Lines Matching +full:0 +full:x00000700
10 #define BCMA_CC_ID 0x0000
11 #define BCMA_CC_ID_ID 0x0000FFFF
12 #define BCMA_CC_ID_ID_SHIFT 0
13 #define BCMA_CC_ID_REV 0x000F0000
15 #define BCMA_CC_ID_PKG 0x00F00000
17 #define BCMA_CC_ID_NRCORES 0x0F000000
19 #define BCMA_CC_ID_TYPE 0xF0000000
21 #define BCMA_CC_CAP 0x0004 /* Capabilities */
22 #define BCMA_CC_CAP_NRUART 0x00000003 /* # of UARTs */
23 #define BCMA_CC_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */
24 #define BCMA_CC_CAP_UARTCLK 0x00000018 /* UART clock select */
25 #define BCMA_CC_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */
26 #define BCMA_CC_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */
27 #define BCMA_CC_CAP_EXTBUS 0x000000C0 /* External buses present */
28 #define BCMA_CC_CAP_FLASHT 0x00000700 /* Flash Type */
29 #define BCMA_CC_FLASHT_NONE 0x00000000 /* No flash */
30 #define BCMA_CC_FLASHT_STSER 0x00000100 /* ST serial flash */
31 #define BCMA_CC_FLASHT_ATSER 0x00000200 /* Atmel serial flash */
32 #define BCMA_CC_FLASHT_NAND 0x00000300 /* NAND flash */
33 #define BCMA_CC_FLASHT_PARA 0x00000700 /* Parallel flash */
34 #define BCMA_CC_CAP_PLLT 0x00038000 /* PLL Type */
35 #define BCMA_PLLTYPE_NONE 0x00000000
36 #define BCMA_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */
37 #define BCMA_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */
38 #define BCMA_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */
39 #define BCMA_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */
40 #define BCMA_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */
41 #define BCMA_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */
42 #define BCMA_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */
43 #define BCMA_CC_CAP_PCTL 0x00040000 /* Power Control */
44 #define BCMA_CC_CAP_OTPS 0x00380000 /* OTP size */
47 #define BCMA_CC_CAP_JTAGM 0x00400000 /* JTAG master present */
48 #define BCMA_CC_CAP_BROM 0x00800000 /* Internal boot ROM active */
49 #define BCMA_CC_CAP_64BIT 0x08000000 /* 64-bit Backplane */
50 #define BCMA_CC_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
51 #define BCMA_CC_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
52 #define BCMA_CC_CAP_SPROM 0x40000000 /* SPROM present */
53 #define BCMA_CC_CAP_NFLASH 0x80000000 /* NAND flash present (rev >= 35 or BCM4706?) */
54 #define BCMA_CC_CORECTL 0x0008
55 #define BCMA_CC_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
56 #define BCMA_CC_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
57 #define BCMA_CC_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */
58 #define BCMA_CC_BIST 0x000C
59 #define BCMA_CC_OTPS 0x0010 /* OTP status */
60 #define BCMA_CC_OTPS_PROGFAIL 0x80000000
61 #define BCMA_CC_OTPS_PROTECT 0x00000007
62 #define BCMA_CC_OTPS_HW_PROTECT 0x00000001
63 #define BCMA_CC_OTPS_SW_PROTECT 0x00000002
