TBTT TSF is the time at which the AP sends * the first beacon after entering or exiting dozed mode. * * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_BI_MULTIPLIER: u16 attribute. * Used with event to inform the periodicity of beacon transmission that would * be skipped at all TBTTs in between. */ enum qca_wlan_vendor_attr_dozed_ap { QCA_WLAN_VENDOR_ATTR_DOZED_AP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DOZED_AP_STATE = 1, QCA_WLAN_VENDOR_ATTR_DOZED_AP_COOKIE = 2, QCA_WLAN_VENDOR_ATTR_DOZED_AP_NEXT_TSF = 3, QCA_WLAN_VENDOR_ATTR_DOZED_AP_BI_MULTIPLIER = 4, /* Keep last */ QCA_WLAN_VENDOR_ATTR_DOZED_AP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DOZED_AP_MAX = QCA_WLAN_VENDOR_ATTR_DOZED_AP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_monitor_mode_status - Represents the status codes * used with QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE. * @QCA_WLAN_VENDOR_MONITOR_MODE_NO_CAPTURE_RUNNING: Used to indicate no * capture running status. * @QCA_WLAN_VENDOR_MONITOR_MODE_CAPTURE_RUNNING: Used to indicate * capture running status. **/ enum qca_wlan_vendor_monitor_mode_status { QCA_WLAN_VENDOR_MONITOR_MODE_NO_CAPTURE_RUNNING = 0, QCA_WLAN_VENDOR_MONITOR_MODE_CAPTURE_RUNNING = 1, }; /** * enum qca_wlan_vendor_attr_get_monitor_mode - Used by the * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE to report * information regarding the local packet capture over the monitor mode. * * @QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_STATUS: u32 attribute. This attribute * represents the status of the start capture commands. The values used with * this attribute are defined in enum qca_wlan_vendor_monitor_mode_status. This * is returned by the driver in the response to the command. */ enum qca_wlan_vendor_attr_get_monitor_mode { QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_STATUS = 1, /* Keep last */ QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_MAX = QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_link_state_op_types - Defines different types of * operations for which %QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE can be used. * Will be used with %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE attribute. * * @QCA_WLAN_VENDOR_LINK_STATE_OP_GET - Get the MLO links state information. * @QCA_WLAN_VENDOR_LINK_STATE_OP_SET - Set the MLO links state information. */ enum qca_wlan_vendor_link_state_op_types { QCA_WLAN_VENDOR_LINK_STATE_OP_GET = 0, QCA_WLAN_VENDOR_LINK_STATE_OP_SET = 1, }; /** * enum qca_wlan_vendor_link_state_control_modes - Represents the types of MLO * links state control modes. This enum is used by * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE attribute. * * @QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_DEFAULT: MLO links state controlled * by the driver. * @QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_USER: MLO links state controlled by * user space. * @QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_MIXED: User space provides the * desired number of MLO links to operate in active state at any given time. * The driver will choose which MLO links should operate in the active state. * See enum qca_wlan_vendor_link_state for active state definition. */ enum qca_wlan_vendor_link_state_control_modes { QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_DEFAULT = 0, QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_USER = 1, QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_MIXED = 2, }; /** * enum qca_wlan_vendor_link_state_operation_modes - Represents the types of MLO * links state operation modes. This enum is used by * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OPERATION_MODE attribute. * * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_DEFAULT: In the default operation * mode, the driver selects the operating mode of the links, without any * guidance from the user space. * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_LATENCY: In the low latency * operation mode the driver should select MLO links that will achieve low * latency. * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_HIGH_THROUGHPUT: In the high * throughput operation mode the driver should select MLO links that will * achieve higher throughput. * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_POWER: In the low power * operation mode the driver should select MLO links that will achieve low * power. */ enum qca_wlan_vendor_link_state_operation_modes { QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_DEFAULT = 0, QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_LATENCY = 1, QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_HIGH_THROUGHPUT = 2, QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_POWER = 3, }; /** * enum qca_wlan_vendor_link_state - Represents the possible link states of an * MLO link. * * @QCA_WLAN_VENDOR_LINK_STATE_INACTIVE: In this state, the link will not * be used for data transmission but it can have TIDs mapped to it. It will be * in doze state always and does not monitor