Lines Matching +full:fails +full:- +full:without +full:- +full:test +full:- +full:cd
1 // SPDX-License-Identifier: GPL-2.0-only OR MIT
5 * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
6 * Copyright (C) 2022-2024 Robert Nelson, BeagleBoard.org Foundation
9 /dts-v1/;
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/gpio/gpio.h>
13 #include <dt-bindings/input/input.h>
14 #include "k3-am625.dtsi"
17 compatible = "beagle,am625-beagleplay", "ti,am625";
44 stdout-path = "serial2:115200n8";
48 bootph-pre-ram;
54 reserved-memory {
55 #address-cells = <2>;
56 #size-cells = <2>;
62 record-size = <0x8000>;
63 console-size = <0x8000>;
64 ftrace-size = <0x00>;
65 pmsg-size = <0x8000>;
70 no-map;
75 no-map;
78 wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
79 compatible = "shared-dma-pool";
81 no-map;
85 sdio_pwrseq: sdio-pwrseq {
86 compatible = "mmc-pwrseq-simple";
87 pinctrl-names = "default";
88 pinctrl-0 = <&wifi_en_pins_default>;
89 /* Internal power on time(Figure 8-3) * 2 */
90 post-power-on-delay-ms = <10>;
91 /* Re-enable time(Figure 8-2) + 20uS */
92 power-off-delay-us = <80>;
93 reset-gpios = <&main_gpio0 38 GPIO_ACTIVE_LOW>;
96 vsys_5v0: regulator-1 {
97 bootph-all;
98 compatible = "regulator-fixed";
99 regulator-name = "vsys_5v0";
100 regulator-min-microvolt = <5000000>;
101 regulator-max-microvolt = <5000000>;
102 regulator-always-on;
103 regulator-boot-on;
106 vdd_3v3: regulator-2 {
107 /* output of TLV62595DMQR-U12 */
108 bootph-all;
109 compatible = "regulator-fixed";
110 regulator-name = "vdd_3v3";
111 regulator-min-microvolt = <3300000>;
112 regulator-max-microvolt = <3300000>;
113 vin-supply = <&vsys_5v0>;
114 regulator-always-on;
115 regulator-boot-on;
118 vdd_3v3_sd: regulator-4 {
119 /* output of TPS22918DBVR-U21 */
120 bootph-all;
121 pinctrl-names = "default";
122 pinctrl-0 = <&vdd_3v3_sd_pins_default>;
124 compatible = "regulator-fixed";
125 regulator-name = "vdd_3v3_sd";
126 regulator-min-microvolt = <3300000>;
127 regulator-max-microvolt = <3300000>;
128 enable-active-high;
129 regulator-always-on;
130 vin-supply = <&vdd_3v3>;
134 vdd_sd_dv: regulator-5 {
135 bootph-all;
136 compatible = "regulator-gpio";
137 regulator-name = "sd_hs200_switch";
138 pinctrl-names = "default";
139 pinctrl-0 = <&vdd_sd_dv_pins_default>;
140 regulator-min-microvolt = <1800000>;
141 regulator-max-microvolt = <3300000>;
142 regulator-boot-on;
143 vin-supply = <&ldo1_reg>;
150 bootph-all;
151 compatible = "gpio-leds";
153 led-0 {
154 bootph-all;
156 linux,default-trigger = "heartbeat";
158 default-state = "off";
161 led-1 {
162 bootph-all;
164 linux,default-trigger = "disk-activity";
166 default-state = "keep";
169 led-2 {
170 bootph-all;
175 led-3 {
176 bootph-all;
181 led-4 {
182 bootph-all;
188 gpio_keys: gpio-keys {
189 compatible = "gpio-keys";
191 pinctrl-names = "default";
192 pinctrl-0 = <&usr_button_pins_default>;
194 usr: button-usr {
202 hdmi0: connector-hdmi {
203 compatible = "hdmi-connector";
208 remote-endpoint = <&it66121_out>;
214 compatible = "simple-audio-card";
215 simple-audio-card,name = "it66121 HDMI";
216 simple-audio-card,format = "i2s";
217 simple-audio-card,bitclock-master = <&hdmi_dailink_master>;
218 simple-audio-card,frame-master = <&hdmi_dailink_master>;
