Lines Matching +full:headset +full:- +full:mic +full:- +full:bias +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
9 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
10 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h>
11 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
12 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
13 #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
24 compatible = "qcom,sm8450-hdk", "qcom,sm8450";
25 chassis-type = "embedded";
31 wcd938x: audio-codec {
32 compatible = "qcom,wcd9385-codec";
34 pinctrl-names = "default";
35 pinctrl-0 = <&wcd_default>;
37 qcom,micbias1-microvolt = <1800000>;
38 qcom,micbias2-microvolt = <1800000>;
39 qcom,micbias3-microvolt = <1800000>;
40 qcom,micbias4-microvolt = <1800000>;
41 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
42 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
43 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
44 qcom,rx-device = <&wcd_rx>;
45 qcom,tx-device = <&wcd_tx>;
47 reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
49 vdd-buck-supply = <&vreg_s10b_1p8>;
50 vdd-rxtx-supply = <&vreg_s10b_1p8>;
51 vdd-io-supply = <&vreg_s10b_1p8>;
52 vdd-mic-bias-supply = <&vreg_bob>;
54 #sound-dai-cells = <1>;
58 stdout-path = "serial0:115200n8";
61 hdmi-out {
62 compatible = "hdmi-connector";
67 remote-endpoint = <<9611_out>;
72 lt9611_1v2: lt9611-vdd12-regulator {
73 compatible = "regulator-fixed";
74 regulator-name = "LT9611_1V2";
76 vin-supply = <&vph_pwr>;
77 regulator-min-microvolt = <1200000>;
78 regulator-max-microvolt = <1200000>;
80 enable-active-high;
83 lt9611_3v3: lt9611-3v3-regulator {
84 compatible = "regulator-fixed";
85 regulator-name = "LT9611_3V3";
87 vin-supply = <&vreg_bob>;
89 regulator-min-microvolt = <3300000>;
90 regulator-max-microvolt = <3300000>;
91 enable-active-high;
94 pmic-glink {
95 compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
96 #address-cells = <1>;
97 #size-cells = <0>;
98 orientation-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
101 compatible = "usb-c-connector";
103 power-role = "dual";
104 data-role = "dual";
107 #address-cells = <1>;
108 #size-cells = <0>;
114 remote-endpoint = <&usb_1_dwc3_hs>;
122 remote-endpoint = <&usb_1_qmpphy_out>;
130 remote-endpoint = <&fsa4480_sbu_mux>;
138 thermal-zones {
139 camera-thermal {
140 polling-delay-passive = <250>;
142 thermal-sensors = <&pmk8350_adc_tm 2>;
145 active-config0 {
153 rear-tof-thermal {
154 polling-delay-passive = <250>;
156 thermal-sensors = <&pmk8350_adc_tm 5>;
159 active-config0 {
167 skin-msm-thermal {
168 polling-delay-passive = <250>;
170 thermal-sensors = <&pmk8350_adc_tm 1>;
173 active-config0 {
181 therm1-thermal {
182 polling-delay-passive = <250>;
184 thermal-sensors = <&pmk8350_adc_tm 3>;
187 active-config0 {
195 therm2-thermal {
196 polling-delay-passive = <250>;
198 thermal-sensors = <&pmk8350_adc_tm 6>;
201 active-config0 {
209 usb-conn-thermal {
210 polling-delay-passive = <250>;
212 thermal-sensors = <&pmk8350_adc_tm 7>;
215 active-config0 {
223 wide-rfc-thermal {
224 polling-delay-passive = <250>;
226 thermal-sensors = <&pmk8350_adc_tm 4>;
229 active-config0 {
237 xo-thermal {
238 thermal-sensors = <&pmk8350_adc_tm 0>;
241 active-config0 {
250 vph_pwr: vph-pwr-regulator {
251 compatible = "regulator-fixed";
252 regulator-name = "vph_pwr";
253 regulator-min-microvolt = <3700000>;
254 regulator-max-microvolt = <3700000>;
256 regulator-always-on;
257 regulator-boot-on;
262 regulators-0 {