the beacons. * @QCA_WLAN_VENDOR_LINK_STATE_ACTIVE: In this state, the link will be * used for data TX/RX and monitors the beacons to check TIM bit indication. * It may enter doze state and comes out based on the transmit data traffic and * TIM bit indication in the beacon. */ enum qca_wlan_vendor_link_state { QCA_WLAN_VENDOR_LINK_STATE_INACTIVE = 0, QCA_WLAN_VENDOR_LINK_STATE_ACTIVE = 1, }; /** * enum qca_wlan_vendor_attr_link_state_config - Definition of attributes used * inside nested attribute %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG. * * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_LINK_ID: u8 attribute, link ID of the * MLO link. * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_STATE: u32 attribute. See * enum qca_wlan_vendor_link_state for possible MLO link states. */ enum qca_wlan_vendor_attr_link_state_config { QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_LINK_ID = 1, QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_STATE = 2, /* Keep last */ QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mlo_link_state - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE vendor command. * * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE: u32 attribute. Indicates the type * of the operation %QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE intended for. * Required only in a command. Possible values for this attribute are defined in * enum qca_wlan_vendor_link_state_op_types. * * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE: u32 attribute. Indicates MLO * links control mode type. Optional attribute in a command when * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to * %QCA_WLAN_VENDOR_LINK_STATE_OP_SET. Required attribute in a response when * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to * %QCA_WLAN_VENDOR_LINK_STATE_OP_GET. * See enum qca_wlan_vendor_link_state_control_modes for possible control modes. * * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG: Array of nested attributes. * Indicates the state of the each MLO link affiliated with the interface. * Required attribute in a command when %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE * is set to %QCA_WLAN_VENDOR_LINK_STATE_OP_SET and * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE is set to * %QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_USER. Required attribute in a * response when %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to * %QCA_WLAN_VENDOR_LINK_STATE_OP_GET. * See enum qca_wlan_vendor_attr_link_state_config for the nested attributes. * * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_MIXED_MODE_ACTIVE_NUM_LINKS: u8 attribute. * Represents the number of active state links. See enum * qca_wlan_vendor_link_state for active state definition. * Required attribute in a command when %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE * is set to %QCA_WLAN_VENDOR_LINK_STATE_OP_SET and * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE is set to * %QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_MIXED. * * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_OPERATION_MODE: u32 attribute. Indicates MLO * links operation mode type. Optional attribute in a command when * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to * %QCA_WLAN_VENDOR_LINK_STATE_OP_SET. Required attribute in a response when * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to * %QCA_WLAN_VENDOR_LINK_STATE_OP_GET. * See enum qca_wlan_vendor_link_state_operation_modes for possible operation * modes. */ enum qca_wlan_vendor_attr_mlo_link_state { QCA_WLAN_VENDOR_ATTR_LINK_STATE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE = 1, QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE = 2, QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG = 3, QCA_WLAN_VENDOR_ATTR_LINK_STATE_MIXED_MODE_ACTIVE_NUM_LINKS = 4, QCA_WLAN_VENDOR_ATTR_LINK_STATE_OPERATION_MODE = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_LINK_STATE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LINK_STATE_MAX = QCA_WLAN_VENDOR_ATTR_LINK_STATE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tid_link_map_status - Definition of attributes used * inside nested attribute %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS. * * @QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_UPLINK: Required u16 attribute * within nested attribute %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS. * Indicates the link mapping bitmap of a TID for uplink traffic. It is a * bitmask of the link IDs in which a bit set means that the TID is mapped with * that link ID in uplink traffic. Otherwise, the TID is not mapped to uplink * traffic for that link. * * @QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_DOWNLINK: Required u16 attribute * within nested attribute %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS. * Indicates the link mapping bitmap of a TID for downlink traffic. It is a * bitmask of the link IDs in which a bit set means that the TID is mapped with * that link ID in downlink traffic. Otherwise, the TID is not mapped to * downlink traffic for that link. */ enum qca_wlan_vendor_attr_tid_link_map_status { QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_UPLINK = 1, QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_DOWNLINK = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_MAX = QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_AFTER_LAST - 1, }; /* * enum qca_wlan_vendor_attr_tid_to_link_map: Definition of attributes used with * %QCA_NL80211_VENDOR_SUBCMD_TID_TO_LINK_MAP event. * * @QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AP_MLD_ADDR: Required attribute. 