220 hdmi_dailink_master: simple-audio-card,cpu {
221 sound-dai = <&mcasp1>;
222 system-clock-direction-out;
225 simple-audio-card,codec {
226 sound-dai = <&it66121>;
233 gpio0_pins_default: gpio0-default-pins {
234 bootph-all;
235 pinctrl-single,pins = <
253 vdd_sd_dv_pins_default: vdd-sd-default-pins {
254 bootph-all;
255 pinctrl-single,pins = <
260 usr_button_pins_default: usr-button-default-pins {
261 pinctrl-single,pins = <
266 grove_pins_default: grove-default-pins {
267 pinctrl-single,pins = <
273 local_i2c_pins_default: local-i2c-default-pins {
274 bootph-all;
275 pinctrl-single,pins = <
281 i2c2_1v8_pins_default: i2c2-default-pins {
282 pinctrl-single,pins = <
288 mdio0_pins_default: mdio0-default-pins {
289 pinctrl-single,pins = <
297 rgmii1_pins_default: rgmii1-default-pins {
298 pinctrl-single,pins = <
314 emmc_pins_default: emmc-default-pins {
315 bootph-all;
316 pinctrl-single,pins = <
330 vdd_3v3_sd_pins_default: vdd-3v3-sd-default-pins {
331 bootph-all;
332 pinctrl-single,pins = <
337 sd_pins_default: sd-default-pins {
338 bootph-all;
339 pinctrl-single,pins = <
350 wifi_pins_default: wifi-default-pins {
351 pinctrl-single,pins = <
363 wifi_en_pins_default: wifi-en-default-pins {
364 pinctrl-single,pins = <
369 wifi_wlirq_pins_default: wifi-wlirq-default-pins {
370 pinctrl-single,pins = <
375 spe_pins_default: spe-default-pins {
376 pinctrl-single,pins = <
390 mikrobus_i2c_pins_default: mikrobus-i2c-default-pins {
391 pinctrl-single,pins = <
397 mikrobus_uart_pins_default: mikrobus-uart-default-pins {
398 pinctrl-single,pins = <
404 mikrobus_spi_pins_default: mikrobus-spi-default-pins {
405 pinctrl-single,pins = <
413 mikrobus_gpio_pins_default: mikrobus-gpio-default-pins {
414 bootph-all;
415 pinctrl-single,pins = <
422 main_uart0_pins_default: main-uart0-default-pins {
423 bootph-all;
424 pinctrl-single,pins = <
430 wifi_debug_uart_pins_default: wifi-debug-uart-default-pins {
431 pinctrl-single,pins = <
437 usb1_pins_default: usb1-default-pins {
438 pinctrl-single,pins = <
443 pmic_irq_pins_default: pmic-irq-default-pins {
444 pinctrl-single,pins = <
449 hdmi_gpio_pins_default: hdmi-gpio-default-pins {
450 pinctrl-single,pins = <
456 mcasp_hdmi_pins_default: mcasp-hdmi-default-pins {
457 pinctrl-single,pins = <
467 dss0_pins_default: dss0-default-pins {
468 pinctrl-single,pins = <
502 i2c_qwiic_pins_default: i2c-qwiic-default-pins {
503 pinctrl-single,pins = <
509 gbe_pmx_obsclk: gbe-pmx-obsclk-default-pins {
510 pinctrl-single,pins = <
515 i2c_csi_pins_default: i2c-csi-default-pins {
516 pinctrl-single,pins = <
522 wifi_32k_clk: mcu-clk-out-default-pins {
523 pinctrl-single,pins = <
531 opp-1400000000 {
532 opp-hz = /bits/ 64 <1400000000>;
533 opp-supported-hw = <0x01 0x0004>;
538 pinctrl-names = "default";
539 pinctrl-0 = <&i2c_csi_pins_default>;
540 clock-frequency = <400000>;
545 pinctrl-names = "default";
546 pinctrl-0 = <&i2c_qwiic_pins_default>;
547 clock-frequency = <100000>;
552 bootph-all;
553 ti,vbus-divider;
558 bootph-all;
563 ti,vbus-divider;
569 pinctrl-names = "default";
570 pinctrl-0 = <&usb1_pins_default>;
574 pinctrl-names = "default";
575 pinctrl-0 = <&rgmii1_pins_default>, <&spe_pins_default>,