64 #define BCMA_CC_OTPS_CID_PROTECT 0x00000004
65 #define BCMA_CC_OTPS_GU_PROG_IND 0x00000F00 /* General Use programmed indication */
67 #define BCMA_CC_OTPS_GU_PROG_HW 0x00000100 /* HW region programmed */
68 #define BCMA_CC_OTPC 0x0014 /* OTP control */
69 #define BCMA_CC_OTPC_RECWAIT 0xFF000000
70 #define BCMA_CC_OTPC_PROGWAIT 0x00FFFF00
72 #define BCMA_CC_OTPC_MAXFAIL 0x00000038
73 #define BCMA_CC_OTPC_VSEL 0x00000006
74 #define BCMA_CC_OTPC_SELVL 0x00000001
75 #define BCMA_CC_OTPP 0x0018 /* OTP prog */
76 #define BCMA_CC_OTPP_COL 0x000000FF
77 #define BCMA_CC_OTPP_ROW 0x0000FF00
79 #define BCMA_CC_OTPP_READERR 0x10000000
80 #define BCMA_CC_OTPP_VALUE 0x20000000
81 #define BCMA_CC_OTPP_READ 0x40000000
82 #define BCMA_CC_OTPP_START 0x80000000
83 #define BCMA_CC_OTPP_BUSY 0x80000000
84 #define BCMA_CC_OTPL 0x001C /* OTP layout */
85 #define BCMA_CC_OTPL_GURGN_OFFSET 0x00000FFF /* offset of general use region */
86 #define BCMA_CC_IRQSTAT 0x0020
87 #define BCMA_CC_IRQMASK 0x0024
88 #define BCMA_CC_IRQ_GPIO 0x00000001 /* gpio intr */
89 #define BCMA_CC_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */
90 #define BCMA_CC_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */
91 #define BCMA_CC_CHIPCTL 0x0028 /* Rev >= 11 only */
92 #define BCMA_CC_CHIPSTAT 0x002C /* Rev >= 11 only */
97 #define BCMA_CC_CHIPST_43228_ILP_DIV_EN 0x00000001
98 #define BCMA_CC_CHIPST_43228_OTP_PRESENT 0x00000002
99 #define BCMA_CC_CHIPST_43228_SERDES_REFCLK_PADSEL 0x00000004
100 #define BCMA_CC_CHIPST_43228_SDIO_MODE 0x00000008
101 #define BCMA_CC_CHIPST_43228_SDIO_OTP_PRESENT 0x00000010
102 #define BCMA_CC_CHIPST_43228_SDIO_RESET 0x00000020
103 #define BCMA_CC_CHIPST_4706_PKG_OPTION BIT(0) /* 0: full-featured package 1: low-cost package */
104 #define BCMA_CC_CHIPST_4706_SFLASH_PRESENT BIT(1) /* 0: parallel, 1: serial flash is present */
105 #define BCMA_CC_CHIPST_4706_SFLASH_TYPE BIT(2) /* 0: 8b-p/ST-s flash, 1: 16b-p/Atmal-s flash */
106 #define BCMA_CC_CHIPST_4706_MIPS_BENDIAN BIT(3) /* 0: little, 1: big endian */
109 #define BCMA_CC_CHIPST_4360_XTAL_40MZ 0x00000001
110 #define BCMA_CC_JCMD 0x0030 /* Rev >= 10 only */
111 #define BCMA_CC_JCMD_START 0x80000000
112 #define BCMA_CC_JCMD_BUSY 0x80000000
113 #define BCMA_CC_JCMD_PAUSE 0x40000000
114 #define BCMA_CC_JCMD0_ACC_MASK 0x0000F000
115 #define BCMA_CC_JCMD0_ACC_IRDR 0x00000000
116 #define BCMA_CC_JCMD0_ACC_DR 0x00001000
117 #define BCMA_CC_JCMD0_ACC_IR 0x00002000
118 #define BCMA_CC_JCMD0_ACC_RESET 0x00003000
119 #define BCMA_CC_JCMD0_ACC_IRPDR 0x00004000
120 #define BCMA_CC_JCMD0_ACC_PDR 0x00005000
121 #define BCMA_CC_JCMD0_IRW_MASK 0x00000F00
122 #define BCMA_CC_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */
123 #define BCMA_CC_JCMD_ACC_IRDR 0x00000000
124 #define BCMA_CC_JCMD_ACC_DR 0x00010000
125 #define BCMA_CC_JCMD_ACC_IR 0x00020000
126 #define BCMA_CC_JCMD_ACC_RESET 0x00030000