6-byte * AP MLD address with which this TID-to-link negotiation mapping is * established/updated. * * @QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS: Optional attribute. Array of * nested attributes containing TID-to-links mapping information. This will have * TID-to-link mapping for TID0 to TID7, each containing the uplink and downlink * map information. If this attribute is not present the default TID-to-link * mapping is in use, i.e., all TIDs are mapped to all links for both uplink and * downlink traffic. * See enum qca_wlan_vendor_attr_tid_link_map_status for the nested attributes. */ enum qca_wlan_vendor_attr_tid_to_link_map { QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AP_MLD_ADDR = 1, QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_MAX = QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_link_reconfig: Definition of attributes used * with %QCA_NL80211_VENDOR_SUBCMD_LINK_RECONFIG event. * * @QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AP_MLD_ADDR: Required attribute. * 6-byte AP MLD address of the AP which indicated the link reconfiguration. * * @QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_REMOVED_LINKS: Required u16 attribute. * A bitmap of the removed setup links link IDs. */ enum qca_wlan_vendor_attr_link_reconfig { QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AP_MLD_ADDR = 1, QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_REMOVED_LINKS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_MAX = QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tdls_disc_rsp_ext - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_TDLS_DISC_RSP_EXT vendor command. * * @QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_TX_LINK: u8 attribute. * Indicates the MLO link id on which the TDLS discovery response * frame is to be transmitted. */ enum qca_wlan_vendor_attr_tdls_disc_rsp_ext { QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_TX_LINK = 1, /* Keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_tdls_state - Represents the possible TDLS states. * * @QCA_WLAN_VENDOR_TDLS_STATE_DISABLED: TDLS is not enabled, default status * for all stations. * * @QCA_WLAN_VENDOR_TDLS_STATE_ENABLED: TDLS is enabled, but not yet tried to * establish the session. * * @QCA_WLAN_VENDOR_TDLS_STATE_ESTABLISHED: Direct link TDLS session is * established. * * @QCA_WLAN_VENDOR_TDLS_STATE_ESTABLISHED_OFF_CHANNEL: Direct link TDLS * session is established using MCC. * * @QCA_WLAN_VENDOR_TDLS_STATE_DROPPED: Direct link TDLS session was * established, but is temporarily dropped currently. * * @QCA_WLAN_VENDOR_TDLS_STATE_FAILED: TDLS session is failed to establish. */ enum qca_wlan_vendor_tdls_state { QCA_WLAN_VENDOR_TDLS_STATE_DISABLED = 1, QCA_WLAN_VENDOR_TDLS_STATE_ENABLED = 2, QCA_WLAN_VENDOR_TDLS_STATE_ESTABLISHED = 3, QCA_WLAN_VENDOR_TDLS_STATE_ESTABLISHED_OFF_CHANNEL = 4, QCA_WLAN_VENDOR_TDLS_STATE_DROPPED = 5, QCA_WLAN_VENDOR_TDLS_STATE_FAILED = 6, }; /** * enum qca_wlan_vendor_tdls_reason - Represents the possible TDLS reasons. * * @QCA_WLAN_TDLS_REASON_SUCCESS: TDLS session is successfully established. * * @QCA_WLAN_TDLS_REASON_UNSPECIFIED: Unspecified reason. * * @QCA_WLAN_TDLS_REASON_NOT_SUPPORTED: TDLS is not supported. * * @QCA_WLAN_TDLS_REASON_UNSUPPORTED_BAND: The specified band is not supported. * * @QCA_WLAN_TDLS_REASON_NOT_BENEFICIAL: Packets going through AP is better * than through direct link. * * @QCA_WLAN_TDLS_REASON_DROPPED_BY_REMOTE: Peer station doesn't want the TDLS * session anymore. */ enum qca_wlan_vendor_tdls_reason { QCA_WLAN_TDLS_REASON_SUCCESS = 0, QCA_WLAN_TDLS_REASON_UNSPECIFIED = -1, QCA_WLAN_TDLS_REASON_NOT_SUPPORTED = -2, QCA_WLAN_TDLS_REASON_UNSUPPORTED_BAND = -3, QCA_WLAN_TDLS_REASON_NOT_BENEFICIAL = -4, QCA_WLAN_TDLS_REASON_DROPPED_BY_REMOTE = -5, }; /** * enum qca_wlan_vendor_attr_tdls_enable - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE vendor command. * * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR: 6-byte MAC address of the peer * station to enable the TDLS session. Optional attribute. The driver sends the * TDLS session result as an asynchronous response using the command * %QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE when this peer MAC is provided in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE command. * * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_CHANNEL: u32 attribute. Indicates