Lines Matching +full:0 +full:x21
3 * FarSync X21 driver for Linux
104 unsigned char internalClock; /* 1 => internal clock, 0 => external */
108 unsigned short clockStatus; /* lsb: 0=> present, 1=> absent */
109 unsigned short cableStatus; /* lsb: 0=> present, 1=> absent */
112 unsigned char transparentMode; /* Not used always 0 */
121 unsigned char lineBuildOut; /* 0, -7.5, -15, -22 */
140 #define FSTVAL_NONE 0x00000000 /* Nothing valid (firmware not running).
145 #define FSTVAL_OMODEM 0x0000001F /* First 5 bits correspond to the
149 #define FSTVAL_SPEED 0x00000020 /* internalClock, lineSpeed, clockStatus
151 #define FSTVAL_CABLE 0x00000040 /* lineInterface, cableStatus */
152 #define FSTVAL_IMODEM 0x00000080 /* v24IpSts */
153 #define FSTVAL_CARD 0x00000100 /* nports, type, state, index,
156 #define FSTVAL_PROTO 0x00000200 /* proto */
157 #define FSTVAL_MODE 0x00000400 /* cardMode */
158 #define FSTVAL_PHASE 0x00000800 /* Clock phase */
159 #define FSTVAL_TE1 0x00001000 /* T1E1 Configuration */
160 #define FSTVAL_DEBUG 0x80000000 /* debug */
161 #define FSTVAL_ALL 0x00001FFF /* Note: does not include DEBUG flag */
164 #define FST_TYPE_NONE 0 /* Probably should never happen */
165 #define FST_TYPE_T2P 1 /* T2P X21 2 port card */
166 #define FST_TYPE_T4P 2 /* T4P X21 4 port card */
167 #define FST_TYPE_T1U 3 /* T1U X21 1 port card */
168 #define FST_TYPE_T2U 4 /* T2U X21 2 port card */
169 #define FST_TYPE_T4U 5 /* T4U X21 4 port card */
170 #define FST_TYPE_TE1 6 /* T1E1 X21 1 port card */
173 #define FST_FAMILY_TXP 0 /* T2P or T4P */
177 #define FST_UNINIT 0 /* Raw uninitialised state following
190 #define X21 2 macro
203 #define EXTCLK 0
206 #define IPSTS_CTS 0x00000001 /* Clear To Send (Indicate for X.21) */
208 #define IPSTS_DSR 0x00000002 /* Data Set Ready (T2P Port A) */
209 #define IPSTS_DCD 0x00000004 /* Data Carrier Detect */
210 #define IPSTS_RI 0x00000008 /* Ring Indicator (T2P Port A) */
211 #define IPSTS_TMI 0x00000010 /* Test Mode Indicator (Not Supported)*/
214 #define OPSTS_RTS 0x00000001 /* Request To Send (Control for X.21) */
216 #define OPSTS_DTR 0x00000002 /* Data Terminal Ready */
217 #define OPSTS_DSRS 0x00000004 /* Data Signalling Rate Select (Not
219 #define OPSTS_SS 0x00000008 /* Select Standby (Not Supported) */
220 #define OPSTS_LL 0x00000010 /* Maintenance Test (Not Supported) */
223 #define CARD_MODE_IDENTIFY 0x0001
232 #define CLOCKING_SLAVE 0
238 #define FRAMING_E1 0
245 #define STRUCTURE_UNFRAMED 0
257 #define INTERFACE_RJ48C 0
264 #define CODING_HDB3 0
276 #define LBO_0dB 0
284 #define RANGE_0_133_FT 0
297 #define EQUALIZER_SHORT 0
303 #define LOOP_NONE 0
312 #define BUFFER_2_FRAME 0
320 * should define FST_DEBUG=0 in order to exclude the code.
325 #define FST_DEBUG 0x0000
329 * listed below. Note: Bit 0 is used
333 #define DBG_INIT 0x0002 /* Card detection and initialisation */
334 #define DBG_OPEN 0x0004 /* Open and close sequences */
335 #define DBG_PCI 0x0008 /* PCI config operations */
336 #define DBG_IOCTL 0x0010 /* Ioctls and other config */
337 #define DBG_INTR 0x0020 /* Interrupt routines (be careful) */
338 #define DBG_TX 0x0040 /* Packet transmission */
339 #define DBG_RX 0x0080 /* Packet reception */
340 #define DBG_CMD 0x0100 /* Port command issuing */
342 #define DBG_ASS 0xFFFF /* Assert like statements. Code that