127 #define BCMA_CC_JCMD_ACC_IRPDR 0x00040000
128 #define BCMA_CC_JCMD_ACC_PDR 0x00050000
129 #define BCMA_CC_JCMD_IRW_MASK 0x00001F00
131 #define BCMA_CC_JCMD_DRW_MASK 0x0000003F
132 #define BCMA_CC_JIR 0x0034 /* Rev >= 10 only */
133 #define BCMA_CC_JDR 0x0038 /* Rev >= 10 only */
134 #define BCMA_CC_JCTL 0x003C /* Rev >= 10 only */
138 #define BCMA_CC_FLASHCTL 0x0040
140 #define BCMA_CC_FLASHCTL_OPCODE 0x000000ff
141 #define BCMA_CC_FLASHCTL_ACTION 0x00000700
142 #define BCMA_CC_FLASHCTL_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */
143 #define BCMA_CC_FLASHCTL_START 0x80000000
146 #define BCMA_CC_FLASHCTL_ST_WREN 0x0006 /* Write Enable */
147 #define BCMA_CC_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */
148 #define BCMA_CC_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */
149 #define BCMA_CC_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */
150 #define BCMA_CC_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */
151 #define BCMA_CC_FLASHCTL_ST_PP 0x0302 /* Page Program */
152 #define BCMA_CC_FLASHCTL_ST_SE 0x02d8 /* Sector Erase */
153 #define BCMA_CC_FLASHCTL_ST_BE 0x00c7 /* Bulk Erase */
154 #define BCMA_CC_FLASHCTL_ST_DP 0x00b9 /* Deep Power-down */
155 #define BCMA_CC_FLASHCTL_ST_RES 0x03ab /* Read Electronic Signature */
156 #define BCMA_CC_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */
157 #define BCMA_CC_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */
159 #define BCMA_CC_FLASHCTL_AT_READ 0x07e8
160 #define BCMA_CC_FLASHCTL_AT_PAGE_READ 0x07d2
161 #define BCMA_CC_FLASHCTL_AT_STATUS 0x01d7
162 #define BCMA_CC_FLASHCTL_AT_BUF1_WRITE 0x0384
163 #define BCMA_CC_FLASHCTL_AT_BUF2_WRITE 0x0387
164 #define BCMA_CC_FLASHCTL_AT_BUF1_ERASE_PROGRAM 0x0283
165 #define BCMA_CC_FLASHCTL_AT_BUF2_ERASE_PROGRAM 0x0286
166 #define BCMA_CC_FLASHCTL_AT_BUF1_PROGRAM 0x0288
167 #define BCMA_CC_FLASHCTL_AT_BUF2_PROGRAM 0x0289
168 #define BCMA_CC_FLASHCTL_AT_PAGE_ERASE 0x0281
169 #define BCMA_CC_FLASHCTL_AT_BLOCK_ERASE 0x0250
170 #define BCMA_CC_FLASHCTL_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382
171 #define BCMA_CC_FLASHCTL_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385
172 #define BCMA_CC_FLASHCTL_AT_BUF1_LOAD 0x0253
173 #define BCMA_CC_FLASHCTL_AT_BUF2_LOAD 0x0255
174 #define BCMA_CC_FLASHCTL_AT_BUF1_COMPARE 0x0260
175 #define BCMA_CC_FLASHCTL_AT_BUF2_COMPARE 0x0261
176 #define BCMA_CC_FLASHCTL_AT_BUF1_REPROGRAM 0x0258
177 #define BCMA_CC_FLASHCTL_AT_BUF2_REPROGRAM 0x0259
178 #define BCMA_CC_FLASHADDR 0x0044
179 #define BCMA_CC_FLASHDATA 0x0048
181 #define BCMA_CC_FLASHDATA_ST_WIP 0x01 /* Write In Progress */
182 #define BCMA_CC_FLASHDATA_ST_WEL 0x02 /* Write Enable Latch */
183 #define BCMA_CC_FLASHDATA_ST_BP_MASK 0x1c /* Block Protect */
185 #define BCMA_CC_FLASHDATA_ST_SRWD 0x80 /* Status Register Write Disable */
187 #define BCMA_CC_FLASHDATA_AT_READY 0x80
