Lines Matching +full:va +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/gpio-keys.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
14 #include "x1e80100-pmics.dtsi"
18 compatible = "qcom,x1e80100-crd", "qcom,x1e80100";
24 wcd938x: audio-codec {
25 compatible = "qcom,wcd9385-codec";
27 pinctrl-names = "default";
28 pinctrl-0 = <&wcd_default>;
30 qcom,micbias1-microvolt = <1800000>;
31 qcom,micbias2-microvolt = <1800000>;
32 qcom,micbias3-microvolt = <1800000>;
33 qcom,micbias4-microvolt = <1800000>;
34 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
35 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
36 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
37 qcom,rx-device = <&wcd_rx>;
38 qcom,tx-device = <&wcd_tx>;
40 reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
42 vdd-buck-supply = <&vreg_l15b_1p8>;
43 vdd-rxtx-supply = <&vreg_l15b_1p8>;
44 vdd-io-supply = <&vreg_l15b_1p8>;
45 vdd-mic-bias-supply = <&vreg_bob1>;
47 #sound-dai-cells = <1>;
51 stdout-path = "serial0:115200n8";
54 gpio-keys {
55 compatible = "gpio-keys";
57 pinctrl-0 = <&hall_int_n_default>;
58 pinctrl-names = "default";
60 switch-lid {
62 linux,input-type = <EV_SW>;
64 wakeup-source;
65 wakeup-event-action = <EV_ACT_DEASSERTED>;
69 pmic-glink {
70 compatible = "qcom,x1e80100-pmic-glink",
71 "qcom,sm8550-pmic-glink",
72 "qcom,pmic-glink";
73 #address-cells = <1>;
74 #size-cells = <0>;
75 orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
79 /* Left-side rear port */
81 compatible = "usb-c-connector";
83 power-role = "dual";
84 data-role = "dual";
87 #address-cells = <1>;
88 #size-cells = <0>;
94 remote-endpoint = <&usb_1_ss0_dwc3_hs>;
102 remote-endpoint = <&usb_1_ss0_qmpphy_out>;
108 /* Left-side front port */
110 compatible = "usb-c-connector";
112 power-role = "dual";
113 data-role = "dual";
116 #address-cells = <1>;
117 #size-cells = <0>;
123 remote-endpoint = <&usb_1_ss1_dwc3_hs>;
131 remote-endpoint = <&usb_1_ss1_qmpphy_out>;
137 /* Right-side port */
139 compatible = "usb-c-connector";
141 power-role = "dual";
142 data-role = "dual";
145 #address-cells = <1>;
146 #size-cells = <0>;
152 remote-endpoint = <&usb_1_ss2_dwc3_hs>;
160 remote-endpoint = <&usb_1_ss2_qmpphy_out>;
167 reserved-memory {
169 compatible = "shared-dma-pool";
172 linux,cma-default;
177 compatible = "qcom,x1e80100-sndcard";
178 model = "X1E80100-CRD";
179 audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
186 "VA DMIC0", "MIC BIAS3",
187 "VA DMIC1", "MIC BIAS3",
188 "VA DMIC2", "MIC BIAS1",
189 "VA DMIC3", "MIC BIAS1",
190 "VA DMIC0", "VA MIC BIAS3",
191 "VA DMIC1", "VA MIC BIAS3",
192 "VA DMIC2", "VA MIC BIAS1",
193 "VA DMIC3", "VA MIC BIAS1",
196 wcd-playback-dai-link {
197 link-name = "WCD Playback";
200 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
204 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
208 sound-dai = <&q6apm>;
212 wcd-capture-dai-link {
213 link-name = "WCD Capture";
216 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
220 sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
224 sound-dai = <&q6apm>;
228 wsa-dai-link {
229 link-name = "WSA Playback";
232 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
236 sound-dai = <&left_woofer>, <&left_tweeter>,
243 sound-dai = <&q6apm>;
247 va-dai-link {
