Lines Matching +full:serial +full:- +full:number

1 # SPDX-License-Identifier: GPL-2.0
4 # see Documentation/kbuild/kconfig-language.rst.
25 	  This is the base system for character-based LCD displays.
67 	  Say Y here if you have an HD44780 or KS-0074 LCD connected to your
68 	  parallel port. This driver also features 4 and 6-key keypads. The LCD
77 	int "Default parallel port number (0=LPT1)"
88 	int "Default panel profile (0-5, 0=custom)"
99 	    2 = 2x16 serial LCD (KS-0074), new keypad
119 	    2 : new 6 keys keypad, as used on the server at www.ant-computing.com
140 	     3 : 2x16 serial LCD (KS-0074 based)
150 	int "Number of lines on the LCD (1-2)"
154 	  This is the number of visible character lines on the LCD in custom profile.
159 	int "Number of characters per line on the LCD (1-40)"
163 	  This is the number of characters per line on the LCD in custom profile.
168 	int "Internal LCD line width (1-40, 40 by default)"
174 	  to the terminal. This results in some non-visible but addressable characters,
175 	  and is the case for most parallel LCDs. Other LCDs, and some serial ones,
184 	int "Hardware LCD line width (1-64, 64 by default)"
214 	int "LCD communication mode (0=parallel 8 bits, 1=serial)"
218 	  This driver now supports any serial or parallel LCD wired to a parallel
220 	  be driving a serial LCD or a parallel one. Serial LCDs only use 2 wires
223 	  parallel LCD, and 1 for a serial LCD.
227 	int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) "
228 	range -17 17
231 	  This describes the number of the parallel port pin to which the LCD 'E'
236 	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
242 	int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) "
243 	range -17 17
246 	  This describes the number of the parallel port pin to which the LCD 'RS'
251 	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
257 	int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) "
258 	range -17 17
261 	  This describes the number of the parallel port pin to which the LCD 'RW'
266 	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
272 	int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) "
273 	range -17 17
276 	  This describes the number of the parallel port pin to which the serial
281 	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
287 	int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) "
288 	range -17 17
291 	  This describes the number of the parallel port pin to which the serial
296 	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
302 	int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) "
303 	range -17 17
306 	  This describes the number of the parallel port pin to which the LCD 'BL' signal
311 	    -1..-17 : connected to the same pin through an inverter (eg: transistor).
340 	  printf()-formatted message is valid with newline and escape codes.
381 	  and built-in as well (Y).
432 	  If you have a Crystalfontz 128x64 2-color LCD, cfag12864b Series,
436 	  check Documentation/admin-guide/auxdisplay/cfag12864b.rst
476 	  This is the core support for single-line character displays, to be
504 	tristate "Maxim MAX6958/6959 7-segment LED controller"
510 	  (I2C 7-segment LED display controller):
511 	  - MAX6958
512 	  - MAX6959 (input support)
518 	tristate "Generic 7-segment LED display"
522 	  This driver supports a generic 7-segment LED display made up
526 	  will be called seg-led-gpio.
529 # Character LCD with non-conforming interface section