188 #define BCMA_CC_FLASHDATA_AT_MISMATCH 0x40
189 #define BCMA_CC_FLASHDATA_AT_ID_MASK 0x38
191 #define BCMA_CC_BCAST_ADDR 0x0050
192 #define BCMA_CC_BCAST_DATA 0x0054
193 #define BCMA_CC_GPIOPULLUP 0x0058 /* Rev >= 20 only */
194 #define BCMA_CC_GPIOPULLDOWN 0x005C /* Rev >= 20 only */
195 #define BCMA_CC_GPIOIN 0x0060
196 #define BCMA_CC_GPIOOUT 0x0064
197 #define BCMA_CC_GPIOOUTEN 0x0068
198 #define BCMA_CC_GPIOCTL 0x006C
199 #define BCMA_CC_GPIOPOL 0x0070
200 #define BCMA_CC_GPIOIRQ 0x0074
201 #define BCMA_CC_WATCHDOG 0x0080
202 #define BCMA_CC_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */
203 #define BCMA_CC_GPIOTIMER_OFFTIME 0x0000FFFF
204 #define BCMA_CC_GPIOTIMER_OFFTIME_SHIFT 0
205 #define BCMA_CC_GPIOTIMER_ONTIME 0xFFFF0000
207 #define BCMA_CC_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */
208 #define BCMA_CC_CLOCK_N 0x0090
209 #define BCMA_CC_CLOCK_SB 0x0094
210 #define BCMA_CC_CLOCK_PCI 0x0098
211 #define BCMA_CC_CLOCK_M2 0x009C
212 #define BCMA_CC_CLOCK_MIPS 0x00A0
213 #define BCMA_CC_CLKDIV 0x00A4 /* Rev >= 3 only */
214 #define BCMA_CC_CLKDIV_SFLASH 0x0F000000
216 #define BCMA_CC_CLKDIV_OTP 0x000F0000
218 #define BCMA_CC_CLKDIV_JTAG 0x00000F00
220 #define BCMA_CC_CLKDIV_UART 0x000000FF
221 #define BCMA_CC_CAP_EXT 0x00AC /* Capabilities */
222 #define BCMA_CC_CAP_EXT_SECI_PRESENT 0x00000001
223 #define BCMA_CC_CAP_EXT_GSIO_PRESENT 0x00000002
224 #define BCMA_CC_CAP_EXT_GCI_PRESENT 0x00000004
225 #define BCMA_CC_CAP_EXT_SECI_PUART_PRESENT 0x00000008 /* UART present */
226 #define BCMA_CC_CAP_EXT_AOB_PRESENT 0x00000040
227 #define BCMA_CC_PLLONDELAY 0x00B0 /* Rev >= 4 only */
228 #define BCMA_CC_FREFSELDELAY 0x00B4 /* Rev >= 4 only */
229 #define BCMA_CC_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */
230 #define BCMA_CC_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */
231 #define BCMA_CC_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */
232 #define BCMA_CC_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */
233 #define BCMA_CC_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */
234 #define BCMA_CC_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */
235 #define BCMA_CC_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled…
236 #define BCMA_CC_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0:…
237 #define BCMA_CC_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL…
238 #define BCMA_CC_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disab…
239 #define BCMA_CC_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */
240 #define BCMA_CC_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */
242 #define BCMA_CC_SYSCLKCTL 0x00C0 /* Rev >= 3 only */
243 #define BCMA_CC_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */
244 #define BCMA_CC_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */
245 #define BCMA_CC_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */
246 #define BCMA_CC_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */
247 #define BCMA_CC_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */
248 #define BCMA_CC_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */
250 #define BCMA_CC_CLKSTSTR 0x00C4 /* Rev >= 3 only */
251 #define BCMA_CC_EROM 0x00FC
252 #define BCMA_CC_PCMCIA_CFG 0x0100
253 #define BCMA_CC_PCMCIA_MEMWAIT 0x0104
254 #define BCMA_CC_PCMCIA_ATTRWAIT 0x0108
255 #define BCMA_CC_PCMCIA_IOWAIT 0x010C
256 #define BCMA_CC_IDE_CFG 0x0110
257 #define BCMA_CC_IDE_MEMWAIT 0x0114
258 #define BCMA_CC_IDE_ATTRWAIT 0x0118
259 #define BCMA_CC_IDE_IOWAIT 0x011C
260 #define BCMA_CC_PROG_CFG 0x0120
261 #define BCMA_CC_PROG_WAITCNT 0x0124
262 #define BCMA_CC_FLASH_CFG 0x0128
263 #define BCMA_CC_FLASH_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */
264 #define BCMA_CC_FLASH_WAITCNT 0x012C
265 #define BCMA_CC_SROM_CONTROL 0x0190
266 #define BCMA_CC_SROM_CONTROL_START 0x80000000
267 #define BCMA_CC_SROM_CONTROL_BUSY 0x80000000
268 #define BCMA_CC_SROM_CONTROL_OPCODE 0x60000000
269 #define BCMA_CC_SROM_CONTROL_OP_READ 0x00000000
270 #define BCMA_CC_SROM_CONTROL_OP_WRITE 0x20000000
271 #define BCMA_CC_SROM_CONTROL_OP_WRDIS 0x40000000
272 #define BCMA_CC_SROM_CONTROL_OP_WREN 0x60000000
273 #define BCMA_CC_SROM_CONTROL_OTPSEL 0x00000010
274 #define BCMA_CC_SROM_CONTROL_OTP_PRESENT 0x00000020
275 #define BCMA_CC_SROM_CONTROL_LOCK 0x00000008
276 #define BCMA_CC_SROM_CONTROL_SIZE_MASK 0x00000006
277 #define BCMA_CC_SROM_CONTROL_SIZE_1K 0x00000000
278 #define BCMA_CC_SROM_CONTROL_SIZE_4K 0x00000002
279 #define BCMA_CC_SROM_CONTROL_SIZE_16K 0x00000004
281 #define BCMA_CC_SROM_CONTROL_PRESENT 0x00000001
282 /* Block 0x140 - 0x190 registers are chipset specific */
283 #define BCMA_CC_4706_FLASHSCFG 0x18C /* Flash struct configuration */
284 #define BCMA_CC_4706_FLASHSCFG_MASK 0x000000ff
285 #define BCMA_CC_4706_FLASHSCFG_SF1 0x00000001 /* 2nd serial flash present */
286 #define BCMA_CC_4706_FLASHSCFG_PF1 0x00000002 /* 2nd parallel flash present */
287 #define BCMA_CC_4706_FLASHSCFG_SF1_TYPE 0x00000004 /* 2nd serial flash type : 0 : ST, 1 : Atmel */
288 #define BCMA_CC_4706_FLASHSCFG_NF1 0x00000008 /* 2nd NAND flash present */
289 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_MASK 0x000000f0
290 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_4MB 0x00000010 /* 4MB */
291 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_8MB 0x00000020 /* 8MB */
292 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_16MB 0x00000030 /* 16MB */
293 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_32MB 0x00000040 /* 32MB */
294 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_64MB 0x00000050 /* 64MB */
295 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_128MB 0x00000060 /* 128MB */