248 link-name = "VA Capture";
251 sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
255 sound-dai = <&lpass_vamacro 0>;
259 sound-dai = <&q6apm>;
264 vph_pwr: vph-pwr-regulator {
265 compatible = "regulator-fixed";
267 regulator-name = "vph_pwr";
268 regulator-min-microvolt = <3700000>;
269 regulator-max-microvolt = <3700000>;
271 regulator-always-on;
272 regulator-boot-on;
275 vreg_edp_3p3: regulator-edp-3p3 {
276 compatible = "regulator-fixed";
278 regulator-name = "VREG_EDP_3P3";
279 regulator-min-microvolt = <3300000>;
280 regulator-max-microvolt = <3300000>;
283 enable-active-high;
285 pinctrl-0 = <&edp_reg_en>;
286 pinctrl-names = "default";
288 regulator-boot-on;
291 vreg_nvme: regulator-nvme {
292 compatible = "regulator-fixed";
294 regulator-name = "VREG_NVME_3P3";
295 regulator-min-microvolt = <3300000>;
296 regulator-max-microvolt = <3300000>;
299 enable-active-high;
301 pinctrl-names = "default";
302 pinctrl-0 = <&nvme_reg_en>;
304 regulator-boot-on;
307 vreg_wwan: regulator-wwan {
308 compatible = "regulator-fixed";
310 regulator-name = "SDX_VPH_PWR";
311 regulator-min-microvolt = <3300000>;
312 regulator-max-microvolt = <3300000>;
315 enable-active-high;
317 pinctrl-0 = <&wwan_sw_en>;
318 pinctrl-names = "default";
320 regulator-boot-on;
325 regulators-0 {
326 compatible = "qcom,pm8550-rpmh-regulators";
327 qcom,pmic-id = "b";
329 vdd-bob1-supply = <&vph_pwr>;
330 vdd-bob2-supply = <&vph_pwr>;
331 vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
332 vdd-l2-l13-l14-supply = <&vreg_bob1>;
333 vdd-l5-l16-supply = <&vreg_bob1>;
334 vdd-l6-l7-supply = <&vreg_bob2>;
335 vdd-l8-l9-supply = <&vreg_bob1>;
336 vdd-l12-supply = <&vreg_s5j_1p2>;
337 vdd-l15-supply = <&vreg_s4c_1p8>;
338 vdd-l17-supply = <&vreg_bob2>;
341 regulator-name = "vreg_bob1";
342 regulator-min-microvolt = <3008000>;
343 regulator-max-microvolt = <3960000>;
344 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
348 regulator-name = "vreg_bob2";
349 regulator-min-microvolt = <2504000>;
350 regulator-max-microvolt = <3008000>;
351 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
355 regulator-name = "vreg_l1b_1p8";
356 regulator-min-microvolt = <1800000>;
357 regulator-max-microvolt = <1800000>;
358 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
362 regulator-name = "vreg_l2b_3p0";
363 regulator-min-microvolt = <3072000>;
364 regulator-max-microvolt = <3100000>;
365 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
369 regulator-name = "vreg_l4b_1p8";
370 regulator-min-microvolt = <1800000>;
371 regulator-max-microvolt = <1800000>;
372 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
376 regulator-name = "vreg_l5b_3p0";
377 regulator-min-microvolt = <3000000>;
378 regulator-max-microvolt = <3000000>;
379 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
383 regulator-name = "vreg_l6b_1p8";
384 regulator-min-microvolt = <1800000>;
385 regulator-max-microvolt = <2960000>;
386 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
390 regulator-name = "vreg_l7b_2p8";
391 regulator-min-microvolt = <2800000>;
392 regulator-max-microvolt = <2800000>;
393 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
397 regulator-name = "vreg_l8b_3p0";
398 regulator-min-microvolt = <3072000>;
399 regulator-max-microvolt = <3072000>;