the * channel on which the TDLS session to be established. Required only when * %QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR is present. * * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_GLOBAL_OPERATING_CLASS: u32 attribute. * Indicates the global operating class of the TDLS session to be established. * Required only when %QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR is present. * * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX_LATENCY_MS: u32 attribute. Indicates * the maximum latency of the WLAN packets to be transmitted/received in * milliseconds on TDLS session. Required only when * %QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR is present. * * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MIN_BANDWIDTH_KBPS: u32 attribute. * Indicates the minimum bandwidth to be used to establish the TDLS session * in kbps. Required only when %QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR is * present. */ enum qca_wlan_vendor_attr_tdls_enable { QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_CHANNEL = 2, QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_GLOBAL_OPERATING_CLASS = 3, QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX_LATENCY_MS = 4, QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MIN_BANDWIDTH_KBPS = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tdls_disable - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE vendor command. * * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR: 6-byte MAC address of the peer * station to disable the TDLS session. Optional attribute. */ enum qca_wlan_vendor_attr_tdls_disable { QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tdls_get_status - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS vendor command. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR: 6-byte MAC address of the * peer station. Optional attribute. Used in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS request and response. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE: u32 attribute. Indicates the * TDLS session state with the peer specified in * %QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR. Uses the values from * enum qca_wlan_vendor_tdls_state. Used in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS response. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_REASON: s32 attribute. Indicates the * reason for the TDLS session state indicated in * %QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE. Uses the values from enum * qca_wlan_vendor_tdls_reason. Used in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS response. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_CHANNEL: u32 attribute. Indicates the * channel of the TDLS session established with * %QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR. Used in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS response. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_GLOBAL_OPERATING_CLASS: u32 attribute. * Indicates the global operating class of the TDLS session established with * %QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR. Used in * %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS response. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_NUM_SESSIONS: u32 attribute. Indicates * the current number of active TDLS sessions. This is indicated in the response * when %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS is requested with * %NL80211_ATTR_VENDOR_DATA as an empty nested attribute. * * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AVAILABLE: Flag attribute. Indicates * whether the driver can initiate new TDLS session. This is indicated in the * response when %QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS is requested with * %NL80211_ATTR_VENDOR_DATA as an empty nested attribute. */ enum qca_wlan_vendor_attr_tdls_get_status { QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE = 2, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_REASON = 3, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_CHANNEL = 4, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_GLOBAL_OPERATING_CLASS = 5, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_NUM_SESSIONS = 6, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AVAILABLE = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tdls_state - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE vendor command. * * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAC_ADDR: 6-byte MAC address of the * peer station. Required attribute. * * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CURRENT_STATE: u32 attribute. Indicates * the current TDLS state. Required attribute. Uses the values from * enum qca_wlan_vendor_tdls_state. * * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_REASON: s32 attribute. Indicates the * reason of the current TDLS session state. Required attribute. Uses the values * from enum qca_wlan_vendor_tdls_reason. * * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CHANNEL: u32 attribute. Indicates the * TDLS session channel. Required attribute. * * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_GLOBAL_OPERATING_CLASS: u32 attribute. * Indicates the TDLS session global operating class. Required attribute. */ enum qca_wlan_vendor_attr_tdls_state { QCA_WLAN_VENDOR_ATTR_TDLS_STATE_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAC_ADDR = 1, QCA_WLAN_VENDOR_ATTR_TDLS_STATE_NEW_STATE = 2, QCA_WLAN_VENDOR_ATTR_TDLS_STATE_REASON = 3, QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CHANNEL = 4, QCA_WLAN_VENDOR_ATTR_TDLS_STATE_GLOBAL_OPERATING_CLASS = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST - 1, }; /* * enum qca_wlan_vendor_opm_mode - Modes supported by * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT vendor attribute. * * @QCA_WLAN_VENDOR_OPM_MODE_DISABLE: OPM Disabled * @QCA_WLAN_VENDOR_OPM_MODE_ENABLE: OPM Enabled * @QCA_WLAN_VENDOR_OPM_MODE_USER_DEFINED: User defined mode which allows user * to configure power save inactivity timeout and speculative wake up * interval through %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO and * %QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE_INTERVAL attributes. */ enum qca_wlan_vendor_opm_mode { QCA_WLAN_VENDOR_OPM_MODE_DISABLE = 0, QCA_WLAN_VENDOR_OPM_MODE_ENABLE = 1, QCA_WLAN_VENDOR_OPM_MODE_USER_DEFINED = 2, }; /* enum qca_wlan_audio_transport_switch_type - Represents the possible transport * switch types. * * @QCA_WLAN_AUDIO_TRANSPORT_SWITCH_TYPE_NON_WLAN: Request to route audio data * via non-WLAN transport (ex: bluetooth). * * @QCA_WLAN_AUDIO_TRANSPORT_SWITCH_TYPE_WLAN: Request to route audio data via * WLAN transport. */ enum qca_wlan_audio_transport_switch_type { QCA_WLAN_AUDIO_TRANSPORT_SWITCH_TYPE_NON_WLAN = 0, QCA_WLAN_AUDIO_TRANSPORT_SWITCH_TYPE_WLAN = 1, }; /** * enum qca_wlan_audio_transport_switch_status - Represents the status of audio * transport switch request. * * @QCA_WLAN_AUDIO_TRANSPORT_SWITCH_STATUS_REJECTED: Request to switch transport * has been rejected. For ex: when transport switch is requested from WLAN * to non-WLAN transport, user space modules and peers would evaluate the switch * request and may not be ready for switch and hence switch to non-WLAN transport * gets rejected. * * @QCA_WLAN_AUDIO_TRANSPORT_SWITCH_STATUS_COMPLETED: Request to switch transport * has been completed. This is sent only in command path. Ex: when host driver * had requested for audio transport switch and userspace modules as well as * peers are ready for the switch, userspace module switches the transport and * sends subcommand with status completed to host driver. */ enum qca_wlan_audio_transport_switch_status { QCA_WLAN_AUDIO_TRANSPORT_SWITCH_STATUS_REJECTED = 0, QCA_WLAN_AUDIO_TRANSPORT_SWITCH_STATUS_COMPLETED = 1, }; /** * enum qca_wlan_vendor_attr_audio_transport_switch - Attributes used by * %QCA_NL80211_VENDOR_SUBCMD_AUDIO_TRANSPORT_SWITCH vendor command. * * @QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_TYPE: u8 attribute. Indicates * the transport switch type from one of the values in enum * qca_wlan_audio_transport_switch_type. This is mandatory param in both * command and event path. This attribute is included in both requests and * responses. * * @QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_STATUS: u8 attribute. Indicates * the transport switch status from one of the values in enum * qca_wlan_audio_transport_switch_status. This is optional param and used in * both command and event path. This attribute must not be included in requests. */ enum qca_wlan_vendor_attr_audio_transport_switch { QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_INVALID = 0, QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_TYPE = 1, QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_STATUS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_MAX = QCA_WLAN_VENDOR_ATTR_AUDIO_TRANSPORT_SWITCH_AFTER_LAST - 1, }; /* * enum qca_wlan_vendor_tx_latency_type - Represents the possible latency * types. * * @QCA_WLAN_VENDOR_TX_LATENCY_TYPE_DRIVER: Per MSDU latency * from: An MSDU is presented to the driver * to: the MSDU is queued into TCL SRNG * * @QCA_WLAN_VENDOR_TX_LATENCY_TYPE_RING: Per MSDU latency * from: the MSDU is queued into TCL SRNG * to: the MSDU is released by the driver * * @QCA_WLAN_VENDOR_TX_LATENCY_TYPE_HW: Per MSDU latency * from: the MSDU is presented to the hardware * to: the MSDU is released by the hardware * * @QCA_WLAN_VENDOR_TX_LATENCY_TYPE_CCA: Per PPDU latency * The time spent on Clear Channel Assessment, the maximum value is 50000 (us) * from: A PPDU is presented to the hardware LMAC * to: over-the-air transmission is started for the PPDU */ enum qca_wlan_vendor_tx_latency_type { QCA_WLAN_VENDOR_TX_LATENCY_TYPE_DRIVER = 0, QCA_WLAN_VENDOR_TX_LATENCY_TYPE_RING = 1, QCA_WLAN_VENDOR_TX_LATENCY_TYPE_HW = 2, QCA_WLAN_VENDOR_TX_LATENCY_TYPE_CCA = 3, }; /** * enum qca_wlan_vendor_attr_tx_latency_bucket - Definition of attributes * used inside nested attributes * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKETS and * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_STAT_BUCKETS. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE: u8 attribute. * Indicates the latency type. * See enum qca_wlan_vendor_tx_latency_type for the supported types. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_GRANULARITY: u32 attribute. * Indicates the granularity (in microseconds) of the distribution for the * type (specified by %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE), the value * must be positive. * If %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE is * %QCA_WLAN_VENDOR_TX_LATENCY_TYPE_CCA, the value must be an integer multiple * of 1000, and the maximum allowed value is 15000 (us). * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_AVERAGE: u32 attribute. * Indicates the average of the latency (in microseconds) for the type * (specified by %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE) within a cycle. * If there is no transmitted MSDUs/MPDUs during a cycle, this average is 0; * otherwise, it represents the quotient of divided by . * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_DISTRIBUTION: * Array of u32, 4 elements in total, represents the latency distribution for * the type (specified by %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE). * Each element holds the count of MSDUs/PPDUs (according to the latency type) * within a range: * element[0]: latency >= 0 && latency < granularity * element[1]: latency >= granularity && latency < granularity * 2 * element[2]: latency >= granularity * 2 && latency < granularity * 3 * element[3]: latency >= granularity * 3 */ enum qca_wlan_vendor_attr_tx_latency_bucket { QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE = 1, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_GRANULARITY = 2, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_AVERAGE = 3, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_DISTRIBUTION = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_MAX = QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tx_latency_link - Definition of attributes * used inside nested attribute %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAC_REMOTE: 6-byte MAC address. * Indicates link MAC address of the remote peer. For example, when running * in station mode, it's the BSSID of the link; while when running in AP * mode, it's the link MAC address of the remote station. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_STAT_BUCKETS: * Array of nested attribute. * Represents the transmit latency statistics for the link specified by * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAC_REMOTE. * Each entry represents the statistics for one of the types defined in * enum qca_wlan_vendor_tx_latency_type. * Each defined type has and must have one entry. * See enum qca_wlan_vendor_attr_tx_latency_bucket for nested attributes. */ enum qca_wlan_vendor_attr_tx_latency_link { QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAC_REMOTE = 1, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_STAT_BUCKETS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAX = QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_tx_latency_action - Represents the possible actions * for %QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY. * * @QCA_WLAN_VENDOR_TX_LATENCY_ACTION_DISABLE: * Disable transmit latency monitoring. * * @QCA_WLAN_VENDOR_TX_LATENCY_ACTION_ENABLE: * Enable transmit latency monitoring. * * @QCA_WLAN_VENDOR_TX_LATENCY_ACTION_GET: * Get transmit latency statistics of the last cycle (period is specified by * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIOD). */ enum qca_wlan_vendor_tx_latency_action { QCA_WLAN_VENDOR_TX_LATENCY_ACTION_DISABLE = 0, QCA_WLAN_VENDOR_TX_LATENCY_ACTION_ENABLE = 1, QCA_WLAN_VENDOR_TX_LATENCY_ACTION_GET = 2, }; /** * enum qca_wlan_vendor_attr_tx_latency - Definition of attributes used by * %QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY to configure, retrieve, and report * per-link transmit latency statistics. * * There are 6 uses of %QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY: * 1) used as a command to enable the feature * Precondition(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION is * %QCA_WLAN_VENDOR_TX_LATENCY_ACTION_ENABLE * Mandatory attribute(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIOD, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKETS with nested attributes * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_GRANULARITY. * Notes: * The driver will monitor the transmit latency for the active links * and save the statistics for each cycle (period is set by * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIOD) when the feature is enabled. * Set flag %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIODIC_REPORT if periodical * report is required. * * 2) used as a command to disable the feature * Precondition(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION is * %QCA_WLAN_VENDOR_TX_LATENCY_ACTION_DISABLE * Mandatory attribute(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION * * 3) used as a command to retrieve the statistics for all the active links on * the requested interface * Precondition(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION is * QCA_WLAN_VENDOR_TX_LATENCY_ACTION_GET and * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS is NOT present. * Mandatory attribute(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION * Notes: * The driver returns failure directly if the feature is not enabled or * there is no active link. * The driver returns the statistics of the last cycle in the case of * success. * * 4) used as a command to retrieve the statistics for the specified links * Precondition(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION is * QCA_WLAN_VENDOR_TX_LATENCY_ACTION_GET and * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS is present. * Mandatory attribute(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS, with nested attribute * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAC_REMOTE. * Notes: * The driver returns failure directly if the feature is not enabled or * any of the links (specified by %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS) * does not exist or is not in active state. * * 5) used as a command response for #3 or #4 * Precondition(s): * Userspace issues command #3 or #4, and the driver gets corresponding * statistics successfully. * Mandatory attribute(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS, with nested attributes * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAC_REMOTE, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_STAT_BUCKETS with nested * attributes %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_GRANULARITY, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_AVERAGE and * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_DISTRIBUTION. * * 6) used as an asynchronous event to report the statistics periodically * Precondition(s): * Userspace set flag %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIODIC_REPORT in * #1. * One or more links are in active state. * Mandatory attribute(s): * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS, with nested attributes * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_MAC_REMOTE, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINK_STAT_BUCKETS with nested * attributes %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_TYPE, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_GRANULARITY, * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_AVERAGE and * %QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKET_DISTRIBUTION. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_INVALID: Invalid attribute * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION: u32 attribute. * Action to take in this vendor command. * See enum qca_wlan_vendor_tx_latency_action for supported actions. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIODIC_REPORT: Flag attribute. * Enable (flag attribute present) - The driver needs to report transmit latency * statistics at the end of each statistical period. * Disable (flag attribute not present) - The driver doesn't need to report * transmit latency statistics periodically. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIOD: u32 attribute. * Indicates statistical period for transmit latency in terms of milliseconds, * the minimal allowed value is 100 and the maximum allowed value is 60000. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKETS: Array of nested attribute. * Each entry represents the latency buckets configuration for one of the types * defined in enum qca_wlan_vendor_tx_latency_type. * Each defined type has and must have one entry. * See enum qca_wlan_vendor_attr_tx_latency_bucket for the list of * supported attributes. * * @QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS: Array of nested attribute. * Information of the links, each entry represents for one link. * See enum qca_wlan_vendor_attr_tx_latency_link for the list of * supported attributes for each entry. */ enum qca_wlan_vendor_attr_tx_latency { QCA_WLAN_VENDOR_ATTR_TX_LATENCY_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_ACTION = 1, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIODIC_REPORT = 2, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_PERIOD = 3, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_BUCKETS = 4, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_LINKS = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_TX_LATENCY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TX_LATENCY_MAX = QCA_WLAN_VENDOR_ATTR_TX_LATENCY_AFTER_LAST - 1, }; /** * qca_wlan_vendor_attr_RECONFIG_REMOVE_COMPLETE_EVENT - Defines attributes for * ML Reconfig (Mlo Link removal) parameters used by the attribute * @QCA_WLAN_VENDOR_ATTR_RECONFIG_REMOVE_COMPLETE_EVENT_IFINDEX: u32 attribute * used to pass the netdev ifindex of the MLO Reconfiguration link. */ enum qca_wlan_vendor_attr_reconfig_remove_complete_EVENT { QCA_WLAN_VENDOR_ATTR_RECONFIG_REMOVE_COMPLETE_EVENT_IFINDEX = 0, /* keep last */ QCA_WLAN_VENDOR_ATTR_RECONFIG_REMOVE_COMPLETE_EVENT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RECONFIG_REMOVE_COMPLETE_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_RECONFIG_REMOVE_COMPLETE_EVENT_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tpc_pwr_level - Definition of attributes * used inside nested attribute %QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL. * * @QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_FREQUENCY: u32 channel center * frequency (MHz): If PSD power, carries one 20 MHz sub-channel center * frequency. If non PSD power, carries either 20 MHz bandwidth's center * channel frequency or 40 MHz bandwidth's center channel frequency * (or 80/160 MHz bandwidth's center channel frequency). * * @QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_TX_POWER: s8 transmit power limit (dBm). * If PSD power, carries PSD power value of the * QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_FREQUENCY mentioned sub-channel. * If non PSD power, carries EIRP power value of bandwidth mentioned * by QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_FREQUENCY center frequency. */ enum qca_wlan_vendor_attr_tpc_pwr_level { QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_FREQUENCY = 1, QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_TX_POWER = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_MAX = QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_tpc - Definition of link attributes * used inside nested attribute %QCA_WLAN_VENDOR_ATTR_TPC_LINKS. * * @QCA_WLAN_VENDOR_ATTR_TPC_BSSID: 6-bytes AP BSSID. * For MLO STA, AP BSSID indicates the AP's link address. * * @QCA_WLAN_VENDOR_ATTR_TPC_PSD_POWER: PSD power flag * Indicates using PSD power mode if this flag is present. * * @QCA_WLAN_VENDOR_ATTR_TPC_EIRP_POWER: s8 Regulatory EIRP power * value in dBm * * @QCA_WLAN_VENDOR_ATTR_TPC_POWER_TYPE_6GHZ: u8 power type of 6 GHz * AP, refer to Table E-12-Regulatory Info subfield encoding in * IEEE P802.11-REVme/D4.0. Only present if link is connected to 6 GHz AP. * * @QCA_WLAN_VENDOR_ATTR_TPC_AP_CONSTRAINT_POWER: u8 Local Power Constraint * (dBm) advertised by AP in Power Constraint element, refer to * IEEE Std 802.11-2020, 9.4.2.13 Power Constraint element. * * @QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL: A nested attribute containing * attributes defined by enum qca_wlan_vendor_attr_tpc_pwr_level. * If PSD power, each power level describes each 20 MHz subchannel PSD * power value. If non PSD power, each power level describes each supported * bandwidth's EIRP power value (up to Max bandwidth of AP operating on), * each level attribute contains corresponding bandwidth's center channel * frequency and its EIRP power value. */ enum qca_wlan_vendor_attr_tpc { QCA_WLAN_VENDOR_ATTR_TPC_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TPC_BSSID = 1, QCA_WLAN_VENDOR_ATTR_TPC_PSD_POWER = 2, QCA_WLAN_VENDOR_ATTR_TPC_EIRP_POWER = 3, QCA_WLAN_VENDOR_ATTR_TPC_POWER_TYPE_6GHZ = 4, QCA_WLAN_VENDOR_ATTR_TPC_AP_CONSTRAINT_POWER = 5, QCA_WLAN_VENDOR_ATTR_TPC_PWR_LEVEL = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_TPC_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TPC_MAX = QCA_WLAN_VENDOR_ATTR_TPC_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tpc_links - Definition of attributes * for %QCA_NL80211_VENDOR_SUBCMD_REGULATORY_TPC_INFO subcommand * * @QCA_WLAN_VENDOR_ATTR_TPC_LINKS: A nested attribute containing * per-link TPC information of all the active links of MLO STA. * For non MLO STA, only one link TPC information will be returned * for connected AP in this nested attribute. * The attributes used inside this nested attributes are defined * in enum qca_wlan_vendor_attr_tpc. */ enum qca_wlan_vendor_attr_tpc_links { QCA_WLAN_VENDOR_ATTR_TPC_LINKS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TPC_LINKS = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_TPC_LINKS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TPC_LINKS_MAX = QCA_WLAN_VENDOR_ATTR_TPC_AFTER_LAST - 1, }; /** * enum qca_wlan_btm_support: BTM support configuration * * @QCA_WLAN_BTM_SUPPORT_DEFAULT: Restore default BTM support policy. The driver * follows the BSS Transition bit in the Extended Capabilities element from the * connect request IEs with the default BTM support policy. * * @QCA_WLAN_BTM_SUPPORT_DISABLE: Disable BTM support for the subsequent * (re)association attempts. The driver shall restore the default BTM support * policy during the first disconnection after successful association. When this * configuration is enabled, the driver shall overwrite the BSS Transition bit * as zero in the Extended Capabilities element while sending (Re)Association * Request frames. Also, the driver shall drop the BTM frames from userspace and * the connected AP when this configuration is enabled. */ enum qca_wlan_btm_support { QCA_WLAN_BTM_SUPPORT_DEFAULT = 0, QCA_WLAN_BTM_SUPPORT_DISABLE = 1, }; #endif