dt-bindings/usb/pd.h

103  * <26>     :: modal operation supported (1b == yes)
118 #define IDH_PTYPE_AMA           5
158  * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
161  * <7>     :: Vconn required (AMA only, 0b == no, 1b == yes)
162  * <6>     :: Vbus required (AMA only, 0b == yes, 1b == no)
163  * <5:3>   :: Alternate modes
185 #define AMA_VCONN_PWR_5W	5
219  * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
220  * <21:5>  :: Reserved
240  * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive)
243  * <12:11> :: cable termination type (11b == both ends active VCONN req)
244  * <10>    :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
248  * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
249  * <4>     :: Vbus through cable (0b == no, 1b == yes)
250  * <3>     :: SOP" controller present? (0b == no, 1b == yes)
259  * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive)
262  * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req)
263  * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
265  * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
275  * <19:18> :: Connector type (10b == C, 11b == Captive)
278  * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req)
279  * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
280  * <8>     :: SBU supported (0b == supported, 1b == not supported)
281  * <7>     :: SBU type (0b == passive, 1b == active)
282  * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
283  * <4>     :: Vbus through cable (0b == no, 1b == yes)
284  * <3>     :: SOP" controller present? (0b == no, 1b == yes)
302 #define CABLE_LATENCY_5M	5
344 	 | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5		\
349 	 | ((vbm) & 0x3) << 9 | ((cur) & 0x3) << 5 | ((spd) & 0x7))
353 	 | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5	\
363  * <11>    :: U3 to U0 transition mode (0b == direct, 1b == through U3S)
364  * <10>    :: Physical connection (0b == copper, 1b == optical)
365  * <9>     :: Active element (0b == redriver, 1b == retimer)
366  * <8>     :: USB4 supported (0b == yes, 1b == no)
368  * <5>     :: USB2 supported (0b == yes, 1b == no)
369  * <4>     :: USB3.2 supported (0b == yes, 1b == no)
370  * <3>     :: USB lanes supported (0b == one lane, 1b == two lanes)
371  * <2>     :: Optically isolated active cable (0b == no, 1b == yes)
373  * <0>     :: USB gen (0b == gen1, 1b == gen2+)
381 #define ACAB2_U3_CLD_200UW	5
407 	 | ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3		\
416  * <11>    :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
420  * <7:5>   :: Vconn power
428 	 | ((vcpwr) & 0x7) << 5 | (vcr) << 4 | (vbr) << 3		\
446  * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
447  * <14>    :: Charge through current support (0b == 3A, 1b == 5A)
451  * <0>     :: Charge through support (0b == no, 1b == yes)