400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
404 regulator-name = "vreg_l9b_2p9";
405 regulator-min-microvolt = <2960000>;
406 regulator-max-microvolt = <2960000>;
407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
411 regulator-name = "vreg_l10b_1p8";
412 regulator-min-microvolt = <1800000>;
413 regulator-max-microvolt = <1800000>;
414 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
418 regulator-name = "vreg_l12b_1p2";
419 regulator-min-microvolt = <1200000>;
420 regulator-max-microvolt = <1200000>;
421 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
425 regulator-name = "vreg_l13b_3p0";
426 regulator-min-microvolt = <3072000>;
427 regulator-max-microvolt = <3100000>;
428 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
432 regulator-name = "vreg_l14b_3p0";
433 regulator-min-microvolt = <3072000>;
434 regulator-max-microvolt = <3072000>;
435 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
439 regulator-name = "vreg_l15b_1p8";
440 regulator-min-microvolt = <1800000>;
441 regulator-max-microvolt = <1800000>;
442 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
446 regulator-name = "vreg_l16b_2p9";
447 regulator-min-microvolt = <2912000>;
448 regulator-max-microvolt = <2912000>;
449 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
453 regulator-name = "vreg_l17b_2p5";
454 regulator-min-microvolt = <2504000>;
455 regulator-max-microvolt = <2504000>;
456 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
460 regulators-1 {
461 compatible = "qcom,pm8550ve-rpmh-regulators";
462 qcom,pmic-id = "c";
464 vdd-l1-supply = <&vreg_s5j_1p2>;
465 vdd-l2-supply = <&vreg_s1f_0p7>;
466 vdd-l3-supply = <&vreg_s1f_0p7>;
467 vdd-s4-supply = <&vph_pwr>;
470 regulator-name = "vreg_s4c_1p8";
471 regulator-min-microvolt = <1856000>;
472 regulator-max-microvolt = <2000000>;
473 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
477 regulator-name = "vreg_l1c_1p2";
478 regulator-min-microvolt = <1200000>;
479 regulator-max-microvolt = <1200000>;
480 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
484 regulator-name = "vreg_l2c_0p8";
485 regulator-min-microvolt = <880000>;
486 regulator-max-microvolt = <920000>;
487 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
491 regulator-name = "vreg_l3c_0p8";
492 regulator-min-microvolt = <880000>;
493 regulator-max-microvolt = <920000>;
494 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
498 regulators-2 {
499 compatible = "qcom,pmc8380-rpmh-regulators";
500 qcom,pmic-id = "d";
502 vdd-l1-supply = <&vreg_s1f_0p7>;
503 vdd-l2-supply = <&vreg_s1f_0p7>;
504 vdd-l3-supply = <&vreg_s4c_1p8>;
505 vdd-s1-supply = <&vph_pwr>;
508 regulator-name = "vreg_l1d_0p8";
509 regulator-min-microvolt = <880000>;
510 regulator-max-microvolt = <920000>;
511 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
515 regulator-name = "vreg_l2d_0p9";
516 regulator-min-microvolt = <912000>;
517 regulator-max-microvolt = <920000>;
518 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
522 regulator-name = "vreg_l3d_1p8";
523 regulator-min-microvolt = <1800000>;
524 regulator-max-microvolt = <1800000>;
525 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
529 regulators-3 {
530 compatible = "qcom,pmc8380-rpmh-regulators";
531 qcom,pmic-id = "e";