263 compatible = "qcom,pm8350-rpmh-regulators";
264 qcom,pmic-id = "b";
266 vdd-s1-supply = <&vph_pwr>;
267 vdd-s2-supply = <&vph_pwr>;
268 vdd-s3-supply = <&vph_pwr>;
269 vdd-s4-supply = <&vph_pwr>;
270 vdd-s5-supply = <&vph_pwr>;
271 vdd-s6-supply = <&vph_pwr>;
272 vdd-s7-supply = <&vph_pwr>;
273 vdd-s8-supply = <&vph_pwr>;
274 vdd-s9-supply = <&vph_pwr>;
275 vdd-s10-supply = <&vph_pwr>;
276 vdd-s11-supply = <&vph_pwr>;
277 vdd-s12-supply = <&vph_pwr>;
279 vdd-l1-l4-supply = <&vreg_s11b_0p95>;
280 vdd-l2-l7-supply = <&vreg_bob>;
281 vdd-l3-l5-supply = <&vreg_bob>;
282 vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
283 vdd-l8-supply = <&vreg_s2h_0p95>;
286 regulator-name = "vreg_s10b_1p8";
287 regulator-min-microvolt = <1800000>;
288 regulator-max-microvolt = <1800000>;
292 regulator-name = "vreg_s11b_0p95";
293 regulator-min-microvolt = <966000>;
294 regulator-max-microvolt = <1104000>;
298 regulator-name = "vreg_s12b_1p25";
299 regulator-min-microvolt = <1350000>;
300 regulator-max-microvolt = <1400000>;
304 regulator-name = "vreg_l1b_0p91";
305 regulator-min-microvolt = <912000>;
306 regulator-max-microvolt = <920000>;
307 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
311 regulator-name = "vreg_l2b_3p07";
312 regulator-min-microvolt = <3072000>;
313 regulator-max-microvolt = <3072000>;
314 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
318 regulator-name = "vreg_l3b_0p9";
319 regulator-min-microvolt = <904000>;
320 regulator-max-microvolt = <904000>;
321 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
325 regulator-name = "vreg_l5b_0p88";
326 regulator-min-microvolt = <880000>;
327 regulator-max-microvolt = <888000>;
328 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
332 regulator-name = "vreg_l6b_1p2";
333 regulator-min-microvolt = <1200000>;
334 regulator-max-microvolt = <1200000>;
335 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
339 regulator-name = "vreg_l7b_2p5";
340 regulator-min-microvolt = <2504000>;
341 regulator-max-microvolt = <2504000>;
342 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
346 regulator-name = "vreg_l9b_1p2";
347 regulator-min-microvolt = <1200000>;
348 regulator-max-microvolt = <1200000>;
349 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
353 regulators-1 {
354 compatible = "qcom,pm8350c-rpmh-regulators";
355 qcom,pmic-id = "c";
357 vdd-s1-supply = <&vph_pwr>;
358 vdd-s2-supply = <&vph_pwr>;
359 vdd-s3-supply = <&vph_pwr>;
360 vdd-s4-supply = <&vph_pwr>;
361 vdd-s5-supply = <&vph_pwr>;
362 vdd-s6-supply = <&vph_pwr>;
363 vdd-s7-supply = <&vph_pwr>;
364 vdd-s8-supply = <&vph_pwr>;
365 vdd-s9-supply = <&vph_pwr>;
366 vdd-s10-supply = <&vph_pwr>;
368 vdd-l1-l12-supply = <&vreg_bob>;
369 vdd-l2-l8-supply = <&vreg_bob>;
370 vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
371 vdd-l6-l9-l11-supply = <&vreg_bob>;
372 vdd-l10-supply = <&vreg_s12b_1p25>;
374 vdd-bob-supply = <&vph_pwr>;
377 regulator-name = "vreg_s1c_1p86";
378 regulator-min-microvolt = <1800000>;
379 regulator-max-microvolt = <2024000>;
383 regulator-name = "vreg_s10c_1p05";
384 regulator-min-microvolt = <1000000>;
385 regulator-max-microvolt = <1100000>;
389 regulator-name = "vreg_bob";
390 regulator-min-microvolt = <3008000>;
391 regulator-max-microvolt = <3960000>;
392 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
396 regulator-name = "vreg_l1c_1p8";
397 regulator-min-microvolt = <1800000>;
398 regulator-max-microvolt = <1800000>;
