1 // SPDX-License-Identifier: GPL-2.0-or-later
5  * Copyright (C) 2008-2011 Manuel Lauss
9 #include <linux/dma-mapping.h>
25 #include <asm/mach-au1x00/au1000.h>
26 #include <asm/mach-au1x00/au1100_mmc.h>
27 #include <asm/mach-au1x00/au1xxx_dbdma.h>
28 #include <asm/mach-au1x00/au1xxx_psc.h>
29 #include <asm/mach-au1x00/au1200fb.h>
30 #include <asm/mach-au1x00/au1550_spi.h>
31 #include <asm/mach-db1x00/bcsr.h>
121 		return -ENODEV;  in db1200_board_setup()
130 		return -ENODEV;  in db1200_board_setup()
133 	printk(KERN_INFO "Alchemy/AMD/RMI %s Board, CPLD Rev %d"  in db1200_board_setup()
134 		"  Board-ID %d	Daughtercard ID %d\n", get_system_type(),  in db1200_board_setup()
180 	{ I2C_BOARD_INFO("24c04", 0x52),  }, /* AT24C04-10 I2C eeprom */
181 	{ I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
190 	unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W;  in au1200_nand_cmd_ctrl()
202 	this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr;  in au1200_nand_cmd_ctrl()
204 		__raw_writeb(cmd, this->legacy.IO_ADDR_W);  in au1200_nand_cmd_ctrl()
253 	.id		= -1,
285 	.id		= -1,
300 		.end	= DB1200_IDE_PHYS_ADDR + IDE_ALT_START - 1,
305 		.end	= DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
330 /* SD carddetects:  they're supposed to be edge-triggered, but ack
331  * doesn't seem to work (CPLD Rev 2).  Instead, the screaming one
417 /* -- */
543 	.name		= "au1xxx-mmc",
578 	.name		= "au1xxx-mmc",
622 		.end	= AU1200_LCD_PHYS_ADDR + 0x800 - 1,
633 	.name		= "au1200-lcd",
696 	.name		= "au1550-spi",
744 	.name		= "ac97-codec",
749 	.name		= "au1xpsc-pcm",
781 		printk(KERN_ERR "PB1200 must be at CPLD rev 4. Please have\n");  in pb1200_res_fixup()
784 		printk(KERN_ERR "on anything older than CPLD rev 4.!\n");  in pb1200_res_fixup()
793 	db1200_ide_res[0].end	= PB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1;  in pb1200_res_fixup()
810 			return -ENODEV;  in db1200_dev_setup()
813 	/* GPIO7 is low-level triggered CPLD cascade */  in db1200_dev_setup()
828 		if ((pfc < 1) || (abs(50000000 - pfc) > 2500000))  in db1200_dev_setup()
857 	/* NOTE: GPIO215 controls OTG VBUS supply.  In SPI mode however  in db1200_dev_setup()
860 	 * As a result, in SPI mode, OTG simply won't work (PSC0 uses  in db1200_dev_setup()
865 	/* switch off OTG VBUS supply */  in db1200_dev_setup()
866 	gpio_request(215, "otg-vbus");  in db1200_dev_setup()
879 		printk(KERN_INFO "   OTG port VBUS supply available!\n");  in db1200_dev_setup()
887 		printk(KERN_INFO "   OTG port VBUS supply disabled\n");  in db1200_dev_setup()
898 		db1200_sound_dev.name = "db1200-i2s";  in db1200_dev_setup()
903 		db1200_sound_dev.name = "db1200-ac97";  in db1200_dev_setup()
914 		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,  in db1200_dev_setup()
916 		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,  in db1200_dev_setup()
918 		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,  in db1200_dev_setup()
924 		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,  in db1200_dev_setup()
926 		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,  in db1200_dev_setup()
928 		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,  in db1200_dev_setup()