533 vdd-l2-supply = <&vreg_s1f_0p7>;
534 vdd-l3-supply = <&vreg_s5j_1p2>;
537 regulator-name = "vreg_l2e_0p8";
538 regulator-min-microvolt = <880000>;
539 regulator-max-microvolt = <920000>;
540 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
544 regulator-name = "vreg_l3e_1p2";
545 regulator-min-microvolt = <1200000>;
546 regulator-max-microvolt = <1200000>;
547 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
551 regulators-4 {
552 compatible = "qcom,pmc8380-rpmh-regulators";
553 qcom,pmic-id = "f";
555 vdd-l1-supply = <&vreg_s5j_1p2>;
556 vdd-l2-supply = <&vreg_s5j_1p2>;
557 vdd-l3-supply = <&vreg_s5j_1p2>;
558 vdd-s1-supply = <&vph_pwr>;
561 regulator-name = "vreg_s1f_0p7";
562 regulator-min-microvolt = <700000>;
563 regulator-max-microvolt = <1100000>;
564 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
568 regulator-name = "vreg_l1f_1p0";
569 regulator-min-microvolt = <1024000>;
570 regulator-max-microvolt = <1024000>;
571 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
575 regulator-name = "vreg_l2f_1p0";
576 regulator-min-microvolt = <1024000>;
577 regulator-max-microvolt = <1024000>;
578 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
582 regulator-name = "vreg_l3f_1p0";
583 regulator-min-microvolt = <1024000>;
584 regulator-max-microvolt = <1024000>;
585 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
589 regulators-6 {
590 compatible = "qcom,pm8550ve-rpmh-regulators";
591 qcom,pmic-id = "i";
593 vdd-l1-supply = <&vreg_s4c_1p8>;
594 vdd-l2-supply = <&vreg_s5j_1p2>;
595 vdd-l3-supply = <&vreg_s1f_0p7>;
596 vdd-s1-supply = <&vph_pwr>;
597 vdd-s2-supply = <&vph_pwr>;
600 regulator-name = "vreg_s1i_0p9";
601 regulator-min-microvolt = <900000>;
602 regulator-max-microvolt = <920000>;
603 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
607 regulator-name = "vreg_s2i_1p0";
608 regulator-min-microvolt = <1000000>;
609 regulator-max-microvolt = <1100000>;
610 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
614 regulator-name = "vreg_l1i_1p8";
615 regulator-min-microvolt = <1800000>;
616 regulator-max-microvolt = <1800000>;
617 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
621 regulator-name = "vreg_l2i_1p2";
622 regulator-min-microvolt = <1200000>;
623 regulator-max-microvolt = <1200000>;
624 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
628 regulator-name = "vreg_l3i_0p8";
629 regulator-min-microvolt = <880000>;
630 regulator-max-microvolt = <920000>;
631 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
635 regulators-7 {
636 compatible = "qcom,pm8550ve-rpmh-regulators";
637 qcom,pmic-id = "j";
639 vdd-l1-supply = <&vreg_s1f_0p7>;
640 vdd-l2-supply = <&vreg_s5j_1p2>;
641 vdd-l3-supply = <&vreg_s1f_0p7>;
642 vdd-s5-supply = <&vph_pwr>;
645 regulator-name = "vreg_s5j_1p2";
646 regulator-min-microvolt = <1256000>;
647 regulator-max-microvolt = <1304000>;
648 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
652 regulator-name = "vreg_l1j_0p8";
653 regulator-min-microvolt = <880000>;
654 regulator-max-microvolt = <920000>;
655 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
659 regulator-name = "vreg_l2j_1p2";
660 regulator-min-microvolt = <1200000>;
661 regulator-max-microvolt = <1200000>;
662 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
