linux/usb/pd_vdo.h

24  * <15>     :: VDM type ( 1b == structured, 0b == unstructured )
29  * <5>      :: reserved (SVDM), command type (UVDM)
52 #define VDO_SRC_INITIATOR	(0 << 5)
53 #define VDO_SRC_RESPONDER	(1 << 5)
59 #define CMD_EXIT_MODE		5
68 #define VDO_CMD_REBOOT		VDO_CMD_VENDOR(5)
91  * Power Delivery 3.0. Active Cables in Power Delivery 3.0 have 5 data objects.
98  * [5] :: Cable VDO 2
108 #define VDO_INDEX_CABLE_2	5
116  * <26>     :: modal operation supported (1b == yes)
131 #define IDH_PTYPE_AMA		5
184  * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
187  * <7>     :: Vconn required (AMA only, 0b == no, 1b == yes)
188  * <6>     :: Vbus required (AMA only, 0b == yes, 1b == no)
189  * <5:3>   :: Alternate modes
213 #define AMA_VCONN_PWR_5W	5
247  * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
248  * <21:5>  :: Reserved
270  * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive)
273  * <12:11> :: cable termination type (11b == both ends active VCONN req)
274  * <10>    :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
278  * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
279  * <4>     :: Vbus through cable (0b == no, 1b == yes)
280  * <3>     :: SOP" controller present? (0b == no, 1b == yes)
289  * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive)
292  * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req)
293  * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
295  * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
305  * <19:18> :: Connector type (10b == C, 11b == Captive)
308  * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req)
309  * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
310  * <8>     :: SBU supported (0b == supported, 1b == not supported)
311  * <7>     :: SBU type (0b == passive, 1b == active)
312  * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
313  * <4>     :: Vbus through cable (0b == no, 1b == yes)
314  * <3>     :: SOP" controller present? (0b == no, 1b == yes)
332 #define CABLE_LATENCY_5M	5
374 	 | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5		\
379 	 | ((vbm) & 0x3) << 9 | ((cur) & 0x3) << 5 | ((spd) & 0x7))
383 	 | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5	\
396  * <11>    :: U3 to U0 transition mode (0b == direct, 1b == through U3S)
397  * <10>    :: Physical connection (0b == copper, 1b == optical)
398  * <9>     :: Active element (0b == redriver, 1b == retimer)
399  * <8>     :: USB4 supported (0b == yes, 1b == no)
401  * <5>     :: USB2 supported (0b == yes, 1b == no)
402  * <4>     :: USB3.2 supported (0b == yes, 1b == no)
403  * <3>     :: USB lanes supported (0b == one lane, 1b == two lanes)
404  * <2>     :: Optically isolated active cable (0b == no, 1b == yes)
406  * <0>     :: USB gen (0b == gen1, 1b == gen2+)
414 #define ACAB2_U3_CLD_200UW	5
440 	 | ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3		\
449  * <11>    :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
453  * <7:5>   :: Vconn power
461 	 | ((vcpwr) & 0x7) << 5 | (vcr) << 4 | (vbr) << 3		\
479  * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
480  * <14>    :: Charge through current support (0b == 3A, 1b == 5A)
484  * <0>     :: Charge through support (0b == no, 1b == yes)