577 assigned-clocks = <&k3_clks 157 70>, <&k3_clks 157 20>;
578 assigned-clock-parents = <&k3_clks 157 72>, <&k3_clks 157 22>;
582 phy-mode = "rgmii-rxid";
583 phy-handle = <&cpsw3g_phy0>;
587 phy-mode = "rmii";
588 phy-handle = <&cpsw3g_phy1>;
593 pinctrl-names = "default";
594 pinctrl-0 = <&mdio0_pins_default>;
596 cpsw3g_phy0: ethernet-phy@0 {
598 reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
599 reset-assert-us = <10000>;
600 reset-deassert-us = <50000>;
603 cpsw3g_phy1: ethernet-phy@1 {
605 reset-gpios = <&main_gpio1 5 GPIO_ACTIVE_LOW>;
606 reset-assert-us = <25>;
607 reset-deassert-us = <60000>; /* T2 */
612 bootph-all;
613 pinctrl-names = "default";
614 pinctrl-0 = <&gpio0_pins_default>;
615 gpio-line-names = "BL_EN_3V3", "SPE_PO_EN", "RTC_INT", /* 0-2 */
616 "USR0", "USR1", "USR2", "USR3", "", "", "USR4", /* 3-9 */
618 "CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2", /* 11-12 */
619 "CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "", /* 13-17 */
620 "USR_BUTTON", "", "", "", "", "", "", "", "", /* 18-26 */
621 "", "", "", "", "", "", "", "", "", "HDMI_INT", /* 27-36 */
622 "", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
623 "", "", "", "", "", "", "", "", "", "", "", "", /* 43-54 */
624 "", "", "", "", "", "", "", "", "", "", "", "", /* 55-66 */
625 "", "", "", "", "", "", "", "", "", "", "", "", /* 67-78 */
626 "", "", "", "", "", "", /* 79-84 */
627 "BITBANG_MDIO_DATA", "BITBANG_MDIO_CLK", /* 85-86 */
628 "", "", "", "", ""; /* 87-91 */
632 bootph-all;
633 pinctrl-names = "default";
634 pinctrl-0 = <&mikrobus_gpio_pins_default>;
635 gpio-line-names = "", "", "", "", "", /* 0-4 */
636 "SPE_RSTN", "SPE_INTN", "MIKROBUS_GPIO1_7", /* 5-7 */
637 "MIKROBUS_GPIO1_8", "MIKROBUS_GPIO1_9", /* 8-9 */
638 "MIKROBUS_GPIO1_10", "MIKROBUS_GPIO1_11", /* 10-11 */
639 "MIKROBUS_GPIO1_12", "MIKROBUS_W1_GPIO0", /* 12-13 */
641 "", "", "", "", "VDD_3V3_SD", "", "", /* 15-21 */
642 "MIKROBUS_GPIO1_22", "MIKROBUS_GPIO1_23", /* 22-23 */
643 "MIKROBUS_GPIO1_24", "MIKROBUS_GPIO1_25", /* 24-25 */
644 "", "", "", "", "", "", "", "", "", "", "", "", /* 26-37 */
645 "", "", "", "", "", "", "", "", "", "", /* 38-47 */
646 "SD_CD", "SD_VOLT_SEL", "", ""; /* 48-51 */
650 bootph-all;
651 pinctrl-names = "default";
652 pinctrl-0 = <&local_i2c_pins_default>;
653 clock-frequency = <400000>;
664 interrupt-parent = <&main_gpio0>;
669 bootph-all;
672 buck1-supply = <&vsys_5v0>;
673 buck2-supply = <&vsys_5v0>;
674 buck3-supply = <&vsys_5v0>;
675 ldo1-supply = <&vdd_3v3>;
676 ldo2-supply = <&buck2_reg>;
677 ldo3-supply = <&vdd_3v3>;
678 ldo4-supply = <&vdd_3v3>;
680 pinctrl-names = "default";
681 pinctrl-0 = <&pmic_irq_pins_default>;
682 interrupt-parent = <&gic500>;
684 interrupt-controller;
685 #interrupt-cells = <1>;
687 system-power-controller;
688 ti,power-button;
692 regulator-name = "VDD_CORE";
693 regulator-min-microvolt = <850000>;
694 regulator-max-microvolt = <850000>;
695 regulator-boot-on;
696 regulator-always-on;
700 regulator-name = "VDD_1V8";
701 regulator-min-microvolt = <1800000>;
702 regulator-max-microvolt = <1800000>;
703 regulator-boot-on;
704 regulator-always-on;
708 regulator-name = "VDD_1V2";
709 regulator-min-microvolt = <1200000>;
710 regulator-max-microvolt = <1200000>;