666 regulator-name = "vreg_l3j_0p8";
667 regulator-min-microvolt = <880000>;
668 regulator-max-microvolt = <920000>;
669 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
677 zap-shader {
678 firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
683 clock-frequency = <400000>;
688 compatible = "hid-over-i2c";
691 hid-descr-addr = <0x1>;
692 interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
694 pinctrl-0 = <&tpad_default>;
695 pinctrl-names = "default";
697 wakeup-source;
701 compatible = "hid-over-i2c";
704 hid-descr-addr = <0x1>;
705 interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
707 pinctrl-0 = <&kybd_default>;
708 pinctrl-names = "default";
710 wakeup-source;
715 clock-frequency = <400000>;
720 compatible = "hid-over-i2c";
723 hid-descr-addr = <0x1>;
724 interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
726 pinctrl-0 = <&ts0_default>;
727 pinctrl-names = "default";
732 spkr_01_sd_n_active: spkr-01-sd-n-active-state {
735 drive-strength = <16>;
736 bias-disable;
737 output-low;
740 spkr_23_sd_n_active: spkr-23-sd-n-active-state {
743 drive-strength = <16>;
744 bias-disable;
745 output-low;
750 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
751 pinctrl-names = "default";
753 vdd-micb-supply = <&vreg_l1b_1p8>;
754 qcom,dmic-sample-rate = <4800000>;
762 compatible = "qcom,x1e80100-dp";
763 /delete-property/ #sound-dai-cells;
767 aux-bus {
770 enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
771 power-supply = <&vreg_edp_3p3>;
773 pinctrl-0 = <&edp_bl_en>;
774 pinctrl-names = "default";
778 remote-endpoint = <&mdss_dp3_out>;
788 data-lanes = <0 1 2 3>;
789 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
791 remote-endpoint = <&edp_panel_in>;
798 vdda-phy-supply = <&vreg_l3j_0p8>;
799 vdda-pll-supply = <&vreg_l2j_1p2>;
805 perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
806 wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
808 pinctrl-0 = <&pcie4_default>;
809 pinctrl-names = "default";
815 vdda-phy-supply = <&vreg_l3i_0p8>;
816 vdda-pll-supply = <&vreg_l3e_1p2>;
822 perst-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
823 wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
825 vddpe-3v3-supply = <&vreg_wwan>;
827 pinctrl-0 = <&pcie5_default>;
828 pinctrl-names = "default";
834 vdda-phy-supply = <&vreg_l3i_0p8>;
835 vdda-pll-supply = <&vreg_l3e_1p2>;
841 perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
842 wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
844 vddpe-3v3-supply = <&vreg_nvme>;
846 pinctrl-names = "default";
847 pinctrl-0 = <&pcie6a_default>;
853 vdda-phy-supply = <&vreg_l1d_0p8>;
854 vdda-pll-supply = <&vreg_l2j_1p2>;
860 edp_bl_en: edp-bl-en-state {
863 power-source = <1>; /* 1.8V */
864 input-disable;
865 output-enable;
882 firmware-name = "qcom/x1e80100/adsp.mbn",
889 firmware-name = "qcom/x1e80100/cdsp.mbn",
896 vdd18-supply = <&vreg_l3d_1p8>;
897 vdd3-supply = <&vreg_l2b_3p0>;
901 vdd18-supply = <&vreg_l3d_1p8>;
902 vdd3-supply = <&vreg_l14b_3p0>;
910 vdd18-supply = <&vreg_l3d_1p8>;
911 vdd3-supply = <&vreg_l8b_3p0>;
917 pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
918 pinctrl-names = "default";
924 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
925 #sound-dai-cells = <0>;
