Lines Matching +full:headset +full:- +full:mic +full:- +full:bias +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
22 compatible = "qcom,sm8550-mtp", "qcom,sm8550";
23 chassis-type = "handset";
29 wcd938x: audio-codec {
30 compatible = "qcom,wcd9385-codec";
32 pinctrl-names = "default";
33 pinctrl-0 = <&wcd_default>;
35 qcom,micbias1-microvolt = <1800000>;
36 qcom,micbias2-microvolt = <1800000>;
37 qcom,micbias3-microvolt = <1800000>;
38 qcom,micbias4-microvolt = <1800000>;
39 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
40 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
41 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
42 qcom,rx-device = <&wcd_rx>;
43 qcom,tx-device = <&wcd_tx>;
45 reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
47 vdd-buck-supply = <&vreg_l15b_1p8>;
48 vdd-rxtx-supply = <&vreg_l15b_1p8>;
49 vdd-io-supply = <&vreg_l15b_1p8>;
50 vdd-mic-bias-supply = <&vreg_bob1>;
52 #sound-dai-cells = <1>;
56 stdout-path = "serial0:115200n8";
59 pmic-glink {
60 compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
61 #address-cells = <1>;
62 #size-cells = <0>;
63 orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
66 compatible = "usb-c-connector";
68 power-role = "dual";
69 data-role = "dual";
72 #address-cells = <1>;
73 #size-cells = <0>;
79 remote-endpoint = <&usb_1_dwc3_hs>;
87 remote-endpoint = <&usb_dp_qmpphy_out>;
95 remote-endpoint = <&fsa4480_sbu_mux>;
103 compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
104 model = "SM8550-MTP";
105 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
109 "AMIC1", "MIC BIAS1",
110 "AMIC2", "MIC BIAS2",
111 "AMIC3", "MIC BIAS3",
112 "AMIC4", "MIC BIAS3",
113 "AMIC5", "MIC BIAS4",
114 "VA DMIC0", "MIC BIAS1",
115 "VA DMIC1", "MIC BIAS1",
116 "VA DMIC2", "MIC BIAS3",
117 "TX DMIC0", "MIC BIAS1",
118 "TX DMIC1", "MIC BIAS2",
119 "TX DMIC2", "MIC BIAS3",
125 wcd-playback-dai-link {
126 link-name = "WCD Playback";
129 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
133 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
137 sound-dai = <&q6apm>;
141 wcd-capture-dai-link {
142 link-name = "WCD Capture";
145 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
149 sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
153 sound-dai = <&q6apm>;
157 wsa-dai-link {
158 link-name = "WSA Playback";
161 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
165 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
169 sound-dai = <&q6apm>;
173 va-dai-link {
174 link-name = "VA Capture";
177 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
181 sound-dai = <&lpass_vamacro 0>;
185 sound-dai = <&q6apm>;
190 vph_pwr: vph-pwr-regulator {
191 compatible = "regulator-fixed";
192 regulator-name = "vph_pwr";
193 regulator-min-microvolt = <3700000>;
194 regulator-max-microvolt = <3700000>;
196 regulator-always-on;
197 regulator-boot-on;
202 regulators-0 {
203 compatible = "qcom,pm8550-rpmh-regulators";
204 qcom,pmic-id = "b";
206 vdd-bob1-supply = <&vph_pwr>;
207 vdd-bob2-supply = <&vph_pwr>;
208 vdd-l1-l4-l10-supply = <&vreg_s6g_1p8>;
209 vdd-l2-l13-l14-supply = <&vreg_bob1>;
210 vdd-l3-supply = <&vreg_s4g_1p3>;
211 vdd-l5-l16-supply = <&vreg_bob1>;
212 vdd-l6-l7-supply = <&vreg_bob1>;
213 vdd-l8-l9-supply = <&vreg_bob1>;
214 vdd-l11-supply = <&vreg_s4g_1p3>;
215 vdd-l12-supply = <&vreg_s6g_1p8>;
216 vdd-l15-supply = <&vreg_s6g_1p8>;
217 vdd-l17-supply = <&vreg_bob2>;
220 regulator-name = "vreg_bob1";
221 regulator-min-microvolt = <3296000>;
222 regulator-max-microvolt = <3960000>;
223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
