302 	D_INFO("Attempting to send sync command %s\n",  in il_send_cmd_sync()
306 	D_INFO("Setting HCMD_ACTIVE for command %s\n",  in il_send_cmd_sync()
327 			D_INFO("Clearing HCMD_ACTIVE for command %s\n",  in il_send_cmd_sync()
1181 		D_INFO("Defer power set mode while scanning\n");  in il_power_set_mode()
1770 	D_INFO("Processing response for adding station %u\n", sta_id);  in il_process_add_sta_resp()
1776 		D_INFO("C_ADD_STA PASSED\n");  in il_process_add_sta_resp()
1796 	D_INFO("%s station id %u addr %pM\n",  in il_process_add_sta_resp()
1809 	D_INFO("%s station according to cmd buffer %pM\n",  in il_process_add_sta_resp()
1840 	D_INFO("Adding sta %u (%pM) %ssynchronously\n", sta_id, sta->sta.addr,  in il_send_add_sta()
1960 		D_INFO("STA %d already in process of being added.\n", sta_id);  in il_prep_station()
2030 		D_INFO("STA %d already in process of being added.\n", sta_id);  in il_add_station_common()
2148 		D_INFO("Unable to remove station %pM, device not ready.\n",  in il_remove_station()
2166 		D_INFO("Removing %pM but non DRIVER active\n", addr);  in il_remove_station()
2171 		D_INFO("Removing %pM but non UCODE active\n", addr);  in il_remove_station()
2210 	D_INFO("Clearing ucode stations in driver\n");  in il_clear_ucode_stations()
2215 			D_INFO("Clearing ucode active for station %d\n", i);  in il_clear_ucode_stations()
2223 		D_INFO("No active stations found to be cleared\n");  in il_clear_ucode_stations()
2247 		D_INFO("Not ready yet, not restoring any stations.\n");  in il_restore_stations()
2299 		D_INFO("Restoring all known stations"  in il_restore_stations()
2302 		D_INFO("Restoring all known stations" " .... complete.\n");  in il_restore_stations()
2378 	D_INFO("Channel %u is not an HT channel\n", il->active.channel);  in il_is_lq_table_valid()
2381 			D_INFO("idx %d of LQ expects HT channel\n", i);  in il_is_lq_table_valid()
2434 		D_INFO("init LQ command complete,"  in il_send_lq_cmd()
2571 			D_INFO("Rx queue requesting wakeup," " GP1 = 0x%x\n",  in il_rx_queue_update_write_ptr()
2726 			D_INFO("Tx queue %d requesting wakeup," " GP1 = 0x%x\n",  in il_txq_update_write_ptr()
3330 		D_INFO("Clearing HCMD_ACTIVE for command %s\n",  in il_tx_cmd_complete()
3441 		D_INFO("Geography modes already initialized.\n");  in il_init_geos()
3514 		D_INFO("Channel %d Freq=%d[%sGHz] %s flag=0x%X\n", ch->channel,  in il_init_geos()
3785 		D_INFO("need full RXON - " #cond "\n");	\  in il_full_rxon_required()
3791 		D_INFO("need full RXON - "	\  in il_full_rxon_required()
3973 	D_INFO("Staging channel set to %d [%d]\n", channel, band);  in il_set_rxon_channel()
4204 	D_INFO("stop master\n");  in _il_apm_stop_master()
4214 	D_INFO("Stop card, put in low power state\n");  in _il_apm_stop()
4254 	D_INFO("Init card's basic functions\n");  in il_apm_init()
4327 		D_INFO("Failed to init the card\n");  in il_apm_init()
4393 		D_INFO("Deferring tx power set\n");  in il_set_tx_power()
4426 	D_INFO("BT coex %s\n",  in il_send_bt_config()
4678 			D_INFO("force reset rejected\n");  in il_force_reset()
4696 		D_INFO("Cancel firmware reload based on "  in il_force_reset()
5165 		D_INFO("Not re-sending same RXON configuration.\n");  in il_mac_config()