926 sound-name-prefix = "WooferLeft";
927 vdd-1p8-supply = <&vreg_l15b_1p8>;
928 vdd-io-supply = <&vreg_l12b_1p2>;
929 qcom,port-mapping = <1 2 3 7 10 13>;
936 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
937 #sound-dai-cells = <0>;
938 sound-name-prefix = "TweeterLeft";
939 vdd-1p8-supply = <&vreg_l15b_1p8>;
940 vdd-io-supply = <&vreg_l12b_1p2>;
941 qcom,port-mapping = <4 5 6 7 11 13>;
952 qcom,rx-port-mapping = <1 2 3 4 5>;
963 qcom,tx-port-mapping = <2 2 3 4>;
970 pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
971 pinctrl-names = "default";
977 reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
978 #sound-dai-cells = <0>;
979 sound-name-prefix = "WooferRight";
980 vdd-1p8-supply = <&vreg_l15b_1p8>;
981 vdd-io-supply = <&vreg_l12b_1p2>;
982 qcom,port-mapping = <1 2 3 7 10 13>;
989 reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
990 #sound-dai-cells = <0>;
991 sound-name-prefix = "TweeterRight";
992 vdd-1p8-supply = <&vreg_l15b_1p8>;
993 vdd-io-supply = <&vreg_l12b_1p2>;
994 qcom,port-mapping = <4 5 6 7 11 13>;
999 gpio-reserved-ranges = <34 2>, /* Unused */
1003 edp_reg_en: edp-reg-en-state {
1006 drive-strength = <16>;
1007 bias-disable;
1010 hall_int_n_default: hall-int-n-state {
1013 bias-disable;
1016 kybd_default: kybd-default-state {
1019 bias-disable;
1022 nvme_reg_en: nvme-reg-en-state {
1025 drive-strength = <2>;
1026 bias-disable;
1029 pcie4_default: pcie4-default-state {
1030 clkreq-n-pins {
1033 drive-strength = <2>;
1034 bias-pull-up;
1037 perst-n-pins {
1040 drive-strength = <2>;
1041 bias-disable;
1044 wake-n-pins {
1047 drive-strength = <2>;
1048 bias-pull-up;
1052 pcie5_default: pcie5-default-state {
1053 clkreq-n-pins {
1056 drive-strength = <2>;
1057 bias-pull-up;
1060 perst-n-pins {
1063 drive-strength = <2>;
1064 bias-disable;
1067 wake-n-pins {
1070 drive-strength = <2>;
1071 bias-pull-up;
1075 pcie6a_default: pcie6a-default-state {
1076 clkreq-n-pins {
1079 drive-strength = <2>;
1080 bias-pull-up;
1083 perst-n-pins {
1086 drive-strength = <2>;
1087 bias-disable;
1090 wake-n-pins {
1093 drive-strength = <2>;
1094 bias-pull-up;
1098 tpad_default: tpad-default-state {
1101 bias-disable;
1104 ts0_default: ts0-default-state {
1105 int-n-pins {
1108 bias-disable;
1111 reset-n-pins {
1114 output-high;
1115 drive-strength = <16>;
1119 wcd_default: wcd-reset-n-active-state {
1122 drive-strength = <16>;
1123 bias-disable;
1124 output-low;
1127 wwan_sw_en: wwan-sw-en-state {
1130 drive-strength = <4>;
1131 bias-disable;
1136 compatible = "qcom,geni-debug-uart";
1141 vdd-supply = <&vreg_l3j_0p8>;
1142 vdda12-supply = <&vreg_l2j_1p2>;
1150 vdda-phy-supply = <&vreg_l3e_1p2>;
1151 vdda-pll-supply = <&vreg_l1j_0p8>;
1165 remote-endpoint = <&pmic_glink_ss0_hs_in>;
1169 remote-endpoint = <&pmic_glink_ss0_ss_in>;
1173 vdd-supply = <&vreg_l3j_0p8>;
1174 vdda12-supply = <&vreg_l2j_1p2>;
1182 vdda-phy-supply = <&vreg_l3e_1p2>;
1183 vdda-pll-supply = <&vreg_l2d_0p9>;
1197 remote-endpoint = <&pmic_glink_ss1_hs_in>;
1201 remote-endpoint = <&pmic_glink_ss1_ss_in>;
1205 vdd-supply = <&vreg_l3j_0p8>;
1206 vdda12-supply = <&vreg_l2j_1p2>;
1214 vdda-phy-supply = <&vreg_l3e_1p2>;
1215 vdda-pll-supply = <&vreg_l2d_0p9>;
1229 remote-endpoint = <&pmic_glink_ss2_hs_in>;
1233 remote-endpoint = <&pmic_glink_ss2_ss_in>;