399 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
403 regulator-name = "vreg_l3c_3p0";
404 regulator-min-microvolt = <3296000>;
405 regulator-max-microvolt = <3304000>;
406 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
410 regulator-name = "vreg_l4c_1p8";
411 regulator-min-microvolt = <1704000>;
412 regulator-max-microvolt = <3000000>;
413 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
417 regulator-name = "vreg_l5c_1p8";
418 regulator-min-microvolt = <1704000>;
419 regulator-max-microvolt = <3000000>;
420 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
424 regulator-name = "vreg_l6c_1p8";
425 regulator-min-microvolt = <1800000>;
426 regulator-max-microvolt = <3008000>;
427 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
431 regulator-name = "vreg_l7c_3p0";
432 regulator-min-microvolt = <3008000>;
433 regulator-max-microvolt = <3008000>;
434 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
438 regulator-name = "vreg_l8c_1p8";
439 regulator-min-microvolt = <1800000>;
440 regulator-max-microvolt = <1800000>;
441 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
445 regulator-name = "vreg_l9c_2p96";
446 regulator-min-microvolt = <2960000>;
447 regulator-max-microvolt = <3008000>;
448 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
452 regulator-name = "vreg_l12c_1p8";
453 regulator-min-microvolt = <1800000>;
454 regulator-max-microvolt = <1968000>;
455 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
459 regulator-name = "vreg_l13c_3p0";
460 regulator-min-microvolt = <3000000>;
461 regulator-max-microvolt = <3000000>;
462 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
466 regulators-2 {
467 compatible = "qcom,pm8450-rpmh-regulators";
468 qcom,pmic-id = "h";
470 vdd-s1-supply = <&vph_pwr>;
471 vdd-s2-supply = <&vph_pwr>;
472 vdd-s3-supply = <&vph_pwr>;
473 vdd-s4-supply = <&vph_pwr>;
474 vdd-s5-supply = <&vph_pwr>;
475 vdd-s6-supply = <&vph_pwr>;
477 vdd-l2-supply = <&vreg_bob>;
478 vdd-l3-supply = <&vreg_bob>;
479 vdd-l4-supply = <&vreg_bob>;
482 regulator-name = "vreg_s2h_0p95";
483 regulator-min-microvolt = <848000>;
484 regulator-max-microvolt = <1104000>;
488 regulator-name = "vreg_s3h_0p5";
489 regulator-min-microvolt = <500000>;
490 regulator-max-microvolt = <500000>;
494 regulator-name = "vreg_l2h_0p91";
495 regulator-min-microvolt = <880000>;
496 regulator-max-microvolt = <912000>;
497 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
501 regulator-name = "vreg_l3h_0p91";
502 regulator-min-microvolt = <912000>;
503 regulator-max-microvolt = <912000>;
504 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
508 regulators-3 {
509 compatible = "qcom,pmr735a-rpmh-regulators";
510 qcom,pmic-id = "e";
512 vdd-s1-supply = <&vph_pwr>;
513 vdd-s2-supply = <&vph_pwr>;
514 vdd-s3-supply = <&vph_pwr>;
516 vdd-l1-l2-supply = <&vreg_s2e_0p85>;
517 vdd-l3-supply = <&vreg_s1e_1p25>;
518 vdd-l4-supply = <&vreg_s1c_1p86>;
519 vdd-l5-l6-supply = <&vreg_s1c_1p86>;
520 vdd-l7-bob-supply = <&vreg_bob>;
523 regulator-name = "vreg_s1e_1p25";
524 regulator-min-microvolt = <1200000>;
525 regulator-max-microvolt = <1296000>;
529 regulator-name = "vreg_s2e_0p85";
530 regulator-min-microvolt = <500000>;
531 regulator-max-microvolt = <1040000>;
535 regulator-name = "vreg_l1e_0p8";
536 regulator-min-microvolt = <800000>;
537 regulator-max-microvolt = <800000>;
541 regulator-name = "vreg_l2e_0p8";
542 regulator-min-microvolt = <800000>;
543 regulator-max-microvolt = <800000>;
547 regulator-name = "vreg_l3e_1p2";
