dts/qcom/msm8992-lg-h815.dts

1 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
8 /dts-v1/;
13 #include <dt-bindings/leds/common.h>
16 /delete-node/ &cont_splash_mem;
19 /delete-node/ &dfps_data_mem;
24 	chassis-type = "handset";
26 	qcom,msm-id = <0xfb 0x0>;
27 	qcom,pmic-id = <0x10009 0x1000a 0x0 0x0>;
28 	qcom,board-id = <0xb64 0x0>;
31 	/delete-node/ psci;
33 	reserved-memory {
34 		#address-cells = <2>;
35 		#size-cells = <2>;
38 		spin-table@6000000 {
40 			no-map;
46 			console-size = <0x20000>;
47 			pmsg-size = <0x20000>;
48 			record-size = <0x10000>;
49 			ecc-size = <0x10>;
54 			no-map;
57 		crash_fb_mem: crash-fb@4000000 {
59 			no-map;
63 	gpio-hall-sensor {
64 		compatible = "gpio-keys";
66 		pinctrl-0 = <&hall_sensor_default>;
67 		pinctrl-names = "default";
71 		event-hall-sensor {
74 			linux,input-type = <EV_SW>;
76 			linux,can-disable;
77 			wakeup-source;
81 	gpio-keys {
82 		compatible = "gpio-keys";
84 		key-vol-up {
88 			wakeup-source;
89 			debounce-interval = <15>;
95 	enable-method = "spin-table";
99 	enable-method = "spin-table";
103 	enable-method = "spin-table";
107 	enable-method = "spin-table";
111 	enable-method = "spin-table";
115 	enable-method = "spin-table";
124 	regulators-0 {
125 		compatible = "qcom,rpm-pm8994-regulators";
127 		vdd_s3-supply = <&vph_pwr>;
128 		vdd_s4-supply = <&vph_pwr>;
129 		vdd_s5-supply = <&vph_pwr>;
130 		vdd_s7-supply = <&vph_pwr>;
131 		vdd_l1-supply = <&pmi8994_s1>;
132 		vdd_l2_26_28-supply = <&pm8994_s3>;
133 		vdd_l3_11-supply = <&pm8994_s3>;
134 		vdd_l4_27_31-supply = <&pm8994_s3>;
135 		vdd_l5_7-supply = <&pm8994_s5>;
136 		vdd_l6_12_32-supply = <&pm8994_s5>;
137 		vdd_l8_16_30-supply = <&vph_pwr>;
138 		vdd_l9_10_18_22-supply = <&pmi8994_bby>;
139 		vdd_l13_19_23_24-supply = <&pmi8994_bby>;
140 		vdd_l14_15-supply = <&pm8994_s5>;
141 		vdd_l17_29-supply = <&pmi8994_bby>;
142 		vdd_l20_21-supply = <&pmi8994_bby>;
143 		vdd_l25-supply = <&pm8994_s5>;
144 		vdd_lvs1_2-supply = <&pm8994_s4>;
147 			regulator-min-microvolt = <1300000>;
148 			regulator-max-microvolt = <1300000>;
153 			regulator-min-microvolt = <1800000>;
154 			regulator-max-microvolt = <1800000>;
155 			regulator-system-load = <325000>;
156 			regulator-allow-set-load;
160 			regulator-min-microvolt = <2150000>;
161 			regulator-max-microvolt = <2150000>;
166 			regulator-min-microvolt = <1800000>;
167 			regulator-max-microvolt = <2950000>;
168 			regulator-system-load = <22000>;
169 			regulator-allow-set-load;
174 			regulator-min-microvolt = <2950000>;
175 			regulator-max-microvolt = <2950000>;
176 			regulator-system-load = <570000>;
177 			regulator-allow-set-load;
182 			regulator-min-microvolt = <2950000>;
183 			regulator-max-microvolt = <2950000>;
184 			regulator-system-load = <800000>;
185 			regulator-allow-set-load;
189 	regulators-1 {
190 		compatible = "qcom,rpm-pmi8994-regulators";
192 		vdd_s1-supply = <&vph_pwr>;
193 		vdd_bst_byp-supply = <&vph_pwr>;
196 			regulator-min-microvolt = <1025000>;
197 			regulator-max-microvolt = <1025000>;
200 		/* S2 & S3 - VDD_GFX */
202 		pmi8994_bby: boost-bypass {
203 			regulator-min-microvolt = <3150000>;
204 			regulator-max-microvolt = <3600000>;
210 	mmc-hs400-1_8v;
211 	vmmc-supply = <&pm8994_l20>;
212 	vqmmc-supply = <&pm8994_s4>;
213 	non-removable;
218 	vmmc-supply = <&pm8994_l21>;
219 	vqmmc-supply = <&pm8994_l13>;
220 	cd-gpios = <&pm8994_gpios 8 GPIO_ACTIVE_LOW>;
225 	hall_sensor_default: hall-sensor-default-state {
228 		drive-strength = <2>;
229 		bias-pull-up;