296 #define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_256MB 0x00000070 /* 256MB */
298 #define BCMA_CC_NFLASH_CTL 0x01A0
299 #define BCMA_CC_NFLASH_CTL_ERR 0x08000000
300 #define BCMA_CC_NFLASH_CONF 0x01A4
301 #define BCMA_CC_NFLASH_COL_ADDR 0x01A8
302 #define BCMA_CC_NFLASH_ROW_ADDR 0x01AC
303 #define BCMA_CC_NFLASH_DATA 0x01B0
304 #define BCMA_CC_NFLASH_WAITCNT0 0x01B4
305 /* 0x1E0 is defined as shared BCMA_CLKCTLST */
306 #define BCMA_CC_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */
307 #define BCMA_CC_UART0_DATA 0x0300
308 #define BCMA_CC_UART0_IMR 0x0304
309 #define BCMA_CC_UART0_FCR 0x0308
310 #define BCMA_CC_UART0_LCR 0x030C
311 #define BCMA_CC_UART0_MCR 0x0310
312 #define BCMA_CC_UART0_LSR 0x0314
313 #define BCMA_CC_UART0_MSR 0x0318
314 #define BCMA_CC_UART0_SCRATCH 0x031C
315 #define BCMA_CC_UART1_DATA 0x0400
316 #define BCMA_CC_UART1_IMR 0x0404
317 #define BCMA_CC_UART1_FCR 0x0408
318 #define BCMA_CC_UART1_LCR 0x040C
319 #define BCMA_CC_UART1_MCR 0x0410
320 #define BCMA_CC_UART1_LSR 0x0414
321 #define BCMA_CC_UART1_MSR 0x0418
322 #define BCMA_CC_UART1_SCRATCH 0x041C
324 #define BCMA_CC_PMU_CTL 0x0600 /* PMU control */
325 #define BCMA_CC_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */
327 #define BCMA_CC_PMU_CTL_RES 0x00006000 /* reset control mask */
329 #define BCMA_CC_PMU_CTL_RES_RELOAD 0x2 /* reload POR values */
330 #define BCMA_CC_PMU_CTL_PLL_UPD 0x00000400
331 #define BCMA_CC_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */
332 #define BCMA_CC_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */
333 #define BCMA_CC_PMU_CTL_ALPREQEN 0x00000080 /* ALP req enable */
334 #define BCMA_CC_PMU_CTL_XTALFREQ 0x0000007C /* Crystal freq */
336 #define BCMA_CC_PMU_CTL_ILPDIVEN 0x00000002 /* ILP div enable */
337 #define BCMA_CC_PMU_CTL_LPOSEL 0x00000001 /* LPO sel */
338 #define BCMA_CC_PMU_CAP 0x0604 /* PMU capabilities */
339 #define BCMA_CC_PMU_CAP_REVISION 0x000000FF /* Revision mask */
340 #define BCMA_CC_PMU_STAT 0x0608 /* PMU status */
341 #define BCMA_CC_PMU_STAT_EXT_LPO_AVAIL 0x00000100
342 #define BCMA_CC_PMU_STAT_WDRESET 0x00000080
343 #define BCMA_CC_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */
344 #define BCMA_CC_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */
345 #define BCMA_CC_PMU_STAT_HAVEALP 0x00000008 /* ALP available */
346 #define BCMA_CC_PMU_STAT_HAVEHT 0x00000004 /* HT available */
347 #define BCMA_CC_PMU_STAT_RESINIT 0x00000003 /* Res init */
348 #define BCMA_CC_PMU_RES_STAT 0x060C /* PMU res status */
349 #define BCMA_CC_PMU_RES_PEND 0x0610 /* PMU res pending */
350 #define BCMA_CC_PMU_TIMER 0x0614 /* PMU timer */
351 #define BCMA_CC_PMU_MINRES_MSK 0x0618 /* PMU min res mask */
352 #define BCMA_CC_PMU_MAXRES_MSK 0x061C /* PMU max res mask */
353 #define BCMA_CC_PMU_RES_TABSEL 0x0620 /* PMU res table sel */
354 #define BCMA_CC_PMU_RES_DEPMSK 0x0624 /* PMU res dep mask */
355 #define BCMA_CC_PMU_RES_UPDNTM 0x0628 /* PMU res updown timer */
356 #define BCMA_CC_PMU_RES_TIMER 0x062C /* PMU res timer */
357 #define BCMA_CC_PMU_CLKSTRETCH 0x0630 /* PMU clockstretch */
358 #define BCMA_CC_PMU_WATCHDOG 0x0634 /* PMU watchdog */
359 #define BCMA_CC_PMU_RES_REQTS 0x0640 /* PMU res req timer sel */
360 #define BCMA_CC_PMU_RES_REQT 0x0644 /* PMU res req timer */
361 #define BCMA_CC_PMU_RES_REQM 0x0648 /* PMU res req mask */
362 #define BCMA_CC_PMU_CHIPCTL_ADDR 0x0650
363 #define BCMA_CC_PMU_CHIPCTL_DATA 0x0654
364 #define BCMA_CC_PMU_REGCTL_ADDR 0x0658
365 #define BCMA_CC_PMU_REGCTL_DATA 0x065C
366 #define BCMA_CC_PMU_PLLCTL_ADDR 0x0660
367 #define BCMA_CC_PMU_PLLCTL_DATA 0x0664
368 #define BCMA_CC_PMU_STRAPOPT 0x0668 /* (corerev >= 28) */
369 #define BCMA_CC_PMU_XTAL_FREQ 0x066C /* (pmurev >= 10) */
370 #define BCMA_CC_PMU_XTAL_FREQ_ILPCTL_MASK 0x00001FFF
371 #define BCMA_CC_PMU_XTAL_FREQ_MEASURE_MASK 0x80000000
373 #define BCMA_CC_SPROM 0x0800 /* SPROM beginning */
375 #define BCMA_CC_NAND_REVISION 0x0C00
376 #define BCMA_CC_NAND_CMD_START 0x0C04
377 #define BCMA_CC_NAND_CMD_ADDR_X 0x0C08
378 #define BCMA_CC_NAND_CMD_ADDR 0x0C0C
379 #define BCMA_CC_NAND_CMD_END_ADDR 0x0C10
380 #define BCMA_CC_NAND_CS_NAND_SELECT 0x0C14
381 #define BCMA_CC_NAND_CS_NAND_XOR 0x0C18
382 #define BCMA_CC_NAND_SPARE_RD0 0x0C20
383 #define BCMA_CC_NAND_SPARE_RD4 0x0C24
384 #define BCMA_CC_NAND_SPARE_RD8 0x0C28
385 #define BCMA_CC_NAND_SPARE_RD12 0x0C2C
386 #define BCMA_CC_NAND_SPARE_WR0 0x0C30
387 #define BCMA_CC_NAND_SPARE_WR4 0x0C34
388 #define BCMA_CC_NAND_SPARE_WR8 0x0C38
389 #define BCMA_CC_NAND_SPARE_WR12 0x0C3C
390 #define BCMA_CC_NAND_ACC_CONTROL 0x0C40
391 #define BCMA_CC_NAND_CONFIG 0x0C48
392 #define BCMA_CC_NAND_TIMING_1 0x0C50
393 #define BCMA_CC_NAND_TIMING_2 0x0C54
394 #define BCMA_CC_NAND_SEMAPHORE 0x0C58
395 #define BCMA_CC_NAND_DEVID 0x0C60
396 #define BCMA_CC_NAND_DEVID_X 0x0C64
397 #define BCMA_CC_NAND_BLOCK_LOCK_STATUS 0x0C68
398 #define BCMA_CC_NAND_INTFC_STATUS 0x0C6C
399 #define BCMA_CC_NAND_ECC_CORR_ADDR_X 0x0C70
400 #define BCMA_CC_NAND_ECC_CORR_ADDR 0x0C74
401 #define BCMA_CC_NAND_ECC_UNC_ADDR_X 0x0C78
402 #define BCMA_CC_NAND_ECC_UNC_ADDR 0x0C7C
403 #define BCMA_CC_NAND_READ_ERROR_COUNT 0x0C80
404 #define BCMA_CC_NAND_CORR_STAT_THRESHOLD 0x0C84
405 #define BCMA_CC_NAND_READ_ADDR_X 0x0C90
406 #define BCMA_CC_NAND_READ_ADDR 0x0C94
407 #define BCMA_CC_NAND_PAGE_PROGRAM_ADDR_X 0x0C98
408 #define BCMA_CC_NAND_PAGE_PROGRAM_ADDR 0x0C9C
409 #define BCMA_CC_NAND_COPY_BACK_ADDR_X 0x0CA0
410 #define BCMA_CC_NAND_COPY_BACK_ADDR 0x0CA4
411 #define BCMA_CC_NAND_BLOCK_ERASE_ADDR_X 0x0CA8
412 #define BCMA_CC_NAND_BLOCK_ERASE_ADDR 0x0CAC
413 #define BCMA_CC_NAND_INV_READ_ADDR_X 0x0CB0
414 #define BCMA_CC_NAND_INV_READ_ADDR 0x0CB4
415 #define BCMA_CC_NAND_BLK_WR_PROTECT 0x0CC0