548 regulator-min-microvolt = <1200000>;
549 regulator-max-microvolt = <1200000>;
553 regulator-name = "vreg_l4e_1p7";
554 regulator-min-microvolt = <1776000>;
555 regulator-max-microvolt = <1776000>;
559 regulator-name = "vreg_l5e_0p88";
560 regulator-min-microvolt = <880000>;
561 regulator-max-microvolt = <880000>;
565 regulator-name = "vreg_l6e_1p2";
566 regulator-min-microvolt = <1200000>;
567 regulator-max-microvolt = <1200000>;
571 regulator-name = "vreg_l7e_2p8";
572 regulator-min-microvolt = <2800000>;
573 regulator-max-microvolt = <2800000>;
585 zap-shader {
586 firmware-name = "qcom/sm8450/a730_zap.mbn";
591 clock-frequency = <400000>;
594 lt9611_codec: hdmi-bridge@2b {
598 interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
600 reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
602 vdd-supply = <<9611_1v2>;
603 vcc-supply = <<9611_3v3>;
605 pinctrl-names = "default";
606 pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
609 #address-cells = <1>;
610 #size-cells = <0>;
616 remote-endpoint = <&mdss_dsi0_out>;
624 remote-endpoint = <&hdmi_connector_out>;
632 clock-frequency = <100000>;
636 typec-mux@42 {
640 interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>;
642 vcc-supply = <&vreg_bob>;
643 mode-switch;
644 orientation-switch;
648 remote-endpoint = <&pmic_glink_sbu>;
659 vdda-supply = <&vreg_l6b_1p2>;
664 remote-endpoint = <<9611_a>;
665 data-lanes = <0 1 2 3>;
669 vdds-supply = <&vreg_l5b_0p88>;
678 data-lanes = <0 1>;
683 max-link-speed = <2>;
688 vdda-phy-supply = <&vreg_l5b_0p88>;
689 vdda-pll-supply = <&vreg_l6b_1p2>;
698 vdda-phy-supply = <&vreg_l2h_0p91>;
699 vdda-pll-supply = <&vreg_l6b_1p2>;
703 io-channels = <&pmk8350_vadc PM8350_ADC7_DIE_TEMP(1)>;
704 io-channel-names = "thermal";
708 io-channels = <&pmk8350_vadc PM8350B_ADC7_DIE_TEMP>;
709 io-channel-names = "thermal";
713 io-channels = <&pmk8350_vadc PMR735A_ADC7_DIE_TEMP>;
714 io-channel-names = "thermal";
720 xo-therm@0 {
722 io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
724 qcom,hw-settle-time-us = <200>;
727 skin-msm-therm@1 {
729 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
731 qcom,hw-settle-time-us = <200>;
734 camera-therm@2 {
736 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
738 qcom,hw-settle-time-us = <200>;
741 therm1-therm@3 {
743 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
745 qcom,hw-settle-time-us = <200>;
748 wide-rfc-therm@4 {
750 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
752 qcom,hw-settle-time-us = <200>;
755 rear-tof-therm@5 {
757 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
759 qcom,hw-settle-time-us = <200>;
762 therm2-therm@6 {
764 io-channels = <&pmk8350_vadc PM8350_ADC7_GPIO3_100K_PU(1)>;
766 qcom,hw-settle-time-us = <200>;
769 usb-conn-therm@7 {
771 io-channels = <&pmk8350_vadc PM8350B_ADC7_AMUX_THM5_100K_PU>;
773 qcom,hw-settle-time-us = <200>;
787 qcom,hw-settle-time = <200>;
799 qcom,hw-settle-time = <200>;
806 qcom,hw-settle-time = <200>;
813 qcom,hw-settle-time = <200>;
820 qcom,hw-settle-time = <200>;
827 qcom,hw-settle-time = <200>;
834 qcom,hw-settle-time = <200>;
846 qcom,hw-settle-time = <200>;
858 qcom,hw-settle-time = <200>;
865 qcom,hw-settle-time = <200>;
873 firmware-name = "qcom/sm8450/adsp.mbn";
878 firmware-name = "qcom/sm8450/cdsp.mbn";
883 firmware-name = "qcom/sm8450/modem.mbn";
888 firmware-name = "qcom/sm8450/slpi.mbn";
900 cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
901 pinctrl-names = "default", "sleep";
902 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
903 pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
904 vmmc-supply = <&vreg_l9c_2p96>;
905 vqmmc-supply = <&vreg_l6c_1p8>;
906 no-sdio;
907 no-mmc;
912 compatible = "qcom,sm8450-sndcard";
913 model = "SM8450-HDK";
914 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
918 "AMIC1", "MIC BIAS1",
919 "AMIC2", "MIC BIAS2",
920 "AMIC3", "MIC BIAS3",
921 "AMIC4", "MIC BIAS3",
922 "AMIC5", "MIC BIAS4",
923 "VA DMIC0", "MIC BIAS3",
924 "VA DMIC1", "MIC BIAS3",
925 "VA DMIC2", "MIC BIAS1",
926 "VA DMIC3", "MIC BIAS1",
927 "TX DMIC0", "MIC BIAS3",
928 "TX DMIC1", "MIC BIAS3",
929 "TX DMIC2", "MIC BIAS1",
930 "TX DMIC3", "MIC BIAS1",
936 wcd-playback-dai-link {
937 link-name = "WCD Playback";
940 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
944 sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
948 sound-dai = <&q6apm>;
952 wcd-capture-dai-link {
953 link-name = "WCD Capture";
956 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
960 sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
964 sound-dai = <&q6apm>;
968 wsa-dai-link {
969 link-name = "WSA Playback";
972 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
976 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
980 sound-dai = <&q6apm>;
984 va-dai-link {
985 link-name = "VA Capture";
988 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
992 sound-dai = <&vamacro 0>;
996 sound-dai = <&q6apm>;
1007 pinctrl-names = "default";
1008 pinctrl-0 = <&spkr_1_sd_n_active>;
1009 powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
1010 #sound-dai-cells = <0>;
1011 sound-name-prefix = "SpkrLeft";
1012 #thermal-sensor-cells = <0>;
1013 vdd-supply = <&vreg_s10b_1p8>;
1019 pinctrl-names = "default";
1020 pinctrl-0 = <&spkr_2_sd_n_active>;
1021 powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
1022 #sound-dai-cells = <0>;
1023 sound-name-prefix = "SpkrRight";
1024 #thermal-sensor-cells = <0>;
1025 vdd-supply = <&vreg_s10b_1p8>;
1035 qcom,rx-port-mapping = <1 2 3 4 5>;
1045 qcom,tx-port-mapping = <1 1 2 3>;
1050 gpio-reserved-ranges = <28 4>, <36 4>;
1052 lt9611_irq_pin: lt9611-irq-state {
1055 bias-disable;
1058 lt9611_rst_pin: lt9611-rst-state {
1061 output-high;
1064 sdc2_card_det_n: sd-card-det-n-state {
1067 drive-strength = <2>;
1068 bias-pull-up;
1079 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
1081 vcc-supply = <&vreg_l7b_2p5>;
1082 vcc-max-microamp = <1100000>;
1083 vccq-supply = <&vreg_l9b_1p2>;
1084 vccq-max-microamp = <1200000>;
1085 vdd-hba-supply = <&vreg_l9b_1p2>;
1091 vdda-phy-supply = <&vreg_l5b_0p88>;
1092 vdda-pll-supply = <&vreg_l6b_1p2>;
1101 usb-role-switch;
1105 remote-endpoint = <&pmic_glink_hs_in>;
1111 vdda-pll-supply = <&vreg_l5b_0p88>;
1112 vdda18-supply = <&vreg_l1c_1p8>;
1113 vdda33-supply = <&vreg_l2b_3p07>;
1119 vdda-phy-supply = <&vreg_l6b_1p2>;
1120 vdda-pll-supply = <&vreg_l1b_0p91>;
1124 remote-endpoint = <&pmic_glink_ss_in>;
1128 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
1129 pinctrl-names = "default";
1130 vdd-micb-supply = <&vreg_s10b_1p8>;
1131 qcom,dmic-sample-rate = <600000>;
1137 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
1140 drive-strength = <16>;
1141 bias-disable;
1142 output-low;
1145 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
1148 drive-strength = <16>;
1149 bias-disable;
1150 output-low;
1153 wcd_default: wcd-reset-n-active-state {
1156 drive-strength = <16>;
1157 bias-disable;
1158 output-low;