Kconfig - OpenGrok cross reference for /linux-6.12.1/drivers/leds/Kconfig

1 # SPDX-License-Identifier: GPL-2.0-only
56 	  See Documentation/ABI/testing/sysfs-class-led for details.
65 	  This option enables support for on-chip LED drivers found on Marvell
72 	  This option enables support for the AN30259A 3-channel
76 	  will be called leds-an30259a.
86 	  If you're looking for APU2/3, use the pcengines-apu2 driver.
90 	  module will be called leds-apu.
112 	    - AW20036 (3x12) 36 LEDs
113 	    - AW20054 (6x9)  54 LEDs
114 	    - AW20072 (6x12) 72 LEDs
115 	    - AW20108 (9x12) 108 LEDs
118 	  will be called leds-aw200xx.
125 	  This option enables support for the AW2013 3-channel
129 	  will be called leds-aw2013.
141 	tristate "LED Support for Broadcom BCM6358"
146 	  This option enables support for LEDs connected to the BCM6358
158 	  will be called leds-cht-wcove.
180 	  will be called leds-cr0014114.
195 	  will be called leds-cros_ec.
208 	  will be called leds-el15203000.
256 	  ambient-light-sensor interface. The chip supports
257 	  hardware-accelerated blinking with maximum on and off periods of 9.8
266 	  The LM3642 is a 4MHz fixed-frequency synchronous boost
267 	  converter plus 1.5A constant current driver for a high-current
284 	  Zaurus models SL-5500 and SL-5600.
299 	  This option enables support for on-chip LED drivers found on
338 	  It uses a one-wire interface to control up to 1024 LEDs.
375 	bool "Enable GPIO support for PCA9532"
379 	  Allow unused pins on PCA9532 to be used as gpio.
381 	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
385 	tristate "LED Support for GPIO connected LEDs"
389 	  This option enables support for the LEDs connected to GPIO
391 	  and they must be connected to the GPIO lines.  The LEDs must be
405 	  module will be called leds-lp3944.
418 	  module will be called leds-lp3952.
429 	  module will be called leds-lp50xx.
523 	  The driver supports two kinds of interface: using ledtrig-timer
543 	  module will be called leds-clevo-mail.
555 	bool "Enable GPIO support for PCA955X"
559 	  Allow unused pins on PCA955X to be used as gpio.
561 	  To use a pin as gpio the pin type should be set to
604 	  This option enables support for on-chip LED drivers found
612 	  This option enables support for on-chip LED drivers found
613 	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
649 	  be called leds-bd2606mvv.
676 	  LT3593 controller. This controller uses a special one-wire pulse
684 	  This option enables support for on-chip LED drivers found
688 	  be called leds-adp5520.
699 	  be called leds-max5970.
706 	  This option enables support for on-chip LED drivers found
710 	tristate "LED support for Network Space v2 GPIO LEDs"
715 	  This option enables support for the dual-GPIO LEDs found on the
721 		n090401 (Seagate NAS 4-Bay)
732 	  controlled through a GPIO extension bus.
740 	  Driver support brightness control and hardware-assisted blinking.
760 	  This option enables support for on-chip LED drivers on
785 	  will be called leds-menf21bmc.
797 	  called leds-is31fl319x.
803 	  Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
804 	  LED controllers. They are I2C devices with multiple constant-current
805 	  channels, each with independent 256-level PWM control.
816 	  called leds-sc27xx-bltc.
845 	  will be called leds-powernv.
880 	  module, choose 'M' here: the module will be called leds-mlxreg.
899 	  will be called leds-nic78bx.
953 	  will be called leds-ip30.