416 #define BCMA_CC_NAND_ACC_CONTROL_CS1 0x0CD0
417 #define BCMA_CC_NAND_CONFIG_CS1 0x0CD4
418 #define BCMA_CC_NAND_TIMING_1_CS1 0x0CD8
419 #define BCMA_CC_NAND_TIMING_2_CS1 0x0CDC
420 #define BCMA_CC_NAND_SPARE_RD16 0x0D30
421 #define BCMA_CC_NAND_SPARE_RD20 0x0D34
422 #define BCMA_CC_NAND_SPARE_RD24 0x0D38
423 #define BCMA_CC_NAND_SPARE_RD28 0x0D3C
424 #define BCMA_CC_NAND_CACHE_ADDR 0x0D40
425 #define BCMA_CC_NAND_CACHE_DATA 0x0D44
426 #define BCMA_CC_NAND_CTRL_CONFIG 0x0D48
427 #define BCMA_CC_NAND_CTRL_STATUS 0x0D4C
438 #define BCMA_CC_PMU5356_MAINPLL_PLL0 0
439 #define BCMA_CC_PMU5357_MAINPLL_PLL0 0
442 #define BCMA_CC_PMU4706_MAINPLL_PLL0 0
444 #define BCMA_CC_PMU6_4706_PROC_P2DIV_MASK 0x000f0000
446 #define BCMA_CC_PMU6_4706_PROC_P1DIV_MASK 0x0000f000
448 #define BCMA_CC_PMU6_4706_PROC_NDIV_INT_MASK 0x00000ff8
450 #define BCMA_CC_PMU6_4706_PROC_NDIV_MODE_MASK 0x00000007
451 #define BCMA_CC_PMU6_4706_PROC_NDIV_MODE_SHIFT 0
454 #define BCMA_CC_PMU15_PLL_PLLCTL0 0
455 #define BCMA_CC_PMU15_PLL_PC0_CLKSEL_MASK 0x00000003
456 #define BCMA_CC_PMU15_PLL_PC0_CLKSEL_SHIFT 0
457 #define BCMA_CC_PMU15_PLL_PC0_FREQTGT_MASK 0x003FFFFC
459 #define BCMA_CC_PMU15_PLL_PC0_PRESCALE_MASK 0x00C00000
461 #define BCMA_CC_PMU15_PLL_PC0_KPCTRL_MASK 0x07000000
463 #define BCMA_CC_PMU15_PLL_PC0_FCNTCTRL_MASK 0x38000000
465 #define BCMA_CC_PMU15_PLL_PC0_FDCMODE_MASK 0x40000000
467 #define BCMA_CC_PMU15_PLL_PC0_CTRLBIAS_MASK 0x80000000
476 #define BCMA_CC_PPL_P1P2_OFF 0
477 #define BCMA_CC_PPL_P1_MASK 0x0f000000
479 #define BCMA_CC_PPL_P2_MASK 0x00f00000
482 #define BCMA_CC_PPL_MDIV_MASK 0x000000ff
485 #define BCMA_CC_PPL_NDIV_MASK 0xfff00000
488 #define BCMA_CC_PPL_MRAT_MASK 0xf0000000
490 #define BCMA_CC_PPL_ABRAT_MASK 0x08000000
492 #define BCMA_CC_PPL_FDIV_MASK 0x07ffffff
495 #define BCMA_CC_PPL_PCHI_MASK 0x0000003f
497 #define BCMA_CC_PMU_PLL_CTL0 0
504 #define BCMA_CC_PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000
507 #define BCMA_CC_PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000
510 #define BCMA_CCB_MII_MNG_CTL 0x0000
511 #define BCMA_CCB_MII_MNG_CMD_DATA 0x0004
514 #define BCMA_CHIPCTL_4331_BT_COEXIST BIT(0) /* 0 disable */
515 #define BCMA_CHIPCTL_4331_SECI BIT(1) /* 0 SECI is disabled (JATG functional) */
516 #define BCMA_CHIPCTL_4331_EXT_LNA BIT(2) /* 0 disable */
518 #define BCMA_CHIPCTL_4331_EXTPA_EN BIT(4) /* 0 ext pa disable, 1 ext pa enabled */
526 #define BCMA_CHIPCTL_4331_EXTPA_EN2 BIT(12) /* 0 ext pa disable, 1 ext pa enabled */
531 #define BCMA_CCTRL_43224_GPIO_TOGGLE 0x8000 /* gpio[3:0] pins as btcoex or s/w gpio */
532 #define BCMA_CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */
533 #define BCMA_CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */
536 #define BCMA_CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */
545 #define BCMA_RES_4314_LPLDO_PU BIT(0)