227 regulator-name = "vreg_bob2";
228 regulator-min-microvolt = <2720000>;
229 regulator-max-microvolt = <3960000>;
230 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
234 regulator-name = "vreg_l1b_1p8";
235 regulator-min-microvolt = <1800000>;
236 regulator-max-microvolt = <1800000>;
237 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
241 regulator-name = "vreg_l2b_3p0";
242 regulator-min-microvolt = <3008000>;
243 regulator-max-microvolt = <3008000>;
244 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
248 regulator-name = "vreg_l5b_3p1";
249 regulator-min-microvolt = <3104000>;
250 regulator-max-microvolt = <3104000>;
251 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
255 regulator-name = "vreg_l6b_1p8";
256 regulator-min-microvolt = <1800000>;
257 regulator-max-microvolt = <3008000>;
258 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
262 regulator-name = "vreg_l7b_1p8";
263 regulator-min-microvolt = <1800000>;
264 regulator-max-microvolt = <3008000>;
265 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
269 regulator-name = "vreg_l8b_1p8";
270 regulator-min-microvolt = <1800000>;
271 regulator-max-microvolt = <3008000>;
272 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
276 regulator-name = "vreg_l9b_2p9";
277 regulator-min-microvolt = <2960000>;
278 regulator-max-microvolt = <3008000>;
279 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
283 regulator-name = "vreg_l11b_1p2";
284 regulator-min-microvolt = <1200000>;
285 regulator-max-microvolt = <1504000>;
286 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
290 regulator-name = "vreg_l12b_1p8";
291 regulator-min-microvolt = <1800000>;
292 regulator-max-microvolt = <1800000>;
293 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
297 regulator-name = "vreg_l13b_3p0";
298 regulator-min-microvolt = <3000000>;
299 regulator-max-microvolt = <3000000>;
300 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
304 regulator-name = "vreg_l14b_3p2";
305 regulator-min-microvolt = <3200000>;
306 regulator-max-microvolt = <3200000>;
307 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
311 regulator-name = "vreg_l15b_1p8";
312 regulator-min-microvolt = <1800000>;
313 regulator-max-microvolt = <1800000>;
314 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
318 regulator-name = "vreg_l16b_2p8";
319 regulator-min-microvolt = <2800000>;
320 regulator-max-microvolt = <2800000>;
321 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
325 regulator-name = "vreg_l17b_2p5";
326 regulator-min-microvolt = <2504000>;
327 regulator-max-microvolt = <2504000>;
328 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
332 regulators-1 {
333 compatible = "qcom,pm8550vs-rpmh-regulators";
334 qcom,pmic-id = "c";
336 vdd-l3-supply = <&vreg_s4e_0p9>;
339 regulator-name = "vreg_l3c_0p9";
340 regulator-min-microvolt = <880000>;
341 regulator-max-microvolt = <912000>;
342 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
346 regulators-2 {
347 compatible = "qcom,pm8550vs-rpmh-regulators";
348 qcom,pmic-id = "d";
350 vdd-l1-supply = <&vreg_s4e_0p9>;
353 regulator-name = "vreg_l1d_0p88";
354 regulator-min-microvolt = <880000>;
355 regulator-max-microvolt = <920000>;
356 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
360 regulators-3 {
361 compatible = "qcom,pm8550vs-rpmh-regulators";
362 qcom,pmic-id = "e";
364 vdd-l1-supply = <&vreg_s4e_0p9>;
365 vdd-l2-supply = <&vreg_s4e_0p9>;
366 vdd-l3-supply = <&vreg_s4g_1p3>;
367 vdd-s4-supply = <&vph_pwr>;
368 vdd-s5-supply = <&vph_pwr>;
371 regulator-name = "vreg_s4e_0p9";
372 regulator-min-microvolt = <904000>;
373 regulator-max-microvolt = <984000>;
374 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
378 regulator-name = "vreg_s5e_1p1";
379 regulator-min-microvolt = <1080000>;
380 regulator-max-microvolt = <1120000>;
381 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
385 regulator-name = "vreg_l1e_0p88";
386 regulator-min-microvolt = <880000>;
387 regulator-max-microvolt = <880000>;
388 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
392 regulator-name = "vreg_l2e_0p9";
393 regulator-min-microvolt = <904000>;
394 regulator-max-microvolt = <970000>;
395 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
399 regulator-name = "vreg_l3e_1p2";
400 regulator-min-microvolt = <1200000>;
401 regulator-max-microvolt = <1200000>;
402 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
406 regulators-4 {
407 compatible = "qcom,pm8550ve-rpmh-regulators";
408 qcom,pmic-id = "f";
410 vdd-l1-supply = <&vreg_s4e_0p9>;
411 vdd-l2-supply = <&vreg_s4e_0p9>;
412 vdd-l3-supply = <&vreg_s4e_0p9>;
413 vdd-s4-supply = <&vph_pwr>;
416 regulator-name = "vreg_s4f_0p5";
417 regulator-min-microvolt = <500000>;
418 regulator-max-microvolt = <700000>;
419 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
423 regulator-name = "vreg_l1f_0p9";
424 regulator-min-microvolt = <912000>;
425 regulator-max-microvolt = <912000>;
426 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
430 regulator-name = "vreg_l2f_0p88";
431 regulator-min-microvolt = <880000>;
432 regulator-max-microvolt = <912000>;
433 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
437 regulator-name = "vreg_l3f_0p91";
438 regulator-min-microvolt = <880000>;
439 regulator-max-microvolt = <912000>;
440 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
444 regulators-5 {
445 compatible = "qcom,pm8550vs-rpmh-regulators";
446 qcom,pmic-id = "g";
448 vdd-l1-supply = <&vreg_s4g_1p3>;
449 vdd-l2-supply = <&vreg_s4g_1p3>;
450 vdd-l3-supply = <&vreg_s4g_1p3>;
451 vdd-s1-supply = <&vph_pwr>;
452 vdd-s2-supply = <&vph_pwr>;
453 vdd-s3-supply = <&vph_pwr>;
454 vdd-s4-supply = <&vph_pwr>;
455 vdd-s5-supply = <&vph_pwr>;
456 vdd-s6-supply = <&vph_pwr>;
459 regulator-name = "vreg_s1g_1p2";
460 regulator-min-microvolt = <1200000>;
461 regulator-max-microvolt = <1300000>;
462 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
466 regulator-name = "vreg_s2g_0p8";
467 regulator-min-microvolt = <800000>;
468 regulator-max-microvolt = <1000000>;
469 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
473 regulator-name = "vreg_s3g_0p7";
474 regulator-min-microvolt = <300000>;
475 regulator-max-microvolt = <1004000>;
476 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
480 regulator-name = "vreg_s4g_1p3";
481 regulator-min-microvolt = <1200000>;
482 regulator-max-microvolt = <1352000>;
483 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
487 regulator-name = "vreg_s5g_0p8";
488 regulator-min-microvolt = <500000>;
489 regulator-max-microvolt = <1004000>;
490 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
494 regulator-name = "vreg_s6g_1p8";
495 regulator-min-microvolt = <1800000>;
496 regulator-max-microvolt = <2000000>;
497 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
501 regulator-name = "vreg_l1g_1p2";
502 regulator-min-microvolt = <1200000>;
503 regulator-max-microvolt = <1200000>;
504 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
508 regulator-name = "vreg_l2g_1p2";
509 regulator-min-microvolt = <1200000>;
510 regulator-max-microvolt = <1200000>;
511 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
515 regulator-name = "vreg_l3g_1p2";
516 regulator-min-microvolt = <1200000>;
517 regulator-max-microvolt = <1200000>;
518 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
522 regulators-6 {
523 compatible = "qcom,pm8010-rpmh-regulators";
524 qcom,pmic-id = "m";
526 vdd-l1-l2-supply = <&vreg_s4g_1p3>;
527 vdd-l3-l4-supply = <&vreg_bob2>;
528 vdd-l5-supply = <&vreg_s6g_1p8>;
529 vdd-l6-supply = <&vreg_s6g_1p8>;
530 vdd-l7-supply = <&vreg_bob1>;
533 regulator-name = "vreg_l1m_1p056";
534 regulator-min-microvolt = <1056000>;
535 regulator-max-microvolt = <1056000>;
536 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
540 regulator-name = "vreg_l2m_1p056";
541 regulator-min-microvolt = <1056000>;
542 regulator-max-microvolt = <1056000>;
543 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
547 regulator-name = "vreg_l3m_2p8";
548 regulator-min-microvolt = <2800000>;
549 regulator-max-microvolt = <2800000>;
550 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
554 regulator-name = "vreg_l4m_2p8";
555 regulator-min-microvolt = <2800000>;
556 regulator-max-microvolt = <2800000>;
557 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
561 regulator-name = "vreg_l5m_1p8";
562 regulator-min-microvolt = <1800000>;
563 regulator-max-microvolt = <1800000>;
564 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
568 regulator-name = "vreg_l6m_1p8";
569 regulator-min-microvolt = <1800000>;
570 regulator-max-microvolt = <1800000>;
571 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
575 regulator-name = "vreg_l7m_2p9";
576 regulator-min-microvolt = <2800000>;
577 regulator-max-microvolt = <2904000>;
578 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
582 regulators-7 {
583 compatible = "qcom,pm8010-rpmh-regulators";
584 qcom,pmic-id = "n";
586 vdd-l1-l2-supply = <&vreg_s4g_1p3>;
587 vdd-l3-l4-supply = <&vreg_bob2>;
588 vdd-l5-supply = <&vreg_s6g_1p8>;
589 vdd-l6-supply = <&vreg_bob1>;
590 vdd-l7-supply = <&vreg_bob1>;
593 regulator-name = "vreg_l1n_1p1";
594 regulator-min-microvolt = <1104000>;
595 regulator-max-microvolt = <1200000>;
596 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
600 regulator-name = "vreg_l2n_1p1";
601 regulator-min-microvolt = <1104000>;
602 regulator-max-microvolt = <1200000>;
603 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
607 regulator-name = "vreg_l3n_2p8";
608 regulator-min-microvolt = <2800000>;
609 regulator-max-microvolt = <3000000>;
610 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
614 regulator-name = "vreg_l4n_2p8";
615 regulator-min-microvolt = <2800000>;
616 regulator-max-microvolt = <3300000>;
617 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
621 regulator-name = "vreg_l5n_1p8";
622 regulator-min-microvolt = <1800000>;
623 regulator-max-microvolt = <1800000>;
624 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
628 regulator-name = "vreg_l6n_3p3";
629 regulator-min-microvolt = <2800000>;
630 regulator-max-microvolt = <3304000>;
631 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
635 regulator-name = "vreg_l7n_2p96";
636 regulator-min-microvolt = <2800000>;
637 regulator-max-microvolt = <2960000>;
638 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
646 zap-shader {
647 firmware-name = "qcom/sm8550/a740_zap.mbn";
658 typec-mux@42 {
662 vcc-supply = <&vreg_bob1>;
664 mode-switch;
665 orientation-switch;
669 remote-endpoint = <&pmic_glink_sbu>;
676 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
679 drive-strength = <16>;
680 bias-disable;
681 output-low;
684 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
687 drive-strength = <16>;
688 bias-disable;
689 output-low;
698 vdda-supply = <&vreg_l3e_1p2>;
705 pinctrl-names = "default", "sleep";
706 pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
707 pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
709 vddio-supply = <&vreg_l12b_1p8>;
710 vci-supply = <&vreg_l13b_3p0>;
711 vdd-supply = <&vreg_l11b_1p2>;
713 reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
717 remote-endpoint = <&mdss_dsi0_out>;
724 remote-endpoint = <&panel0_in>;
725 data-lanes = <0 1 2 3>;
729 vdds-supply = <&vreg_l1e_0p88>;
738 data-lanes = <0 1>;
742 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
743 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
745 pinctrl-names = "default";
746 pinctrl-0 = <&pcie0_default_state>;
752 vdda-phy-supply = <&vreg_l1e_0p88>;
753 vdda-pll-supply = <&vreg_l3e_1p2>;
759 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
760 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
762 pinctrl-names = "default";
763 pinctrl-0 = <&pcie1_default_state>;
769 vdda-phy-supply = <&vreg_l3c_0p91>;
770 vdda-pll-supply = <&vreg_l3e_1p2>;
771 vdda-qref-supply = <&vreg_l1e_0p88>;
777 sdc2_card_det_n: sdc2-card-det-state {
780 input-enable;
781 output-disable;
782 bias-pull-up;
783 power-source = <1>; /* 1.8 V */
788 vdd18-supply = <&vreg_l15b_1p8>;
789 vdd3-supply = <&vreg_l5b_3p1>;
797 firmware-name = "qcom/sm8550/adsp.mbn",
803 firmware-name = "qcom/sm8550/cdsp.mbn",
809 firmware-name = "qcom/sm8550/modem.mbn",
815 cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
816 pinctrl-names = "default", "sleep";
817 pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
818 pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
819 vmmc-supply = <&vreg_l9b_2p9>;
820 vqmmc-supply = <&vreg_l8b_1p8>;
821 bus-width = <4>;
822 no-sdio;
823 no-mmc;
828 clock-frequency = <32000>;
838 pinctrl-names = "default";
839 pinctrl-0 = <&spkr_1_sd_n_active>;
840 powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>;
841 #sound-dai-cells = <0>;
842 sound-name-prefix = "SpkrLeft";
843 vdd-1p8-supply = <&vreg_l15b_1p8>;
844 vdd-io-supply = <&vreg_l3g_1p2>;
845 qcom,port-mapping = <1 2 3 7 10 13>;
852 pinctrl-names = "default";
853 pinctrl-0 = <&spkr_2_sd_n_active>;
854 powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>;
855 #sound-dai-cells = <0>;
856 sound-name-prefix = "SpkrRight";
857 vdd-1p8-supply = <&vreg_l15b_1p8>;
858 vdd-io-supply = <&vreg_l3g_1p2>;
859 qcom,port-mapping = <4 5 6 7 11 13>;
870 qcom,rx-port-mapping = <1 2 3 4 5>;
881 qcom,tx-port-mapping = <2 2 3 4>;
886 gpio-reserved-ranges = <32 8>;
888 sde_dsi_active: sde-dsi-active-state {
891 drive-strength = <8>;
892 bias-disable;
895 sde_dsi_suspend: sde-dsi-suspend-state {
898 drive-strength = <2>;
899 bias-pull-down;
902 sde_te_active: sde-te-active-state {
905 drive-strength = <2>;
906 bias-pull-down;
909 sde_te_suspend: sde-te-suspend-state {
912 drive-strength = <2>;
913 bias-pull-down;
916 wcd_default: wcd-reset-n-active-state {
919 drive-strength = <16>;
920 bias-disable;
921 output-low;
930 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
931 vcc-supply = <&vreg_l17b_2p5>;
932 vcc-max-microamp = <1300000>;
933 vccq-supply = <&vreg_l1g_1p2>;
934 vccq-max-microamp = <1200000>;
935 vdd-hba-supply = <&vreg_l3g_1p2>;
941 vdda-phy-supply = <&vreg_l1d_0p88>;
942 vdda-pll-supply = <&vreg_l3e_1p2>;
952 remote-endpoint = <&pmic_glink_hs_in>;
956 vdd-supply = <&vreg_l1e_0p88>;
957 vdda12-supply = <&vreg_l3e_1p2>;
965 vdda-phy-supply = <&vreg_l3e_1p2>;
966 vdda-pll-supply = <&vreg_l3f_0p91>;
972 remote-endpoint = <&pmic_glink_ss_in>;
976 clock-frequency = <76800000>;