711 regulator-boot-on;
712 regulator-always-on;
721 regulator-name = "VDD_SD_3V3";
722 regulator-min-microvolt = <3300000>;
723 regulator-max-microvolt = <3300000>;
724 regulator-allow-bypass;
725 regulator-boot-on;
726 regulator-always-on;
730 regulator-name = "VDDA_0V85";
731 regulator-min-microvolt = <850000>;
732 regulator-max-microvolt = <850000>;
733 regulator-boot-on;
734 regulator-always-on;
738 regulator-name = "VDDA_1V8";
739 regulator-min-microvolt = <1800000>;
740 regulator-max-microvolt = <1800000>;
741 regulator-boot-on;
742 regulator-always-on;
746 regulator-name = "VDD_2V5";
747 regulator-min-microvolt = <2500000>;
748 regulator-max-microvolt = <2500000>;
749 regulator-boot-on;
750 regulator-always-on;
757 pinctrl-names = "default";
758 pinctrl-0 = <&grove_pins_default>;
759 clock-frequency = <100000>;
764 pinctrl-names = "default";
765 pinctrl-0 = <&i2c2_1v8_pins_default>;
766 clock-frequency = <100000>;
769 it66121: bridge-hdmi@4c {
772 pinctrl-names = "default";
773 pinctrl-0 = <&hdmi_gpio_pins_default>;
774 vcn33-supply = <&vdd_3v3>;
775 vcn18-supply = <&buck2_reg>;
776 vrf12-supply = <&buck3_reg>;
777 reset-gpios = <&main_gpio0 21 GPIO_ACTIVE_LOW>;
778 interrupt-parent = <&main_gpio0>;
780 #sound-dai-cells = <0>;
783 #address-cells = <1>;
784 #size-cells = <0>;
790 bus-width = <24>;
791 remote-endpoint = <&dpi1_out>;
799 remote-endpoint = <&hdmi_connector_in>;
807 pinctrl-names = "default";
808 pinctrl-0 = <&mikrobus_i2c_pins_default>;
809 clock-frequency = <400000>;
814 pinctrl-names = "default";
815 pinctrl-0 = <&mikrobus_spi_pins_default>;
820 bootph-all;
821 pinctrl-names = "default";
822 pinctrl-0 = <&emmc_pins_default>;
823 disable-wp;
829 bootph-all;
830 pinctrl-names = "default";
831 pinctrl-0 = <&sd_pins_default>;
833 vmmc-supply = <&vdd_3v3_sd>;
834 vqmmc-supply = <&vdd_sd_dv>;
835 disable-wp;
836 cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
837 cd-debounce-delay-ms = <100>;
838 ti,fails-without-test-cd;
843 pinctrl-names = "default";
844 pinctrl-0 = <&wifi_pins_default>, <&wifi_32k_clk>;
845 non-removable;
846 ti,fails-without-test-cd;
847 cap-power-off-card;
848 keep-power-in-suspend;
849 mmc-pwrseq = <&sdio_pwrseq>;
850 assigned-clocks = <&k3_clks 157 158>;
851 assigned-clock-parents = <&k3_clks 157 160>;
852 #address-cells = <1>;
853 #size-cells = <0>;
859 pinctrl-names = "default";
860 pinctrl-0 = <&wifi_wlirq_pins_default>;
861 interrupt-parent = <&main_gpio0>;
867 bootph-all;
868 pinctrl-names = "default";
869 pinctrl-0 = <&main_uart0_pins_default>;
879 pinctrl-names = "default";
880 pinctrl-0 = <&mikrobus_uart_pins_default>;
885 pinctrl-names = "default";
886 pinctrl-0 = <&wifi_debug_uart_pins_default>;
891 bootloader-backdoor-gpios = <&main_gpio0 13 GPIO_ACTIVE_HIGH>;
892 reset-gpios = <&main_gpio0 14 GPIO_ACTIVE_HIGH>;
893 vdds-supply = <&vdd_3v3>;
899 pinctrl-names = "default";
900 pinctrl-0 = <&dss0_pins_default>;
909 remote-endpoint = <&it66121_in>;
916 #sound-dai-cells = <0>;
917 pinctrl-names = "default";
918 pinctrl-0 = <&mcasp_hdmi_pins_default>;
919 auxclk-fs-ratio = <2177>;
920 op-mode = <0>; /* MCASP_IIS_MODE */
921 tdm-slots = <2>;
922 serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */